This type of collision is known as an Inelastic collision.
The speed rate at which car a used is more higher than that of car b because of its friction.
I hope this helps.
Which nutrients are needed in soil in larger doses?
Mineral Nutrients
Macronutrients
Non-mineral Nutrients
Micronutrients
Answer:
The primary nutrients are nitrogen, phosphorus and potassium.
The intermediate nutrients are sulfur, magnesium, and calcium.
The remaining essential elements are the micronutrients and are required in very small quantities.
Answer:
The primary nutrients are nitrogen, phosphorus and potassium.
The intermediate nutrients are sulfur, magnesium, and calcium.
The remaining essential elements are the micronutrients and are required in very small quantities.
Explanation:
An elevator of 3 × 10^4N is raised to a height of 100m in 20s . The work done by electric motor is equivalent to?
Answer:
there it is fella tried on ma own observation
The unit of area is a derived unit. Why?
Explanation:
area=length(m) ×breadth(m) . The unit of area is expressed in terms of fundamental units m^2.thus it is derived unit
Brass is made by melting a mixture which contain 67% by mass of copper and 33% by mass of zinc if no change in volume.Calculate the density of brass
Answer:
The density of brass is approximately 8,261.73 kg/m³
Explanation:
The percentage composition by mass of brass is given as follows;
The percentage by mass of copper = 67%
The percentage by mass of zinc = 33%
The density of copper, ρ₁ = 8.96 g/cm³
The density of zinc, ρ₂ = 7.133 g/cm³
Therefore, where we have, m = 100 g of brass, we have;
The mass of copper, m₁ = 67 g
The volume of copper, V₁ = m₁/ρ₁
∴ V₁ = 67 g/(8.96 g/cm³) ≈ 7.47767857 cm³
The volume of zinc, V₂ = m₂/ρ₂
∴ V₂ = 33 g/(7.133 g/cm³) ≈ 4.62638411 cm³
The volume of the brass, V = V₁ + V₂
V = 7.47767857 cm³ + 4.62638411 cm³ ≈ 12.104 cm³
The density of brass, ρ = m/V
∴ ρ = 100 g/(12.104 cm³) ≈ 8.26 g/cm³
The density of brass, ρ ≈ 8.26 g/cm³ = 8,261.73 kg/m³
outs each inning?
Each team gets (how many).
o 2
3
(Basketball )
Help!!
?
used to measure temperature
used to measure force
prefix that means 1/100
prefix that means 1,000
prefix that means 1/1,000
Answer:
prefix that means 1/100 = Centi
prefix that means 1,000 = Kilo
prefix that means 1/1000 = Milli
Explanation:
A student starts a stop-watch when the bob reaches to point M.He counts each time the bob changes direction and stop the watch on the tenth change in direction.The watch shows a time of 12.0 seconds.calculate the time period
Answer:
m
Explanation:
.
DO U KNOW CARRYMINATI
value of the refractive index of lens is 2.5 The curved surfaces are having The radius of curvature 10 cm and -12cm Out The focal length of the lens respectively find out the focal length of the lens?
Answer:
4
dhsfb ffhgchbvffffggcg
Answer:
16.5
Explanation:
A student starts at position (4,4) m and undergoes three displacements:
d1 = (2, -3) m, d2 = (-5, 0) m, and d3 = (1, 6) m.
What is the final position of the student? Show your solution graphically and numerically.
please help!!
Answer:
The final position is (2, 7)m
Explanation:
When we work with coordinate pairs, the addition works as:
(a, b) + (c, d) = (a + c, b + d)
So, for example, if we start at (a, b), and we have a displacement d = (1, 1)
we just need to solve:
(a, b) + (1, 1) = (a + 1, b + 1)
Now, in this case, we start at (4, 4)m
first, we have d1 = (2, -3) m
After this displacement, the position is:
(4, 4)m + (2, -3)m = (4 + 2, 4 - 3)m = (6, 1)m
Now we have a displacement d2 = (-5, 0) m
After this, the position is:
(6, 1)m + (-5, 0)m = (6 -5, 1 + 0)m = (1, 1)m
After this, we have the final displacement d3 = (1, 6) m, so the final position will be:
(1, 1)m + (1, 6)m = (1 + 1, 1 + 6)m = (2, 7)m
Below you can see a rough sketch of the path that the student take, where he/she starts at point A.
A 75.0 kg man pushes backward on a 300.0 kg boat with a force of 150.0N causing the boat to accelerate backward at 0.5m/s^2. What is the acceleration of the man?
A) 150.0 m/s^2
B) 8.00 m/s^2
C) 2.00 m/s^2
D) 4.00 m/s^2
Answer:
C) 2.00 m/s^2
Explanation:
F = m*a
150N = 75kg(a)
a = 150N/75kg
a = 2.0m/s²
Which of these is untrue about ray diagrams?
A. The arrowheads show the direction of the light
B. Lines must always be straight
C. More arrowheads on lines mean a brighter light
Answer:
The untrue option is C: "More arrowheads on lines mean a brighter light"
Explanation:
Ray diagrams are used to show how the light behaves with things like mirrors or lenses. Where we only study how the direction of the light changes when it interacts with these objects.
The "light" is represented with arrows, where again, the only thing we care is the direction of the light, so the first statement is true, the arrowheads show the direction of the light, and only that.
The intensity of the light, in this context, has no effect on how light behaves, so there is not a necessity of representing the intensity of the light, thus, more arrowheads on lines do not mean a brighter light. It may only be used to represent changes in direction of the light.
Finally, we know that light travels in straight pats (the pats can be curved in some cases, like with large gravitational fields, but this is not the case of a ray diagram) so the lines that represent the light should always be straight, thus option B is also true.
The untrue option is C: "More arrowheads on lines mean a brighter light"
which of the following items has the most inertia while at rest
Answer:
wats the following items
(Please help if you can, I need this last answer done by tonight.)
Use the universal law of gravitation to solve the following problem.
Hint: mass of the Earth is = 5.97 x 1024 kg
A scientific satellite of mass 1300 kg orbits Earth 200 km above its surface. If Earth has a radius of 6378 km, what is the force of gravity acting on the scientific satellite?
a. Write out the formula for this problem.
b. Plug in the values from this problem into the formula.
c. Solve the problem, writing out each step.
d. Correct answer
Answer:
a.
[tex]F =G \cdot \dfrac{M \cdot m}{r^{2}}[/tex]
b.
[tex]F =6,378 \times 10^{-11} \times \dfrac{5.97 \times 10^{24} \times 1,300}{6,578^{2}}[/tex]
c.
[tex]F =6,378 \times 10^{-11} \times \dfrac{5.97 \times 10^{24} \times 1,300}{6,578^{2}} = \dfrac{9.519165 \times 10^{18}}{832117} \approx 1.144 \times 10^{13}[/tex]
d. 1.144 × 10¹³ N
Explanation:
The universal law of gravitation is presented as follows;
[tex]F =G \cdot \dfrac{M \cdot m}{r^{2}}[/tex]
The given mass of the scientific satellite, m = 1,300 kg
The height of the orbit of the satellite, r = 200 km above the Earth's surface
The length of the radius of the Earth, R = 6378 km
The mass of the Earth = 5.97 × 10²⁴ kg
a. The formula for the universal law of gravitation is presented as follows;
[tex]F =G \cdot \dfrac{M \cdot m}{r^{2}}[/tex]
Where;
M = The mass of the Earth = 5.97 × 10²⁴ kg
m = The mass of the satellite = 1,300 kg
r = The distance between the Earth and the satellite = R + r = 6,378 km + 200 km = 6,578 km
G = The Gravitational constant = 6.67430 × 10⁻¹¹ N·m²/kg²
b. Plugging in the values from the problem into the formula gives;
[tex]F =6,378 \times 10^{-11} \times \dfrac{5.97 \times 10^{24} \times 1,300}{6,578^{2}}[/tex]
c. Solving gives;
[tex]F =6,378 \times 10^{-11} \times \dfrac{5.97 \times 10^{24} \times 1,300}{6,578^{2}} = \dfrac{9.519165 \times 10^{18}}{832117} \approx 1.144 \times 10^{13}[/tex]
The force acting between the Earth and the satellite, F ≈ 1.144 × 10¹³ N
d. 1.144 × 10¹³ N
What is kinetic and potential energy?
Answer:
the energy produced in a body due to its motion is kinetic energy.
energy produced in a body due to its position is potential energy.
Explanation:
kinetic energy is the energy possessed by a body in motion
Potential energy is the energy possessed by a body by virtue of its position with respect to a reference level
What form of energy is needed to make photosynthesis happen?
A. Proton energy
B. Chemical energ
C. Electron energy
D. Solar energy
Answer:
Photosynthesis converts solar energy into chemical energy.
your answer is solar energy
hope it helps
A cell has an emf of 1.5 V and an internal resistance of 0.65 Q.
The cell is connected to a resistor R.
[0[8].[4] State what is meant by an emf of 1.5 V.
[2 marks]
I
[0] 8]-[2] The current in the circuit is 0.31 A.
Show that the total power output of the cell is approximately 0.47 W.
[1 mark]
[o[s).[3] Calcutate the energy dissipated per second in resistor R.
[2 marks]
energy dissipated per second = Ist
[o[si.[4] The cell stores 14 kJ of energy when it is fully charged. The cell's emf and internal resistance are constant as the cell f discharged.
Calculate the maximum time during which the fully-charged cell can deliver energy to
resistor R.
[2 marks)
maximum time = 5
Answer:
14000 J / 0.40 J/s = 35 000 s or about 9.75 hrs
HELPPP ILL GIVE BRAINLIST
Answer:
1= Kidneys
2= Ureters
3=Bladders
4=Urethra
Explanation:
Functions of kidney: Regulations of water balances, excretions of nitrogenous wastes(urea)
Functions of Liver: Detoxifications, protein synthesis
Functions of Skin: Temperature regulations, Metabolic functions, Excretion
Functions of lungs: Respiration, Water balance regulations
Tip: If you want faster and correct answers you should label your questions under the correct subject.
Una prenda de 320gramos de ropa gira en el interior de una lavadora si dicha lavadora tiene 40 cm y gira con una frecuencia de 4 hz halla el periodo la velocidad angular la fuerza con la que gira la prenda y la velocidad lineal de la lavadora
Answer:
Período del tambor: [tex]T = 0.25\,s[/tex], fuerza sobre la prenda: [tex]F \approx 80.852\,N[/tex], velocidad lineal del tambor: [tex]v \approx 10.053\,\frac{m}{s}[/tex], velocidad angular del tambor: [tex]\omega \approx 25.133\,\frac{rad}{s}[/tex].
Explanation:
La expresión tiene un error por omisión, su forma correcta queda descrita a continuación:
"Una prenda de 320 gramos de ropa gira en el interior de una lavadora si dicha lavadora tiene un radio de 40 centímetros y gira con una frecuencia de 4 hertz. Halle a) el período, b) la velocidad angular, c) la fuerza con la que gira la prenda y d) la velocidad lineal de la lavadora."
El tambor gira a velocidad angular constante ([tex]\omega[/tex]), en radianes por segundo, lo cual significa que la prenda experimenta una aceleración centrífuga ([tex]a[/tex]), en metros por segundo al cuadrado. En primer lugar, calculamos el período de rotación del tambor ([tex]T[/tex]), en segundos:
[tex]T = \frac{1}{f}[/tex] (1)
Donde [tex]f[/tex] es la frecuencia, en hertz.
([tex]f = 4\,hz[/tex])
[tex]T = \frac{1}{4\,hz}[/tex]
[tex]T = 0.25\,s[/tex]
Ahora determinamos la fuerza aplicada sobre la prenda ([tex]F[/tex]), en newtons:
[tex]F = m\cdot a[/tex] (2)
[tex]F = \frac{4\pi^{2}\cdot m \cdot r}{T^{2}}[/tex] (2b)
Donde:
[tex]m[/tex] - Masa de la prenda, en kilogramos.
[tex]r[/tex] - Radio interior del tambor, en metros.
([tex]m = 0.32\,kg[/tex], [tex]r = 0.4\,m[/tex], [tex]T = 0.25\,s[/tex])
[tex]F = \frac{4\pi^{2}\cdot (0.32\,kg)\cdot (0.4\,m)}{(0.25\,s)^{2}}[/tex]
[tex]F \approx 80.852\,N[/tex]
La velocidad lineal de la lavadora es:
[tex]v = \frac{2\pi\cdot r}{T}[/tex] (3)
([tex]r = 0.4\,m[/tex], [tex]T = 0.25\,s[/tex])
[tex]v = \frac{2\pi\cdot (0.4\,m)}{0.25\,s}[/tex]
[tex]v \approx 10.053\,\frac{m}{s}[/tex]
Y la velocidad angular del tambor de la lavadora:
[tex]\omega = \frac{2\pi}{T}[/tex]
([tex]T = 0.25\,s[/tex])
[tex]\omega = \frac{2\pi}{0.25\,s}[/tex]
[tex]\omega \approx 25.133\,\frac{rad}{s}[/tex]
If the amplitude of a sound wave is increased by a factor of four,how does the energy carry by the sound wave in each time interval change?
Answer:
The energy will be increased by a factor 16
Explanation:
Mathematically, we have it that the energy carried by the sound wave is directly proportional to the square of the amplitude
So we have it that;
E = k * A^2
where E is the wave energy
K is the constant value
A is the amplitude value
So;
If E1 = k * (A1)^2
E2 = k * (A2)^2
But A2 = 4A1
E2 = k * (4A1)^2
E2 = k * 16(A1)^2
Divide E2 by E1
E2/E1 = k/k * 16(A1)^2/(A1)^2
E2/E1 = 16
E2 = 16 * E1
so simply, the energy will be increased by a factor of 16
Why is a person not a good blackbody radiator?
O A. A person emits only visible light.
OB. A person emits only infrared radiation.
O C. A person absorbs most of the light that hits him or her.
O D. A person reflects little of the light that hits him or her.
Answer:
O C. A person absorbs most of the light that hits him or her.
Explanation:
Answer:
Option D hope it's helpful mark me as brainlistPlease help!!!!! I will give brainliest. Describe four examples of acceleration you see during your day. Choose an object that is slowing down, one that is speeding up, one that is moving at a constant speed but changing direction, and one that is moving at a constant velocity with zero acceleration.
When the brake is applied to the car and comes to rest after some time is an example of an object that is slowing down.
What is acceleration?The rate of change of velocity with respect to time is known as acceleration. According to Newton's second law, the eventual effect of all forces applied to a body is its acceleration.
1. When the brake is applied to the body and comes to rest after some time is an example of an object that is slowing down.
2. When a person accelerates the car and the velocity is increasing is an example of speeding up.
3. An object moves in a circular motion moving at a constant speed but changing direction,
4. Acceleration is the rate of change of velocity. If the change in the velocity is constant the acceleration is zero is an example of moving at a constant velocity with zero acceleration.
To learn more about acceleration, refer to the link;
https://brainly.com/question/2437624
#SPJ1
A young student drops a stone off the side of a cliff that is 41 meters high. How long does it take the stone to hit the ground below?
A)
2.89 s
B)
8.36 s
C)
3.20 s
D)
2.04 s
Which of the following could be used to create an open circuit?
The dependent variable measured was the ______
a. fan speed
b. mass
c. acceleration
Answer:
a
Explanation:
Fan speed is the answer
when a car drives in a circle there must be ?
no net force axting on it
Answer:
I think none of above
Explanation:
hioe it's right answer
Which statement describes how chemical formulas, such as H20, represent compounds?
Answer:
They show the elements that make up a compound.
They show the three-dimensional shape of a molecule.
They show the types of atoms that make up a molecule.
They show the number of each type of atom in a molecule.
Explanation:
❣️(◍Jess bregoli◍)❣️#keep learning!!
What is an example of a series circuit
Answer:
Explanation
The most famous and common example is Christmas tree lights. You can't tell easily by looking at them whether they are in series or parallel. But you sure know the difference when one of them burns out. When that happens, the whole string goes dead. No matter what you do (other than find out which bulb burned out) will not fix the problem.
Another example is anything that is temperature controlled. For example a furnace is controlled by a thermostat. When the room temperature reaches a certain point, the thermostat is constructed in a certain way so that it forms an open circuit and no current can flow through it. The furnace motor turns off and the furnace stops pumping hot air into a room.
A partially inflated balloon is faded over the open end of a glass beaker that contains water the beaker is placed in an ice bath which cause the water and causes the balloon to the flea what are the correct designs for the heat and work changes to the beaker and balloon system
Answer:
a
Explanation:
Help me please Ima give brainiest
Answer: vinegar
A heterogeneous mixture is a mixture in which the composition is not uniform throughout the mixture. ... A heterogeneous mixture consists of two or more phases. When oil and water are combined, they do not mix evenly, but instead, form two separate layers. Each of the layers is called a phase.
Hope it helps...
