Answer:
The resistance of a thin wire is greater than the resistance of a thick wire because a thin wire has fewer electrons to carry the current. The relationship between resistance and the area of the cross section of a wire is inversely proportional .
The best way to think about this is:
A thick/wide road, with many lanes, can carry more cars than a thin/narrow road, with only one or two lanes.
The fluid inside the hydraulic jack has a pressure of 30,000 Pa. If the surface of
the piston that is used to lift an object is 0.1 m’in area, how much weight can
the jack lift?
Explanation:
p = F /A
F = P×A
F = 30,000 Pa / 0.1 m²
F = 300,000 N
What is not one of the main uses of springs?
A. Bike suspension
B. The seasons
C. Clock making
D. Car suspension
Quick answer
Answer:
b. the seasons
Explanation:
what weight is recorded by a scale when it is placed inside a lift which is in free fall? Enplain.
Answer:
Explanation:
There is no pressure of your feet on the scales, and no pressure of the floor on the scales, so the scales will read zero*. Hence, your weight, in a freely falling lift is zero
Define measurement with 10 points
Answer:
the process of comparing unknown quantities with known standards quantities are known as measurement
pete walks at a rate of 4.0 miles per hour for 30 minutes. How far did he walk?
differniate between Magnetic force and electrostatic force
Answer:
magnetic force:
i) It is exerted by a magnet.
ii)Magnetic forces are always normal to the direction of the velocity of the charge it acts upon.
Electrostatic force
i) It is exerted by electrically charged body.
ii)Electric force are independent of the direction the charge moves in.
✌✌✌✌
What kind of circuit is the one shown below?
A. Series
B. Parallel
C. Open
D. Combination
That's a parallel circuit. (B)
When current from Point-A reaches the 3-way intersection just to the right of Point-B, it has to make a choice: Either turn left, go through B, and light the lower bulb, or go straight and light the upper bulb.
A circuit that has any "decision" points in it is a parallel circuit. What happens in the real world is: The current splits up. Some of the current that reaches the intersection turns left toward Point-B, and the rest of it goes straight up.
A series circuit is one in which there's only one possible path all the way around. There are no intersections of more than 2 roads, and no electron ever has to decide which way to flow.
An open circuit is one in which there's a break somewhere along the line and electrons can't jump across it. It's like a railroad where a big piece is cut out of the track somewhere. So no trains can travel on that route, and there's no current flowing anywhere in the circuit.
I'm not so sure about a "combination" circuit. I guess you could give that name to a complicated circuit that has some series parts and some parallel-parts. Personally, I'd call that a "series-parallel" circuit. But it really doesn't matter right now. Whatever the word means, the circuit in the picture is definitely not a "combination" circuit.
Answer:
B. Parallel Circuits
Explanation:
A parallel circuit is constructed by connecting the terminals of all the individual load devices so that the same value of voltage appears across each component. In a parallel circuit, charge divides up into separate branches such that there can be more current in one branch than there is in another.
hope i helped
List two factors that compression force depends on
The magnitude (size or numerical value) and the direction.
Hope this helps!!! :)
mercury is commonly used in thermometer give reasons
Answer:
hi
BECAUSE MERCURY IS USED BECAUSE IT is the only liquid available in room temperatureExplanation:
pls mark as a BRAINLIST
By how many times will the kinetic energy of a body increase if its speed is tripled? Show by calculation .
Answer:
9 lần
Explanation:
Answer:
Kinetic energy (k.e) varies directly as v² from the formula
K.E=(mv²/2)
if v=3 then K.e =v²=(3)²=9
Does water exist on Mars? Explain your answer. Why didn't Jupiter become a star during the early.
Answer:
yes water was discovered in mars
is there any machine that is 100% efficient? why?why not
Answer:
No, it's not there.
Explanation:
For a machine to be 100% efficient, it has to be with an output which is equal to its input. But machines have an out put less than an input, hence efficiency below 100%.
Robin fired a bullet of mass 100 gm from a gun of mass 5 kg. The bullet leaves the gun with a speed of 400 m/s. After penetrating 4 cm of a plank of 10 cm, the bullet loses one third of its initial velocity.
a. Calculate the backward velocity of the gun?
b. Can the bullet penetrate the plank of the wood completely? Explain mathematically.
please help
(a) The recoil or backward velocity of the gun is 8 m/s.
(b) The bullet cannot penetrate the plank of the wood completely.
The given parameters include;
mass of the bullet, m₁ = 100 g = 0.1 kgmass of the gun, m₂ = 5 kginitial velocity of the bullet, u₁ = 400 m/sthickness of the plank, x = 10 cm(a) The backward or recoil velocity of the gun is calculated by applying the principle of conservation of linear momentum.
let the backward or recoil velocity of the gun = u₂m₁u₁ + m₂u₂ = 0
m₂u₂ = -m₁u₁
[tex]u_2 = -\frac{m_1u_1}{m_2} \\\\u_2 = - \frac{0.1 \times 400}{5} \\\\u_2 = -8 \ m/s[/tex]
Thus, the recoil or backward velocity of the gun is 8 m/s.
(b) determine if the bullet can penetrate the plank of the wood completely
the bullet traveled 4 cm and lost ¹/₃ of u₁the remaining distance to completely penetrate the plank = 6 cmthe final velocity of the bullet at 4 cm, v = 400 - ¹/₃ x 400 m/s = 266.67 m/sthe acceleration of the bullet is calculated as;
v² = u₁² + 2as
2as = v² - u²
[tex]a = \frac{v^2 -u_1^2}{2s} \\\\a = \frac{(266.67)^2 -(400)^2}{2\times 0.04} = -1.111 \times 10^6 \ m/s^2[/tex]
Finally, determine the distance traveled by the bullet when it comes to a complete stop, that is the final velocity = 0
[tex]v_f^2 = v^2 + 2ad\\\\2ad = v_f^2 - v^2\\\\d = \frac{v_f^2 - v^2}{2a} \\\\d = \frac{(0) - (266.67)^2}{2(-1.111\times 10^6)} \\\\d = 0.032 \ m[/tex]
d = 3.2 cm
The total distance traveled by the bullet inside the plank = 4 cm + 3.2 cm = 7.2 cm
Therefore, the bullet cannot penetrate the plank completely.
To learn more about linear momentum visit: https://brainly.com/question/15869303
the force between the earth and the body which is at a distance r from the center of the earth is F. What must be this distance for the force to be doubled.
Answer:
Explanation:
The gravitational force between the earth and another body is F = -GM_em/r^2 r where G = 6.67 times 10^-11 Nm^2/kg^2 is the gravitational constant, M_e = 5.97 times 10^24 kg is the mass of the earth, m is the mass of the other body, and r is the position vector of the second body with respect to the centre of the earth.
You plan to pass alpha particles through a field that contains a consistent type of particle. Which configuration will result in the largest deflection of alpha particles? (1 point)
low-energy alpha particles passing through a field of low mass-number-particles
low-energy alpha particles passing through a field of high mass-number-particles
high-energy alpha particles passing through a field of high mass-number-particles
high-energy alpha particles passing through a field of low mass-number-particles
Answer:
low-energy alpha particles passing through a field of high mass-number-particles
Answer:
low-energy alpha particles passing through a field of high mass-number-particles
Explanation:
Saul is testing an installation and discovers a short circuit what’s causing this
A.high current
B.high voltage
C.low resistance
D.low voltage
Answer:
im pretty sure that it's (A.) High current
Explanation:
pf
not 100% sure, tho
A bike travels at 3.0 m/s, and then accelerates to a speed of
8.5 m/s in a time of 2.5 seconds. The average acceleration of
the bike is
m/s2
The average acceleration of the bike is 2.2 m/s²
What is average acceleration?Acceleration, rate at which velocity changes with time, in terms of both speed and direction.
A point or an object moving in a straight line is accelerated if it speeds up or slows down.
According to the question,
Given, initial velocity, u=3.0m/s and final velocity v=8.5 m/s
Time = 2.5 seconds
If a be the acceleration.
a = [tex]\frac{v-u}{t}[/tex]
a = [tex]\frac{8.5 - 3.0}{2.5s}[/tex]
⟹ a=2.2 m/s²
So, The average acceleration of the bike is 2.2 m/s²
Learn more about average acceleration here:
https://brainly.com/question/2303856
#SPJ2
Which of the following is a vector quantity? i. Force ii. Velocity iii. Acceleration iv. All of these 5771
Option ( iv ) is the correct answer.
☛ DefinitionA vector quantity the physical quantity that has both direction as well as magnitude.
The mass of earth 6*10^24kg and radius is 400kg Now find the value of acceleration due to gravity when a object is 3600km from the earth surface
difference between uniform motion and non uniform motion
Answer:
Uniform motion is a type of motion that is characterized as the motion of an object wherein the object moves in a straight line and its velocity remains unchanged along that line, regardless of the duration of time, as it occupies equal distances at equal time interval and Non-uniform motion is described as the motion of an object wherein the object moves at different speeds and does not cover the same distance at equal time intervals, regardless of the duration of the time interval.
Answer:
hope it's help you
Explanation:
In Uniform motion, the movement of a body is along the straight line with constant speed. In non uniform motion, the movement of a body is along the straight line with variable speed. In uniform motion, the body covers equal distance in an equal interval of time.
The direction of applied force has to be .............. to the distance in order to say work is done
Answer:
Parallel
Explanation:
The work done is defined as the force applied on an object and the displacement in the position of the object in the direction of force.
W = F s cos A
where, F is the force, s is the displacement and A is the angle between force and displacement.
When the angle between the force and the displacement is 90 degree, the work done is zero.
To get the maximum work the angle between the force and the displacement is 0 degree.
So, to get the work done by the force the angle between the force and displacement is 0 degree that means the force and displacement is parallel to each other.
9. Which of the following is NOT a recommendation to help you succeed in this course?
Consistently and actively work in the course on a daily basis.
Wait until the end of the semester to complete all work.
Complete all assignments in a timely manner.
Contact your instructor if you have questions.
Answer:
Wait until the end of the semester to complete all work.
Explanation:
this is the obvious answer.
please mark me brainliest
Answer:
Wait until the end of the semester to complete all work
The plane of a5cm*8cm rectangular loop of wire is parallel to a 0.19T magnetic field the loop carries a current of 6.2 A. What torque acts on aloop? What is the magnetic moment of the loop?
Answer:
Torque; τ = 4.712 × 10^(-3) J
Magnetic moment; M = 0.0248 J/T
Explanation:
Torque is gotten from the formula;
τ = BIA
Where;
B is magnetic field
I is current
A is area
We are given;
B = 0.19T
I = 6.2A
Rectangle dimensions = 5cm by 8cm = 0.05m by 0.08m
Thus;
Area; A = 0.05m × 0.08m = 0.004 m²
Thus;
τ = 0.19 × 6.2 × 0.004
τ = 4.712 × 10^(-3) J
Formula for the magnetic moment is given by;
M = IA
M = 6.2 × 0.004
M = 0.0248 J/T
Please help me , I also have to show work on paper
Answer:
Choose B
Explanation:
Hope Can I help you
during a journey, a car travels at 40 km in 2.5 hours, next 62 km in 3 hours, then took a break for 30 minutes, again travelled the last 120 km in 3.2 hours. calculate the average speed of the car during the journey.
20. A semiconductor is a
A) crystalline solid that conducts current under any condition
B) metallic solid that conducts current under any condition
C) metallic solid that conducts current under certain conditions
D) crystalline solid that conducts current under certain conditions
Answer:
D) crystalline solid that conducts current under certain conditions
Explanation:
A semiconductor is any crystalline solid material whose electrical conductivity is intermediary between that of insulators and conductors. That is, a semiconductor does not conduct like a conductor but does more than an insulator.
Based on this, a semiconductor is said to only conduct electricity under certain conditions as opposed to conductors that do so under any condition. Example of semiconductors are silicon, carbon, antimony, arsenic etc.
what give negative acceleration ?
Answer:
But negative acceleration means that the rate of change of velocity is negative or velocity decreases. Example: (1) When we apply brakes in a moving car, then negative acceleration acts on it and the car stops. (2) When we throw a ball upwards, then also negative acceleration acts on it.
Explanation:
If it helps you mark me as a brainleast
MATHEMATICALLY A NEGATIVE ACCELERATION MEANS YOU WILL SUBTRACT FROM THE CURRENT VALUE OF THE VELOCITY.
define 1 second time
Answer:
define 1 second time
One second is the time that elapses during 9,192,631,770 (9.192631770 x 10 9 ) cycles of the radiation produced by the transition between two levels of the cesium 133 atom. ... One second is equal to 1/86,400 of a mean solar day.
Answer:
One part of 86400 part of a day is called one second time.
✌✌✌✌
Why does a ship float on water when it weighs about 100tones and why a stone of less than a kg sinks
Answer with Explanation:
Let me answer this in a simple way, since the density of stone is greater than that of water, the stone sinks as the weight of the stone is greater than the weight of water displaced by it. But the ship is designed in such a way that the relative density of the ship always becomes less than that of water. Therefore, the weight of the water displaced becomes equal to the total weight of the ship and thus it floats.
There are many other ways to explain this but this should give you the general idea.
Our Moon a. was a separate small planet before it was captured by the Earth's gravity. b. spun off the fast-spinning Earth during the early formation of the Solar System. c. coalesced from gas and dust in its current place next to the Earth. d. was formed by the collision of the Earth with a Mars-sized protoplanet.
Answer:
d. was formed by the collision of the Earth with a Mars-sized protoplanet.
According to the The giant-impact hypothesis the Moon was formed from the debris of a collision between the Earth and a Mars-sized protoplanet.