Answer:
The hot temperature is 157.5 K
The cold temperature is 48.8 K
Explanation:
Step 1: Data given
The working substance of a certain Carnot engine is 1.50 mol of an ideal monatomic gas.
The volume increases by a factor of 5.7
The work output of the engine is 940 J in each cycle.
During the isothermal expansion portion of this engine's cycle, the volume of the gas doubles. This means V2 = 2*V1 (and V4 = 2*V3)
Step 2:For a carnot engine:
V2/V1 = V4/V3
Work = nR((T1)ln(V2/V1) - (T2)ln(V4/V3))
⇒with Work = the work done in the cycle = 940J
⇒with n = the number of moles = 1.50 moles
⇒with R = the gas constant = 8.314 J/mol*K
⇒with T1 = the hot temperature
⇒With T2⇒ the cold temperature
where R = 8.31 J/mol K Gas Constant
940J = 1.5moles * 8.314 J/mol*K * (T1*ln(2) - T2*ln(2)))
940 = 1.5 * 8.314 ln(2) * (T1-T2)
(T1-T2) = 940 / (1.5*8.314*ln(2))
(T1-T2) = 108.7K
For the reversible adiabatic expansion: T2 = T1*(V1/V2)^(R/Cv). Where V2/V1 = 5.7 (Because during the adiabatic expansion the volume increases by a factor of 5.7)
For a monatomic ideal gas, Cv = 3/2R
When we combine both, we'll have:
T2 = T1*(1/5.7)^(R/3/2R)
T2 = T1*(1/5.7)^(2/3)
T2= T1 * 0.31
Since we know that (T1-T2) = 108.7K
we have:
T1 - 0.31T1= 108.7K
0.69T1 = 108.7K
T1 = 157.5K
T2 = 157.5*0.31 = 48.8K
A 12.5-m fire truck ladder is leaning against a wall. Find the distance d the ladder goes up the wall (above the fire truck) if the ladder makes an angle of with the horizontal
Complete Question
A 12.5-m fire truck ladder is leaning against a wall. Find the distance d the ladder goes up the wall (above the fire truck) if the ladder makes an angle of
40° 16' with the horizontal.
Answer:
[tex]d=8.01m[/tex]
Explanation:
From the question we are told that:
Length of ladder [tex]l=12.5m[/tex]
Angle [tex]\theta=40° 16'=20.26 \textdegree[/tex]
Generally the Trigonometric equation for distance d it goes up the wall is mathematically given by
[tex]d=l sin \theta[/tex]
[tex]d=12.5 sin 40.26[/tex]
[tex]d=8.01m[/tex]
What are stepdown transformers used for
Answer:
Step down transformers are used in power adaptors and rectifiers to efficiently decrease the voltage. They are also used in electronic SMPS.
Explanation:
pls mark me as brainlist
Thanks a lot
Water is falling on the blades of a turbine at a rate of 100 kg/s from a certain spring. If the height of spring be 100m, then the power transferred to the turbine will be: a) 100 KW b) 10 KW c) 1 KW d) 100 W
Answer:
Natae Si Jordan Kaya Sya Napaihe
Explanation:
haha
There are two beakers of water on the table. We can compare the average kinetic energy of the water molecules in the two beakers by measuring their
A temperatures.
B volumes.
C densities.
D masses.
Answer: masses
Explanation:
Trust me
When an apple falls towards the earth,the earth moves up to meet the apple. Is this true?If yes, why is the earth's motion not noticeable?
Answer:
Yes, when an apple falls towards the earth, the apple gets accelerated and comes down due to the gravitational force of attraction used by the earth. The apple also exerts an equal and opposite force on the earth but the earth does not move because the mass of the apple is very small, due to which the gravitational force produces a large acceleration in it (a = F/m) but the mass of the earth is very large, the same gravitational force produces very small acceleration in the earth and we don't see the earth rising towards the apple.
What is significant about the primary colors of pigments?
They can be mixed together to make almost any other color.
Any two primary colors of pigments combine to make white pigment.
Each primary color of pigment absorbs all other colors.
Any two primary colors of pigments combine to make black pigment.
Answer:
They can be mixed together to make almost any other color.
Explanation:
All the three primary colors can mix to form white color.
Blue and red mix to form a black color.
PLEASE HELP ME WITH THIS ONE QUESTION
The half-life of Barium-139 is 4.96 x 10^3 seconds. A sample contains 3.21 x 10^17 nuclei. How much of the sample is left after 1.98 x 10^4 seconds?
[tex]A=2.01×10^{16}\:\text{nuclei}[/tex]
Explanation:
Given:
[tex]\lambda = 4.96×10^3 s[/tex]
[tex]A_0 = 3.21x10^{17}[/tex] nuclei
t = 1.98×10^4 s
[tex]A=A_02^{-\frac{t}{\lambda}}[/tex]
[tex]A=(3.21×10^{17}\:\text{nuclei}) \left(2^{-\frac{1.98×10^4}{4.96×10^3}} \right)[/tex]
[tex]\:\:\:\:\:\:\:=2.01×10^{16}\:\text{nuclei}[/tex]
IS ANYONE THERE..??!
Answer:
hmmmmmmmmmmmmmmmmmmmmmmmm y
A hot air balloon is a sphere of volume 2210 m3. The density of the hot air inside is 1.13 kg/m3, while the air outside has a density of 1.29 kg/m3. The balloon itself has a mass of 240 kg. What is the TOTAL NET force acting on the balloon?
[?]N
The total net force acting on the balloon will be 24498 Newtons
Given that
Volume of the balloon = 2210 cubic meter
Density of the air inside the balloon = 1.13 kg/m3
What will be the net force exerted on the balloon ?Here force on the balloon will be equal to the weight of the air displaced by balloon
[tex]F= mass of air displaced\times gravity[/tex]
[tex]F= Density \times volume \times gravity[/tex]
[tex]F=1.13 \times 2210 \times 9.81[/tex]
[tex]F=24498 N[/tex]
The total net force acting on the balloon will be 24498 Newtons
To know more about buoyancy force follow
https://brainly.com/question/117714
what is Friction
short note on friction
Answer:
Explanation:
Friction can be defined as a force that resists the relative motion of two objects when there surface comes in contact. Thus, it prevents two surface from easily sliding over or slipping across one another. Also, friction usually reduces the efficiency and mechanical advantage of machines but can be reduced through lubrication.
Generally, there are four (4) main types of friction and these includes;
I. Static friction.
II. Rolling friction.
III. Sliding friction.
IV. Fluid friction.
Explain the following observations:
a) A balloon filled with hydrogen gas floats in air;
B) A ship made of steel floats on water.
Answer and Explanation:
a. An oxygen-filled balloon is not able to float in the air, because the oxygen inside the balloon is of the same density, that is, the same "weight" as the oxygen outside the balloon and present in the atmosphere. The balloon can only float if the gas inside it is less dense than atmospheric oxygen. Helium gas is less dense than atmospheric gas, so if a balloon is filled with helium gas, that balloon will be able to float because of the difference in density.
b. The ship is able to float in the water because its steel construction is hollow and full of air. This makes the average density of this ship less than the density of water, which makes the ship lighter than water and for this reason, this ship is able to float. In addition, the ship is partially immersed, allowing the weight of the ship on the water to counteract the buoyant force that the water promotes on the ship. Weight and buoyant are two opposing forces that keep the ship afloat.
An unwary football player collides with a padded goalpost while running at a velocity of 7.50 m/s and comes to a full stop after compressing the padding and his body 0.350 m. (a) What is his deceleration
Answer:
a= -80.357 m/s
Explanation:
use the formula
vf^2=vi^2+2a(xf-xi)
Plug in givens
0=(7.50)^2+2a(0.350m)
solve for acceleration
a= -80.357 m/s
High-speed stroboscopic photographs show that the head of a -g golf club is traveling at m/s just before it strikes a -g golf ball at rest on a tee. After the collision, the club head travels (in the same direction) at m/s. Find the speed of the golf ball just after impact.
The question is incomplete. The complete question is :
High-speed stroboscopic photographs show that the head of a 200 g golf club is traveling at 60 m/s just before it strikes a 50 g golf ball at rest on a tee. After the collision, the club head travels (in the same direction) at 40 m/s. Find the speed of the golf ball just after impact.
Solution :
We know that momentum = mass x velocity
The momentum of the golf club before impact = 0.200 x 60
= 12 kg m/s
The momentum of the ball before impact is zero. So the total momentum before he impact is 12 kg m/s. Therefore, due to the conservation of momentum of the two bodies after the impact is 12 kg m/s.
Now the momentum of the club after the impact is = 0.2 x 40
= 8 kg m/s
Therefore the momentum of the ball is = 12 - 8
= 4 kg m/s
We know momentum of the ball, p = mass x velocity
4 = 0.050 x velocity
∴ Velocity = [tex]$\frac{4}{0.050}$[/tex]
= 80 m/s
Hence the speed of the golf ball after the impact is 80 m/s.
What is (a) the x component and (b) the y component of the net electric field at the square's center
Answer:
What is (a) the x component and (b) the y component of the net electric field at the square's center
write down the following units in the ascending of their value A) mm nm cm um B) 1m 1cm 1km 1mm. convert the following units into SI without changing their values? A)3500g B)2.5km C)2h
Answer:
A) nm, um, mm, cm
B) 1mm, 1cm, 1m, 1km
A) 3500g, B) 2500m, C) 7200 seconds
What word chemical equation describes this chemical reaction?
Answer : sodium + chlorine → sodium chloride
Typhoon signal number 2 is raised. What is the speed of the expected typhoon?
the simple answer is from 61kmph to 120kmph
Explanation:
no explanation is needed
Every object around you is attracted to you. In fact, every object in the galaxy is attracted to every other object in the galaxy.
a. True
b. False
Answer:
True
Explanation:
With the gravitational pull that our planets have, we are able to remain in orbit. This demonstrates how every object in the galaxy is attracted to every other object. Every object in the universe that has mass exerts a gravitational pull on every other mass. We as humans do it too, but since our force isn't strong, we don't have much of an effect. I hope this helped and please don't hesitate to reach out with more questions!
Betelgeuse (in Orion) has a parallax of 0.00451 + 0.00080 arcsec,as measured by the Hipparcos satellite. What is the distance to Betelgeuse, and what is the uncertainty in that measurement?
We have that the distance to Betelgeuse, and the uncertainty in that measurement is
[tex]d=(221.7\pm39.33)pc[/tex]Uncertainty U = 0.00080
From the Question we are told that
Betelgeuse (in Orion) has a parallax of 0.00451 + 0.00080
Generally
[tex]Distance\ in\ parsecs =\frac{ 1}{(parallax\ measured\ in\ arcseconds}[/tex]
Where
Parallax [tex]P =0.00451[/tex]
Uncertainty [tex]U = 0.00080[/tex]
Generally the equation for the distance is mathematically given as
[tex]d=(\frac{1}{P}pc\pm(\frac{U}{P}*100\%))[/tex]
Therefore
[tex]d=(\frac{1}{0.00451}pc\pm(\frac{0.00080}{0.00451}*100\%))[/tex]
[tex]d=(221.7\pm39.33)pc[/tex]
For more information on this visit
https://brainly.com/question/12319416?referrer=searchResults
A particle of mass 1.2 mg is projected vertically upward from the ground with a velocity of 1.62 x 10 cm/h. Use the above information to answer the following four questions: 7. The kinetic energy of the particle at time t = 0 s is A. 1.215 x 10-3 J B. 2.430 J C. 1215 J D. 9.72 x 106 J E. OJ (2)
Answer:
K = 0 J
Explanation:
Given that,
The mass of the particle, m = 1.2 mg
The speed of the particle, [tex]v=1.62\times 10\ cm/h[/tex]
We need to find the kinetic energy of the particle at time t = 0 s.
At t = 0 s, the particle is at rest, v = 0
So,
[tex]K=\dfrac{1}{2}mv^2[/tex]
If v = 0,
[tex]K=0\ J[/tex]
So, the kinetic energy of the particle at time t = 0 s is 0 J.
A block of mass M is connected by a string and pulley to a hanging mass m. The coefficient of kinetic friction between block M and the table is 0.2, and also, M = 20 kg, m = 10 kg. How far will block m drop in the first seconds after the system is released?
How long will block M move during above time?
At the time, calculate the velocity of block M
Find out the deceleration of the block M, if the connected string is
removal by cutting after the first second. Then, calculate the time
taken to contact block M and pulley.
Answer:
a) y = 0.98 t², t=1s y= 0.98 m,
b) he two blocks must move the same distance
c) v = 1.96 m / s, d) a = -1.96 m / s², e) x = 0.98 m
Explanation:
For this exercise we can use Newton's second law
Big Block
Y axis
N-W = 0
N = M g
X axis
T- fr = Ma
the friction force has the expression
fr = μ N
fr = μ Mg
small block
w- T = m a
we write the system of equations
T - fr = M a
mg - T = m a
we add and resolved
mg- μ Mg = (M + m) a
a = [tex]g \ \frac{m - \mu M}{m+M}[/tex]
a = [tex]9.8 \ \frac{10- 0.2 \ 20}{ 10 \ +\ 20}[/tex]
a = 9.8 (6/30)
a = 1.96 m / s²
a) now we can use the kinematic relations
y = v₀ t + ½ a t²
the blocks come out of rest so their initial velocity is zero
y = ½ a t²
y = ½ 1.96 t²
y = 0.98 t²
for t = 1s y = 0.98 m
t = 2s y = 1.96 m
b) Time is a scale that is the same for the entire system, the question should be oriented to how far the big block will move.
As the curda is in tension the two blocks must move the same distance
c) the velocity of the block M
v = vo + a t
v = 0 + 1.96 t
for t = 1 s v = 1.96 m / s
t = 2 s v = 3.92 m / s
d) the deceleration if the chain is cut
when removing the chain the tension becomes zero
-fr = M a
- μ M g = M a
a = - μ g
a = - 0.2 9.8
a = -1.96 m / s²
e) the distance to stop the block is
v² = vo² - 2 a x
0 = vo² - 2a x
x = vo² / 2a
x = 1.96² / 2 1.96
x = 0.98 m
the time to travel this distance is
v = vo - a t
t = vo / a
t = 1.96 /1.96
t = 1 s
12) If, after viewing a specimen at low power, you switch to high-dry power and, after using fine focus, cannot find the specimen, what things could you do to help yourself (before calling me over to assist you?)
Answer:
See the answer below
Explanation:
After seeing an object on a slide at the low-power objective of the microscope and it disappears on changing to high power, the following can be done to resolve the problem
1. Drop a few drops of immersion oil on the slide and view again under high the power objective.
2. If the object is still not visible after the action above, return the microscope to the low-power objective and make sure the object is refocused and centered. Then carefully change back to the high power objective and use the fine adjustment to bring it into focus.
At which point is the kinetic energy of the pendulum the greatest?
C
A
D
B
Answer:
Point C
Explanation:
Greatest Kinetic Energy means lowest potential energy since energy is conserved. Lowest potential energy means lowest height which is at Point C.
A 64-ka base runner begins his slide into second base when he is moving at a speed of 3.2 m/s. The coefficient of friction between his clothes and Earth is 0.70. He slides so that his speed is zero just as he reaches the base.
Required:
a. How much mechanical energy is tout due to friction acting on the runner?
b, How far does he slide?
Answer:
Explanation:
From the given information:
mass = 64 kg
speed = 3.2 m/s
coefficient of friction [tex]\mu =[/tex] 0.70
The mechanical energy touted relates to the loss of energy in the system as a result of friction and this can be computed as:
[tex]W = \Delta K.E[/tex]
[tex]\implies \dfrac{1}{2}m(v^2 -u^2)[/tex]
[tex]= \dfrac{1}{2}(64.0 \kg) (0 - (3.2 \ m/s^2))[/tex]
Thus, the mechanical energy touted = 327.68 J
According to the formula used in calculating the frictional force
[tex]F_r = \mu mg[/tex]
= 0.70 × 64 kg× 9.8 m/s²
= 439.04 N
The distance covered now can be determined as follows:
d = W/F
d = 327.68 J/ 439.04 N
d = 0.746 m
Explain what a circuit breaker is and how it helps protect your house?
Explanation:
A circuit breaker is an electrical switch designed to protect an electrical circuit from damage caused by overcurrent/overload or short circuit. Its basic function is to interrupt current flow after protective relays detect a fault.
Circuit breakers have been designed to detect when there is a fault in the electricity, so it will “trip” and shut down electrical flow. ... This detection is key to preventing surges of electricity that travel to appliances or other outlets, which can cause them to break down
Three 30 g metal balls, one of aluminum, copper and lead, are placed in a large beaker of hot water for a few minutes. [The specific heats of aluminum, copper, and lead are 903, 385, and 130 J / (kg ° C), respectively].
to. Which of the balls, if any, will reach the highest temperature? Explain.
b. Which of the balls, if any, will have the most heat energy? Explain.
Answer:
The answer is below
Explanation:
Specific heat capacity is an intensive property of a material. The specific heat of a material is the amount of energy required to raise the temperature of one unit mass m of material by one unit of temperature.
a) Temperature is inversely proportional to specific heat capacity. If the same amount of heat is applied to all three balls, the ball that will reach the highest temperature is the ball with the least specific heat capacity.
Hence lead will have the highest temperature since it has the least specific heat capacity.
b) The quantity of heat is directly proportional to the specific heat capacity. Hence if all balls experience the same temperature change, the ball that have the most energy will be that with the highest specific heat capacity.
Hence aluminum will have the most heat since it has the highest specific heat capacity.
When the insulation resistance between a motor winding and the motor frame is tested, the value obtained is 1.0 megohm (106 Ω). How much current passes through the insulation of the motor if the test voltage is 1000 V?
Answer:
0.001 A
Explanation:
Applying,
V = IR.............. Equation 1
Where V = Voltage of the motor, I = current, R = resistance
make I the subject of the equation
I = V/R.............. Equation 2
From the question,
Given: V = 1000 V, R = 1 MΩ = 10⁶ Ω
Substitute these values into equation 2
I = 1000/10⁶
I = 10⁻³ A
I = 0.001 A
A cylindrical specimen of aluminum having a diameter of 0.505 in. (12.8 mm) and a gauge length of 2.0 in. (50.8 mm) is pulled in tension. Use the load-elongation characteristics tabulated below to complete parts (a) through (f).
a. Plot the data as engineering stress versus engineering strain.
b. Compute the modulus of elasticity.
c. Determine the yield strength at a strain offset of 0.002.
d. Determine the tensile strength of this alloy.
e. What is the approximate ductility, in percent elongation?
f. Compute the strain energy density up to yielding (modulus of resilience).
( Load in N Load in lb Length in mm Length in in. 2.000 2.002 2.004 2.006 2.008 2.010 2.020 2.040 2.080 2.120 2.160 2.200 2.240 2.270 2.300 2.330 Fracture 50.800 7330 15,100 3400 23,100 5200 30,400 6850 34,400 7750 38,400 8650 41,3009300 44,800 10,100 46,200 10,400 53, 47,300 10,650 54.864 47,500 10,700 55.880 46,100 10,400 44,800 10,100 42,600 9600 3,400 8200 Fracture Fracture Fracture 50.851 50.902 50.952 51.003 51.054 1650 51.308 51.816 52.832 848 56.896 57.658 58.420 59.182
Answer:
A cylindrical specimen of aluminum having a diameter of 0.505 in. (12.8 mm) and a gauge length of 2.0 in. (50.8 mm) is pulled in tension. Use the load-elongation characteristics tabulated below to complete parts (a) through (f).
recognizing forms of energy
Answer:
hi the question isn't obvious and need a photo I guess
In 2009 Usain Bolt set the world record time by running 100 meters in 9.58 s. Assume that during this race he ran in a straight line with constant acceleration a. What would be the required constant acceleration a
In 2009 Usain Bolt set the world record time by running 100 meters in 9.58 seconds, assuming that he ran this race with constant acceleration, then the required constant acceleration would have been
What are the three equations of motion?There are three equations of motion given by Newton
v = u + at
S = ut + 1/2×a×t²
v² - u² = 2×a×s
By using the second equation of motion given by Newton,
S = ut + 1/2at²
100= 0 + 0.5*a*9.58²
a = 2.17 meters / second²
Thus,the required constant acceleration of Usain Bolt would have been 2.17 meters / second².
To learn more about equations of motion here, refer to the link;
brainly.com/question/5955789
#SPJ2
