Answer:
Answer:It is due to tyndall effect that the path of a light ray passing through a suspension is visible. The particles in suspension scatter the beam of light making it clearly visible.
Answer:
it is due to the Tyndall effect so the path of light is visible in a suspension but in solution the path of light is not visible
Calculate the momentum of a 4,800 kg car with a velocity of 25 m/s.
Answer:
p = 120000 kg · m/s
Explanation:
p = mv
p=momentum
m=mass
v=velocity
p = (4800)(25)
p= 120000 kg · m/s
Answer:
[tex]momentum = mass \times velocity \\ = 4800 \times 25 \\ = 120000 \: kgm {s}^{ - 1} [/tex]
What 3 factors should be considered when designing a lighting rod?
Explanation:
A lightning rod (US, AUS) If lightning hits the structure:-
It will preferentially strike the rod and be conducted to ground through a wire.
Instead of passing through the structure, where it could start a fire or cause electrocution.
The parts of a lightning protection system are air terminals (lightning rods or strike) and all of the connectors and supports to complete the system.
Sound travels slowest through gases _____________________. Group of answer choices because the molecules of gas are close together because gases are air because the molecules of gas are far apart because gases have the lowest temperature
A sound wave has a frequency of 192 Hz and travels the length of a football field at a speed of 338.5 m/s. what is the wavelength of the wave?
Explanation:
everything can be found in the picture
A 91.5 kg football player running
east at 2.73 m/s tackles a 63.5 kg
player running west at 3.09 m/s.
What is their velocity afterward?
Answer:
I'm pretty sure the velocity is 2.88 m/s
Explanation:
hope this is right good luck
Answer:
0.348
Explanation:
Acellus
(2²)⁴pepelelellelrle
Magali exerts a force of 4.5 N to slide her Blackberry across the table (so she can hide it from Hina!). If she does 2.7 J of work in the process, how far has the Blackberry moved?
Work is equal to the magnitude of the force multiplied by the displacement x. Assuming Magali is pushing the phone, so that the force and displacement point in the same direction, then the work done is positive, and
2.7 J = (4.5 N) x ==> x = (2.7 J) / (4.5 N) = 0.60 m
Even if she was pulling the phone instead, the displacement would be the same, but the work done would be negative and the force would point in the opposite direction, thus also having a negative sign:
-2.7 J = (-4.5 N) x ==> x = 0.60 m
The speed of light in vinegar is 2.30 x 10^8 m/s. Determine the index of refraction. (2
Answer:
[tex]n _{v} = \frac{c}{v} \\ = \frac{3 \times {10}^{8} }{2.30 \times {10}^{8} } \\ = 1.30[/tex]
This question involves the concept of refractive index.
The refractive index of the vinegar is "1.3".
What is the Refractive Index?The refractive index is defined as the ratio of the speed of light in air and the speed of light in the given medium which is vinegar here.
[tex]\eta = \frac{c}{v}[/tex]
where,
[tex]\eta[/tex] = refractive index = ?c = speed of light in air = 3 x 10⁸ m/sv = speed of light in vinegar = 2.3 x 10⁸ m/sTherefore,
[tex]\eta = \frac{3\ x\ 10^8\ m/s}{2.3\ x \10^8\ m/s}[/tex]
η = 1.3
Learn more about refractive index here:
https://brainly.com/question/23750645
#SPJ2
Ocean zones can be classified based on distance from Shore into intertidal,
costal ocean, and open oceans.
True or false ?
Answer:
I think true
Explanation:
I hope I'm right and I hope it helps
Answer:
true
Explanation:
basta yun yung sagot ko
Find new resistance of wire if it is stretched to twice its
original length. Original resistance was 20 ohm. Also how its
resistivity will change
Answer:
Original Length = L1
Stretched length =L2
From
R = pl/A
R=Resistance
p=Resistivity
A=Cross-sectional Area
l= length of wire
We can see that Resistance is directly Proportional to Length... Meaning that Resistance Increases also as Length increases.
R1/L1 = R2/L2
From the question... The key to note is this sentence
"The Stretched length is TWICE the Original Length"
Meaning
L2 = 2L1 (So replace L2 as 2L1 when solving)
R1=20ohms
Let R2 = k
Applying the formula
20/L1 = k/2L1
kL1 = 20x 2 L1
KL1 = 40L1
L1 cancels on both sides
k=40ohms.
So As the length doubled... The Resistance did too
from 20ohms to 40ohms
I need help pleaseee
Answer:
a refraction
b reflection
creflection
d refraction
brainliest plzz
6. Which of the following graphs correctly demonstrates the relationship between the
electromagnetic force and distance between charges?
Answer:
But where are the graphs
Coulomb's Law describes the relationship between electromagnetic force and the distance between charges.
What is the relationship between electromagnetic force and the distance between charges?The relationship between electromagnetic force and the distance between charges is described by Coulomb's Law, which states that the force between two charges is directly proportional to the product of the charges and inversely proportional to the square of the distance between them. Mathematically, Coulomb's Law is expressed as:
F = k (q₁x q₂) / r²
where F is the electromagnetic force, q1 and q2 are the charges, r is the distance between the charges, and k is the Coulomb constant.
This means that as the distance between two charges increases, the force between them decreases, and as the distance decreases, the force increases. The relationship between force and distance is inverse square, which means that the force decreases rapidly as the distance increases.
To know more about electric charges follow
https://brainly.com/question/874116
#SPJ6
Si un automóvil logra una potencia util promedio de 250kw y se sabe que tiene un rendimiento energético del 25%. ¿Cuanta energia total consume en 1 min? Exprese el resultado en kj
Answer:
W = 3.75 kJ
Explanation:
Power is defined by the relational
P = W / t
W = P t
the yield is 25% = 0.25
W = 0.25 Wo
W = 0.25 250 60
W = 3750 J
W = 3.75 kJ
Spaceship 1 and Spaceship 2 have equal masses of 150 kg. Spaceship 1 has an initial momentum magnitude of 900 kg-m/s. What is its initial speed?
A. 9 m/s
B. 6 m/s
C. 90 m/s
D. 60 m/s
Answer:
ans: 6 m/s
Explanation:
spaceship 1 has mass= 150kg
initial momentum of spaceship 1 = 900 kg•m/s
we know,
momentum = mass × velocity
so,
velocity = momentum/mass
= 900 / 150
= 6 m/s
since we know it was initial momentum so, velocity is initial speed,
Henry mixed salt and water together in a cup until he observed a clear solution. He measured the mass of the solution. Then he placed the cup outside for several sunny days during the summer. After a week, he observed that only solid salt remained in the cup and the mass had decreased. Henry concluded that a physical and chemical change occurred in this investigation.
Which statements correctly defend or dispute his conclusion?
He is correct. Dissolving salt in water is a physical change, but evaporating the water is a chemical change. Formation of a solid is evidence that a chemical change occurred.
He is correct. Evaporation is a physical change, but dissolving salt in water is a chemical change. The change in mass is evidence that a chemical change occurred.
He is incorrect. Dissolving salt in water and evaporation of the water are both physical changes. The reappearance of salt is evidence that the change was reversible by a physical change, so it could not be a chemical change.
He is incorrect. Dissolving salt in water and evaporation of the water are both chemical
Answer:
He is incorrect. Dissolving salt in water and evaporation of the water are both physical changes. The reappearance of salt is evidence that the change was reversible by a physical change, so it could not be a chemical change.
Answer:c
Explanation:
The lower the pH number is, the more ______ the solution.
Answer:
more acidic (less base)
hope this helps! :)
Air pollution is an example of a. The underground economy. B. An external shock. C. A nonmarket activity. D. A negative externality.
Answer:
D. A negative externality.
Explanation:
Particulate pollution is a form of pollution that is responsible for the degradation of the environment.
Particulate matter is also referred to as particle pollution or atmospheric aerosol particles and it can be defined as a complex microscopic mixture of liquid droplets and solid particles that are suspended in air.
An externality is typically an unwarranted cost or benefit by a manufacturer or producer of goods and services that affects a third party.
In Economics, an externality could either be positive or negative depending on its effect on a third party.
A negative externality arises when the production or consumption of a finished product or service has negative impact (cost) on a third party.
In conclusion, air pollution is an example of a negative externality because it causes harm to a third party.
6. A ball rolled 125 m from the top of a hill to the bottom of a hill. How long
did it take for the ball to roll if the average velocity was 5m/s? *
Si se desea construir un circuito con poca resistencia se debe colocar: En serie Mixto Paralelo Ninguna de las anteriores
Answer:
Parallel combination
Explanation:
When the two resistances are connected in parallel then the equivalent resistance is
[tex]\frac{1}{R}=\frac{1}{R'}+\frac{1}{R''}[/tex]
To get the minimum resistance of a circuit, the circuit components should be connected in parallel combination.
In the parallel combination, the voltage across each resistor is same and the current is divided in every resistance according to the resistances.
When a car velocity is negative and its acceleration is negative, what is happening to the cars motion?
Answer:
The car is speeding up in a negative direction.
Explanation:
A scientist is examining an unknown solid. Which procedure would most likely help determine a chemical property of the substance?
heating it to find the temperature at which it melts
exposing it to a flame to see if it catches on fire
hitting it with a hammer to determine if it breaks or bends
placing it in water to find out whether or not it dissolves
Answer:
hitting it with a hammer to determine if it breaks or bends
Answer:
exposing it to a flame to see if it catches on fire
Explanation:
A chemical property is when the matter changes into a different substance. This is true when you expose it to a flame because if a substance is burned, it will change into a new substance. All the other options are examples of physical changes.
-I also took the quiz and got 100%
Hope this helps!
Mike roller skates with a constant speed of 10 miles per hour. How long will he take to travel a distance of 15 miles.
Answer:
So every hour he makes 10 miles. So he would take 1 and a half hours to go to Mcdonalds 15 miles away.
Explanation:
[tex]\huge\boxed{{\textsf{90 minutes}}}[/tex]
We know that Mike's speed is [tex]\dfrac{10\ \text{miles}}{60\ \text{minutes}}[/tex] since there are [tex]60[/tex] minutes in an hour, and we know that MIke needs to travel [tex]15[/tex] miles. We'll model this using fractions:
[tex]\dfrac{10\ \text{miles}}{60\ \text{minutes}}=\dfrac{15\ \text{miles}}{x\ \text{minutes}}[/tex]
We can see that there is a [tex]2:3[/tex] ratio here, so we'll divide the left fraction by [tex]2[/tex] and multiply it by [tex]3[/tex] to get the right fraction.
[tex]\dfrac{10}{60}\Rightarrow\dfrac{5}{30}\Rightarrow\dfrac{15\ \text{miles}}{\boxed{90\ \text{minutes}}}[/tex]
calcula el peso de un perro cuya masa es de 25 kg en la tierra
Answer:
El peso = 245 Newton
Explanation:
Dados los siguientes datos;
Masa = 25 kg
Para encontrar el peso del perro en la tierra;
El peso se puede definir como la fuerza que actúa sobre un cuerpo o un objeto como resultado de la gravedad.
Matemáticamente, el peso de un objeto viene dado por la fórmula;
[tex] El \; peso = mg [/tex]
Dónde;
m es la masa del objeto.
g es la aceleración debida a la gravedad.
Sabemos que la aceleración debida a la gravedad es igual a 9,8 m / s² en el planeta Tierra.
Sustituyendo en la ecuación, tenemos;
[tex] W = 25 * 9.8[/tex]
El peso = 245 Newton
Señala cual de las siguientes propiedades de una sustancia son propiedades características= masa densidad volumen belleza conductividad eléctrica
Answer:
i) densidad
ii) conductividad eléctrica
Explanation:
Las propiedades características de una sustancia se denominan también propiedades intrínsecas. Estas son propiedades que no dependen de la cantidad de sustancia presente.
Las propiedades características se pueden utilizar para identificar una sustancia porque son propiedades que siempre debe exhibir la sustancia.
Entre las opciones, podemos encontrar las siguientes sustancias características;
i) densidad
ii) conductividad eléctrica
A resistor of 500Ω and one of 2000Ω are placed in series with a 60V supply. What will be the reading on a voltmeter of internal resistance 2000Ω when placed across (i) 500Ω resistor and (ii) 2000Ω resistor?
Answer: 10 V, 40 V
Explanation:
Given
Resistors are [tex]500\Omega[/tex] and [tex]2000\Omega[/tex]
Power supply [tex]V=60\ V[/tex]
Voltmeter internal resistance [tex]r=2000\ \Omega[/tex]
When it connected around [tex]500\Omega[/tex] resistance, effective resistance becomes
[tex]\Rightarrow \dfrac{1}{R}=\dfrac{1}{500}+\dfrac{1}{2000}\\\\\Rightarrow R=\dfrac{2000}{5}\\\\\Rightarrow R=400\ \Omega[/tex]
Total resistance in series [tex]R_{net}=2400\ \Omega[/tex]
Current in circuit
[tex]I=\dfrac{60}{2400}=\dfrac{1}{40}\ A[/tex]
Voltage around [tex]500\Omega[/tex] resistance is
[tex]V=\dfrac{1}{40}\times 400\\\\V=10\ V[/tex]
(B) when voltmeter is connected around [tex]2000\Omega[/tex] resistor
Net resistance around it
[tex]\Rightarrow \dfrac{1}{R}=\dfrac{1}{2000}+\dfrac{1}{2000}\\\\\Rightarrow R=1000\ \Omega[/tex]
Total resistance [tex]R_{net}=1500\ \Omega[/tex]
Current in circuit
[tex]I=\dfrac{60}{1500}=\dfrac{1}{25}\ A[/tex]
Voltage around [tex]2000\Omega[/tex] resistor
[tex]V=\dfrac{1}{25}\times 1000\\\\V=40\ V[/tex]
Arches National Park is a desert landscape located in Utah. The park is filled with arches that have been formed by nature. The arches were once solid rock. Over time, extreme temperature changes and windy conditions have caused pieces of rock to crumble and blow away, leaving holes in the rock and forming the arches. Which of these processes is responsible for the formation of the arches?
a.cooling magma
b.weathering and erosion
c.compaction and cementation
d.increased geological pressures
explain the derivation of Newton's third and second law.
Answer:
Consider an isolated system of 2 bodies A & B. An isolated system means where there is no external force acting.Now let F be the force acting on B by A & F be the force acting on A by B.Now rate of change of momentum of A =dpA/dt and rate of change of momentum of B =d pB/dt
thus FAB=d pB/dt (i)......
FBA=dpA/dt (ii)........
Adding 1 and 2 we get FAB+FBA=d pB/dt+dpA/dt =d(pB+pA)/dt
But if no force is applied momentum will also be 0 because no velocity will be there so rate of change of momentum will also be 0
thus d(pA+pB)/dt=0
therefore FAB+FBA=0
or,FAB=-FBA
(3RD LAW OF MOTION)
how can you reduce output voltage to 6v in transformers if the input voltage is 240v
Answer:
[tex]N_P = 40\ N_S[/tex]
To reduce the output voltage to 6v in transformers if the input voltage is 240v, we need to have 40 times as many turns in the primary coil as there are in the secondary coil.
Explanation:
The change in voltage of a transformer depends upon the turns ratio of the transformer between secondary and primary coil. Following formula can be used to determine the turns ratio in this case:
[tex]\frac{N_P}{N_S} = \frac{V_P}{V_S} \\\\[/tex]
where,
[tex]N_P[/tex] = No. of turns in the primary coil
[tex]N_S[/tex] = No. of turns in the secondary coil
[tex]V_P[/tex] = voltage in the primary coil = 240 V
[tex]V_S[/tex] = voltage in the secondary coil = 6 V
Therefore,
[tex]\frac{N_P}{N_S} = \frac{240\ V}{6\ V} \\\\N_P = 40\ N_S[/tex]
To reduce the output voltage to 6v in transformers if the input voltage is 240v, we need to have 40 times as many turns in the primary coil as there are in the secondary coil.
How to solve the equation of power ?
Answer:
OK HERE
Explanation:
When raising a power to a power in an exponential expression, you find the new power by multiplying the two powers together. For example, in the following expression, x to the power of 3 is being raised to the power of 6, and so you would multiply 3 and 6 to find the new power.
1. 10. waves break on the beach in 2.0 min. What is the frequency in hertz of these waves (cycles per
second)? What is the time between successive waves, in seconds?
Answer:
there it is fella tried o. ma own consciousness
