Question
A rabbit moves a distance of 85 meters in 13 seconds.

What is the rabbits average speed?
7.26 m/s
0.15 m/s²
6.54 m/s
6.54 m/s²

Between 400 nm and 700 nm of the electromagnetic spectrum, vegetation has the strongest response.

The electromagnetic spectrum travels in waves and spans an extensive spectrum from very long radio waves to very brief gamma rays. The human eye can simplest come across only a small portion of this spectrum called visible light.

In order from maximum to lowest power, the sections of the EM spectrum are named: gamma rays, X-rays, ultraviolet radiation, visible mild, infrared radiation, and radio waves.

In a tumbler, the purple mild travels the fastest, and the violet light travels the slowest of all seven hues. Velocity and wavelength are without delay proportional.

Learn more about Electromagnetic spectrum here:-https://brainly.com/question/23423065

#SPJ4

Air resistance is hardly noticeable. true regarding the 0.09-kilogram component. This causes 0.01kg to land farther from the launch site than 0.09kg did.

0.09kg will move to the west due to momentum conservation (opposite of 0.01 kg). Additionally, since both are at the same height above the ground, it will take them equal amounts of time to descend to the ground.

Allowing v to be the speed of 0.01 kg, which means that the speed of 0.09kg will be smaller than 0.01 kg,

0.01v - (0.09)V = 0

V = 0.01 v/ 0.09 = 0.111v

The speed of 0.09 kg = 0.111v

The speed of 0.09 kg is less than 0.01kg.

Because of this, 0.01kg hits the ground farther from the launch point than 0.09kg did.

The amount of resistance in an electrical circuit represents the resistance to current flow. The Greek letter omega (), which represents resistance, represents ohms. German physicist Georg Simon Ohm (1784–1854), who investigated the connection between voltage, current, and resistance, is the name given to the unit of resistance known as an ohm.

Resistance measurements are typically performed in order to evaluate the health of a component or a circuit.

Current flow is inversely correlated with resistance. Conductor damage from corrosion or burning could be one of several potential causes if it is extremely high.

Learn more about resistance here:

https://brainly.com/question/17010736

#SPJ4

The amplitude is 0.25s.

Calculation:

Amplitude = A = 0.225 m

Angular frequency = w = 8π rad/s.

Frequency = f = w/2π = 8π/2πHZ = 4 HZ

Time period = T = 1/f = (1/4)s = 0.25s.

The maximum displacement or distance traveled by a point on an oscillating body or shaft, measured from the equilibrium position. This corresponds to half the length of the vibration path. Amplitude difference between a rest position and maximum shaft deflection.

Frequency The number of waves passing a particular point per second. Duration  How long it takes for a wave cycle to complete. Sound wave amplitude is a measure of wave height. The amplitude of a sound wave can be defined as the magnitude or loudness of the maximum displacement from the average position of the vibrating particles in the medium when the sound was produced.

Learn more about The amplitude here:- https://brainly.com/question/3613222

#SPJ4

The final velocity of the cannonball-cart system is less than the initial velocity of the cannonball and the system will move in the direction of the cannonball ( V < v_b ).

The law of conservation of linear momentum states that the sum of the initial momentum is equal to sum of the final momentum, provided that the system is Isolated.

Mathematically, the law of conservation of linear momentum is given as;

Pi = Pf

where;

m₁u₁ + m₂u₂ = v ( m₁ + m₂ )

where;

since the cart is initially at rest, the initial velocity of the cart = 0

m₁u₁ + 0 = v ( m₁ + m₂ )

m₁u₁ = v ( m₁ + m₂ )

v = ( m₁u₁ ) / ( m₁ + m₂ )

given initial velocity of the cannon ball = v_b

The final velocity of the cannonball-cart system is calculated as follows;

V = ( m₁v_b ) / ( m₁ + m₂ )

Hence, V < v_b

Learn more about linear momentum here: https://brainly.com/question/7538238

#SPJ1

The distance before it falls back to the earth is 8.5 * 103 km. Option B

We know that the escape velocity has to do with the velocity that has to be supplied to a material so that the material can be able to escape from the earth's gravitational pull. Let us recall that the whole earth is a large gravitational field. If we throw an object up then the object would have to certainly fall doen to the ground under the influence of gravity.

It is therefore clear that gravity is the force that draws any object that  goes upwards down back to the ground. Given that we have been told here that the speed is  one-half of the escape speed, then then the magnitude of the speed is 5590.3 m/s.

Given that;

v^2 = u^2 - 2gh

v = final velocity

u = initial velocity

g = acceleration due to gravity

h = height

Then;

u^2 = 2gh

h = u^2/2g

h = ( 5590.3)^2/2 * 9.8

=  8.5 * 103 km

Learn more about escape velocity:https://brainly.com/question/14297933

#SPJ1

Answer:

Here, h1=4.00m,h92)=3.00m,Delta t =0.01 s.Letv1 be the velocity of the ball (actind downwards) just before striking the floor an dv20 be the velocity of the ball (acting upwaeds) ust after striking the floor. Then, change in velocity of the ball in time Δtv2−(−v1)v2+v1

:. acceleration, a=v2+v1Δt ..(i)

When body falls from height h1,

then u=o,v1,a=gandS=h1

As, v21=u2+2aS,

:. v_(1) ^(2) =0 + g h_(10 or v12–√gh1

Taking motion of the ball after striking the floor, then u=v2,v=0,a=−g,S=h2

As, v2=u22as,∴v21=0+2gh1orv_(1) =sqrt 32 g h_(1)Tak∈gmotionoftheballa>erstrik∈gthe⌊,⌋thenu=v_(2), v=0, a=- g, S=h_(2)As,v2=u2+2aS,wehave0 = v_(2)^(2) +2 (-g) h_92) otr v2=2–√gh2

Putting values in (i) we get,

a=2–√gh2+2–√gh1Δt)

a=2–√×9.8×3+2–√×9.8×40.01

= 1652m/s2.

Explanation:

If an object producing sound is moving away from us, the wavelength of the sound heard is longer than the actual wavelength. The conclusion is from the concept of Doppler effect.

The Doppler's effect is a phenomenon when the source of a wave and an observer move relative to each other, the frequency heard is not the same with the actual frequency.

The equation of the Doppler effect is

f₀ = [(v ± v₀)/(v ± vs)] × fs

Where

Note:

When an object producing sound is moving away from us, the frequency of the sound we heard changed.

Let's say we are at rest, it means v₀ = 0. The sound source is moving away makes vs (+).

With the Doppler's effect, we get

f₀ = [(v+0) / (v+vs)] × fs

f₀/fs = v/(v+vs)

v < v+vs

f₀ < fs

The frequency of sound we heard is lower that the actual frequency.

The wavelength is inversely proportional to the frequency. It is described in the equation:

λ = c/f

It means that the lower the frequency, the longer the wavelength.

Hence, the phenomenon which the wavelength of the sound we heard is longer than the actual wavelength when the sound source is moving away from us is called the Doppler's effect.

Here is the group of answer choices:

(a) Band width

(b) Doppler's effect

(c) Sound refraction

(d) Vibrations

Learn more about Doppler's effect here:

https://brainly.com/question/29672712

#SPJ4

The force of gravity acting on the 23 Kg object in the diagram is 225.4 N

The force of gravity is defined as follow:

Force of gravity (F) = mass (m) × acceleration due to gravity (g)

Using the above formula, we can easily obtain the force gravity acting on the 23 Kg object. This is shown below:

Force of gravity (F) = mass (m) × acceleration due to gravity (g)

Force of gravity = 23 Kg × 9.8 m/s²

Force of gravity = 225.4 N

Thus, from the calculation made above, we can conclude that the gravitaional force is 225.4 N

Learn more about force:

https://brainly.com/question/12163222

#SPJ1

Particles can exist in classically forbidden regions outside the finite square-well potential.

The correct option is D.

In the absence of quantum effects, everything would be continuous, smooth, and completely predictable in the Newtonian sense. However, we may not be here to get bored with this if Planck's constant were 0.

At the atomic scale, the behavior of both particles and waves is described by Planck's constant. One of the factors that led to the creation of quantum mechanics is Planck's constant. It was a surprise when those boundaries also turned to represent the limits where known rules of physics applied since the Planck scaled was developed as an universal set of units.

To know more about Planck constant visit:

https://brainly.com/question/2289138

#SPJ4

The smooth plastic jar has five pennies placed inside of it. The normal reactions of the bottom coin on the container at locations a and b will be 0.0705 lb and 0.1175 lb respectively if each coin weighs 0.0235 lb.

A contact force, the normal force is often referred to as the normal reaction force. On two surfaces that are not attached to one another, a normal force cannot be applied.

The body's weight determines the usual deceleration force. A body's position relative to the ground tells us when it is about to fall. The normal force is the portion of a force that is perpendicular to any contact surface.

To learn more about normal force visit:

brainly.com/question/13340671

#SPJ4

(a) θ5 in the air is 56.9° and (b) θ4 in the bottom material 35.30°. Normally, a light beam that strikes an angle on a prism's refracting face emerges from the opposite face.

(a) Approximating n=1 for air, we have

n1. sinθ1 = (1)sinθ5 ⇒56.9°=θ5

​and with the more accurate value for n air in Table below, we obtain 56.80.(b) Equation n1 sinθ c =n2 sin 90° leads to,

n1 sinθ 1=n2 ​sinθ2​ =n3​ sinθ 3​ =n4 sinθ 4

​so that. θ4 =sin −1( n1/n4.sinθ 1 )=35.30° .

The angle of incidence is formed by a line drawn perpendicular to the reflecting barrier and the wave's direction of motion.

Refraction Depending on the Refractive Indices in the Two Media and the Angle of Incidence. Snell's law states that the angle of incidence, I and the proportion of the refractive indices of the two media that make up the interface determine the angle of refraction, r.

Learn more about refraction here:

https://brainly.com/question/14760207

#SPJ4

The reactive power of the branch (Qb) can be calculated from its voltage and current 676.16 VA.

Reactive power is the power in an AC circuit that is required to establish and maintain a voltage across a load. It is associated with the storage and release of energy in the form of electric and magnetic fields. Reactive power does not contribute to the actual work output of a system and is measured in Volt-amperes reactive (VARs). Power factor is a measure of reactive power relative to the total power in a system.

Source frequency = 60 Hz
Generator impedance = 0 W
Circuit:
Vg = 170 V
R1 = 10 Ω
R2 = 20 Ω
Zb = 20 + j10 Ω

The current flowing through the generator (Ig) and the branch (Ib) can be calculated from Ohm's Law:
Ig = Vg/R1 + Vg/R2 = 170/10 + 170/20 = 17 A
Ib = Ig - Vg/Zb = 17 - 170/(20 + j10) = 17 - 16.4 + j4.4 = 0.6 + j4.4 A
Since Ib is a complex number, we can find its magnitude (|Ib|) and angle (θ):
|Ib| = √(0.6² + 4.4²) = 4.46 A
θ = tan⁻¹(4.4/0.6) = 80.16°
The voltage across the branch (Vb-n) can be calculated using Ohm's Law:
Vb-n = Ib × Zb = (0.6 + j4.4) × (20 + j10) = -8.4 + j74.4 V
The apparent power of the branch (Sb) can be calculated from its voltage and current:
Sb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = -45.48 + j367.04 VA
The real power of the branch (Pb) can be calculated from its voltage and current:
Pb = Vb-n × Ib = (-8.4 + j74.4) × (0.6 + j4.4) = -45.48 - j367.04 W
The reactive power of the branch (Qb) can be calculated from its voltage and current:
Qb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = 676.16 VA

To learn more about reactive power
https://brainly.com/question/23230296
#SPJ4

A inaccessible object is a dynamic variable on the free store without any pointer pointing to it.

Utilize the sextant's arc to determine the angle. By dividing the object's distance from the point of observation by the tan of the angle you calculated, you may use a scientific calculator to get the object's height.

The measuring of heights and distances that are unreachable is made easier by right-triangle trigonometry. By drawing a right triangle with the unknown height or distance as one of its sides and a known side and angle on the other, it is possible to determine the unknown height or distance.

To know more about inaccessible object visit:

https://brainly.com/question/21989844

#SPJ4

Answer:

dynamic variable

The general instinct hypothesis, which contends that people are physiologically predisposed to or possess inclinations for violent behaviours, is known as the instinct theory of aggression in psychology.

In an effort to understand why we become aggressive and whether that behaviours can be altered, psychologists have developed three primary theories of aggression. Although many hypotheses have been put out, these three have proven most reliable and are crucial to comprehending the origins of violence. These hypotheses comprise as,

To know more about theory of aggression

https://brainly.com/question/3197702

#SPJ4

Transmission coefficients are used in physics and electrical engineering when considering wave propagation in discontinuous media. The snells law is n₁sinθ1 = n₂sinθ2

The transmission coefficient describes the amplitude intensity or total power of the transmitted wave relative to the incident wave. The transmission coefficient is defined as the ratio of the transmitted particle flux to the incident particle flux and depends on the incident energy.

The sum of the reflected and transmitted energy must equal the total incident energy, so the transmission coefficient is calculated simply by subtracting the reflection coefficient. The ratio of the reflected wave amplitude to the incident wave amplitude is called the reflection coefficient.

Learn more about The transmission coefficients here:- https://brainly.com/question/9323897

#SPJ4

Due to an automobile accident, Jenny suffered damage to her cerebral cortex in Broca's area. Jenny is most likely to experience: aphasia.

Aphasia is the inability to understand or form language due to damage to certain areas of the brain The main causes are stroke and head trauma. Although the prevalence is difficult to determine, aphasia due to stroke is estimated at 0.1-0.4% in the Global North. Aphasia can also be the result of a brain tumor, brain infection, or neurodegenerative disease (such as dementia).

To be diagnosed with aphasia, communication after an acquired brain injury Speech or language must be significantly impaired in one (or more) of the four aspects of Alternatively, in the case of progressive aphasia, it must have decreased significantly over a short period of time. The four dimensions of communication are auditory comprehension, verbal expression, reading and writing, and functional communication.

Learn more about Aphasia here : https://brainly.com/question/4045064

#SPJ4

The voltage drops in terms of vb , i2 , i3 , the given resistances, and any other given quantities.ΣΔV = 0 = I3 ⋅ R3 - I2 ⋅ R2.

When applying Kirchhoff's second rule the loop rule we need to identify closed loops and decide whether to loop clockwise or counterclockwise. For example, in Figure 3 the loop was traversed in the same direction as the current.

Loop 1 is the full loop and Loop 2 is the small loop on the right. To apply the loop rule, add all those voltage changes. Kirchhoff's Second Law, also known as Kirchhoff's Voltage Law states that the sum of all voltages around the closed loop of any circuit must be zero. This is a result of charge conservation and energy conservation.

Learn more about The loop rule here:- https://brainly.com/question/15705903

#SPJ4

The length of the y component shown is C. 2.0.

We are given the angle of the vector, and the length of one of the components of the vetor. Given the angle we have, the available component is the hypotenuse. The y component that we are to find, will then be the opposite or perpendicular component.

To solve for the length of the y - component therefore, the useful operation would be the Sin function.

The length of the y - component would be:
Sin 42 ° = Opposite / Hypotenuse

Sin 42 ° = y component / Hypotenuse

y - component = Sin 42 ° x Hypotenuse

y - component = Sin 42 ° x 3

y - component = 0. 6691 x 3

y - component = 2. 0

In conclusion, the y - component is 2.0.

Find out more on  y-component at https://brainly.com/question/3387587

#SPJ1

Full question is:

What is the length of the y-component of the vector shown below?

Parallax, main-sequence fitting, cepheid variables, Tully-Fisher relation, and Hubble's law are the sequence lists methods for determining distance.

Parallax is the closest method for determining distance. This method uses the principle of triangulation to measure the distance of a nearby star relative to Earth. Main-sequence fitting is another method used to measure the distance of stars. This method compares the brightness of a star to other stars of known distance and luminosity to determine its distance.

Cepheid variables are stars whose brightness varies in a predictable way over time. This method uses the period of the star's brightness to determine its intrinsic luminosity, and then its distance. The Tully-Fisher relation is a method for measuring the distance of galaxies. This method uses the rotation speed of the galaxy and its brightness to calculate its distance.

Finally, Hubble's law is the most distant method for determining distance. This law states that the farther away a galaxy is, the faster it moves away from us. This allows us to calculate the distance of galaxies by measuring their rate of recession.

For more questions like Hubble's law click the link below:

https://brainly.com/question/29869676

#SPJ4

The value of 'x' such that the mass то exerts a force of mg on the inclined surface at P. (N=mg)​ is given by

x = N / (mg cos θ)

Generally, To determine the value of 'x', you need to know the angle of inclination of the surface and the mass of the object. The force of gravity (N) acting on the object is equal to the mass of the object (m) multiplied by the acceleration due to gravity (g). The force of gravity is also equal to the normal force (N) exerted by the surface on the object, which is perpendicular to the surface.

If the surface is inclined at an angle θ with respect to the horizontal, the normal force will be equal to the component of the force of gravity along the surface. This component can be calculated using the formula N = mg cos θ, where θ is the angle of inclination and m is the mass of the object.

Therefore, to determine the value of 'x', you need to solve the equation N = mg cos θ for 'x'. To do this, you can rearrange the equation to solve for x:

x = N / (mg cos θ)

Substituting the values of N, m, and θ into this equation will give you the value of 'x' that you are looking for.

Read more about mass of the object.

https://brainly.com/question/6240825

#SPJ1

To get the work, you have to integrate the force as a function of [tex]$x$[/tex] from zero displacement to Xo

[tex](Integral of) $\mathrm{k} \mathrm{x}^{\wedge} 2 \mathrm{dx}$ from 0 to $\mathrm{Xo}_{\mathrm{o}}=(1 / 3) \mathrm{k}\left(\mathrm{Xo}^{\wedge}\right)^{\wedge} 3$[/tex]

The work done by stretching the spring to the given distance is [tex]W=\frac{k x_0}{3}[/tex]

The given parameters:

- Applied force on the spring [tex]$=F$[/tex]

- Extension of the spring [tex]$=x_0$[/tex]

The work done by stretching the spring to the given distance is calculated as follows;

[tex]W=\frac{k x_0}{3}[/tex]

[tex]$$\begin{aligned}& W=\int_{x_a}^{x_b} F d x \\& W=\int_{x_a}^{x_b} k x^2 d x \\& W=k \int_{x_a}^{x_b} x^2 d x \\& W=k\left[\frac{x^3}{3}\right] \\& W=k\left[\frac{x_b-x_a}{3}\right] \\& W=k\left[\frac{x_0-0}{3}\right] \\& W=\frac{k x_0}{3}\end{aligned}[/tex]

Thus, the work done by stretching the spring to the given distance is

[tex]W=\frac{k x_0}{3}[/tex]

measure of energy transfer that occurs when an object is moved over a distance by an external force at least part of which is applied in the direction of the displacement.

To learn more about work done visit:

https://brainly.com/question/13662169

#SPJ4