The angle of the resultant vector is equal to the inverse tangent of the quotient of the y-component divided by the x-component of the resultant vector.
To find the angle of a resultant vector, the vector must be resolved into y-component and x-component.
The y-component of a vector is the product of the magnitude of the vector and the sine of the angle of the vector to the horizontal. The x-component of a vector is the product of the magnitude of the vector and the cosine of the angle of the vector to the horizontal.The angle of this resultant vector is also known as the direction of the vector.
Mathematically, the direction of a resultant vector is given as;
[tex]\theta = tan^{-1} (\frac{R_y}{R_x} )\\\\where;\\\\\theta \ is \ the \ direction \ of \ the \ resultant \ vetcor\\\\R_y \ is \ the \ magnitude \ of \ the\ vector \ resolved \ in \ y - direction\\\\R_x \ is \ the \ magnitude \ of \ the\ vector \ resolved \ in \ x - direction[/tex]
Therefore, the angle of the resultant vector is equal to the inverse tangent of the quotient of the y-component divided by the x-component of the resultant vector.
Lear more here: https://brainly.com/question/3224643
cyclist always bends when moving the direction opposite to the wind. Give reasons
I only need help with e (bottom of the page).
Explanation:
The box is accelerating along the y-axis at a rate of [tex]+2.5\:\text{m/s}^2[/tex] as well as along the x-axis at a rate of [tex]+5.1\:\text{m/s}^2.[/tex] So the magnitude of the box's total acceleration is given by
[tex]a_T = \sqrt{a_x^2 + a_y^2}[/tex]
[tex]\:\:\:\:= \sqrt{(5.1\:\text{m/s}^2)^2 + (2.5\:\text{m/s}^2)^2}[/tex]
[tex]\:\:\:\:=5.7\:\text{m/s}^2[/tex]
The direction of the acceleration [tex]\theta[/tex] with respect to the horizontal direction is given by
[tex]\theta = \tan^{-1}\!\left(\dfrac{a_y}{a_x}\right) = \tan^{-1}\!\left(\dfrac{2.5\:\text{m/s}^2}{5.1\:\text{m/s}^2}\right)[/tex]
[tex]\:\:\:\:= 26.1°[/tex]
A block weighing 400 kg rest on a horizontal surface and supports on top of it another block of weight 100 kg placed on the top of it as shown. The block W2 is attached to a vertical wall by a string 6 m long. Ifthe coefficient of friction between all surfaces is 0.25 and the system is in equilibrium find the magnitude of the horizontal force P applied to the lower block.
The horizontal force applied to the lower block is approximately 1,420.85 Newtons
The known parameters are;
The mass of the block, m₁ = 400 kg, weight, W₁ = 3,924 N
The mass of the block resting on the first block, m₂ = 100 kg, weight, W₂ = 981 N
The length of the string attached to the block, W₂, l = 6 m
The horizontal distance from the point of attachment of the second block to the block W₂, x = 5 m
The coefficient of friction between the surfaces, μ = 0.25
Let T represent the tension in the string
The upward force on W₂ due to the string = T × sin(θ)
The normal force of W₁ on W₂, N₂ = W₂ - T × sin(θ)
The tension in the string, T = N₂ × μ × cos(θ)
∴ T = (W₂ - T × sin(θ)) × μ × cos(θ)
sin(θ) = √(6² - 5²)/6
cos(θ) = 5/6
∴ T = (981 - T × √(6² - 5²)/6) × 0.25 × 5/6
Solving, we get;
T ≈ 183.27 N
The normal reaction on W₂, N₂ = T/(μ × cos(θ))
∴ N₂ = 183.27/(0.25 × 5/6) = 879.7
N₂ ≈ 879.7 N
The friction force, [tex]F_{f2}[/tex] = N₂ × μ
∴ [tex]F_{f2}[/tex] = 879.7 N × 0.25 = 219.925 N
The total normal reaction on the ground, [tex]\mathbf{N_T}[/tex] = W₁ + N₂
[tex]N_T[/tex] = 3,924 N + 879.7 N = 4,803.7 N
The friction force, on the ground [tex]\mathbf{F_T}[/tex] = [tex]\mathbf{N_T}[/tex] × μ
∴ [tex]F_T[/tex] = 4,803.7 N × 0.25 = 1,200.925 N
The horizontal force applied to the lower block, P = [tex]\mathbf{F_T}[/tex] + [tex]\mathbf{F_{f2}}[/tex]
Therefore;
P = 1,200.925 N + 219.925 N = 1,420.85 N
The horizontal force applied to the lower block, P ≈ 1,420.85 N
A uniform magnetic field passes through a horizontal circular wire loop at an angle 15.1° from the normal to the plane of the loop. The magnitude of the magnetic field is 3.35 T , and the radius of the wire loop is 0.240 m . Find the magnetic flux Φ through the loop.
Answer:
0.5849Weber
Explanation:
The formula for calculating the magnetic flus is expressed as:
[tex]\phi = BAcos \theta[/tex]
Given
The magnitude of the magnetic field B = 3.35T
Area of the loop = πr² = 3.14(0.24)² = 0.180864m²
angle of the wire loop θ = 15.1°
Substitute the given values into the formula:
[tex]\phi = 3.35(0.180864)cos15.1^0\\\phi =0.6058944cos15.1^0\\\phi =0.6058944(0.9655)\\\phi = 0.5849Wb[/tex]
Hence the magnetic flux Φ through the loop is 0.5849Weber
You are working on a project to make a more efficient engine. Your team is investigating the possibility of making electrically controlled valves that open and close the input and exhaust openings for an internal combustion engine. Determine the stability of the valve by calculating the force on each of its sides and the net force on the valve.
The valve is made of a thin but strong rectangular piece of non-magnetic material that has a current-carrying wire along its edges. The rectangle is 0.35 cm x 1.83 cm. The valve is placed in a uniform magnetic field of 0.15 T such that the field lies in the plane of the valve and is parallel to the short sides of the rectangle. The region with the magnetic field is slightly larger than the valve. When a switch is closed, a 1.7 A current enters the short side of the rectangle on one side and leaves on the opposite short side of the rectangle. At the suggestion of a colleague, who is hoping to ensure different currents along the sides of the valve, resistors have been included along the wire on each of the short sides of the valve. The value of the resistor on one side is twice that on the other side.
Answer:
The answer is "0.00466 N".
Explanation:
[tex]F=(B \times i) L\\\\[/tex]
therefore the smaller side is parallel to magnetic field
[tex]\therefore \\\\F= B i L\ \sin\ 'o'=0 \ N[/tex]
calculating the force on the layer side:
[tex]\to F=0.15 \times 1.7 \times 0.0183 \times \sin 90^{\circ}=0.00466\ N\\\\[/tex]
Therefore [tex]F_o[/tex] the net force on the rectangular loop [tex]= 0.00466 \ N[/tex]
A Ball A and a Ball B collide elastically. The initial momentum of Ball A is -2.00kgm/s and the initial momentum of Ball B is -5.00kgm/s. Ball A has a mass of 4.00kg and is traveling at 2.50 m/s after the collision. What is the velocity of ball B if it has a mass of 6.50kg?
The velocity of B after the collision is obtained as -2.6 m/s.
What is the principle of conservation of momentum?Now we now that the principle of conservation of momentum states that the momentum before collision is equal to the momentum after collision.
Thus;
(-2.00kgm/s) + ( -5.00kgm/s) = ( 4.00kg * 2.50 m/s) + ( 6.50kg * v)
-7 = 10 + 6.5v
-7 - 10 = 6.5v
v = -7 - 10 /6.5
v = -2.6 m/s
Hence, the velocity of B after the collision is obtained as -2.6 m/s.
Learn more about elastic collision:https://brainly.com/question/5719643
#SPJ1
Find the intensity of the electromagnetic wave described in each case. (a) an electromagnetic wave with a wavelength of 655 nm and a peak electric field magnitude of 1.5 V/m. 0.002984 W/m2 (b) an electromagnetic wave with an angular frequency of 6.5 ✕ 1018 rad/s and a peak magnetic field magnitude of 10−10 T. 1.19366E-6 W/m2
The intensity of the electromagnetic wave in terms of the electric field is 0.00298 W/m² and the intensity of the electromagnetic wave in terms of the magnetic field is 1.193x10⁻⁶ W/m².
The intensity of the electromagnetic wave is related to the electric field as well as to the magnetic field.
a) Intensity of the electromagnetic wave for the electromagnetic field.
The intensity of the electromagnetic wave (I) in terms of the electromagnetic field is given by:
[tex] I = \frac{E^{2}*c*\epsilon_{0}}{2} [/tex] (1)
Where:
c: is the speed of light = 3.00*10⁸ m/s
E: is the magnitude of the electric field = 1.5 V/m
ε₀: is the permittivity of free space = 8.85*10⁻¹² C²/Nm²
Hence, the intensity of the electromagnetic wave (eq 1) is:
[tex] I = \frac{(1.5 V/m)^{2}*3.00 \cdot 10^{8} m/s*8.85 \cdot 10^{-12} C^{2}/(N*m^{2})}{2} = 0.00298 W/m^{2} [/tex]
b) Intensity of the electromagnetic wave for the magnetic field
We can calculate the intensity of the electromagnetic wave (I) in terms of the magnetic field with the following equation:
[tex] I = \frac{cB^{2}}{2\mu_{0}} [/tex] (2)
Where:
B: is the magnitude of the magnetic field = 10⁻¹⁰ T
μ₀: is the vacuum permeability = 4π*10⁻⁷ m*T/A
Therefore, the intensity of the electromagnetic wave (eq 2) is:
[tex] I = \frac{3.00 \cdot 10^{8} m/s*(1\cdot 10^{-10} m*T/A)^{2}}{2*4\pi \cdot 10^{-7} T/A} = 1.193 \cdot 10^{-6} W/m^{2} [/tex]
Learn more about electromagnetic waves and magnetic and electric fields here: https://brainly.com/question/11647801?referrer=searchResults
I hope it helps you!
The source of sound moves away from the listener.The listener has the impression that the source is lower in pitch. Why?
When the source is moving away from the observer the velocity of the source is added to the speed of light. This increases the value of the denominator, decreasing the value of the observed frequency. Frequency corresponds to pitch or tone; a lower observed frequency will result in a lower observed pitch.
Hi Friends!
please help me with these questions!
SUBJECT: Chemistry, Physics,Biology
Answer:
q.1 : Air near candle gets heated up and after this it rises by convection so the thermometer B will receive more heat than the thermometer A So, according to the given condition thermometer B will show a greater rise in temperature.
q.2 : x is the pure sample of compound . y is the pure sample of element . z is the mixture of different elements
q.3 : the saliva contains an enzyme salivary amylase (ptyalin) which converts starch in roti into maltose, isomaltose and small dextrins called a-dextrin.
the number of significant figures in the measurement 4.300×10^5 km are
Answer:
6
Explanation
Any numbers in scientific notation are considered significant. For example, 4.300 x 10-4 has 4 significant figures.
Answer From Gauth Math
The "Pressure" meter allows you to read the pressure at different depths in the fluid. Place the pressure meter close to the bottom of the pool, and read the pressure. Slowly move the pressure meter toward the surface of the water in the pool and read the pressure at different depths in the pool. What happens to pressure in the fluid as the depth of the fluid decreases?
Answer:
The pressure near the surface of the pool will be less as compared that the bottom of the pool as water has weight. This is in relation to gravity
Explanation:
There is a relationship between volume and pressure. The increase in depth leads to an increase in volume and an increase in the force of gravity near the surface as compared to lifting and rising light pressure as light air rises and heavy air sinks.The graph below shows a cycle of a heat engine. Add the following labels to the graph. Some labels are used more than once.
Labels: Isobaric process; W= 0J; Work done on the system; Work done by the system.
I will give brainliest!
P.S. AL2006 if you see this please help!
I'm not very good at this material. I'll try it, but if I were you, I wouldn't bet money on these answers.
"Isobaric" means constant pressure. So those are the horizontal lines, where every point on the line is at the same pressure. Those are the processes 1>2 and 3>4 .
I'm going around and around in my mind with the other labels, and I can't decide. So I'm afraid I can't answer any more of them ... they might be wrong.
Answer:
1 -> 2 & 3 -> 4: Isobaric process
4 -> 1: Work done BY the system
2 -> 3: Work done ON the system
W(total): W = 0J
Explanation:
The two horizontal lines (1 -> 2 & 3 -> 4) are "Isobaric" since isobaric processes take place at constant pressure. I believe 4 -> 1 is "Work done BY the system" since pressure increases when there is an increase of thermal energy, in other words, the system is absorbing heat. This is why the volume increases from 1 -> 2 after the system has absorbed heat in 4 -> 1. Following the directions of the arrows, 2 -> 3 would be "Work done ON the system" since pressure is DECREASING, meaning temperature is also exiting the system. That's why the next step (3 -> 4) shows a decrease in volume. This model depicts a process that has a W(total) of 0 J because this is a cycle.
I hope this helps :))
A bicycle tire with a volume of 0.00210 m^3 is filled to its recommended absolute pressure of 495 kPa on a cold winter day when the tire's temperature is -14°C. The cyclist then brings his bicycle into a hot laundry room at 32°C.
a. If the tire warms up while its volume remains constant, will the pressure increase be greater than, less than, or equal to the manufacturer's stated 10% overpressure limit?
b. Find the absolute pressure in the tire when it warms to 32 degrees Celcius at constant volume.
(A) The pressure will be greater than 10% overpressure limit.
(B) The final pressure will be "582.915 kPa".
Given:
Volume,
[tex]V = 0.0021 \ m^3[/tex]Initial pressure,
[tex]P_o= 495 \ kPa[/tex]Initial temperature,
[tex]T_o = -14^{\circ} C[/tex][tex]= 259 \ K[/tex]
Final temperature,
[tex]T = 32^{\circ} C[/tex](B)
Number of moles,
→ [tex]n = (\frac{P_o V}{RT_o} )[/tex]
then,
The final absolute pressure,
→ [tex]P = \frac{nRT}{V}[/tex]
[tex]= (\frac{P_o V}{RT_o} )(\frac{RT}{V} )[/tex]
[tex]=(\frac{T}{T_o} )P_o[/tex]
[tex]= (\frac{305}{259} )\times 495[/tex]
[tex]= 582.915 \ kPa[/tex]
Thus the above approach is correct.
Learn more:
https://brainly.com/question/13033911
Consider the nearly circular orbit of Earth around the Sun as seen by a distant observer standing in the plane of the orbit. What is the effective "spring constant" of this simple harmonic motion?
Express your answer to three significant digits and include the appropriate units.
We have that the spring constant is mathematically given as
[tex]k=2.37*10^{11}N/m[/tex]
Generally, the equation for angular velocity is mathematically given by
[tex]\omega=\sqrt{k}{m}[/tex]
Where
k=spring constant
And
[tex]\omega =\frac{2\pi}{T}[/tex]
Therefore
[tex]\frac{2\pi}{T}=\sqrt{k}{n}[/tex]
Hence giving spring constant k
[tex]k=m((\frac{2 \pi}{T})^2[/tex]
Generally
Mass of earth [tex]m=5.97*10^{24}[/tex]
Period for on complete resolution of Earth around the Sun
[tex]T=365 days[/tex]
[tex]T=365*24*3600[/tex]
Therefore
[tex]k=(5.97*10^{24})((\frac{2 \pi}{365*24*3600})^2[/tex]
[tex]k=2.37*10^{11}N/m[/tex]
In conclusion
The effective spring constant of this simple harmonic motion is
[tex]k=2.37*10^{11}N/m[/tex]
For more information on this visit
https://brainly.com/question/14159361
a stone is thrown vertically upwards with a velocity of 20 m per second what will be its velocity when it reaches a height of 10.2 m
Answer:
Explanation:
Here's the info we have:
initial velocity is 20 m/s;
final velocity is our unknown;
displacement is -10.2 m; and
acceleration due to gravity is -9.8 m/s/s. Using the one-dimensional equation
v² = v₀² + 2aΔx and filling in accordingly to solve for v:
[tex]v=\sqrt{(20)^2+2(-9.8)(-10.2)}[/tex] Rounding to the correct number of sig fig's to simplify:
[tex]v=\sqrt{400+2.0*10^2}[/tex] to get
v = [tex]\sqrt{600}=20\frac{m}{s}[/tex] If you don't round like that, the velocity could be 24, or it could also be 24.5 depending on how your class is paying attention to sig figs or if you are at all.
So either 20 m/s or 24 m/s
PLEASE ANSWER IF YOU CAN AND NOT FOR THE SAKE OF GAINING POINTS!
find the rate of energy radiated by a man by assuming the surface area of his body 1.7m²and emissivity of his body 0.4
The rate of energy radiated by the man is 3.86 x [tex]10^{-8}[/tex] J/s. [tex]m^{2}[/tex].
The amount of energy radiated by an object majorly depends on the area of its surface and its temperature. The is well explained in the Stefan-Boltzmann's law which states that:
Q(t) = Aeσ[tex]T^{4}[/tex]
where: Q is the quantity of heat radiated, A is the surface area of the object, e is the emmisivity of the object, σ is the Stefan-Boltzmann constant and T is the temperature of the object.
To determine the rate of energy radiated by the man in the given question;
[tex]\frac{Q(t)}{T^{4} }[/tex] = Aeσ
But A = 1.7 m², e = 0.4 and σ = 5.67 x [tex]10^{-8}[/tex] J/s.
So that;
[tex]\frac{Q(t)}{T^{4} }[/tex] = 1.7 * 0.4 * 5.67 x [tex]10^{-8}[/tex]
= 3.8556 x [tex]10^{-8}[/tex]
= 3.86 x [tex]10^{-8}[/tex] J/s. [tex]m^{2}[/tex]
Thus, the rate of energy radiated by the man is 3.86 x [tex]10^{-8}[/tex] J/s. [tex]m^{2}[/tex].
Learn more on energy radiation of objects by visiting: https://brainly.com/question/12550129
define nortons theorem
Answer:
In direct-current circuit theory, Norton's theorem is a simplification that can be applied to networks made of linear time-invariant resistances, voltage sources, and current sources. At a pair of terminals of the network, it can be replaced by a current source and a single resistor in parallel.
Una persona de 76 kg está siendo retirada de un edificio en llamas mientras se muestra en la figura. Calcule la tensión
en las dos cuerdas si la persona está momentáneamente inmovil.
Ayuda por favor.
Answer:
T1 = 736.6 N, T2 = 193.5 N
Explanation:
W = 76 N
The tension is T1 and T2.
By use of Lami's theorem
[tex]\frac{T_1}{Sin100}=\frac{T_2}{Sin165}=\frac{W}{Sin 95}\\\\So, \\\\T_1 = \frac{76\times 9.8\times Sin 100}{Sin 95} = 736.6 N \\And\\T_2 = \frac{76\times 9.8\times Sin 165}{Sin 95} = 193.5 N \\[/tex]
5. A bicyclist is finishing her repair of a flat tire when a friend rides by at a constant velocity of
3.5 m/s. Three seconds later, the bicyclist hops on her bike and accelerates at 3.6 m/s² until she
catches her friend.
a. How much time does it take until she catches her friend?
b. How far has she traveled in this time?
c. What is her speed when she catches up?
Answer:
a) t = 3.6 s
b) d = 23 m
c) v = 13 m/s
Explanation:
Let t be the time the accelerating rider rides
the distance she travels is
d = ½3.6t²
the distance for the other cyclist is
d =3.5(t + 3)
½3.6t² = 3.5(t + 3)
1.8t² - 3.5t - 10.5 = 0
quadratic formula, positive answer
t = (3.5 + √(3.5² - 4(1.8)(-10.5))) / (2(1.8))
t = 3.575786...
d = ½(3.6)(3.575786²) = 23.015...
v = 3.6(3.575786) = 12.8728...
Which of the following choices is not an example of climate?
0000
San Diego has mild, warm temperatures and sea breezes year-round.
Anchorage has short, cool summers and long, snowy winters.
It will be 78° on Friday in Clovis.
Florida is tropical, with a significant rainy season.
Answer:
Florida is tropical, with a significant rainy seson
A nearsighted person has a near point of 50 cmcm and a far point of 100 cmcm. Part A What power lens is necessary to correct this person's vision to allow her to see distant objects
Answer:
P = -1 D
Explanation:
For this exercise we must use the equation of the constructor
/ f = 1 / p + 1 / q
where f is the focal length, p and q is the distance to the object and the image, respectively
The far view point is at p =∞ and its image must be at q = -100 cm = 1 m, the negative sign is because the image is on the same side as the image
[tex]\frac{1}{f} = \frac{1}{infinity} + \frac{1}{-1}[/tex]
f = 1 m
P = 1/f
P = -1 D
What is an internal resistance?
Explanation:
some thing inside a resistor
Mention the importance of occupation??
Answer:
ln the contemporary time , farming can be considered as comparitively important occupation as it can feed the population , So agriculture is having a greater importance than any other occupation.
Which questions would a biopsychologist most likely address when studying depression?
A bio psychologist would address questions on stress, abuse and conflict when studying depression.
A bio psychologist is a person that is involved in the study of the brain and peoples behavior. This person tries to understand why people do the things or act the way they do using a biological and psychological approach.
While trying to understand the cause of this depression, the bio psychologist would
ask to know if the subject is undergoing stressful situationsIf an abuse led to the situation. It could be physical, emotional or mental abuse. Another question would be if a conflict or altercation caused it.read more on
https://brainly.com/question/17343378?referrer=searchResults
Let A^=6i^+4j^_2k^ and B= 2i^_2j^+3k^. find the sum and difference of A and B
Explanation:
Let [tex]\textbf{A} = 6\hat{\textbf{i}} + 4\hat{\textbf{j}} - 2\hat{\textbf{k}}[/tex] and [tex]\textbf{B} = 2\hat{\textbf{i}} - 2\hat{\textbf{j}} + 3\hat{\textbf{k}}[/tex]
The sum of the two vectors is
[tex]\textbf{A + B} = (6 + 2)\hat{\textbf{i}} + (4 - 2)\hat{\textbf{j}} + (-2 + 3)\hat{\textbf{k}}[/tex]
[tex] = 8\hat{\textbf{i}} + 2\hat{\textbf{j}} + \hat{\textbf{k}}[/tex]
The difference between the two vectors can be written as
[tex]\textbf{A - B} = (6 - 2)\hat{\textbf{i}} + (4 - (-2))\hat{\textbf{j}} + (-2 - 3)\hat{\textbf{k}}[/tex]
[tex]= 4\hat{\textbf{i}} + 6\hat{\textbf{j}} - 5\hat{\textbf{k}}[/tex]
Is it true that as we gain mass the force of gravity on us decreases
Answer:
No. As we gain mass the force of gravity on us does not decrease
These capacitors are then disconnected from their batteries, and the positive plates are now connected to each other and the negative plates are connected to each other. What will be the potential difference across each capacitor
Answer:
Following are the solution to the given question:
Explanation:
For charging plates that are connected in a similar manner:
Calculating the total charge:
[tex]\to q =q_1 + q_2 = C_1V_1 +C_2V_2 =1320 + 2714 = 4034 \mu C[/tex]
Calculating the common potential:
[tex]\to V = \frac{q}{C}= \frac{q}{(C_1 + C_2)} =\frac{4034}{6.8} = 593 \ V\\\\[/tex]
Calculating the charge after redistribution:
[tex]When: \\\\q = q_{1}' + q_{2}' = q_1 + q_2[/tex]
[tex]\to q_{1}' = C_1V = 2.2 \times 593 = 1305\ \mu C\\ \\ \to q_{2}' = C_2V = 4.6 \times 593 = 2729 \ \mu C[/tex]
Determine usando ecuación de Bernoulli la Presión P1 necesaria para mantener la condición mostrada dentro del sistema mostrado en la figura, sabiendo que el aceite tiene un s.g =0.45 y el valor de d=90mm.
Answer:
PlROCA
Explanation:
Determine the density in kg \cm of solid whose Made is 1080 and whose dimension in cm are length=3 ,width=4,and height=3
Answer:
d = 30kg/cm³
Explanation:
d = m/v
d = 1080kg/(3cm*4cm*3cm)
d = 30kg/cm³
