Some radar systems detect the size and shape of objects such as aircraft and geological terrain. Approximately what is the smallest observable detail (in m) utilizing 495 MHz radar?

Answers

Answer 1

Answer:

0.61 m

Explanation:

The smallest observable length by the radar must be at least equal to or greater than the wavelength of the radar.

using the relationship

c = fλ

where

c is the speed of light in vacuum = 3 x 10^8 m/s

f is the frequency of the wave = 495 MHz = 4.95 x 10^8 Hz

λ is the wavelength = ?

λ = c/f = (3 x 10^8)/(4.95 x 10^8) = 0.61 m

Answer 2

answer to your question is 0.6m


Related Questions

A mass M is attached to an ideal massless spring. When this system is set in motion with amplitude A, it has a period T. What is the period if the amplitude of the motion is doubled

Answers

Answer:

The period of the motion will still be equal to T.

Explanation:

for a system with mass = M

attached to a massless spring.

If the system is set in motion with an amplitude (distance from equilibrium position) A

and has period T

The equation for the period T is given as

[tex]T = 2\pi \sqrt{\frac{M}{k} }[/tex]

where k is the spring constant

If the amplitude is doubled, the distance from equilibrium position to the displacement is doubled.

Increasing the amplitude also increases the restoring force. An increase in the restoring force means the mass is now accelerated to cover more distance in the same period, so the restoring force cancels the effect of the increase in amplitude. Hence, increasing the amplitude has no effect on the period of the mass and spring system.

A circular loop in the plane of a paper lies in a 0.45 T magnetic field pointing into the paper. The loop's diameter changes from 17.0 cm to 6.0 cm in 0.53 s.
A) Determine the direction of the induced current.
B) Determine the magnitude of the average induced emf.
C) If the coil resistance is 2.5 Ω, what is the average induced current?

Answers

Answer:

(A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

Explanation:

Given that,

Magnetic field = 0.45 T

The loop's diameter changes from 17.0 cm to 6.0 cm .

Time = 0.53 sec

(A). We need to find the direction of the induced current.

Using Lenz law

If the direction of magnetic field shows into the paper then the direction of the induced current will be clockwise.

(B). We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{1}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{1}=0.45\times(\pi\times(8.5\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{1}=0.01021\ Wb[/tex]

We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{2}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{2}=0.45\times(\pi\times(3\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{2}=0.00127\ Wb[/tex]

We need to calculate the magnitude of the average induced emf

Using formula of emf

[tex]\epsilon=-N(\dfrac{\Delta \phi}{\Delta t})[/tex]

Put the value into t5he formula

[tex]\epsilon=-1\times(\dfrac{0.00127-0.01021}{0.53})[/tex]

[tex]\epsilon=0.016867\ V[/tex]

[tex]\epsilon=16.87\ mV[/tex]

(C). If the coil resistance is 2.5 Ω.

We need to calculate the induced current

Using formula of current

[tex]I=\dfrac{\epsilon}{R}[/tex]

Put the value into the formula

[tex]I=\dfrac{0.016867}{2.5}[/tex]

[tex]I=0.00675\ A[/tex]

[tex]I=6.75\ mA[/tex]

Hence, (A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

A speeding car has a velocity of 80 mph; suddenly it passes a cop car but does not stop. When the speeding car passes the cop car, the cop immediately accelerates his vehicle from 0 to 90 mph in 4.5 seconds. The cop car has a maximum velocity of 90 mph. At what time does the cop car meet the speeding car and at what distance?

Answers

Answer:

Distance= 4 miles

Time = 36.3 seconds

Explanation:

80 mph = 178.95 m/s

90 mph = 201.32 m/s

V = u +at

201.32= 0+a(4.5)

201.32/4.5= a

44.738 m/s² = a

Acceleration of the cop car

= 44.738 m/s²

Distance traveled at 4.5seconds

For the cop car

S= ut + ½at²

S= 0(4.5) + ½*44.738*4.5

S= 100.66 meters

Distance traveled at 4.5seconds

For the speeding car

4.5*178.95=805.275

The cop car will still cover 704.675 +x distance while the speeding car covers for their distance to be equal

X/178.95= (704.675+x)/201.32

X-0.89x= 626.37

0.11x= 626.37

X= 5694.3 meters

The time = 5694.3/178.95

Time =31.8 seconds

So the distance they meet

= 5694.3+805.275

= 6499.575 meters

= 4.0 miles

The Time = 4.5+31.8

Time = 36.3 seconds

A student holds a bike wheel and starts it spinning with an initial angular speed of 7.0 rotations per second. The wheel is subject to some friction, so it gradually slows down.

In the 10.0 s period following the inital spin, the bike wheel undergoes 60.0 complete rotations. Assuming the frictional torque remains constant, how much more time Δ????s will it take the bike wheel to come to a complete stop?

The bike wheel has a mass of 0.625 kg0.625 kg and a radius of 0.315 m0.315 m. If all the mass of the wheel is assumed to be located on the rim, find the magnitude of the frictional torque ????fτf that was acting on the spinning wheel.

Answers

Answer:

a)   Δt = 24.96 s , b)  τ = 0.078 N m

Explanation:

This is a rotational kinematics exercise

        θ = w₀ t - ½ α t²

Let's reduce the magnitudes the SI system

       θ = 60 rev (2π rad / 1 rev) = 376.99 rad

       w₀ = 7.0 rot / s (2π rad / 1 rpt) = 43.98 rad / s

       

      α = (w₀ t - θ) 2 / t²

let's calculate the annular acceleration

      α = (43.98 10 - 376.99) 2/10²

      α = 1,258 rad / s²

Let's find the time it takes to reach zero angular velocity (w = 0)

        w = w₀ - alf t

         t = (w₀ - 0) / α

         t = 43.98 / 1.258

         t = 34.96 s

this is the total time, the time remaining is

         Δt = t-10

         Δt = 24.96 s

To find the braking torque, we use Newton's law for angular motion

        τ = I α

the moment of inertia of a circular ring is

       I = M r²

we substitute

         τ = M r² α

we calculate

        τ = 0.625  0.315²  1.258

        τ = 0.078 N m

The total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Given data:

The initial angular speed of wheel is, [tex]\omega = 7.0 \;\rm rps[/tex]   (rps means rotation per second).

The time interval is, t' = 10.0 s.

The number of rotations made by wheel is, n = 60.0.

The mass of bike wheel is, m = 0.625 kg.

The radius of wheel is, r = 0.315 m.

The problem is based on rotational kinematics. So, apply the second rotational equation of motion as,

[tex]\theta = \omega t-\dfrac{1}{2} \alpha t'^{2}[/tex]

Here, [tex]\theta[/tex] is the angular displacement, and its value is,

[tex]\theta =2\pi \times 60\\\\\theta = 376.99 \;\rm rad[/tex]

And, angular speed is,

[tex]\omega = 2\pi n\\\omega = 2\pi \times 7\\\omega = 43.98 \;\rm rad/s[/tex]

Solving as,

[tex]376.99 = 43.98 \times 10-\dfrac{1}{2} \alpha \times 10^{2}\\\\\alpha = 1.25 \;\rm rad/s^{2}[/tex]

Apply the first rotational equation of motion to obtain the value of time to reach zero final velocity.

[tex]\omega' = \omega - \alpha t\\\\0 = 43.98 - 1.25 \times t\\\\t = 35.18 \;\rm s[/tex]

Then total time is,

T = t - t'

T = 35.18 - 10

T = 25.18 s

Now, use the standard formula to obtain the value of braking torque as,

[tex]T = m r^{2} \alpha\\\\T = 0.625 \times (0.315)^{2} \times 1.25\\\\T = 0.0775 \;\rm Nm[/tex]

Thus, we can conclude that the total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Learn more about the rotational motion here:

https://brainly.com/question/1388042

When using science to investigate physical phenomena, which characteristic of the event must exist? predictable repeatable provable readable

Answers

Answer:

Not sure but I believe predictable.

Explanation:

Phenomena usually consists of :

- A history, a date in which the physical phenomenon has occurred.

- A source, a place or reason to why or where the physical phenomena has occured.

According to this, I want to say predictable.

It is not repeatable, there are one-time phenomenons that have occurred that scientists to this day still have not recorded again such as the Big Bang.

It is not provable. Most of the theories earlier scientists and historians have predicted have not yet been proved. Yet rather, somehow, they have been explored and investigated.

It is not readable. This is self explanatory, some things scientists investigate are not written down, nor read. It starts with a mental theory and then immediately goes to the next phase of investigation.

On a separate sheet of paper, tell why scientists in different countries can easily compare the amount of matter in similar objects in their countries

Answers

Answer: no u

Explanation: no u

A cook preparing a meal for a group of people is an example of
O kinetic energy because he has the ability to make a meal
O potential energy because he has the ability to make a meal
O kinetic energy because he is making the meal
o potential energy because he is making the meal​

Answers

The third point is the correct answer because it’s happening now and kinetic energy is energy possessed by a moving object.

Hope this helps ya

A long solenoid consists of 1700 turns and has a length of 0.75 m.The current in the wire is 0.48 A. What is the magnitude of the magnetic field inside the solenoid

Answers

Answer:

1.37 ×10^-3 T

Explanation:

From;

B= μnI

μ = 4π x 10-7 N/A2

n= number of turns /length of wire = 1700/0.75 = 2266.67

I= 0.48 A

Hence;

B= 4π x 10^-7 × 2266.67 ×0.48

B= 1.37 ×10^-3 T

When the adjustable mirror on the Michelson interferometer is moved 20 wavelengths, how many fringe pattern shifts would be counted

Answers

Answer:

The number of  fringe pattern shift is   m  = 40

Explanation:

 From the question we are told that

      The  Michelson interferometer is moved 20 wavelengths i.e  [tex]20 \lambda[/tex]

Generally the distance which the  Michelson interferometer is moved is mathematically represented as

         [tex]d = \frac{m * \lambda}{2}[/tex]

Here [tex]m[/tex] is the number of  fringe pattern shift

     So

         [tex]20 \lambda = \frac{m * \lambda}{2}[/tex]

         [tex]40 \lambda = m * \lambda[/tex]

        m  = 40

c) If the ice block (no penguins) is pressed down even with the surface and then released, it will bounce up and down, until friction causes it to settle back to the equilibrium position. Ignoring friction, what maximum height will it reach above the surface

Answers

Answer:

y = 20.99 V / A

there is no friction    y = 20.99 h

Explanation:

Let's solve this exercise in parts: first find the thrust on the block when it is submerged and then use the conservation of energy

when the block of ice is submerged it is subjected to two forces its weight  hydrostatic thrust

         

              F_net= ∑F = B-W

the expression stop pushing is

              B = ρ_water g V_ice

where rho_water is the density of pure water that we take as 1 10³ kg / m³ and V is the volume d of the submerged ice

We can write the weight of the body as a function of its density rho_hielo = 0.913 10³ kg / m³

             W = ρ-ice g V

              F_net = (ρ_water - ρ_ ice) g V

this is the net force directed upwards, we can find the potential energy with the expression

            F = -dU / dy

            ΔU = - ∫ F dy

            ΔU = - (ρ_water - ρ_ ice) g ∫ (A dy) dy

            ΔU = - (ρ_water - ρ_ ice) g A y² / 2

we evaluate between the limits y = 0,  U = 0, that is, the potential energy is zero at the surface

             U_ice = (ρ_water - ρ_ ice) g A y² / 2

now we can use the conservation of mechanical energy

starting point. Ice depth point

             Em₀ = U_ice = (ρ_water - ρ_ ice) g A y² / 2

final point. Highest point of the block

             [tex]Em_{f}[/tex] = U = m g y

as there is no friction, energy is conserved

            Em₀ = Em_{f}

            (ρ_water - ρ_ ice) g A y² / 2 = mg y

let's write the weight of the block as a function of its density

            ρ_ice = m / V

            m = ρ_ice V

we substitute

             (ρ_water - ρ_ ice) g A y² / 2 = ρ_ice V g y

              y = ρ_ice / (ρ_water - ρ_ ice) 2 V / A

let's substitute the values

             y = 0.913 / (1 - 0.913) 2 V / A

             y = 20.99 V / A

This is the height that the lower part of the block rises in the air, we see that it depends on the relationship between volume and area, which gives great influence if there is friction, as in this case it is indicated that there is no friction

                V / A = h

where h is the height of the block

                 y = 20.99 h

What is the de Broglie wavelength of an object with a mass of 2.50 kg moving at a speed of 2.70 m/s? (Useful constant: h = 6.63×10-34 Js.)

Answers

Answer:

9.82 × [tex]10^{-35}[/tex] Hz

Explanation:

De Broglie equation is used to determine the wavelength of a particle (e.g electron) in motion. It is given as:

λ = [tex]\frac{h}{mv}[/tex]

where: λ is the required wavelength of the moving electron, h is the Planck's constant, m is the mass of the particle, v is its speed.

Given that: h = 6.63 ×[tex]10^{-34}[/tex] Js, m = 2.50 kg, v = 2.70 m/s, the wavelength, λ, can be determined as follows;

λ = [tex]\frac{h}{mv}[/tex]

  = [tex]\frac{6.63*10^{-34} }{2.5*2.7}[/tex]

 = [tex]\frac{6.63 * 10^{-34} }{6.75}[/tex]

 = 9.8222 × [tex]10^{-35}[/tex]

The wavelength of the object is 9.82 × [tex]10^{-35}[/tex] Hz.

The A block, with negligible dimensions and weight P, is supported by the coordinate point (1.1/2) of the parabolic fixed grounded surface, from equation y = x^2/2 If the block is about to slide, what is the coefficient of friction between it and the surface; determine the force F tangent to the surface, which must be applied to the block to start the upward movement.

Answers

Answer:

μ = 1

F = P√2

Explanation:

The parabola equation is: y = ½ x².

The slope of the tangent is dy/dx = x.

The angle between the tangent and the x-axis is θ = tan⁻¹(x).

At x = 1, θ = 45°.

Draw a free body diagram of the block.  There are three forces:

Weight force P pulling down,

Normal force N pushing perpendicular to the surface,

and friction force Nμ pushing up tangential to the surface.

Sum of forces in the perpendicular direction:

∑F = ma

N − P cos 45° = 0

N = P cos 45°

Sum of forces in the tangential direction:

∑F = ma

Nμ − P sin 45° = 0

Nμ = P sin 45°

μ = P sin 45° / N

μ = tan 45°

μ = 1

Draw a new free body diagram.  This time, friction force points down tangential to the surface, and applied force F pushes up tangential to the surface.

Sum of forces in the tangential direction:

∑F = ma

F − Nμ − P sin 45° = 0

F = Nμ + P sin 45°

F = (P cos 45°) μ + P sin 45°

F = P√2

A jumbo jet has a mass of 100,000 kg. The thrust of each of its four engines is 50,000 N. What is the jet's acceleration in meters per second squared right before taking off? Neglect air resistance and friction.

Answers

Answer:

The acceleration is   [tex]a =2\ m/s^2[/tex]

Explanation:

From the question we are told that

       The  mass of the jumbo jet is  [tex]m_j = 100000\ kg[/tex]

        The thrust is  [tex]F_k = 50000 \ N[/tex]

Generally given that the jet has four engines the total thrust is  

        [tex]F_t = 4 * F_k[/tex]

substituting values

       [tex]F_t = 4 * 50000[/tex]

      [tex]F_t = 200000 \ N[/tex]

Generally the acceleration of the is mathematically represented as

         [tex]a = \frac{F_t}{m}[/tex]

substituting values

       [tex]a =2 \frac{N}{kg}[/tex]

Now  

        [tex]N = kg \cdot m/s^2[/tex]

Hence

         [tex]a =2 \frac{kg * \cdot m/s^2}{kg}[/tex]

        [tex]a =2\ m/s^2[/tex]

a person Travels along a straight road for half the distance with velocity V1 and the remaining half the distance with velocity V2 the average velocity is given by​

Answers

Answer: (V1+V2)/2

Explanation: This is because basically with the question they are trying to say u(initial velocity) is V1 and v(final velocity) is V2 as the journey starts off with V1 and ends with V2 so therefore we know an equation where average velocity=(u+v)/2. So here it’s (V1+V2)/2

In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?

Answers

Answer:

The wavelength is  [tex]\lambda = 419 \ nm[/tex]

Explanation:

From the question we are told that

   The  distance of separation is   [tex]d = 3.34 *10^{-5} \ m[/tex]

   The  distance of the screen is  [tex]D = 3.30 \ m[/tex]

      The  order of the fringe is  n =  7

     The distance of separation of  fringes is y =  29.0 cm = 0.29 m

   

Generally the wavelength of the light is mathematically represented as

          [tex]\lambda = \frac{y * d }{ n * D}[/tex]

substituting values

         [tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]

        [tex]\lambda = 4.19*10^{-7}\ m[/tex]

        [tex]\lambda = 419 \ nm[/tex]

Find the focal length of contact lenses that would allow a nearsighted person with a 130 cmcm far point to focus on the stars at night.

Answers

Answer:

130cm

Explanation:

The lens equation is expressed as;

1/f = 1/u+1/v where;

f is the focal length of the lens

u is the object distance

v is the image distance

Since the near sighted person wants focus the starts at nigt, the stars at night are the images located that infinity. Hence the image distance v = ∞.

The object distance u = 130cm

Substituting the given parameters in the formula to get the focal length f

[tex]\frac{1}{f} = \frac{1}{\infty} + \frac{1}{130} \\\\As \ x \ tends \ to \ \infty, \, \frac{a}{x} \ tends \ to \ 0 \ where\ 'a' \ is \ a\ constant \\\\} \\\\[/tex]

[tex]\frac{1}{f} = 0+ \frac{1}{130}\\\\[/tex]

[tex]\frac{1}{f} =\frac{1}{130}\\cross\ multiply\\\\f = 130*1\\\\f = 130cm[/tex]

Hence the focal length of contact lenses that would allow a nearsighted person with a 130 cm far point to focus on the stars at night is 130cm

Niobium metal becomes a superconductor when cooled below 9 K. Its superconductivity is destroyed when the surface magnetic field exceeds 0.100 T. In the absence of any external magnetic field, determine the maximum current a 5.68-mm-diameter niobium wire can carry and remain superconducting.

Answers

Answer:

The current is  [tex]I = 1420 \ A[/tex]

Explanation:

From the question we are told that

   The  diameter of the wire is  [tex]d = 5.68 \ mm = 0.00568 \ m[/tex]

    The  magnetic field is  [tex]B = 0.100 \ T[/tex]

   

Generally the radius of the wire is mathematically evaluated as

       [tex]r = \frac{d}{2}[/tex]

substituting values

     [tex]r = \frac{ 0.00568}{2}[/tex]

     [tex]r = 0.00284 \ m[/tex]

Generally the magnetic field is mathematically represented as

       [tex]B = \frac{\mu_o * I}{ 2 \pi r }[/tex]

=>    [tex]I =\frac{ B * 2 \pi r }{\mu_o}[/tex]

Here [tex]\mu_o[/tex] is the permeability of free space  with value [tex]\mu_o = 4 \pi *10^{-7} N/A^2[/tex]

substituting values

=>     [tex]I =\frac{ 0.100 * 2 * 3.142 * 0.00284 }{ 4 \pi * 10^{-7}}[/tex]

=>     [tex]I = 1420 \ A[/tex]

A certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied. In approximately what distance would the car stop had it been going 66.0mph

Answers

Answer: 156.02 metre.

Explanation:

Give that a certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied.

Let us use third equation of motion,

V^2 = U^2 + 2as

Since the car is decelerating, V = 0

And acceleration a will be negative.

U = 33 mph

S = 39 m

Substitute both into the formula

0 = 33^2 - 2 × a × 39

0 = 1089 - 78a

78a = 1089

a = 1089 / 78

a = 13.96 m/h^2

If we assume that the car decelerate at the same rate.

the distance the car will stop had it been going 66.0mph will be achieved by using the same formula

V^2 = U^2 + 2as

0 = 66^2 - 2 × 13.96 × S

4356 = 27.92S

S = 4356 / 27.92

S = 156.02 m

Therefore, the car would stop at

156.02 m

A typical ten-pound car wheel has a moment of inertia of about 0.35kg *m2. The wheel rotates about the axle at a constant angular speed making 70.0 full revolutions in a time interval of 4.00 seconds. What is the rotational kinetic energy K of the rotating wheel? Express answer in Joules

Answers

Answer:

The  rotational kinetic energy is  [tex]K = 2116.3 \ J[/tex]

Explanation:

From the question we are told that

    The moment of inertia  is  [tex]I = 0.35 \ kg \cdot m^2[/tex]

    The number of revolution is N  =  70 revolution

     The  time taken is  t  =  4.0  s

   

Generally the angular velocity is mathematically represented as

      [tex]w = \frac{2 \pi N }{t }[/tex]

substituting values

      [tex]w = \frac{2* 3.142 * 70 }{4 }[/tex]

       [tex]w = 109.97 \ rad/s[/tex]

     

The rotational kinetic energy K i mathematically represented as

       [tex]K = \frac{1}{ 2} * I * w^2[/tex]

substituting values

       [tex]K = \frac{1}{ 2} * 0.35 * (109.97)^2[/tex]

       [tex]K = 2116.3 \ J[/tex]

Given three resistors of different values, how many possible resistance values could be obtained by using one or more of the resistors?

Answers

Answer:

8 possible combinations

Assuming R 1, R 2 and R 3 be three different Resistance

1- all three in series

2-all three in parallel

3- R 1 and R 2 in series and parallel with R 3

4-R 1 and R 3 in series and parallel with R 2

5-R 2 and R 3 in series and parallel with R 1

6- R 1 and R 2

in parallel and series with R 3

7-R 1 and R 3 in parallel and series with R 2

8-R 2 and R 3 in V with R 1


A collector that has better efficiency in cold weather is the:
flat-plate collector due to reduced heat loss
evacuated tube collector due to its larger size
flat-plate collector due to the dark-colored coating
O evacuated tube collector due to reduced heat loss
Question 23 (1 point) Saved
One of the following is not found in Thermosyphon systems
o

Answers

Answer:

D. evacuated tube collector due to reduced heat loss

Explanation:

Evacuated tube collectors has vacuum which reduces the loss of heat and increase the efficiency of the collector. It has a major application in solar collector, and converts solar energy to heat energy. It can also be used for heating of a definite volume of water majorly for domestic purpose.

During cold weather, the conservation and efficient use of heat is required. Therefore, evacuated tube collector is preferred so as to reduce heat loss and ensure the maximum use of heat energy.


What characteristic makes Biology a science, but not Art History?
Using a process of testing ideas and gathering evidence
o Writing books about the subject
O Having a college degree to study it
Discussing and sharing ideas​

Answers

Using a process of testing ideas and gathering evidence.

Answer:

 

Using a process of testing ideas and gathering evidence

Explanation:

A diffraction grating 19.2 mm wide has 6010 rulings. Light of wavelength 337 nm is incident perpendicularly on the grating. What are the (a) largest, (b) second largest, and (c) third largest values of θ at which maxima appear on a distant viewing screen?

Answers

Answer:

(a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

Explanation:

Given that,

Width of diffraction grating [tex]w= 19.2\ mm[/tex]

Number of rulings[tex]N=6010[/tex]

Wavelength = 337 nm

We need to calculate the distance between adjacent rulings

Using formula of distance

[tex]d=\dfrac{w}{N}[/tex]

Put the value into the formula

[tex]d=\dfrac{19.2\times10^{-3}}{6010}[/tex]

[tex]d=3.19\times10^{-6}\ m[/tex]

We need to calculate the value of m

Using formula of constructive interference

[tex]d \sin\theta=m\lambda[/tex]

[tex]\sin\theta=\dfrac{m\lambda}{d}[/tex]

Here, m = 0,1,2,3,4......

[tex]\lambda[/tex]=wavelength

For largest value of  θ

[tex]\dfrac{m\lambda}{d}>1[/tex]

[tex]m>\dfrac{d}{\lambda}[/tex]

Put the value into the formula

[tex]m>\dfrac{3.19\times10^{-6}}{337\times10^{-9}}[/tex]

[tex]m>9.46[/tex]

[tex]m = 9[/tex]

(a). We need to calculate the largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{9\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=71.9^{\circ}[/tex]

(b). We need to calculate the second largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{8\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=57.7^{\circ}[/tex]

(c). We need to calculate the third largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{7\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=47.7^{\circ}[/tex]

Hence, (a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

A loop of wire is at the edge of a region of space containing a uniform magnetic field B. The plane of the loop is perpendicular to the magnetic field. Now the loop is pulled out of this region in such a way that the area A of the coil inside the magnetic field region is decreasing at the constant rate c. That is, dA/dt=−c, with c>0.Required:a. The induced emf in the loop is measuredto be V. What is the magnitude B of the magnetic field that the loop was in?b. For the case of a square loop of sidelength L being pulled out of the magneticfield with constant speed v, What is the rate of change of area c= -dA/dt

Answers

Answer:

The question is not clear enough. So i have attached a copy of the correct question.

A) B = V/c

B) c = Lv

Explanation:

A) we know that formula for magnetic flux is;

Φ = BA

Where B is magnetic field and A is area

Now,

Let's differentiate with B being a constant;

dΦ/dt = B•dA/dt

From faradays law, the EMF induced is given as;

E = -dΦ/dt

However, we want to express it in terms of V and E.M.F is also known as potential difference or Voltage.

Thus, V = -dΦ/dt

Thus, we can now say that;

-V = B•dA/dt

Now from the question, we are told that dA/dt = - c

Thus;

-V = B•-c

So, V = Bc

Thus, B = V/c

B) according to Faraday's Law or Lorentz Force Law, an electromotive force, emf, will be induced between the two ends of the sidelength:

Thus;

E =LvB or can be written as; V = LvB

Where;

V is EMF

L is length of bar

v is velocity

From the first solution, we saw that;

V = Bc

Thus, equating both of the equations, we have;

Bc = LvB

B will cancel out to give;

c = Lv

Explanation:


Somebody please help it’s urgent!!!!

In the tug of war game, none of the teams won. What can you conclude about the forces of the two teams ? Write all the evidence to support your answer.

Answers

Answer:

Explanation:

We can conclude that the forces of the two teams are equal and opposite and hence they cancel each other. Therefore none of the teams won as the rope did not move.

hope this helps

plz mark as brainliest!!!!!!!

A spring attached to the ceiling is stretched 2.45 meters by a four kilogram mass. If the mass is set in motion in a medium that imparts a damping force numerically equal to 16 times the velocity, the correct differential equation for the position x (t ), of the mass at a function of time, t is

Answers

Answer:

d²x/dt² = - 4dx/dt - 4x is the required differential equation.

Explanation:

Since the spring force F = kx where k is the spring constant and x its extension = 2.45 equals the weight of the 4 kg mass,

F = mg

kx = mg

k = mg/x

= 4 kg × 9.8 m/s²/2.45 m

= 39.2 kgm/s²/2.45 m

= 16 N/m

Now the drag force f = 16v where v is the velocity of the mass.

We now write an equation of motion for the forces on the mass. So,

F + f = ma (since both the drag force and spring force are in the same direction)where a = the acceleration of the mass

-kx - 16v = 4a

-16x - 16v = 4a

16x + 16v = -4a

4x + 4v = -a where v = dx/dt and a = d²x/dt²

4x + 4dx/dt = -d²x/dt²

d²x/dt² = - 4dx/dt - 4x which is the required differential equation

What is the separation in meters between two slits for which 594 nm orange light has its first maximum at an angle of 32.8°?

Answers

Answer:

1.1micro meter

Explanation:

Given that

Constructive interference is

ma = alpha x sin theta

Alpha = 1 x 594 x10^ -9/ sin 32.8°

= 1.1 x 10^ -6m

Explanation:

In a physics lab, light with a wavelength of 490 nm travels in air from a laser to a photocell in a time of 17.5 ns . When a slab of glass with a thickness of 0.800 m is placed in the light beam, with the beam incident along the normal to the parallel faces of the slab, it takes the light a time of 21.5 ns to travel from the laser to the photocell.What is the wavelength of the light in the glass? Use 3.00×108 m/s for the speed of light in a vacuum. Express your answer using two significant figures.

Answers

Answer:

196 nm

Explanation:

Given that

Value of wavelength, = 490 nm

Time spent in air, t(a) = 17.5 ns

Thickness of glass, th = 0.8 m

Time spent in glass, t(g) = 21.5 ns

Speed of light in a vacuum, c = 3*10^8 m/s

To start with, we find the difference between the two time spent

Time spent on glass - Time spent in air

21.5 - 17.5 = 4 ns

0.8/(c/n) - 0.8/c = 4 ns

Note, light travels with c/n speed in media that has index of refraction

(n - 1) * 0.8/c = 4 ns

n - 1 = (4 ns * c) / 0.8

n - 1 = (4*10^-9 * 3*10^8) / 0.8

n - 1 = 1.2/0.8

n - 1 = 1.5

n = 1.5 + 1

n = 2.5

As a result, the wavelength of light in a medium with index of refraction would then be

490 / 2.5 = 196 nm

Therefore, our answer is 196 nm

If a vacuum pump reduces the pressure of a gas to 1.0 x 10-6 atm, what is the pressure expressed in millimeters of mercury

Answers

Answer:

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

Explanation:

According to current SI unit conversions, 1 atmosphere is equal to 760 millimeters of mercury. The current pressure is determined by simple rule of three:

[tex]p = \frac{760\,mm\,Hg}{1\,atm} \times (1\times 10^{-6}\,atm)[/tex]

[tex]p = 7.6\times 10^{-4}\,mm\,Hg[/tex]

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?

Answers

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

       

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

Other Questions
How is genetic information preserved during the copying of DNA? View Available Hint(s) Hint 1.opened hint How is genetic information preserved during the copying of DNA? The information is preserved because DNA codes for RNA, which codes for protein. Genetic information is preserved in the linear sequence of the building blocks A, T, G, and C. Genetic information is preserved by base pairing between A and T and between G and C across the two strands of the double helix. The information in DNA is copied into RNA, which is used as a template to copy back to DNA. Read the excerpt from "Flight into Yesterday." This leg was also the most dangerous of the entire trip. Howland, 2,600 miles to the east, was a tiny speck of land in the middle of the vast Pacific. It would take all of her skill as a pilot and Freds as a navigator to find the island. But danger did not worry her. She knew that flying carried risks. She faced them and accepted them. What mattered was setting herself a challenge and meeting it. What mattered was showing that women could do what men could do and encouraging other women to do what they were capable of. That was why she was flying over the Pacific, looking for a speck of land. Fame was never her goal. The important thing was to do what she had set out to do and to do it as well as she knew how. She had been that way all her life. Amelia Earhart, world-famous flier, was very much like the young girl who once lived in Atchison, Kansas. What best describes the authors purpose? If 1 pound of grass seed costs 25x cents, represent in terms of x the cost of 7 pounds of seed? In polynomial simplest form The length of each side of a cubical wooden block is 16 inches. What is the volume ofthe block Which of the following is most likely the next step in the series?A.B.C.D. Which constants could each equation be multiplied by to eliminate the x-variable using addition in this system of equations? 2x+3y=25 -3x+=22 first equation can be multiplied by 3 and the second equation by 2. The first equation can be multiplied by 4 and the second equation by 2. The first equation can be multiplied by 3 and the second equation by 2. The first equation can be multiplied by 4 and the second equation by 3. Carlos is using the software development life cycle to create a new app. He has finished coding and is ready to see the output it produces. Which stage of the software development life cycle is Carlos ready for next? Coding Design Maintenance Testing The equator and the prime mediran break up the earth into which hemispheres?? Following are several figures reported for Allister and Barone as of December 31, 2018:Allister BaroneInventory $530,000 $330,000Sales 1,060,000 860,000Investment income not given Cost of goods sold 530,000 430,000Operating expenses 245,000 315,000Allister acquired 70 percent of Barone in January 2017. In allocating the newly acquired subsidiary's fair value at the acquisition date, Allister noted that Barone had developed a customer list worth $70,000 that was unrecorded on its accounting records and had a 4-year remaining life. Any remaining excess fair value over Barone's book value was attributed to goodwill. During 2018, Barone sells inventory costing $126,000 to Allister for $172,000. Of this amount, 20 percent remains unsold in Allister's warehouse at year-end. Determine balances for the following items that would appear on Allister's consolidated financial statements for 2018:AmountsInventory Sales Cost of goods sold Operating expenses Net income attributable to noncontrolling interest Solve the equation using the square root method. Select all solutions that apply. x^2 = 36 A.-8 B.6 C.-6 D.8 What word means continual trouble or distress Light travels at a speed of 2.998*108 m/s. Light takes approximately 3.25 minutes to travel from the Sun to reach a planet. Calculate the distance from the Sun to this planet in meters. Give your answer to 0 decimal places. A sample of bacteria is decaying according to a half-life model. If the sample begins with 700 bacteria, and after 10 minutes there are 140 bacteria, after how many minutes will there be 40 bacteria remaining? Round your answer to the nearest whole number. in this diagram, bac~edf. if the area of bac= 6 in., what is the area of edf? PLZ HELP PLZ PLZ PLZ Which two complex numbers when subtracted from each other equal another complex number from the table? A -3 4i B -7 6i C 13 + i D -9 + 6i E 8 8i F -15 + 9i G 2 + 12i H 6 10i Ignacio ________ enojado conmigo. The graph of y = 4x2 + 13x + 12 is shown below. What are the zeros of the function (as exact values), the y-intercept, and the maximum or minimum value of the function? Luther Corporation Consolidated Balance Sheet December 31, 2006 and 2005 (in $ millions) .2006 2005Assets Liabilities and Stockholders' Equity 2006 2005 Current Assets Current Liabilities Cash 56.1 58.5 Accounts payable 88.1 73.5 Accounts receivable 54.5 39.6 Notes payable / short-term debt 10.9 9.6 Inventories 44.8 42.9 Current maturities of long-term debt 40.7 36.9 Other current assets 5.0 3.0 Other current liabilities 6.0 12.0 Total current assets 160.4 144.0 Total current liabilities 145.7 132.0 Long-Term Assets Long-Term Liabilities Land 66.8 62.1 Long-term debt 227 168.9 Buildings 108.5 91.5 Capital lease obligations Equipment 117.1 99.6 Less accumulated depreciation (54.4) (52.5) Deferred taxes 22.8 22.2 Net property, plant, and equipment 238 200.7 Other long-term liabilities --- --- Goodwill 60.0 -- Total long-term liabilities 249.8 191.1 Other long-term assets 63.0 42.0 Total liabilities 395.5 323.1 Total long-term assets 361 242.7 Stockholders' Equity 125.9 63.6 Total Assets 521.4 386.7 Total liabilities and Stockholders' Equity 521.4 386.7 Refer to the balance sheet above. If in 2006 Luther has 10.2 million shares outstanding and these shares are trading at $16 per share, then what is Luther's enterprise value?A. -$540.0 million.B. $771.4 million.C. $385.7 million.D. $521.4 million. Find the odds in favor and the odds against a randomly selected person from Country X, age 25 and over, with the stated amount of education. four years (or more) of college Which property can you apply to Hayley's expression to show that it is equivalent to Gretchens expression?