Two forces act on the screw eye. If F = 600 N, determine the magnitude of the resultant force and the angle θ if the resultant force is directed vertically upward.

Answer:

Option (a), (d) are correct.

Explanation:

Frequency, f = 220 Hz

Resonant frequency = 660 Hz

The next frequency of stopped organ pipe is

2f, 3 f, 4 f ....

= 2 x 220 , 3 x 220 , 4 x 220 ....

= 440 Hz, 660 Hz, 880 Hz

So, the option (a) is correct.

The next resonant frequency of open organ pipe is

3 f, 5 f,...

= 3 x 220, 5 x 220 , ..

= 660 Hz, 1100 Hz,...

So, option (d) is correct.

Answer:

mass

Explanation:

Answer:

The inductance is 17784.96 ohm and rms current is 4.77 mA.

Explanation:

Voltage, V = 120 V

frequency, f = 60 Hz

Inductance, L = 47.2 H

The rms  voltage is

[tex]V_{rms}=\frac{V_o}{\sqrt 2}\\\\V_{rms}=\frac{120}{\sqrt 2}\\\\V_{rms} = 84.87 V[/tex]

The reactance is given by

[tex]X_L = 2\pi f L\\\\X_L = 2\times 3.14\times 60\times 47.2 \\\\X_L = 17784.96 ohm[/tex]

The rms current is

[tex]I_{rms} =\frac{V_{rms}}{X_L}\\\\I_{rms}=\frac{84.87}{17784.96}\\\\I_{rms} = 4.77\times 10^{-3} A = 4.77 mA[/tex]

Answer:

1

Explanation:

Electrolysis is the passing of an current through a conducting solution, when the occurs, a chemical reaction takes place.

Heating a chemical will always cause a chemical reaction, which is why 3 is also correct

Some information as to why 2 is NOT correct.

2 is NOT a chemical reaction, but rather a process of physical separation. It uses selective boiling and condensation, but is not considered a chemical reaction.

as with 3, heating is not considered a chemical reaction, but rather a physical temperature change. This is always what it is considered to be (e.g boiling water is a physical temperature change, not a chemical reaction)

Hope this helps.

Hope this helps.

Answer:

temperature

Explanation:

temperature change forms different elements and different element sustain different colour

Answer:

Smaller and upside down

Explanation:

To answer the question, we must recognise that the characteristics of the image formed by a convex lens depends on the position of the object from the lens.

From the diagram given in the question above, the following data were obtained:

1. The image is smaller than the object.

2. The image is inverted i.e upside down.

3. The image is closer to the lens

4. The image between 2f and f

Now, considering the options given in question above, the correct answer to the question is:

The image is smaller and upside down.

Answer: See attached pic. Hope this helps.

Explanation:

Explanation:

No matter where you are in the universe, your mass is always the same: mass is a measure of the amount of matter which makes up an object. Weight, however, changes because it is a measure of the force between an object and body on which an object resides (whether that body is the Earth, the Moon, Mars, et cetera).

Explanation:

Hence, weight of a body will change from one place to another place because the value of g is different in different places. For example, the value of g on moon is 1/6 times of the value of g on earth. As mass is independent of g , so it will not change from place to place.

Answer:

the current that flows through the component is 2.42 A

Explanation:

Given;

resistance of the electrical component, r = 53 Ω

the voltage of the source, V = 128 V

The current that flows through the component is calculated using Ohm's Law as demonstrated below;

[tex]V = IR\\\\I = \frac{V}{R} = \frac{128 \ V}{53 \ ohms} = 2.42 \ A[/tex]

Therefore, the current that flows through the component is 2.42 A

Answer:

A. You find sheets of copper (Cu) used in an induced rescue factory scene

Explanation:

I would use a sheets of copper (Cu) used in an induced rescue factory scene because, copper is a metal and the only material out of the other options that would only dent and not crumble when hit by the lead pipe.

The other options in B - D are non-metals.

Phosphorus is a non-metal and is used as an explosive and thus cannot be used.

Helium is a gas used in filling balloons and thus cannot be used.

Chlorine is used in killing bacteria and thus cannot be used.

So, copper is the only option available since it is a metal and can thus accommodate a large force.

So, option A is the answer.

Explanation:

Displacement of a body moving in circular motion is called uniform circular motion.

hope it is helpful to you

Answer:

A constantly moving object with consistent circular movement. However, for its change in direction, it is accelerating

Explanation:

Uniform circular motion in a circle at constant rate can be described as the motion of the object. When an object moves in a circle, it changes its direction constantly. The object moves tangently to the circle at all times. As the velocity vector direction is the same as the object motion direction, the velocity vector is tangent to the circle. This is shown in the animation on the right by a vector arrow.

An item is accelerating that moves in a circle. Objects that accelerate are subjects that change their speed – either the velocity (i.e. the vecteur magnitude) or the direction. An object with consistent circular movement moves at a constant speed. However, because of its change in direction, it is accelerating. The acceleration direction is inside. The animation on the right shows this through a vector arrow

For an object with only a uniform circular movement, the final motion is the net force. The The net force acting on this object is directed to the middle of the circle. The net force is an inner or centripetal force. Without such a deepest force, an object would continue in a straight direction, never deviating. Regrettably, with the inward net force, perpendicular to the vector, the object changes the direction and is accelerated internally.

Answer:

P = 6.63 kW

Explanation:

Given that,

Current, I = 260 A

Voltage of the battery, V = 25.5 V

We need to find the power supplied to the starter motor. We know that,

P = VI

Put all the values,

P = 25.5 × 260

P = 6630 W

or

P = 6.63 kW

So, the power supplied to the motor is 6.63 kW.

Answer:

The power is 6.63 kW.

Explanation:

Current, I = 260  A

Voltage, V = 25.5 V

Power of an electrical appliance is given by

P = V I

P = 25.5 x 260

P = 6630 W

1 kW = 1000 W

So, the power is

P = 6.63 kW

Answer:

0.001 A

Explanation:

Applying,

V = IR.............. Equation 1

Where V = Voltage of the motor, I = current, R = resistance

make I the subject of the equation

I = V/R.............. Equation 2

From the question,

Given: V = 1000 V, R = 1 MΩ = 10⁶ Ω

Substitute these values into equation 2

I = 1000/10⁶

I = 10⁻³ A

I = 0.001 A

Answer:

Jupiter

Explanation:

Answer:

The answer is Jupiter.

Explanation:

Jupiter is an orange/yellow colored planet.

Answer:

[tex]P=17658Pa[/tex]

Explanation:

From the question we are told that:

Dimension

 [tex]L*B=27.0*8.9[/tex]

Depth [tex]d=1.8m[/tex]

Generally the equation for Volume of water is mathematically given by

 [tex]V=L*B*D[/tex]

 [tex]V=27.0*8.9*1.8[/tex]

 [tex]V=432.54m^3[/tex]

Therefore

Force at the bottom of the Pool

 [tex]F=\rho Vg[/tex]

Where

 [tex]\rho \ density\ of \ water(1000kg/m^3)[/tex]

 [tex]F=1000*432.54m^3*9.81[/tex]

 [tex]F=4.2*10^{6}N[/tex]

Generally the equation for Pressure at the bottom is mathematically given by

 [tex]P=\frac{Forece }{Area}[/tex]

 [tex]P=\frac{4.2*10^{6}N}{27.0*8.9}[/tex]

 [tex]P=17658Pa[/tex]

Answer:

Explanation:

Intensity of sound = sound energy emitted by source / 4 π d² , where d is distance of the source .

A )

Intensity of sound at 1 m distance = 60 /4 π d²

d = 1 m

Intensity of sound at 1 m distance = 60 /(4 π 1²)

= 4.78 W m⁻² s⁻¹

B )

Intensity of sound at 1.5 m distance = 60 /4 π d²

d = 1.5  m

Intensity of sound at 1 m distance = 60 /(4 π 1.5²)

= 2.12 W m⁻² s⁻¹

C )

Intensity of sound due to 4 speakers at 1.5 m distance = 4 x 60 /4 π d²

d = 1.5  m

= 4 x 60 /(4 π 1.5²)

= 8.48 W m⁻² s⁻¹

D )

Intensity of sound due to .06 W speaker must be 10⁻¹² W s ⁻² . Let the distance be d .

.06 /4 π d² = 10⁻¹²

d² = .06 /4 π 10⁻¹²

d = 6.9 x 10⁴ m .

Explanation:

Forces on Block A:

Let the x-axis be (+) towards the right and y-axis be (+) in the upward direction. We can write the net forces on mass [tex]m_A[/tex] as

[tex]x:\:\:(F_{net})_x = f_N - T = -m_Aa\:\:\:\:\:\:\:(1)[/tex]

[tex]y:\:\:(F_{net})_y = N - m_Ag = 0 \:\:\:\:\:\:\:\:\:(2)[/tex]

Substituting (2) into (1), we get

[tex]\mu_km_Ag - T = -m_Aa \:\:\:\:\:\:\:\:\:(3)[/tex]

where [tex]f_N= \mu_kN[/tex], the frictional force on [tex]m_A.[/tex] Set this aside for now and let's look at the forces on [tex]m_B[/tex]

Forces on Block B:

Let the x-axis be (+) up along the inclined plane. We can write the forces on [tex]m_B[/tex] as

[tex]x:\:\:(F_{net})_x = T - m_B\sin30= -m_Ba\:\:\:\:\:\:\:(4)[/tex]

[tex]y:\:\:(F_{net})_y = N - m_Bg\cos30 = 0 \:\:\:\:\:\:\:\:\:(5)[/tex]

From (5), we can solve for N as

[tex]N = m_B\cos30 \:\:\:\:\:\:\:\:\:(6)[/tex]

Set (6) aside for now. We will use this expression later. From (3), we can see that the tension T is given by

[tex]T = m_A( \mu_kg + a)\:\:\:\:\:\:\:\:\:(7)[/tex]

Substituting (7) into (4) we get

[tex]m_A(\mu_kg + a) - m_Bg\sin 30 = -m_Ba[/tex]

Collecting similar terms together, we get

[tex](m_A + m_B)a = m_Bg\sin30 - \mu_km_Ag[/tex]

or

[tex]a = \left[ \dfrac{m_B\sin30 - \mu_km_A}{(m_A + m_B)} \right]g\:\:\:\:\:\:\:\:\:(8)[/tex]

Putting in the numbers, we find that [tex]a = 1.4\:\text{m/s}[/tex]. To find the tension T, put the value for the acceleration into (7) and we'll get [tex]T = 21.3\:\text{N}[/tex]. To find the force exerted by the inclined plane on block B, put the numbers into (6) and you'll get [tex]N = 50.9\:\text{N}[/tex]

Answer:

C. When an object floats, it does not displace its entire volume.

Explanation:

Buoyancy can be defined as an upward force which is created by the water displaced by an object.

According to Archimede's principle, it is directly proportional to the amount (weight) of water that is being displaced by an object.

Basically, the greater the amount of water an object displaces; the greater is the force of buoyancy pushing the object up. The buoyancy of an object is given by the formula;

[tex] Fb = pgV [/tex]

[tex] But, \; V = Ah [/tex]

[tex] Hence, \; Fb = pgAh [/tex]

Where;

Fb = buoyant force of a liquid acting on an object.

g = acceleration due to gravity.

p = density of the liquid.

v = volume of the liquid displaced.

h = height of liquid (water) displaced by an object.

A = surface area of the floating object.

The unit of measurement for buoyancy is Newton (N).

Additionally, the density of a fluid is directly proportional to the buoyant force acting on it i.e as the density of a liquid decreases, buoyancy decreases and vice-versa.

Furthermore, an object such as a boat, ship, ferry, canoe, etc, are able to float because the volume of water they displace weigh more than their own weight. Thus, if a boat or any physical object weighs more than the volume of water it displaces, it would sink; otherwise, it floats.

In conclusion, the true statement is that when an object floats, it does not displace its entire volume.

The desk is in equilbrium, so Newton's second law gives

∑ F (horizontal) = p - f = 0

∑ F (vertical) = n - mg = 0

==>   n = mg

==>   p = f = µn = µmg = 0.400 (80.0 kg) g = 313.6 N

The student pushes the desk 3.00 m, so she performs

W = (313.6 N) (3.00 m) = 940.8 Nm ≈ 941 J

of work.

Answer:

Measurements allow people to find their way to new places. Measurements such as miles or kilometers are used by GPS systems to give directions. Time measurements help to create schedules so tasks get done on time. Measurements are used in food as well. Ingredients in recipes have to be measured to make the dish correctly. Serving sizes are a measurement that keep people healthy by showing how much of each food you should eat.

Answer:

The car travels the distance of 225m before it comes to rest.

Explanation:

Given,

v = 45m/s

t = 5s

Therefore,

d = v × t

= 45 × 5

= 225m

Answer:

[tex]\alpha=-3.01dB[/tex]

Explanation:

From the question we are told that:

Sound level intensity

 [tex]\triangle I=40dB-80dB[/tex]

Generally the equation for  intensity level  is mathematically given by

 [tex]\alpha=10log_{10}(I/I_x)dB[/tex]

Where

 I= Intensity measured

 [tex]I_x=Threshold\ of\ audibility[/tex]

 [tex]I_x= 10-12 W / m2[/tex]

 [tex]\alpha= 10 log10 \frac{I_1}{I_x} - 10 log10 \frac{}I_2{I_x}[/tex]

 [tex]\alpha= 10 log10 \frac{I_1}{I_2}[/tex]

 [tex]\alpha=10 log10\frac{40}{80}[/tex]

 [tex]\alpha=-3.01dB[/tex]

[tex] \orange{\underline{\huge{\bold{\textit{\green{\bf{QUESTION}}}}}}}[/tex]

Why is the temperature constant during the melting of water?

[tex] \huge\mathbb{\red A \pink{N}\purple{S} \blue{W} \orange{ER}}[/tex]

[tex] \orange{\underline{\huge{\bold{\textit{\green{\bf{ REASON}}}}}}}[/tex]

THE HEAT WE R SUPPLYING TO THE WATER TO RAISE THE TEMP OF THE WATER IS USED BY THE MOLECULES TO BREAK INTERMOLECULAR BONDS WHICH HELP IN THE CHANGING OF THE LATTICE (STRUCTURE) OF THE WATER .

ICE HAS A HEXAGONAL RING LIKE STRUCTURE WHICH IS CONVERTED INTO REGULAR CRYSTALLINE STRUCTURE WHICH CAN ONLY BE FORMED WITH THE HELP OF FORMATION OF NEW BONDS AND BREAKDOWN OF OLDER ONES

THE AMOUNT OF ENERGY WHICH IS USED IN CONVERSATION OF THE STATE OF FROM SOLID TO LIQUID IS KNOWN AS LATENT HEAT OF FUSION.

SO TEMP REMAIN CONSTANT DURING CHANGE IN STATE .

[tex] \red \star{Thanks \: And \: Brainlist} \blue\star \\ \green\star If \: U \: Liked \: My \: Answer \purple \star[/tex]

Answer:

Heat is flowing into the metal.

Explanation:

From the question given above, the following data were obtained:

Mass (M) of iron = 150 g

Initial temperature (T₁) = 25.0°C

Final temperature (T₂) = 73.3°C

Direction of heat flow =?

Next, we shall determine the change in the temperature of iron. This can be obtained as follow:

Initial temperature (T₁) = 25.0 °C

Final temperature (T₂) = 73.3 °C

Change in temperature (ΔT) =?

ΔT = T₂ – T₁

ΔT = 73.3 – 25

ΔT = 48.3 °C

Next, we shall determine the heat transfered. This can be obtained as follow:

Mass (M) of iron = 150 g

Change in temperature (ΔT) = 48.3 °C

Specific heat capacity (C) of iron = 0.450 J/gºC

Heat (Q) transfered =?

Q = MCΔT

Q = 150 × 0.450 × 48.3

Q = 3260.25 J

Since the heat transferred is positive, it means the iron metal is absorbing the heat. Thus, heat is flowing into the metal.

Answer:The SI system is based on the number 10 as well as multiples and products of 10. This makes it much easier to use, and so it has been the accepted system in scientific and technical applications. The English system is more complicated as relationships between units of the same quantity aren't uniform.

Explanation:

Answer:

The metric system is an internationally agreed decimal system of measurement while The International System of Units (SI) is the official system of measurement in almost every country in the world

Answer:

a)   a = 91.4 m / s²,  b)    t = 0.175 s, c)  

Explanation:

a) This is a kinematics exercise

           v² = vox ² + 2a (x-xo)

           a = v² - 0/2 (x-0)

let's calculate

          a = 16² / 2 1.4

          a = 91.4 m / s²

b) the shooting time

          v = vox + a t

          t = v-vox / a

          t = 16 / 91.4

          t = 0.175 s

c) let's use Newton's second law

          F = ma

          F = 7.9 91.4

          F = 733 N