Modern wind turbines are larger than they appear, and despite their apparently lazy motion, the speed of the blades tips can be quite high-many times higher than the wind speed. A turbine has blades 53m long that spin at 14 rpm.

Required:
a. At the tip of a blade, what is the speed?
b. At the tip of a blade, what is the centripetal acceleration?

Answers

Answer 1

Explanation:

Given that,

The length of the blades, l = 53 m

The angular velocity = 14 rpm = 1.466 rad/s

(a) The speed at the tip of a blade.

[tex]v=r\omega\\\\=53\times 1.466\\\\=77.69\ m/s[/tex]

(b) The centripetal acceleration at the tip of the blade is :

[tex]a=\dfrac{v^2}{r}\\\\a=\dfrac{77.69^2}{53}\\\\a=113.88\ m/s^2[/tex]

Hence, this is the required solution.


Related Questions

what do we mean by thrust?

Answers

Answer:

the answer is push example: she thrust her hand into her pocket

00
Use base units to check whether the following equations are balance
(a) pressure = depth x density gravitational field strength,
(b) energy = mass x (speed of light).
dod to molt solid

Answers

Answer:

In a column of fluid, pressure increases with depth as a result of the weight of the overlying fluid. Thus a column of fluid, or an object submerged in the fluid, experiences greater pressure at the bottom of the column than at the top. This difference in pressure results in a net force that tends to accelerate an object upwards.

The pressure at a depth in a fluid of constant density is equal to the pressure of the atmosphere plus the pressure due to the weight of the fluid, or p = p 0 + ρ h g , p = p 0 + ρ h g , 14.4

Granite: 2.70 × 10 32.70 × 10 3

Lead: 1.13 × 10 41.13 × 10 4

Iron: 7.86 × 10 37.86 × 10 3

Oak: 7.10 × 10 27.10 × 10 2

Differences between LED and CFL bulb..​

Answers

Explanation:

CFL bulbs were made to take the place of incandescent bulbs, which generate light as a result of heat. ... LED (light-emitting diode) is a type of bulb that produces light using a narrow band of wavelengths. LED lighting is more energy efficient than CFL bulb.

Liquid plastic is frozen in a physical change that increases its volume. What can be known about the plastic after the change?
(A) Its mass will increase.
(B) Its density will increase.
(C) Its mass will remain the same.
(D) Its density will remain the same.

Answers

Answer:

c

Explanation:

Liquid plastic is frozen in a physical change that increases its volume,it can be known about the plastic that Its mass will remain the same, therefore the correct answer is option C.

What is the matter?

Anything which has mass and occupies space is known as matter ,mainly there are four states of matter solid liquid gases, and plasma.

These different states of matter have different characteristics according to which they vary their volume and shape.

It is known about plastic that its mass will remain the same when liquid plastic is frozen, by increasing its volume.

Liquid plastic is frozen in a physical change that increases its volume,it can be known about the plastic that Its mass will remain the same,  therefore the correct answer is C.

To earn more about the matter here,refer to the link;

brainly.com/question/9402776

#SPJ2

Consider two closely spaced and oppositely charged parallel metal plates. The plates are square with sides of length L and carry charges Q and -Q on their facing surfaces. What is the magnitude of the electric field in the region between the plates

Answers

Answer:

  E_ {total} = [tex]\frac{Q }{L^2 \epsilon_o}[/tex]

Explanation:

In this exercise you are asked to calculate the electric field between two plates, the electric field is a vector

         E_ {total} = E₁ + E₂

         E_ {total} = 2 E

where E₁ and E₂ are the fields of each plate, we have used that for the positively charged plate the field is outgoing and for the negatively charged plate the field is incoming, therefore in the space between the plates for a test charge the two fields point in the same direction

to calculate the field created by a plate let's use Gauss's law

          Ф = ∫ E . dA = q_{int} /ε₀

As a Gaussian surface we use a cylinder with the base parallel to the plate, therefore the direction of the electric field and the normal to the surface are parallel, therefore the scalar product is reduced to the algebraic product.

           E 2A = q_{int} / ε₀

where the 2 is due to the surface has two faces

indicate that the surface has a uniform charge for which we can define a surface density

           σ = q_{int} / A

           q_{int} = σ A

we substitute

           E 2A = σ A /ε₀

           E = σ / 2ε₀  

therefore the total field is

           E_ {total} = σ /ε₀

let's substitute the density for the charge of the whole plate

           σ= Q / L²

           

            E_ {total} = [tex]\frac{Q }{L^2 \epsilon_o}[/tex]

Who should you invite to the meeting?

—-

Answers

Answer

Irma

Explanation:

You should invite Irma to the meeting because she is in Charlotte and she also visited after 10/24/20

The mass flow rate through a centrifugal compressor is 1 kg/s. If air enters at 1 bar and 288k and leaves at 200 kN/m² and 370k, determine the power of the compressor. Take Cp = 1.103 kJ (kg.K), R = 287 kJ (kg.k)​

Answers

We have that the power of the compressor is

[tex]H_p=24.242hp[/tex]

From the question we are told that:

Flow rate [tex]W=1kg/s[/tex]

inlet Pressure [tex]P_1=1 bar[/tex]

inlet Temperature [tex]T_1= 288k[/tex]

Outlet Temperature [tex]T_2= 370k[/tex]

Outlet Pressure [tex]P_2=200 kN/m^2=2bars[/tex]

[tex]Cp = 1.103 kJ[/tex]

[tex]R = 287 kJ (kg.k)​[/tex]

Generally, the equation for Adiabatic head  is mathematically given by

[tex]H=\frac{ZRT_1}{Cp-1/K}[\frac{P_2}{P_1}^{(Cp-1)/Cp}-1][/tex]

Where

[tex]Z=Compressibility\ factor[/tex]

[tex]Z=0.99[/tex]

Therefore

[tex]H=\frac{(0.99)(287)(288)}{(1.103)-1/(1.103)}[\frac{(200)}{(1)}^{((1.103)-1)/(1.103)}-1][/tex]

[tex]H=560925.5958 J/kg[/tex]

[tex]H=5.6*10^5J/kg[/tex]

Generally, the equation for centrifugal compressor power  is mathematically given by

[tex]H_p=\frac{WH}{E*33000}[/tex]

Where

E is efficiency (adiabatic)

[tex]E=70\%=0.7[/tex]

Therefore

[tex]H_p=\frac{(1)(5.6*10^5)}{0.7*33000}[/tex]

[tex]H_p=24.242hp[/tex]

In conclusion

The power of the compressor is

[tex]H_p=24.242hp[/tex]

For more information on this visit

https://brainly.com/question/13389697

A 10 n force is applied horizontally on a box to move it 10 m across a frictionless surface. How much work was done to move the box?

Answers

Given from question
Force = 10 N
Displacement = 10 m
Work done = ?
We know that
Work done = force X displacement
So 10 X 10
100
Work done = 100J answer

Answer:

[tex]\boxed {\boxed {\sf 100 \ J}}[/tex]

Explanation:

We are asked to calculate the work done to move a box.

Work is the product of force and distance or displacement.

[tex]W= F*d[/tex]

A 10 Newton force is applied horizontally on the box. Since the surface is frictionless, there is no force of friction, and the net force is 10 Newtons. The force moves the box 10 meters.

F= 10  N d= 10 m

Substitute the values into the formula.

[tex]W= 10 \ N * 10 \ m[/tex]

Multiply.

[tex]W= 100 \ N*m[/tex]

Let's convert the units. 1 Newton meter is equal to 1 Joule, therefore our answer of 100 Newton meters is equal to 100 Joules.

[tex]W= 100 \ J[/tex]

100 Joules of work was done to move the box.


In the diagram, the amplitude of the wave is shown by:

A
B
C
D

Answers

Answer:

A.

Explanation:

Amplitude measures how much a wave rises or falls. This is illustrated by A.

In the diagram, the amplitude of the wave is shown by A.

What is Amplitude?The amplitude of a periodic variable is a measure of its change in a single period. The amplitude of a non-periodic signal is its magnitude compared with a reference value.

There are various definitions of amplitude, which are all functions of the magnitude of the differences between the variable's extreme values.

The amplitude of a variable is simply a measure of change relative to its central position. In contrast, magnitude is a measure of the distance or quantity of a variable irrespective of its direction.

Amplitude is a property that is unique to waves and oscillations.

Therefore, in the diagram, the amplitude of a wave is shown by A.

To learn more about amplitude, refer:

https://brainly.com/question/3613222

#SPJ2

A 50-turn coil has a diameter of . The coil is placed in a spatially uniform magnetic field of magnitude so that the face of the coil and the magnetic field are perpendicular. Find the magnitude of the emf, , induced in the coil if the magnetic field is reduced to zero unfiformly

Answers

Answer:

EMF = 51.01 Volt

Explanation:

A 50-turn coil has a diameter of 15 cm. The coil is placed in a spatially uniform magnetic field of magnitude 0.500~\text{T}0.500 T so that the plane of the coil makes an angle of 30^\circ30 ​∘ ​​ with the magnetic field. Find the magnitude of the emf induced in the coil if the magnetic field is reduced to zero uniformly in 0.100~\text{s}0.100 s

We have,

Number of turn in the coil, N = 50

The diameter of the coil, d = 15 cm

Radius, r = 7.5 cm = 0.075 m

Initial magnetic field, [tex]B_i=0.5\ T[/tex]

The plane of the coil makes an angle of 30° with the magnetic field.

The magnetic field reduced to zero in 0.1 seconds

We need to find the emf induced in the coil. We know that, emf is equal to the rate of change of magnetic flux. So,

[tex]\epsilon=\dfrac{BNA\cos\theta}{t}\\\\\epsilon=\dfrac{0.5\times 50\times \pi \times 0.075\cos(30)}{0.1}\\\\\epsilon=51.01\ V[/tex]

So, the induced emf in the coil is 51.01 V.

Definition of distance in physics

Answers

Answer:

Distance is a scalar quantity that refers to "how much ground an object has covered" during its motion. Displacement is a vector quantity that refers to "how far out of place an object is"; it is the object's overall change in position.

Explanation:

A chair of weight 85.0 N lies atop a horizontal floor; the floor is not frictionless. You push on the chair with a force of F = 40.0 N directed at an angle of 35.0deg below the horizontal and the chair slides along the floor.
Using Newton's laws, calculate n, the magnitude of the normal force that the floor exerts on the chair.

Answers

Answer:

 N = 107.94 N

Explanation:

For this exercise we must use Newton's second law.

Let's set a reference system with the x-axis parallel to the ground and the y-axis vertical

X axis

        Fₓ = ma

ej and

       N -F_y - W = 0

let's use trigonometry to decompose the applied force

     cos -35 = Fₓ / F

     sin -35 = F_y / F

     Fₓ = F cos -35

     F_y = F sin -35

     Fₓ = 40.0 cos -35 = 32.766 N

     F_y = 40.0 sin -35 = -22.94 N

we substitute

     N = Fy + W

     N = 22.94 + 85

     N = 107.94 N

you use 20cm of wrench

Answers

Answer:

okk

now what do I do with it

A single force acts on a particle situated on the positive x axis. The torque about the origin is in the negative z direction. The force might be:_______.
A. in the positive y direction
B. in the negative y direction
C. in the positive x direction
D. in the negative x direction

Answers

C maybe don’t count on it 100%

A single force acts on a particle situated on the positive x axis. The torque about the origin is in the negative z direction. The force might be in the negative y direction. Thus, option B is correct.

To determine the force that could generate a torque in the negative z direction, we need to consider the right-hand rule for cross products. The torque vector, denoted by τ, is given by the cross product of the position vector, r, and the force vector, F:

[tex]τ = r × F[/tex]

In this case, the position vector, r, points along the positive x-axis. The negative z-direction torque indicates that the force vector must be perpendicular to both the position vector and the negative z-axis.

Using the right-hand rule, we can determine that the force vector must be in the negative y-direction, which is option B.

Learn more about vector on:

brainly.com/question/16038935

#SPJ2

A 771.0-kg copper bar is melted in a smelter. The initial temperature of the copper is 300.0 K. How much heat must the smelter produce to completely melt the copper bar? For solid copper, the specific heat is 386 J/kg • K, the heat of fusion is 205 kJ/kg, and the melting point is 1357 K.

Answers

Answer:

4.73 × 10^5

Explanation:

what is the value of x if x-36=5?​

Answers

Answer:

Therefore, the value of x is 41

Explanation:

x=5+36

x=41

Need help with this one! Thank you xoxo!

Answers

Answer:

it's electron attraction

The answer is Electron Attraction

Hey guys,I hope u r gonna answer this question fast,SI system is extended from of MKS system.Why? I will be waiting for the answer. Good luck thank u​

Answers

Answer:

Because SI system has fundamental units of MKS System

Answer:

Explanation: the unit of length ,mass , and time are same in both the system , thus, the SI system is the extended from of MKS system.

During the data transmission there are chances that the data bits in the frame might get corrupted. This will require the sender to re-transmit the frame and hence it will increase the re-transmission overhead. By considering the scenarios given below, you have to choose whether the packets should be encapsulated in a single frame or multiple frames in order to minimize the re-transmission overhead.


Justify your answer with one valid reason for both the scenarios given below.


Scenario A: Suppose you are using a network which is very prone to errors.


Scenario B: Suppose you are using a network with high reliability and accuracy.

Answers

1. Based on Scenario A, multiple frames will minimize re-transmission overhead and should be preferred in the encapsulation of packets.

2. Based on Scenario B, the encapsulation of packets should be in a single frame because of the high level of network reliability and accuracy.

 

Justification:

There will not be further need to re-transmit the packets in a highly reliable and accurate network environment, unlike in an environment that is very prone to errors.  The reliable and accurate network environment makes a single frame economically better.

Encapsulation involves the process of wrapping code and data together within a class so that data is protected and access to code is restricted.

With encapsulation, each layer:

provides a service to the layer above itcommunicates with a corresponding receiving node

Thus, in a reliable and accurate network environment, single frames should be used to enhance transmission and minimize re-transmission overhead.  This is unlike in an environment that is very prone to errors, where multiple frames should rather be used to minimize re-transmission overhead.

Learn more about encapsulation of packets here: https://brainly.com/question/22471914

The magnetic flux that passes through one turn of a 8-turn coil of wire changes to 5.0 Wb from 8.0 Wb in a time of 0.098 s. The average induced current in the coil is 140 A. What is the resistance of the wire

Answers

Answer:

Resistance is 1.75 ohms

Explanation:

Magnetic flux:

[tex]{ \phi{ = NBA}}[/tex]

N is number of turns, N = 8

B is magnetic flux

A is area of projection.

From faradays law:

[tex]E = - \frac{ \triangle \phi}{t} [/tex]

where E is the Electro motive force.

But E = IR

where I is current and R is resistance:

[tex]IR = \frac{( \phi_{1} - \phi _{2}) }{t} \\ \\ 140 \times R = \frac{8 \times (8 - 5)}{0.098} \\ \\ R = \frac{24}{0.098 \times 140} \\ \\ resistance = 1.75 \: ohms[/tex]

Write the equation in slope-intercept form
x-2y=4

Answers

Answer:

[tex]y=\frac{1}{2}x-2[/tex]

Explanation:

Slope-intercept form means we want the y to be by itself in the equation. Every thing we do will be about getting the y alone on the left side of the equation

To start we should move x to the left hand side. We can do this by subtracting x from both sides. That way, there is an x on the right, but not the left.

x-x-2y=4-x

this gives us

-2y=4-x

Great! So now what? Well, the y isn't by itself yet because it still is being multiplied by negative two (-2). In order to move it from the left side to the right side, we have to do the opposite of multiply; divide. So, we will divide both sides by -2

[tex]\frac{-2y}{-2} =\frac{4}{-2} -\frac{x}{-2}[/tex]

-2 divided by -2 is 1, 4 divided by -2 is -2, and -x divided by -2 is [tex]\frac{1}{2}x[/tex]

This gives us the answer:  [tex]y=\frac{1}{2}x-2[/tex]

Tips:

A negative divided by a negative is a positive ex: -4 divided by -2 is positive 2

If you are subtracting by a negative number, you are actually adding by a positive ex: 2-(-2) is actually 2+2

Don't be afraid to have fractions in your equations

Whatever you do to the one side of the equation, you must do it to the other side as well. Multiply the left side by 2? You HAVE TO multiply the right side by two as well. Add 3 to the right side? You HAVE TO add 3 to the left.

For problems like this (and when you have access to the internet), where you need to rewrite an equation, double check your work on desmos, which is an online graphing calculator. Input both the original equation and the equation you rewrote, and if they don't create the same line, you did something wrong.

Where is the center of mass of homogeneous body which has a regular ​

Answers

Following the definition of the center of mass, "In physics, the center of mass of a distribution of mass in space is the unique point where the weighted relative position of the distributed mass sums to zero."

(see explanation below)

Tay quay OB quay đều quanh trục cố định đi qua O với vận tốc góc không đổi ω. Con lăn A chuyển động trong rãnh thẳng đứng. Tại vị trí trên hình vẽ thì thanh OB thẳng đứng, OA có phương nằm ngang. Hãy xác định vận tốc góc thanh AB, vận tốc của con lăn A; gia tốc góc của thanh AB, gia tốc của con lăn A. Cho ω = 1,5 rad/s, r = 1 m.

Answers

sorry don’t understand your language.

Katie swings a ball around her head at constant speed in a horizontal circle with circumference 2.1 m. What is the work done on the ball by the 34.4 N tension force in the string during one half-revolution of the ball

Answers

Answer:

the work done on the ball is 0

Explanation:

Given the data in the question;

Katie swings a ball around her head at constant speed in a horizontal circle with circumference 2.1 m.

circle circumference = 2πr = 2.1 m

radius r will be; r = 2.1 m / 2π = 0.33 m

Tension force = 34.4 N

one half revolution means, displacement of the ball is;

d = 2r = 2 × 0.33 = 0.66 m

Now, Work done = force × displacement × cosθ

we know that, the angle between the tension force on string and displacement of object is always 90.

so we substitute

Work done = 34.4 N × 0.66 m × cos(90)

Work done = 34.4 N × 0.66 m × 0

Work done = 0 J

Therefore,  the work done on the ball is 0

A train moving west with an initial velocity of 20 m/s accelerates at 4 m/s2 for 10 seconds. During this tim
moves a distance of
meters.

Answers

Answer:

400m

Explanation:

[tex]x = v_{0}t + \frac{at^{2} }{2} \\x = 20*10+\frac{4*10x^{2} }{2} = 400m[/tex]

the lamp cord is 85cm long and comprises cupper wire. Calculate the wire‘s resistance?
radius of a wire is 1.8mmm,Use value of resistivity for Cu as 1.75 × 10-8Ωm.

Answers

Answer:

R = 0.0015Ω

Explanation:

The formula for calculating the resistivity of a material is expressed as;

ρ = RA/l

R is the resistance

ρ is the resistivity

A is the area of the wire

l is the length of the wire

Given

l = 85cm = 0.85m

A = πr²

A = 3.14*0.0018²

A = 0.0000101736m²

ρ = 1.75 × 10-8Ωm.

Substitute into the formula

1.75 × 10-8 = 0.0000101736R/0.85

1.4875× 10-8 = 0.0000101736R

R = 1.4875× 10-8/0.0000101736

R = 0.0015Ω

The resistance of the light bulb changed as the voltage (and current) changed. Why does this resistance change occur?

Answers

This resistance current is directly proportional to voltage and inversely proportional to resistance. In other words, as the voltage increases, so does the current. Hope this helps !!

Megan accelerates her skateboard from 0 m/s to 8 m/s in 2 seconds. What is the magnitude of the acceleration of the skateboard?
O 8 m/s^2
O 16 m/s^2
O 2 m/s^2
O 4 m/s^2​

Answers

Answer:

chk picture for eqn

Explanation:

what additional load will be required to cause the extension of 2.0cm when an elastic wire extend by 1.0cm when a load of 20g range from it

Answers

Answer:

The additional load is 20g

A cycle track is 500 metres long. A cyclist completes 10 laps (that is, he rides completely round the track 10 times).
a) How many kilometres has the cyclist travelled?
b) On average it took the cyclist 50 second to complete one lap (that it, to ride round just one).
(i) What was the average speed of the cyclist?
(ii) How long in minutes and seconds dit it take the cyclist to complete the 10 laps?
c) Near the end of the run the cyclist put on a spurt. During this spurt it took the cyclist 2 seconds to increase speed from 8 m/s to 12 m/s. What was the cyclist's acceleration during this spurt?

Answers

Explanation:

a) D_t = 500m*10laps

D_t = 5000m or 5km

b)

I) v = d/t

v = 500m/50s

v = 10m/s

ii) 10m/s = 5000m/t

t = 5000m/10m/s

t = (500s)*(1min/60s)

t = 8'20" or 8 mins and 20 sec

c) v_f = v_0 + a*t

v_f-v_0 = a*t

a = (v_f-v_0)/t

a = (12m/s-8m/s)/2s

a = (4m/s)/2s

a = 2m/s²

Part(a),

The distance travelled by the cyclist is 5 km.

Part(b),

(i) The average speed is 10 m/s

(ii) The time taken to cover 10 laps is 8 minutes and 20 seconds.

Part(c),

The acceleration is 2 m/s²

What is speed?

Speed is defined as the ratio of the time distance travelled by the body to the time taken by the body to cover the distance. Speed is the ratio of the distance travelled by time. The unit of speed in miles per hour.

a) The distance will be calculated as

D = 500m*10laps

D = 5000m or 5km

b) The average speed is calculated as,

I) v = d/t

v = 500m/the 50s

v = 10m/s

The time will be calculated as,

ii) 10m/s = 5000m/t

t = 5000m/10m/s

t = (500s)*(1min/60s)

t = 8'20" or 8 mins and 20 sec

The acceleration is calculated as,

c) vf = v0 + at

vf-v0 = at

a = (vf-v0)/t

a = (12m/s-8m/s)/2s

a = (4m/s)/2s

a = 2m/s²

To know more about speed and acceleration follow

https://brainly.com/question/14344386

#SPJ2

Other Questions
Date:04/09 Pages35 5) How does a common religion help the growth of nationality? Data stored on physical storage devices must do what before the processor can access it? Be converted to binary Be written to the hard drive Go into short-term memory Go from volatile to nonvolatile memory What is the area of a square with a side length of 32 yards? A company's stock price flucated over a period of four days. The table shows the change in stock price per day. The net change in the company's stock price over the four days Model of media richness Question on verbs in French Find the area of the triangle with vertices (0,0,0),(4,1,2), and (4,2,3). Ayer,yo al supermercado con mi mama The answer to this question Simplifie la phrase suivante pour qu'elle utilise l'infinitif au lieu du subjonctif.1. Il est naturel que j'aie mes propres opinions.a. Il est naturel d'avoir ses propres opinions.b.Il est naturel aie ses propres opinions.c.Il est naturel d'aie mes propres opinions.d.Il est naturel avoir mes propres opinions.Corrige la phrase suivante.2. Je doute que je cuisine mieux que Nathalie. a.Je doute pouvoir cuisiner mieux que Nathalie.b.Je doute de je cuisiner mieux que Nathalie.c.Je doute que Nathalie cuisiner mieux que moi.d.La phrase est dj correcte.3. Vous preferez que vous reveniez un autre jour ? a.Vous preferez revenir un autre jour ?b.Vous preferez de vous revenir un autre jour ?c.Vous preferez reveniez un autre jour ?d. La phrase est dj correcte. Choisis si la phrase suivante sera complotee avec un verbe a l'infuiltif ou au subjonctif. 4. On est surpris de ____________.a.savoir la veriteb.tu saches la verite5. Elle ne desire pas ______.a.fasse des etudes a l'universiteb.faire des etudes a l'universite Examples of a/an _______ observation are 37 m, 9.37 s, and 100 mph. You measure 49 turtles' weights, and find they have a mean weight of 80 ounces. Assume the population standard deviation is 6.1 ounces. Based on this, construct a 99% confidence interval for the true population mean turtle weight. Round your answers to 2 decimal places. What was the response of the world's nations to the Great Depression? Please explain the answer Use differentials to estimate the amount of paint needed to apply a coat of paint 0.07 cm thick to a hemispherical dome with diameter 50 m. (Round your answer to two decimal places.) Hey. I just need some advice. So I suck at math right like I dont know anything, or I should say I dont remember anything! So a little bit over the summer I have been doing Khan acadamey and what not. But I still cant seem to do anything right! So school here starts september 1st and Im gonna be a freshman in highschool. What do I do!!! Rewrite the following sentence;A. I am not interested in football. My brother is also not interested in football.B. Neither........ Question 8 If f (2) = (1 + 3) and g (2) VO+ 7, find g (f (x)). 9(f()) = 1 + 10 O g(f ()) = VI + 3 +7 Og(f (x)) = v= + 10 Og(f (2)) = 2? + 10 Frances bought a new dress that was discounted by 24%. she used the following expressions to find the price of the dress after the discount was applied What do you understand by moment of inertia and torque?Word limit 50-60Please don't copy from any sources. You can rewrite. Plagiarism will be check. Thank you.