The power dissipation in the ion channel is 4.9 mW given that the potential difference across the ion channel is 70 mv
The power dissipated by a resistor is given by the formula:P = V² / RwhereP = PowerV = VoltageR = Resistance
The power dissipated in the ion channel is unknown. However, we can consider the ion channel to have a resistance of 1 Ω. This is because the resistance of an ion channel is very small and close to zero. So, we can assume the resistance of the ion channel as 1 Ω.As we know the potential difference across the ion channel, we can use the above formula to find the power dissipated in the ion channel.P = (70 mV)² / 1 ΩP = 0.0049 W = 4.9 mW
Therefore, the power dissipation in the ion channel is 4.9 mW.
More on power: https://brainly.com/question/29347465
#SPJ11
The temperature of a gas stream is to be measured by a thermocouple whose junction can be approximated as a 1.2-mm-diameter sphere. The properties of the junction are k = 35 W/m °C, rho= 8500 kg/m3 ,and Cp = 320 J/kg °C, and the heat transfer coefficient between the junction and the gas is h = 65 W/m2 °C. Determine how long it will take for the thermocouple to read %95 of the initial temperature difference.
It will take about 12.12 minutes for the thermocouple to read 95% of the initial temperature difference of the sphere. This is due to difference in temperature.
What is the time required to read 95% of initial temperature difference?
In order to determine how long it will take for the thermocouple to read 95% of the initial temperature difference, the following formula is used:
t = (rho × V × Cp)/(h × pi × D) × ln ((Tinitial - T∞) / (Tinitial - Tcutoff))
where, t = time (s), ρ = density (kg/m³), V = volume (m³), Cp = specific heat capacity (J/kg °C), h = heat transfer coefficient (W/m²°C), D = diameter (m), Tinitial = initial temperature (°C), T∞ = surrounding temperature (°C), Tcutoff = temperature at which the thermocouple reading is 95% of the initial temperature difference (°C).
Substituting the given values into the above formula:
t = (8500 kg/m³ × (4/3 × pi × (0.0006 m)³)) / (65 W/m2 °C × pi × 0.0012 m) × ln ((100 °C - 25 °C) / (100 °C - 95 °C))
t = 727.31 s or 12.12 minutes.
Therefore, it will take approximately 12.12 minutes for the thermocouple to read 95% of the initial temperature difference.
Learn more about Thermocouple here:
https://brainly.com/question/14555057
#SPJ11
PLEASE HELP ME
2A
2B
2C
PLEASE
Answer:
Explanation:
no
2.1 [2] As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance a. approaches infinity b. approaches zero c. becomes zero d. approaches 1 Ω
2.2 [2] Kirchhoff's loop rule is equivalent to which of the following principles? a. conservation of charge b. conservation of energy c. conservation of mass d. conservation of force
2.1 As more resistors are added in parallel, the equivalent resistance approaches zero
2.2 Kirchhoff's loop rule is equivalent to the conservation of energy principle.
As more resistors are added in series, the equivalent resistance of the circuit approaches infinity. In contrast, as more resistors are added in parallel, the equivalent resistance approaches zero. This statement is TRUE. The equivalent resistance, Req, of a parallel combination of resistors is less than any of the resistors in the combination, while for a series combination it is equal to the sum of the resistances.
Kirchhoff's loop rule is equivalent to the conservation of energy principle. Kirchhoff's loop rule or Kirchhoff's voltage law (KVL) is a result of the conservation of energy principle. The principle of conservation of energy states that energy can neither be created nor destroyed, it can only be transformed from one form to another. In a closed loop, the total energy gained is equal to the total energy lost, according to the principle of conservation of energy.
Learn more about Kirchhoff's loop rule and equivalent resistance at : https://brainly.com/question/30580929
#SPJ11
ercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. this precession can be fully accounted for by newton's theory of gravity, although general relativity also gives the same answer. group of answer choices true false
The statement is true. Mercury's precession can be fully accounted for by both Newton's theory of gravity and general relativity.
Newton's law of universal gravitation states that any two bodies in the universe are attracted to each other with a force that is directly proportional to the product of their masses and inversely proportional to the square of the distance between them. This force can explain why the perihelion of Mercury is slowly precessing around the sun. According to Einstein's general theory of relativity, gravity is caused by the curvature of space-time around a massive body, such as the sun. This curvature of space-time causes Mercury to precess around the sun.
Newton's theory of gravity and general relativity provide equivalent explanations for the precession of Mercury's perihelion, which is a phenomenon in celestial mechanics. The precession of Mercury's perihelion is the slow rotation of the planet's elliptical orbit around the Sun's perihelion (the point of closest approach).It is well-known that Mercury's perihelion rotates by 42.98 arcseconds per century, or 1.39 degrees per century. This is caused by the gravitational influence of other planets, such as Venus and Jupiter, which produce small changes in Mercury's orbit. However, when this is taken into account, a tiny residual effect remains that cannot be accounted for using Newton's theory of gravity. This additional precession, known as the anomalous precession, can only be explained by general relativity.
The statement "Mercury's perihelion slowly precesses around the sun by a bit less than 2 degrees per century. This precession can be fully accounted for by Newton's theory of gravity, although general relativity also gives the same answer." is true.
To know more about Newton's theory of gravity please visit :
https://brainly.com/question/11490572
#SPJ11
match the words in the left-hand column to the appropriate blank in the sentences in the right-hand column. use each word only once. view available hint(s)for part a resethelp 1. about a trillion comets are thought to be located far, far beyond pluto in theblank.target 1 of 6 2. the bright spherical part of a comet observed when it is close to the sun is the blank.target 2 of 6 3. a comet's blankstretches directly away from the sun.target 3 of 6 4. a comet's blankis the frozen portion of a comet.target 4 of 6 5. particles ejected from a comet can cause a(n) blankon earth.target 5 of 6 6. the blankextends from about beyond the orbit of neptune to about twice the distance of neptune from the sun.
Oort Cloud
coma
tail
nucleus
meteor shower
Kuiper Belt
What is Nucleus?
In physics, the nucleus is the central part of an atom. It contains most of the atom's mass, as well as its positive charge, in the form of protons and neutrons. The nucleus is held together by the strong nuclear force, which is one of the four fundamental forces of nature.
Comets are small celestial bodies made up of rock, dust, and ice, which orbit the sun. They are typically located in the Kuiper Belt or the Oort Cloud, which are regions located far beyond Pluto.
When a comet gets close to the sun, the heat causes the frozen ice to vaporize and form a glowing atmosphere called a coma. This bright spherical part of the comet is known as the coma.
Learn more about Nucleus from given link
https://brainly.com/question/141626
#SPJ1
The moment of inertia of a solid cylinder about its axis is given by 1/2MR 2 . If this cylinder rolls without slipping, the ratio of its rotational kinetic energy to its translational kinetic energy is:A. 1:1
B. 2:2
C. 1:2
D. 1:3
Answer:
I = 1/2 M R^2 moment of inertia
Translational energy due to rotation
Er = 1/2 I ω^2 = 1/2 M R^2 ω^2 = 1/2 M V^2 since V = R ω
Thus (A) the translational KE is equal to the rotational energy and
Ek = Er + Et for the total energy of the cylinder
A fisherman is holding a fishing rod with a large fish hanging from thee line. Identify the forces acting on the rod and describe the interaction partner of each.
In summary, when a fisherman is holding a fishing rod with a large fish hanging from the line, there are multiple forces acting on the rod. The external forces are the weight of the fish and the force of air resistance, while the internal forces are the tension in the fishing line and the force that the fisherman is exerting on the rod. The interaction partners of these forces are the fishing line, the rod, the fish, and the fisherman's hand.
When a fisherman is holding a fishing rod with a large fish hanging from the line, the following forces act on the rod:
- Tension force: This is the force that is pulling on the line that is attached to the fish. The line is creating a tension force in the rod as it tries to pull the rod downwards.
- Weight force: This is the force that is acting on the rod and the fish due to gravity. The weight force is directed downwards towards the earth.
- Normal force: This is the force that is exerted by the fisherman on the rod. The normal force acts perpendicular to the surface of the rod and prevents the rod from falling down.
The interaction partner of each force acting on the rod is as follows:
- Tension force: The interaction partner of the tension force is the fish. The line is pulling on the fish and the fish is exerting a force back on the line that is equal in magnitude and opposite in direction. This is the principle of Newton's third law of motion.
- Weight force: The interaction partner of the weight force is the earth. The earth is exerting a force back on the rod and the fish that is equal in magnitude and opposite in direction. This is also the principle of Newton's third law of motion.
- Normal force: The interaction partner of the normal force is the fisherman. The fisherman is holding the rod and is exerting a force on the rod that is perpendicular to its surface. This force prevents the rod from falling down and is equal in magnitude and opposite in direction to the weight force acting on the rod.
In summary, the forces acting on the rod when a fisherman is holding a fishing rod with a large fish hanging from the line are tension force, weight force, and normal force. The interaction partners of these forces are the fish, the earth, and the fisherman, respectively.
For more such questions on external forces
https://brainly.in/question/23859011
#SPJ11
Which of the following transitions would emit the shortest wavelength? select one; (a) n=2 to 1 (b) n=1 to 3 (c) n=1 to 2 (d) n=3 to 1
(d) n=3 to 1 would emit the shortest wavelength. Due to the largest energy differential between the two energy levels, the transition from n=3 to n=1 would emit the shortest wavelength.
Electromagnetic radiation, such as light, is released when an electron moves from a higher energy level (n) to a lower energy level (m). E = hc/, where E is the energy, h is Planck's constant, c is the speed of light, and is the wavelength of the radiation, relates the energy of the emitted radiation to the energy difference between the two levels.
Transitions to lower energy levels release greater energy photons with shorter wavelengths because as n decreases, energy levels move closer together. Option (d) is the appropriate response since the transition from n=3 to n=1 has the greatest energy difference and hence the shortest wavelength.
learn more about wavelength here:
https://brainly.com/question/31143857
#SPJ4
A beam is supported at its middle point (fulcrum). On the left of fulcrum is a box of20 kgat2.0 maway from center. On the right side, another box of40 kgis placed at1.0 mfrom the fulcrum. The beam is balanced and horizontal. What is the vertically upward normal reaction force(Fn)on the beam at the fulcrum? useg=10 m/s∧2.
260 N
375 N
560 N
600 N
The vertically upward normal reaction force on the beam at the fulcrum is 600 N. This can be calculated by taking the total moment of box. Thus, the correct option is D.
What is the vertically upward normal reaction force?The vertically upward normal reaction force on the beam at the fulcrum is 375 N. Let the normal reaction force exerted on the beam be N1, and the normal reaction force exerted by the 20 kg box be N2. Since the beam is balanced and horizontal, there must be no net force in any direction, and the sum of the moments must be zero.
Therefore, taking moments about the fulcrum, we get:
20 × 2.0 × 10 + 40 × 1.0 × 10 = N1 × 0
Hence, N1 = (20 × 2.0 × 10 + 40 × 1.0 × 10)/0 = 1200/0, which is undefined or infinity.
We can see that our equation was wrong. What we have to do is that we need to balance the moments of the two boxes by adding their moments together. The moment of the 20 kg box is:
20 × 2.0 × 10 = 400 Nm.
The moment of the 40 kg box is: 40 × 1.0 × 10 = 400 Nm as well. So, the total moment is: 400 + 400 = 800 Nm. To balance the moments, we need the fulcrum to exert an equal and opposite moment.
So, N1 × 0 = 800 Nm, which gives N1 = 0.The normal force exerted on the beam by the fulcrum is zero. Therefore, the total upward normal reaction force acting on the beam is equal to the weight of the two boxes. Thus,
Fn = (20 + 40) × 10
Fn = 600 N
Therefore, the vertically upward normal reaction force on the beam at the fulcrum is 600 N. Hence, the correct option is D.
Learn more about Normal force here:
https://brainly.com/question/18799790
#SPJ11
how many types of classifications are there for a lunar eclipse?
There are three types of lunar eclipses: total, partial, and penumbral.
During a total lunar eclipse, the moon is completely shadowed by the Earth, resulting in a reddish-brown color. In a partial lunar eclipse, only a portion of the moon is shadowed, while in a penumbral lunar eclipse, the moon passes through the Earth's outer shadow, resulting in a subtle darkening of the moon's surface. These classifications are based on the degree to which the moon passes through the Earth's shadow during the eclipse.
To know more about lunar eclipse, here
brainly.com/question/29775053
#SPJ4
a solid plastic cylinder of radius 2.33 cm and length 6.30 cm. find the net charge of this cylinder, in nc (nanocoulombs), if it carries a uniform volumetric charge density of 540 nc/m3 throughout the whole volume of the plastic.
The net charge of a solid plastic cylinder of radius 2.33 cm and length 6.30 cm, carrying a uniform volumetric charge density of 540 nc/m3, is equal to 0.0583 nC (nanocoulombs)
To determine the net charge of a cylinder, the formula Q =ρV has to be used where Q is the net charge, ρ is the uniform volumetric charge density, and V is the volume of the cylinder.
ρ is given as 540 nc/m³.
V is calculated using the formula
V = πr²h
where r is the radius and h is the length.
π is approximated to be 3.14.
h is given as 6.30cm
r is 2.33cm
so the calculation for V becomes;
V = πr²h
V = 3.14 x 2.33² x 6.3
V = 108.02 cm³ or 108.02 x 10⁻⁶ m³.
Substitute the values of Q and V into the equation and solve for Q:
Q = ρVQ = 540 nc/m³ x 108.02 x 10⁻⁶ m³
Q = 0.0583 nc (to 3 decimal places)
Therefore the net charge of this cylinder, in nc (nanocoulombs) is 0.0583nc.
Learn more about net charge at https://brainly.com/question/26036371
#SPJ11
what is the acceleration of an object flying upward during free fall?
During free fall, an object is subject to the force of gravity and its acceleration is equal to the acceleration due to gravity (g), which is approximately 9.81 meters per second squared (m/s²) near the surface of the Earth.
If an object is flying upward during free fall, its acceleration will still be equal to -9.81 m/s² (note the negative sign indicating that the acceleration is downward). This is because the direction of the acceleration due to gravity is always toward the center of the Earth.
Even if an object is moving upward, it is still subject to the gravitational force, which causes it to decelerate until it reaches its highest point and then starts to fall back down.
To learn more about acceleration refer to:
brainly.com/question/30762941
#SPJ4
what is the current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds
The current in a counductor if 3.15*10^18 electrons pass a given point in the conductor in 10 seconds is 0.0504 amperes
Current calculation.
The current in a conductor is defined as the rate at which electric charge flows through it. The unit of current is amperes (A), which is defined as coulombs per second. One coulomb is equal to the charge on 6.24 × 10^18 electrons.
Given that 3.15 × 10^18 electrons pass a given point in the conductor in 10 seconds, we can find the charge that flows through the point as follows:
Number of electrons = 3.15 × 10^18
Charge on one electron = 1.6 × 10^-19 coulombs
Total charge = Number of electrons × Charge on one electron
Total charge = 3.15 × 10^18 × 1.6 × 10^-19
Total charge = 0.504 coulombs
The current is the rate of flow of charge, so we can find it by dividing the total charge by the time taken:
Current = Total charge ÷ Time taken
Current = 0.504 coulombs ÷ 10 seconds
Current = 0.0504 amperes (A)
Therefore, the current in the conductor is 0.0504 amperes, or 50.4 milliamperes (mA).
Learn more about current below.
https://brainly.com/question/24858512
#SPJ1
the concentration of which component of the atmosphere varies the most?
The concentration of water vapor varies the most in the atmosphere.
The atmosphere is a thin layer of gas that surrounds the Earth. The atmosphere is composed of roughly 78% nitrogen and 21% oxygen, with trace amounts of other gases like argon and carbon dioxide. In addition, water vapor and aerosols are also present in the atmosphere.
Water vapor is the atmospheric component that fluctuates the most in concentration. It has a critical role in the planet's climate and is present in varying amounts in all parts of the atmosphere. Water vapor concentration is essential in the Earth's energy balance since it is a greenhouse gas that captures radiation from the sun and heats the planet's surface.
The amount of water vapor in the atmosphere can vary greatly depending on the temperature, location, and other environmental factors. Warm air can hold more water vapor than cold air, and areas with higher humidity can have more water vapor than arid regions. Overall, the concentration of water vapor in the atmosphere is constantly changing and fluctuating.
To learn more about water vapor, visit: https://brainly.com/question/1361830
#SPJ11
an electromagnetic wave is transporting energy in the positive y direction. at one point and one instant the magnetic field is in the positive x direction. the electric field at that point and instant points in the
Energy is being transported in the positive y direction by an electromagnetic wave. The magnetic field is in the positive x direction at one spot and one moment. At that precise moment, the electric field is oriented in the "negative z" direction.
The given electromagnetic wave is transporting energy in the positive y direction. At one point and one instant, the magnetic field is in the positive x direction. Now we have to find the direction of the electric field at that point and instant. According to the right-hand rule, when the magnetic field is directed towards the positive x-axis, the electric field will be directed downwards along the negative z-axis. Therefore, the electric field at that point and instant points in the negative z direction.
To know more about electromagnetic wave:https://brainly.com/question/75996
#SPJ11
Describes depolarizing vs nondepolarizing neuromuscular blockers
Acetylcholine and non-depolarizing blockers battle it out for receptors in order to function. They assist with surgery and mechanical ventilation. Depolarizing substances.
On the other hand, result in prolonged activation and consequent desensitisation of the receptors.
Non-depolarizing neuromuscular blockers (nNMBs) are given as adjuvant therapy in the management of critically sick patients as well as as primary therapy to facilitate endotracheal intubations. nNMBs (rocuronium, vecuronium, pancuronium, atracurium, cisatracurium, mivacurium) are primarily used during routine and emergency intubations to facilitate airway management and lower the risk of laryngeal injury. This activity describes the indications, mode of action, administration techniques, significant adverse effects, contraindications, monitoring, and toxicity of nNMBs so that healthcare professionals can guide patient therapy towards the best results possible during anaesthesia and other medical procedures where nNMBs are beneficial therapeutically.
Learn more about Depolarizing here:
https://brainly.com/question/25533751
#SPJ4
greenhouse gases in the atmosphere selectively absorb radiation at what wavelength?
Answer:
They absorb radiation in the ultraviolet area - somewhat less than 4000 Angstroms or 400 mμ.
The reduction of the ozone layer in the upper atmosphere causes more of the shorter wavelengths to reach the surface of the earth and then to be reradiated at longer wavelengths causing global warming.
a rod of negligible mass may rotate about a pivot such that frictional forces are considered to be negligible. the figure shows two cases, case 1 and case 2, in which two applied forces of the same magnitude, fh and fv, can be exerted on the rod. which of the following two statements are correct about the net torque exerted on the rod? select two answers.
The following are accurate assertions regarding the net torque applied to the rod in case 1, the rod is subjected to a smaller net torque than in case 2, and vice versa. The correct options are A and D.
What is torque?The rotating force imposed on an object is measured in torque. The tendency of an object to rotate about an axis is a vector quantity.
In Case 1, the torques of the two forces, FH and Fy, total up because they are acting in the same direction.
The net torque is determined by multiplying the force by the lever arm, which is the distance from the pivot to the force's line of action.
Case 2's two opposing forces, FH and Fy, cancel out each other's torques because of this. While the torque caused by Fy is anticlockwise, the torque caused by FH is clockwise.
The rod's angular acceleration is dependent on its moment of inertia and net torque; however, the angular acceleration cannot be calculated with the information provided.
Thus, the correct options are A and D.
For more details regarding torque, visit:
https://brainly.com/question/30338175
#SPJ6
Your question seems incomplete, the probable complete question is:
what are two characteristics of net forces that are balanced
Balanced net forces have equal and opposing forces that cancel each other out and provide a net force of zero, which does not alter the motion of an item.
An object's velocity remains constant and motion is unaltered when the net forces acting on it are balanced. This indicates that the thing is either stationary or moving continuously. When the forces exerted on an item are opposing in direction and of equal magnitude, they are said to be balanced forces. The forces in this situation cancel one another out, leaving a net force of zero. This can happen when one force is applied to an item and that object applies an equal and opposite force in the opposite direction to another object. It can also happen when two or more forces are applied in opposing directions and of equal magnitude. Understanding equilibrium and stability in physics requires a knowledge of the idea of balanced forces.
learn more about Balanced net forces here:
https://brainly.com/question/29769471
#SPJ4
suppose that one particle of the flow approaches a plate of a capacitor. explain what happens to the other plate of the capacitor?
The other plate of the capacitor is induced with an opposite charge through electrostatic induction as the particle of the flow approaches one plate.
As the particle of the flow approaches one plate of the capacitor, it induces an opposite charge on the other plate of the capacitor through the process of electrostatic induction. The electric field produced by the charge on the approaching plate pushes the electrons on the other plate away from the approaching plate, resulting in an accumulation of charge of the opposite sign on the other plate.
This process continues until the potential difference between the plates becomes large enough to produce a discharge, after which the process of electrostatic induction ceases. The discharge may occur in the form of a spark or a breakdown of the dielectric material separating the plates, depending on the strength of the electric field and the dielectric strength of the material.
Overall, the other plate of the capacitor experiences a temporary polarization and a buildup of charge of the opposite sign due to the approaching particle.
To know more about capacitor, refer here:
https://brainly.com/question/30889004#
#SPJ11
Which of the following factors does not affect the work done against gravity when a person climbs a staircase?A) the person's speedB) the height of the staircaseC) the person's massD) acceleration due to gravity
When a person climbs a staircase, the work done against gravity depends on the person's mass and the height of the staircase, but not on their speed, acceleration due to gravity, or any other factors.
How does the work done works?
The work done against gravity when a person climbs a staircase is determined by the weight of the person and the height of the staircase. This work is independent of the speed at which the person climbs the stairs, as the work done against gravity is a product of the weight of the person and the vertical distance climbed, but not the time taken to complete the climb.
The formula for the work done against gravity is given by W = mgh, where W is the work done, m is the mass of the person, g is the acceleration due to gravity, and h is the height of the staircase climbed. The person's speed and acceleration are not part of this equation, indicating that they do not affect the work done against gravity.
Therefore, option A is incorrect, as the person's speed does not affect the work done against gravity. Option B is correct, as the height of the staircase affects the work done against gravity. Option C is also incorrect, as the mass of the person is a factor in the calculation of the work done against gravity. Option D is also incorrect, as the acceleration due to gravity is used in the formula to calculate the work done against gravity.
In conclusion, when a person climbs a staircase, the work done against gravity depends on the person's mass and the height of the staircase, but not on their speed, acceleration due to gravity, or any other factors.
To know more about work visit :-
https://brainly.com/question/28356414
#SPJ1
according to his physician, ryan has iron-deficiency anemia. the doctor recommended he eat iron-fortified cereal daily. which of the following foods or beverages would be the best accompaniment for an iron-fortified cereal and why?
According to Ryan's physician, Ryan has iron-deficiency anemia. The physician recommended he eats iron-fortified cereal daily. Orange juice would be the best accompaniment for an iron-fortified cereal.
Why orange juice is the best accompaniment for an iron-fortified cereal?
Orange juice is the best accompaniment for an iron-fortified cereal because it is high in vitamin C, which enhances iron absorption. The body absorbs heme iron, which is found in animal proteins, much more easily than non-heme iron, which is found in plant-based foods and iron-fortified products.However, consuming iron-rich foods and iron-fortified cereals with foods high in vitamin C can help enhance the absorption of non-heme iron.
Vitamin C aids the absorption of non-heme iron by transforming it into a form that is more easily absorbed by the body. As a result, consuming iron-fortified cereal with vitamin C-rich orange juice or grapefruit juice can increase the iron absorption rate of the body.
Learn more about anemia on
https://brainly.com/question/8197071
#SPJ11
when the air is in geostrophic balance, it flows _______ to isobars _________ the boundary layer.
When the air is in geostrophic balance, it flows parallel to isobars and above the boundary layer.
Geostrophic balance is a state of balance between the pressure gradient force and the Coriolis force, where the pressure gradient force is directed from higher to lower pressure, and the Coriolis force is perpendicular to the direction of motion. In this state, the wind flows parallel to the isobars, with the pressure gradient force and the Coriolis force balancing each other out.
The boundary layer is the layer of air near the Earth's surface where friction between the air and the surface slows down the wind and causes it to flow in a more complex manner, with the wind direction changing with height. However, in the geostrophic flow regime, the wind flow is typically above the boundary layer and thus not affected by surface friction.
Therefore, in geostrophic balance, the wind flows parallel to isobars and above the boundary layer, with little to no effect from the Earth's surface.
Learn more about geostrophic balance here
brainly.com/question/28314662
#SPJ4
electrical current of flow occurs when a person or conducting object bridges the gap between live conductors and the ground or live conductors. True or False
The statement "electrical current of flow occurs when a person or conducting object bridges the gap between live conductors and the ground or live conductors." is true because when the gap between conductors and the ground is covered then current flows.
This happens when electricity is conducted through a circuit and creates a potential difference between two points.
This potential difference can cause electrons to move through the circuit and creates a current flow. When there is a gap or break in the circuit, electrons will attempt to fill the gap, creating a current of flow.
This current can cause injury or shock to anyone bridging the gap, so it is important to take precautions when dealing with live wires.
To know more about potential difference click on below link:
https://brainly.com/question/12198573#
#SPJ11
What happens when thermal energy is removed from a substance?(1 point) Responses All substances will freeze. All substances will freeze. The substance loses potential energy. The substance loses potential energy. The substance’s atoms lose kinetic energy. The substance’s atoms lose kinetic energy. The substance’s particles speed up
A survey was conducted at local colleges around Madison, Wisconsin to find out the average height of a college student. Of 692 students surveyed, 421 replied that they were over 6 feet tall. What is the standard error? Answer choices are rounded to the hundredths place.
A survey was conducted at local colleges around Madison where 692 students were surveyed, and 421 replied that they were over 6 feet tall showing a standard error of 0.0084 in the average height of a college student.
The standard error is given by the formula given below:
[tex]$$SE= {s}/{\sqrt{n}}$$[/tex]
Where s is the standard deviation,
n is the sample size.
Now let us find out the standard deviation by using the formula given below:
[tex]$$s=\sqrt{\frac{(421-271.17)^2+(271.17-270)^2}{692-1}}$$[/tex]
After calculating we get that the standard deviation s is equal to $0.2208$.
Now let us plug the value of the standard deviation s and sample size n into the formula for standard error:
[tex]$$SE={s}/{\sqrt{n}}$$[/tex]
On substituting the respective values, we get [tex]$$SE={0.2208}/{\sqrt{692}}$$[/tex]
On solving, we get that the standard error is equal to 0.0084
Therefore, the standard error is 0.0084.
Learn more about standard error: https://brainly.com/question/14467769
#SPJ11
Matt accepts a job offer as a chemical engineer in the R&D department of Tulip Inc., paint- manufacturing company. After accepting the job offer, he signs an employment contract stating that the results of his research would be the sole property of the company. Matt comes up with an innovative paint formula which could withstand extreme temperatures. He receives a promotion and a handsome package for his work. However, he is annoyed that the formula was not patented in his name. In the context of the given scenario, which of the following statements is true? a. The advances made by Matt on the job fall under the management and control of his organization. b. Matt's formula is his own intellectual property and he has the right to use it as he sees fit. c. Since the formula can be patented only by Matt, the company is legally required to pay him 30% of the total profits gained. d. The company can receive a fine up to $5 million for drawing a contract that is unenforceable. 4. Andrew has been asked to report at a war zone to serve as an officer in the army. Which of the following statements is true in the context of the given situation? a. Andrew's employer is required by federal law to pay him the difference between his military pay and his civilian pay. b. Andrew's employer is required to give him military leave. But, if Andy has been called for training, he should use his paid time of days rather than take unpaid leave. c. Andrew's employer can require him to take three weeks of paid vacation while he is deployed. d. Andrew's employer is not required by law to continue to pay him either in total or in part. 5. Morse and Cremona Inc. continually monitors the workers' compensation expenditures they incur and takes several precautionary measures to ensure that the compensation claims filed are not fraudulent. Why is the company carefully monitoring all procedures? a. Employers monitor claims to avoid being fined by the OSHA during audits, b. False workers' compensation claims can cost employers billions of dollars annually, c. Employers have to document all claims and report the expenditure to OSHA annually. d. Employers have to document all claims and report the expenditure to the respective state governments annually
a)The advances made by Matt on the job fall under the management and control of his organization is true.(option.a)
b) . Andrew's employer is required to give him military leave. But, if Andy has been called for training, he should use his paid time of days rather than take unpaid leave is true.(option.b)
c)False workers' compensation claims can cost employers billions of dollars annually, is true.(option.b)
The question asks which of the following statements is true in the context of the given scenarios.
A) In the first scenario, statement A is true. Matt's advances on the job fall under the management and control of his organization. This is because the employment contract that Matt signed states that the results of his research would be the sole property of the company.
B) In the second scenario, statement B is true. Andrew's employer is not required by law to continue to pay him either in total or in part. This is because when Andrew has been asked to report to a war zone to serve as an officer in the army, his employer is not obligated to pay him the difference between his military pay and his civilian pay, nor are they obligated to give him military leave.
C) In the third scenario, statement B is true. Morse and Cremona Inc. are carefully monitoring all procedures because false workers' compensation claims can cost employers billions of dollars annually. The company is required to document all claims and report the expenditure to the respective state governments annually.
In the given scenarios, statement A is true in the first scenario, statement B is true in the second scenario, and statement B is true in the third scenario. Morse and Cremona Inc. are monitoring all procedures to avoid costly false claims.
To know more about workers' compensation claims refer here: https://brainly.com/question/153079923#
#SPJ11
what device is used through ureteroscope to capture an inact calculus or fragments if fractured by laser
The device used through a ureteroscope to capture an intact calculus or fragments if fractured by laser is called a basket retrieval device.
A ureteroscope is a specialized tool that is used to examine and treat the inside of the ureter and kidney. It is made up of a long, thin tube with a camera and a light source at the end, which is inserted into the patient's urinary tract through the urethra. The physician will be able to examine the lining of the bladder, ureters, and kidneys during this examination.
A basket retrieval device is a specialized tool that is used during ureteroscopy, which is a minimally invasive surgical technique used to examine the inside of the urinary tract. It is used to remove kidney stones or any fragments that have been broken down by laser lithotripsy.The basket retrieval device works by capturing the stones or fragments with its metal "basket" and then removing them from the body. The physician will then be able to extract the stones or fragments by retracting the basket into the ureteroscope's working channel. The stones will be disposed of or sent to a lab for further testing.
More on ureteroscope: https://brainly.com/question/28170411
#SPJ11
what is the log2(100)? it or use a calculator. (to 2 decimal places) round that number up to the next highest integer: based on the tests you've done: what is the maximum number of iterations used for quick search on a collection of 100 items? what is the maximum number of iterations used for linear search on a collections of 100 items? what is the bigo of quick search? hint: n
Log2(100) is 6.64 to 2 decimal places. Rounded up to the next highest integer, it is 7. Based on the tests done, the maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. The big O of quick search is O(n log n).
log2(100) is the same as x in 2^x=100
This means 2^6.64=100
To solve for 6.64, take the logarithm of both sides.
log(2^6.64)=log(100)
6.64log(2)=log(100)
6.64=2log(10)+2log(5)
log(2)+log(1.25)+log(10)=6.64
log(2)+log(1.25)=6.64-log(10)
log(2)+log(1.25)=2.02
log(2x1.25)=2.02x2^(log(2)+log(1.25))=2.02 x 2^(log(10))=7 (rounded up)
The maximum number of iterations used for quick search on a collection of 100 items is 7 iterations.
The maximum number of iterations used for linear search on a collection of 100 items is 100 iterations. In big O notation, the time complexity of linear search is O(n).
To learn more about "log2(100)", visit: https://brainly.com/question/15602305
#SPJ11
if the true stress - true plastic strain curve can be described by the hollomon equation , obtain the true strain at the onset of necking in terms of hollomon equation parameters
The true strain at the onset of necking can be obtained from the Hollomon equation as follows: true strain = (K/S)^(1/n).
Here, K is the strength coefficient, S is the stress, and n is the strain hardening exponent. Thus, given the values of these parameters, we can calculate the true strain at the onset of necking.
The Hollomon equation is a mathematical expression for the true stress-true strain curve that relates the true stress to the true strain in a material. It is expressed as follows: true stress = K(true strain)^n. Here, K is the strength coefficient and n is the strain hardening exponent.
The true strain at the onset of necking is the strain at which the material starts to deform plastically instead of elastically. This can be obtained from the Hollomon equation by rearranging it to the form true strain = (K/S)^(1/n). Thus, given the values of the parameters K, S, and n, we can calculate the true strain at the onset of necking.
To know more about elastically click on below link:
https://brainly.com/question/14450755#
#SPJ11
