it will take 30.65 minutes for the thermocouple to read 99 percent of the initial temperature difference. (∅/∅i = 0.01).
The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. So, the radius, r = 0.6 mm = 0.0006 m, the volume of the sphere, V = (4/3)πr³, and the area of the sphere, A = 4πr².
The properties of the junction are k = 35 W/m °C, p = 8500 kg/m³, and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m² °C.
We have, thermal conductivity of the sphere = k = 35 W/m °C, density of the sphere = p = 8500 kg/m³, specific heat of the sphere = Cp = 320 J/kg °C, and heat transfer coefficient between the sphere and the gas, h = 65 W/m² °C.
The initial temperature difference is given by, ΔT₀ = 1°C = 1 K. Let, the time taken for the thermocouple to read 99% of the initial temperature difference, ΔT99 = 0.99 K.
Let, the thermal diffusivity of the sphere be,
α = k / (pCp) = (35 W/m °C) / (8500 kg/m³ x 320 J/kg °C) = 0.000012868 m²/s.
And, the Biot number is given by, Bi = (h x A) / k = [(65 W/m² °C) x 4π(0.0006 m)²] / (35 W/m °C) = 0.0492.
The equation for the unsteady-state temperature profile of a sphere is, θ(r,t) = Σ [(-1)n+1 / n] exp(-n²π²αt / r²) sin (nπr / R), where R is the radius of the sphere. We can estimate the time taken for the thermocouple to read 99% of the initial temperature difference using a semi-log plot of θ/ΔT vs. t/ti.
This plot is linear and of the form, θ/ΔT = 1 - A exp (-Bt/ti), where A = 0.01 and B = (nπ/R)².So, θ/ΔT = 0.99 = 1 - A exp (-Bt/ti), or 0.01 exp (-Bt/ti) = 0.01/0.99, or exp (-Bt/ti) = 1/99, or -Bt/ti = ln (1/99), or t/ti = ln (99).
Therefore, the time taken for the thermocouple to read 99% of the initial temperature difference is, ti = t / ln (99) = (0.000012868 m²/s) (0.6 mm)² / (35 W/m °C) ln (99) = 1838.98 s or 30.65 minutes.
To know more about thermocouple, refer here:
https://brainly.com/question/14555057#
SPJ11#
When only one lightbulb blows out, an entire string of decorative lights goes out. The lights in this string must be connected in
a. parallel with one current pathway
b. parallel with multiple current pathways
c. series with one current pathway
d. series with multiple current pathways
When only one lightbulb blows out, an entire string of decorative lights goes out, which means that the lights in this string must be connected in series with one current pathway.
In a series circuit, the components are connected end to end in a single path, so the current flows through each component in turn. If one component, such as a lightbulb, fails, the circuit becomes incomplete, and the current cannot flow through any of the components downstream of the failed component. This results in all the lights in the series circuit going out when one lightbulb blows out.
In contrast, in a parallel circuit, the components are connected across multiple current pathways, so if one component fails, the current can still flow through the other components, and they will continue to function normally. Therefore, if one lightbulb blows out in a parallel circuit, the other lights will continue to work.
Learn more about the series circuit:
https://brainly.com/question/19865219
#SPJ11
One object is placed on each shelf in the image above (W, X, Y, Z). The four objects have the same mass, 2.0 kg. Match each object to its potential energy.
Object W 7.84 J 15.7 J 13.4 J 0 J 23.5 J 5.62
Object X
Object Y
Object Z
Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7J and 23.5J, for better understand we have to know the meaning of potential energy.
What is Potential Energy?Potential energy in physics is the energy that an item retains as a result of its location in relation to other objects, internal tensions, electric charge, or other elements. Potential energy develops in systems having components whose configurations, or relative positions, determine the amount of the forces they apply to one another.
Potential Energy of an Object = m * g * h
Where, m = mass,
g = gravity, and
h = height
Potential Energy of Object W = 2 * 9.8 * 0
= 0 J
Potential Energy of Object X = 2 * 9.8 * 0.4
= 7.84 J
Potential Energy of Object Y = 2 * 9.8 * 0.8
= 15.68 J
≈ 15.7 J
Potential Energy of Object Z = 2 * 9.8 * 1.2
= 23.5 J
Therefore, Potential Energy of Object W, X, Y and Z are 0 J, 7.84 J, 15.7 J and 23.5 J.
To Learn more about Potential Energy, visit:
https://brainly.com/question/1242059
#SPJ1
A small cube of iron is observed under a microscope. The edge of the cube is 5.00×10 cm long. Find (a) the mass of the cube and (b) the number of iron atoms in the cube The molar mass of iron is 55.9g/mol, and its density is 7.86g/cm³.
Answer:
Explanation:
a) The mass of the cube can be calculated using the equation Mass = Volume x Density. The volume of the cube can be calculated as (5.00×10 cm)^3 = 125 cm³. Substituting this volume into the equation gives Mass = 125 cm³ x 7.86 g/cm³ = 983.5 g.
b) The number of iron atoms in the cube can be calculated using Avogadro's number (6.02 x 10^23 atoms/mol). The number of moles can be calculated using the molar mass of iron, 55.9 g/mol. Thus, the number of moles can be calculated as 983.5 g / 55.9 g/mol = 17.61 moles. Multiplying this by Avogadro's number gives the number of iron atoms in the cube as 1.07 x 10^24 atoms.
1) A white dwarf is
A) a precursor to a black hole.
B) an early stage of a neutron star.
C) what most stars become when they die.
D) a brown dwarf that has exhausted its fuel for nuclear fusion.
The most appropriate option among the given options is C. A white dwarf is what most stars become when they die.What is a white dwarf?A white dwarf is a small, compact object that is the final stage of stellar evolution for most stars in the universe.
The star exhausts its fuel and begins to cool after it has used up all of the hydrogen fuel that powers its nuclear reactions. This phase of a star's evolution is referred to as a red giant. The star then sheds its outer layers of gas, exposing its core. The hot, glowing core of a star is exposed as a white dwarf once the outer layers have been ejected.What most stars become when they die is a white dwarf. This is one of the most fascinating phenomena in the universe, as well as one of the most intriguing. Furthermore, a white dwarf is a dense, compact object that is frequently composed of carbon and oxygen. It has no more nuclear fuel to burn, therefore it does not produce energy. As a result, it gradually fades away into the blackness of space, eventually turning into a black dwarf. However, it is believed that no black dwarfs have been observed yet.White dwarfs are not precursors to black holes or neutron stars, as those objects are formed from more massive stars that undergo different processes at the end of their lives. Brown dwarfs are also different objects, being failed stars that never achieved the temperature and pressure necessary for sustained nuclear fusion.
For more such questions one white dwarf
https://brainly.com/question/13914155
#SPJ11
Need help on my homework! Thanks.
Answer: Noble Gases (Blue)
consider a single crystal of some hypothetical metal that has the fcc crystal structure and is oriented such that a tensile stress is applied along a direction. if slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 mpa.
Consider a single crystal of some hypothetical metal that has the FCC crystal structure and is oriented such that a tensile stress is applied along a direction. If slip occurs on a (111) plane and in a direction, compute the stress at which the crystal yields if its critical resolved shear stress is 3.42 MPa.
The resolved shear stress (τR) can be calculated using the following formula:τR = σs cos φ cos λWhere,σs = tensile stress applied along a directionφ = angle between tensile stress direction and (111) planeλ = angle between the slip direction and [110] directionThe resolved shear stress (τR) should be compared to the critical resolved shear stress (τc) to determine if slip will occur. If τR > τc, slip will occur. If τR < τc, the crystal will remain undeformed.In this case, the slip direction is also along [110] and therefore φ = λ.
The critical resolved shear stress (τc) = 3.42 MPa. Hence, for slip to occur,τR > τc ⇒ σs cos φ cos λ > τc cos φ cos λ = 3.42 MPaSince φ = λ, we can simplify the above equation toσs > τc / cos φ⇒ σs > 3.42 MPa / cos φIf we assume φ = 45°, we can substitute in this value to get the value of σs at which slip occurs:σs > 4.83 MPa. Therefore, the stress at which the crystal yields is 3.42 MPa.
Learn more about shear stress at:
https://brainly.com/question/30530774
#SPJ11
A slingshot sends a stone vertically upward from a height of 20 feet above a pool of
water. The starting speed of the stone is 90 feet per second. Its distance in feet, d.
above the water is given by the equation:
d-20+90t-16t^2, where t is the time in seconds after the launch.
Drag statements to the table to show what each coordinate labeled on the graph
represents in this problem situation.
the height of the stone when it is launched
the time when the stone hits the water
the time when the stone is launched the maximum height of the stone
the time when the stone reaches its maximum height
Coordinate
A
the height of the stone when it hits the water
What the Coordinate Represents
DRAG AND DROP
AN ITEM HERE
DRAG AND DROP
AN ITEM HERE
DRAG AND DROP
DRAG AND DROP
Coordinate , A - the height of the stone when it hits the water. A slingshot sends a stone vertically upward from a height of 20 feet above a pool of water.
What the Coordinate Represents?The coordinate A represents the height of the stone when it hits the water. When the stone hits the water, its height above the water surface is zero.
So, we can set the expression for the stone's height equal to zero and solve for t to find the time when the stone hits the water. The height of the stone when it is launched is given as 20 feet, which is a fixed value in this problem.
The time when the stone is launched is also a fixed value, which is zero. The maximum height of the stone is the highest point the stone reaches above its initial height of 20 feet. The time when the stone reaches its maximum height is the time at which the vertical velocity of the stone becomes zero.
To know more about vertical velocity , visit :
https://brainly.com/question/11679227
#SPJ1
if the average arterial pressure at your heart is a typical 100 mmhg , what is the average arterial pressure in your hands when they are held at your side? assume your hands are 60 cm below your heart.
The average arterial pressure in your hands when they are held at your side is 47.5 mmHg.
The average arterial pressure in your hands when they are held at your side can be determined using the hydrostatic pressure formula, which is a function of height, gravity, and density. When the hands are held at the side, they are 60 cm below the heart, which means they are at a distance of 0.6 m.
The hydrostatic pressure formula is given by
P = ρgh
Where,
P is the pressure, ρ is the density, g is the acceleration due to gravity, and h is the height. We can assume that the density of blood is constant, and we can take the value of g to be 9.81 m/s², the standard acceleration due to gravity.
Therefore, the pressure at the heart is 100 mmHg, or 100/760 = 0.131 atm. The pressure in the hands can be calculated as follows:
P = ρghP = (1.06 × 10³ kg/m³) × (9.81 m/s²) × (0.6 m)
P = 6.26 × 10³ N/m²
P = 6.26 × 10³ Pa
P = 47.5 mmHg
Therefore, the average arterial pressure in the hands when they are held at the side is 47.5 mmHg.
Learn more about hydrostatic pressure at https://brainly.com/question/28206120
#SPJ11
What is gravity for Galileo?
Galileo famously observed that objects of different masses fall to Earth at the same rate, regardless of their mass. This observation led him to conclude that gravity was a universal force of attraction between any two objects with mass.
Galileo Galilei was an Italian astronomer, physicist, and mathematician who contributed greatly to the development of modern science. His contributions to physics include the creation of the scientific method and his work on the principles of motion and gravity.
Galileo was one of the first scientists to study gravity. He observed that objects of different weights would fall at the same rate when dropped from the same height. This led him to conclude that gravity is a constant force that acts upon all objects equally, regardless of their weight or composition.
Galileo's work on gravity laid the foundation for the later development of Sir Isaac Newton's theory of gravity. Newton built on Galileo's findings and formulated the law of universal gravitation, which states that every object in the universe attracts every other object with a force that is proportional to their masses and inversely proportional to the square of the distance between them.
Learn more about Galileo at https://brainly.com/question/4966012
#SPJ11
a fixed amount of a molecular substance in the liquid phase is placed in a flask at constant temperature. the flask is closed and is allowed to come to equilibrium. select all the statements that correctly describe the processes occurring in the flask. multiple select question. a. the relative amounts of liquid and vapor in the flask remain constant. b. molecules are leaving and entering the liquid phase at the same rate. c. no changes are occurring because the system is at equilibrium. d. the amount of liquid remains the same because evaporation is no longer occurring.
The statements that correctly describe the processes occurring in the flask are A and B. C and D are incorrect statetment.
a) States that the relative amounts of liquid and vapor in the flask remain constant, which is true as equilibrium has been reached, meaning that the rate of evaporation equals the rate of condensation. b) states that molecules are leaving and entering the liquid phase at the same rate, which is also true as equilibrium has been reached.
c) and d) are incorrect because they do not accurately describe the processes occurring in the flask; while the system is at equilibrium, it is still in a state of change with molecules leaving and entering the liquid phase at the same rate.
Learn more about term of equilibrium: brainly.com/question/517289
#SPJ11
You stand 3.5 m in front of a large mirror, and your little sister stands 2.0 m directly in front of you. At what distance should you focus your camera if you want to take a picture of your sister in the mirror?
Answer:
D = 3.5 m to mirror
d = 1.50 m from mirror to sister
Total distance from camera to sister = d + D = 5.0 m
one electron collides elastically with a second electron initially at rest. after the collision, the radii of their trajectories are 0.00 cm and 3.00 cm. the trajectories are perpendicular to a uniform magnetic field of magnitude 0.0350 t. determine the energy (in kev) of the incident electron.
The energy of the incident electron is 26.3 keV. The energy is calculated from the conservation of energy which states that the initial energy is equal to the final energy of the electrons. Total energy is sum of kinetic energy and potential energy of the electrons.
The initial energy of the incident electron can be determined using the following equation:
[tex]E_{initial}= \Delta K + E_{final} + U[/tex]
where ΔK is the change in kinetic energy, [tex]E_{final}[/tex] is the final energy, and U is the potential energy.
Here, the second electron is initially at rest, and after the collision, the trajectories of the two electrons are at 90° to a uniform magnetic field. The magnetic force is perpendicular to the direction of motion, and hence, there is no work done. The potential energy U is, therefore, zero.
Initially, only the incident electron has energy, and hence, its initial energy is equal to its kinetic energy.
[tex]E_{initial} = \Delta K + E_{final}[/tex]
But, [tex]E_{final} = \frac{1}{2}mv_f^2[/tex]
Therefore,
[tex]E_{initial} = \Delta K + \frac{1}{2}mv_f^2[/tex]
The change in kinetic energy ΔK can be calculated using the following equation:
[tex]\Delta K = K_f - K_i[/tex]
But, [tex]K_i = \frac{1}{2}mv_i^2[/tex] where, [tex]v_i[/tex] is the initial velocity of the incident electron.
Therefore,
[tex]\Delta K = K_f - K_i= \frac{1}{2}mv_f^2 - \frac{1}{2}mv_i^2[/tex]
Substituting the given values,
[tex]\Delta K = \frac{1}{2}(9.11 \times 10^{-31} kg)(4.24\times 10^5 m/s)^2 - \frac{1}{2}(9.11\times10^{-31} kg)(3\times10^8 m/s)^2\\= -4.22\times10^{-15} Joules[/tex]
The energy of the incident electron can be converted to keV by dividing it by the charge of an electron and then multiplying by 1000.eV .
Therefore,
[tex]E_{initial} = 4.22 \times 10^{-15} J / (1.602 \times 10^{-19} C/eV)\\ = 26.3 keV[/tex]
Thus, the energy of the incident electron is 26.3 keV.
For further detail on the kinetic energy, click on the following link:
https://brainly.com/question/18461965
#SPJ11
Find the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1. Volume =______
The volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1 is 0.
To determine the volume of the solid obtained by rotating the region in the first quadrant bounded by the curves x = 0, y = 1, x = y^7 about the line y = 1, we need to use a specific integral formula.
The volume of the solid is calculated by multiplying the area of the cross-section of the solid, which is perpendicular to the axis of rotation, with the distance traveled by the center of mass of the cross-section. And, when this product is summed up across the length of the solid, we get the volume of the solid.
To solve the given problem, the area of the cross-section of the solid is [tex]\pi (r)^2[/tex], where r is the distance from the line y = 1 to the curve [tex]x = y^7[/tex]. Since the cross-section is a circle, we know the area of the cross-section can be represented by the equation of a circle with radius r, which is [tex]\pi (r)^2[/tex].
To find the value of r, we will equate [tex]x = y^7[/tex] to the line y = 1. By solving for y, we get: [tex]y = 1^{1/7} = 1[/tex].
Hence, r = 1 - 1 = 0.
We can now compute the volume of the solid using the integral formula:
[tex]V =\int_0^1 \pi (r)^2 dy\\V = \int_0^1 \pi (0)^2 dy\\V = \int_0^1 0 dy\\V = 0[/tex]
Learn more about volume of the solid here:
https://brainly.com/question/24259805
#SPJ11
T/F the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.
The statement the construction of psychological profiles is a process of mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones is TRUE.
Psychological profiling is a technique used by law enforcement agencies to identify the characteristics of an offender based on their behavior patterns, motives, and other psychological traits. It is a process of creating a psychological profile of an offender by analyzing the crime scene, victimology, and other evidence related to the crime.
This profile is then compared with the profiles of previously solved crimes to identify potential suspects or patterns that can be used to solve unsolved crimes. The process involves mapping the characteristics of offenders of previously solved crimes and applying them to offenders of unsolved ones.
The psychological profile is based on the assumption that an offender's behavior is consistent across different crimes and that it reflects their personality traits and motivations. This technique has been used successfully in many high-profile cases and has helped law enforcement agencies to identify and apprehend serial offenders.
To know more about psychological profiles, refer here:
https://brainly.com/question/30398442#
#SPJ11
4. write all of the proper subset relations that are possible using the sets of numbers n, z, q, and r
The proper subset relations that are possible using the sets of numbers n, z, q, and r are:
n ⊆ z, q, and rz ⊆ n, q, and rq ⊆ n, z, and rr ⊆ n, z, and qAn improper subset comprises every element of the original set, while a valid subset only contains a fraction of the original set's numbers. A subset of a set A that is not equal to A is a proper subset of A. In other words, if B is a proper subset of A, then A has at least one element that is not in B but all of B's elements are in A.
Learn more about proper subset at brainly.com/question/17514113
#SPJ11
What does the average kinetic energy of gas depend on?
Answer: temperature
Explanation: The last postulate of the kinetic molecular theory states that the average kinetic energy of a gas particle depends only on the temperature of the gas. Thus, the average kinetic energy of the gas particles increases as the gas becomes warmer.
Five docks are being tested in a laboratory. Exactly at noon, as determined by the WWV
Exactly at noon, as determined by the WWV time signal, on successive days of a week the clocks according to their relative value as good timekeepers, best to worst.
Time signals are also used in many everyday applications, such as GPS navigation, where precise timing is essential for calculating positions accurately. A time signal refers to any signal that provides information about the passage of time. Time signals are often used in experiments to measure the duration of events or to synchronize the timing of multiple processes.
One common type of time signal is a periodic signal, which repeats itself at regular intervals. This can be used to measure the period or frequency of a phenomenon, such as the oscillation of a pendulum or the vibration of a guitar string. Another type of time signal is a pulse signal, which provides a brief burst of energy at a specific time. This can be used to trigger the start or stop of a process or to measure the time delay between different events.
To learn more about Time signal visit here:
brainly.com/question/28875779
#SPJ4
a missile of mass 1.20 102 kg is fired from a plane of mass 4.80 103 kg initially moving at a speed of 3.25 102 m/s. if the speed of the missile relative to the plane is 1.06 103 m/s, what is the final velocity of the plane?
The final velocity of the plane after a missile of mass 1.20 102 kg is fired from the plane is 0.255 m/s.
To find the final velocity of the plane when a missile of mass 1.20 x 10² kg is fired from a plane of mass 4.80 x 10³ kg initially moving at a speed of 3.25 x 10² m/s, and the speed of the missile relative to the plane is 1.06 x 10³ m/s, we can use the conservation of momentum.The initial momentum of the system is given by:
m1v1 + m2v2 = (m1 + m2)vf
where m1 = mass of missile, m2 = mass of the plane, v1 = velocity of the missile, v2 = velocity of the plane, and vf = final velocity of the system
Substituting the given values, we get:(1.20 x 10² kg) (1.06 x 10³ m/s) + (4.80 x 10³ kg) (3.25 x 10² m/s) = (1.20 x 10² kg + 4.80 x 10³ kg) vf
Simplifying, we get:1284 = (5.04 x 10³ kg) vf
Therefore, vf = 1284 / (5.04 x 10³ kg) = 0.255 m/s. So, the final velocity of the plane is 0.255 m/s.
More on velocity: https://brainly.com/question/20038545
#SPJ11
what factor does not determine how much gravitational potential energy is in an object-earth system?
The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass.
An object-earth system is a system in which an object interacts with the earth by exerting a force of attraction. The object's energy is derived from the work done by gravitational forces when the object is moved away from the earth's surface.
An object in an object-earth system's gravitational potential energy is the work done by gravitational forces on the object when it is moved from a lower position to a higher one in the object-earth system. The factor that does not determine how much gravitational potential energy is in an object-earth system is the object's mass. The gravitational potential energy of an object in the earth-object system is determined by the distance between the object and the earth's surface. The gravitational potential energy of an object increases as the distance between it and the earth's surface increases.
Learn more about the gravitational potential at brainly.com/question/19768887
#SPJ11
suppose the roller coaster had had an initial speed of 5 m/s uphill instead, and it coasted uphill, stopped, and then rolled back down to a final point 20 m below the start. we would find in that case that its final speed is the same as its initial. explain in terms of conservation of energy.
In this case, the roller coaster starts with kinetic energy because it has an initial speed of 5 m/s.
Since the roller coaster's total energy is conserved throughout the ride, its final speed when it reaches the bottom will be the same as its initial speed of 5 m/s.
As it goes uphill, the kinetic energy is gradually converted into potential energy, so its speed decreases until it reaches the top, where it has only potential energy. When it stops, all the kinetic energy has been converted to potential energy. As the roller coaster rolls back down, the potential energy is converted back to kinetic energy, and its speed increases until it reaches the bottom, where all the potential energy has been converted back to kinetic energy.
This is because the roller coaster's potential energy at the top is equal to the sum of its initial kinetic energy and the work done by gravity as it went uphill. The roller coaster then converts all of its potential energy back into kinetic energy as it rolls back down the hill.
For more similar questions on conservation of energy and physics:
brainly.com/question/381281
#SPJ11
true or false? a faraday bag stops any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world. true false
True. A Faraday bag (also known as an electromagnetic bag) is a container made from metal or a special material that blocks any electromagnetic emanations from passing into or out of the bag, preventing a mobile device from communicating with the outside world.
This is because Faraday bags are electromagnetic bags that are designed to isolate electronic devices from external electromagnetic influence. They are also known as radiofrequency shielding bags, Faraday cage bags, signal blocker bags, or electromagnetic pulse (EMP) bags.
What are Faraday bags?
Faraday bags are made of a combination of metal or metal-coated fabrics that are designed to block electromagnetic signals from entering or leaving the bag. They are usually used to keep mobile devices such as smartphones and tablets from communicating with the outside world, especially in situations where an individual is worried about their privacy or security. They are also used by law enforcement agencies to prevent suspects from remotely wiping or deleting evidence on their devices.
How do Faraday bags work?
Faraday bags work by using a principle known as the Faraday effect, which states that any electric field in a conductor is shielded from the conductor's interior by the presence of an electric field. Faraday bags use this principle to block incoming and outgoing signals by creating an electrically conductive enclosure around the device. This means that when a mobile device is placed inside a Faraday bag, the bag acts as a Faraday cage, which shields the device from electromagnetic radiation. As a result, the device cannot communicate with the outside world.
For further details about Faraday bag, click on the below link:
https://brainly.com/question/23083952
#SPJ11
a -pound elevator is suspended by a -foot cable that weighs lb/ft. how much work is required to raise the elevator from the basement to the third floor, a distance of ft?
The work required to raise the elevator from the basement to the third floor is equal to the force times the distance moved. The work required is equal to (-pounds)(ft) = -foot-pounds.
We have to calculate the work required to raise the elevator from the basement to the third floor using the given data. In order to calculate the work, we need to determine the force required to lift the elevator.
This can be done using the equation: F = W + w x L
where, F is the force required to lift the elevator, W is the weight of the elevator, w is the weight of the cable per foot, and L is the length of the cable. F = 1500 + (0.4 × 75) = 1500 + 30 = 1530 pounds.
Therefore, the force required to lift the elevator is 1530 pounds. The work done to raise the elevator is given by the equation: W = F × d
where, W is the work done, F is the force required to lift the elevator, and d is the distance traveled by the elevator.
W = 1530 × 30 = 45,900 foot-pounds.
Therefore, the work required to raise the elevator from the basement to the third floor is 45,900 foot-pounds.
Read more about the distance ;
https://brainly.com/question/26550516
#SPJ11
When Joselyn went to the store she bought 2.7kg of salt water taffy. What would Joselyn do to find out how many grams she bought?A. Divide by 1000B. Multiply by 1000C. Divide by 100D. Multiply by 100
At the shop, Joselyn purchased 2700 grammes of salt water taffy.
To convert kilograms (kg) to grams (g), Joselyn would need to multiply the weight in kilograms by 1000. This is because there are 1000 grams in 1 kilogram. Therefore, to find out how many grams of salt water taffy Joselyn bought, she would need to multiply 2.7kg by 1000.
The correct answer is (B) Multiply by 1000.
Multiplying 2.7kg by 1000 gives:
2.7kg x 1000 = 2700g
So Joselyn bought 2700 grams of salt water taffy at the store.
To learn more about salt water refer to:
brainly.com/question/6829606
#SPJ4
A car’s cooling system contains 25 kg of water. What is the increased change in temperature of the water if 872. 0 kJ of thermal energy is added?
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
Water's specific heat capacity (J/(gK), or 4,180 J/ (kgK). Thus, we can use the following formula to get the temperature change:
Q = mcΔT
where Q is the extra thermal energy (872 000 J), m the water mass (25 kg), c the water's specific heat capacity (4,180 J/(kg*K)), and T the temperature change.
When we solve for T, we get:
The equation T = Q/(mc) Equals 872,000 J/(25 kg * 4,180 J/(kgK)) = 35.0 °C.
When 872.0 kJ of thermal energy are injected, the temperature of the 25 kg of water in the car's cooling system changes by 35.0 degrees Celsius.
learn more about energy here:
https://brainly.com/question/1932868
#SPJ4
what would happen to the gravitational force between the sun and sirius, another main sequence star, if the mass of sirius were to triple?
Answer:
It would triple.
Explanation:
By Newtown's law of universal gravitation, the ration is 1:1
Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. Place them in order from the oldest (earliest in fossil record = most ka) to the youngest (most recent in fossil record = least ka).
1. Omo Kibish: incomplete fossil skull (oldest)
2. Herto: a skull intermediate between H. heidelbergensis and modern H. sapiens
3. Klasies River: fragmentary hominin remains
4. Tianyuan Cave: modern human maniple and femur (youngest)
Hominin remains have been found at sites throughout Africa, Europe, and Asia. Below are five of these fossil sites and their main finds. The correct order of the given hominin fossil sites from oldest to youngest is Omo kibish, Klasies river, Herto, and Tianyuan cave.
Omo kibish is incomplete fossil skull (oldest)The oldest fossil site on the list is Omo kibish in Ethiopia, which is dated to around 195,000 years ago. The site has a partial skull, lower jawbone, and a few other fragments of the skull. Klasies river is fragmentary hominin remains Klasies river Mouth in South Africa is dated back to around 120,000 years ago. The site contains human fossils along with the remains of other animals.
Herto is a skull intermediate between H. heidelbergensis and modern H. sapiens, Herto Bouri in Ethiopia, dated to around 160,000 years ago. The site contains 3 complete hominid skulls which were much more modern than expected for their age. The skulls were similar to Homo sapiens, but with some differences. Tianyuan cave is modern human maniple and femur (youngest). Tianyuan cave in China, dated to around 40,000 years ago, contains one of the earliest modern human fossils. A complete set of human teeth and bones from a foot, leg, and hand were found at this site.
Learn more about hominin at:
https://brainly.com/question/30791663
#SPJ11
what's the correct answer.
The coordinated functions of the Nervous, Endocrine, and Reproductive systems are:
D. CerebrumN. Wernicke's AreaF. Occipital LobeH. HypothalamusJ. ThalamusH. HypothalamusC. CerebellumL. Superior ColliculusA. AmygdalaM. Pineal GlandWhat are coordinated functions?Coordinated functions refer to the integration and communication between different organs, systems, and tissues in the body to achieve a common goal or purpose. In biological terms, coordinated functions often involve multiple physiological systems working together to maintain homeostasis, respond to stimuli, or carry out complex behaviors or processes.
Examples of coordinated functions include the regulation of blood glucose levels by the pancreas and liver, the coordination of movement by the nervous and musculoskeletal systems, and the release of hormones by the endocrine system to control various physiological processes.
Learn more on coordinated functions here: https://brainly.com/question/15686131
#SPJ1
The question is:
"COORDINATED FUNCTIONS OF THE NERVOUS, ENDOCRINE, AND REPRODUCTIVE SYSTEMS"
Directions: Identify the part of the brain that is involved in each situation below. Write only the letter of your answer.
A. Amygdala
B. Brocka's Area
C. Cerebellum
D. Cerebrum
E. Hippocampus
F. Occipital Lobe
G. Hippocampus
H. Hypothalamus
I. Inferior Colliculus.
J. Thalamus
K. Pons
L Superior Colliculus
M. Pineal Gland
N. Wernicke's Area
O. Pituitary Gland
1. "My heart tells me that you are the one. I love you so much!"
2. "IAOCEVOY! I don't know what that means. It's all Greek to me!"
3. "Chartreuse, Olive,Turquoise, and Mint are all shades of green."
4. "Janna always wakes up at 4 in the morning, regardless of whether she uses an alarm clock or not."
5. "I don't remember the way going to Myla's house. Can you accompany me there?"
6. Jenny's mother is about to give birth, she complains about contraction and pain usually when the baby is kicking
7. "Anthony is a very skilled dancer. He just won the school hip hop dance competition last week."
8. "As Nica was walking on the road she readily moved to the side for she heard an incoming ambulance"
9. "Elsa loves making faces whenever she talks to her friends."
10. "Ryan usually talks about how happy his high school days were to his grandchildren."
A block of weight w = 25.0 N sits on a frictionless inclined plane, which makes an angle 8 = 29.0° with respect to the horizontal, as shown in the figure. (Figure 1) A force of magnitude F = 12.1 N, applied parallel to the incline, is just sufficient to pull the block up the plane at constant speed.
Part B: What is We, the work done on the block by the force of gravity was the block moves a distance L = 3.40 m up the incline?
Part C. What is Wf the work done on the block by the applied force F as the block moves a distance L = 3.40 mm up the incline? Express your answer in Joules
a) The net Work done is zero. b) The work done on the block by the applied force F as the block moves a distance L is -41.2 J. c) The work done on the block by the applied force F as the block moves a distance L is 41.2 J.
Given:
Weight of the block (w) = 25.0 N
Distance moved by the block (d) = 3.40 m
The angle of the inclined plane (θ) = 29.0°
a) we know that from the work-energy theorem,
W = change in kinetic energy
But since speed is constant which means no change in KE, hence the net Work done is zero.
b) W = -mgy
W = -25 × (3.10 × sin29°)
W = -41.2 J
Therefore, the work done on the block by the force of gravity is -41.2 J.
c) The work done on the block by the applied force F as the block moves a distance L = 3.10m up the incline is,
W = Fd
W = 12.1 × 3.1
W = 41.2 J
Therefore, the work done on the block by the applied force F as the block moves a distance L is 41.2 J.
To know more about the work done:
https://brainly.com/question/26622905
#SPJ12
In the context of the motor control process related to the speed-accuracy trade-off, the _____ phase of movement includes the beginning of limb movement in the direction of a target.
In the context of the motor control process related to the speed-accuracy trade-off, the initiation phase of movement includes the beginning of limb movement in the direction of a target.
What is motor control?Motor control is the ability to regulate and coordinate motor skills to achieve a desired outcome. The central nervous system (CNS) is in charge of regulating these skills. The CNS is divided into two parts: the peripheral nervous system (PNS) and the central nervous system (CNS). Motor skills are regulated by both parts of the nervous system. The CNS, on the other hand, is more involved in higher-level motor control.
A motor control system can be divided into three stages: planning, initiation, and execution. When the central nervous system processes the desired movement, it activates the motor program in the initiation stage, which produces the motor command sent to the muscles. Movement is initiated by the initiation stage. Following that, the movement is executed to meet the task's requirements. The motor program adjusts movement by making corrections based on previous trials and feedback. Therefore, the initiation phase is critical in the context of the motor control process related to the speed-accuracy trade-off.
Learn more about Motor control here:
https://brainly.com/question/29769703
#SPJ11
you are using a 1 cir pump which is producing 7.2 gal/min. the pump's shaft is being turned at 1,804 rpm. what is the volumetric efficiency of the pump (as a decimal)?
The Volumetric efficiency of the pump is the ratio of the actual capacity to the theoretical capacity of the pump.
Volumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pump
Given Information
The provided information is,
1 cir pumpCapacity of the pump = 7.2 gal/minSpeed of the shaft = 1804 rpmFind
Volumetric efficiency of the pumpThe theoretical capacity of the pump is given by the following formula,
Theoretical capacity of the pump = π/4 x d² x l x n
where:
π = 3.14d = diameter of the pump l = length of the pump n = speed of the pumpFor the given problem,
Theoretical capacity of the pump = π/4 x d² x l x nπ = 3.14d = ?l = ?n = 1804 rpmWe need to find the diameter of the pump and length of the pump to calculate the theoretical capacity of the pump.
Now, we have the actual capacity of the pump.
Actual capacity of the pump = 7.2 gal/min = 7.2 x 0.13368 m³/min = 0.962496 m³/minVolumetric efficiency of the pump = Actual capacity of the pump / Theoretical capacity of the pumpAs we don't have the diameter and length of the pump, it is impossible to calculate the theoretical capacity of the pump.
Hence, the Volumetric efficiency of the pump cannot be calculated.
Learn more about Volumetric efficiency: https://brainly.com/question/14783214
#SPJ11
