In the image below, a free-body diagram represents the forces of several vehicles driving across a bridge. Assume that the bridge is in statio equilibrium and that it has zero weight, and solve for the unknown reaction force
A. 10,800 N
B. 65,200 N
C. 120,200 N
D. 53,400 N​

Answer:

False.

Explanation:

A warm up is stretching in the beginning.

Answer:

w = 0.01 t⁻²   rad/h

Explanation:

Let's use trigonometry to find the elevation angle of the telescope, we assume that the rocket remains fixed in the telescope.

        tan θ = CO / CA

the adjacent leg is CA = 16 km = 16 10³ m

Let's use kinematics to find the height of the rocket

          v = y / t

          y = v t

this height is equal to the opposite leg

          CO = v t

we substitute

         tan θ = vt / 16

         tan θ = 1200/16 t

         tan θ = 75 t

         θ = tan⁻¹ ( 75 t )

speed is defined by

          w = dθ/dt

          w = [tex]\frac{1}{1 + (75 t)^2} \ 75[/tex]  

as time increases we can neglect the 1 of the denominator

          w = 1/75 t²

          w = 0.0133 t⁻²

Using three significant figures

           w = 0.01 t⁻²   rad/h

for this answer the time must be given in hours

Explanation:

p = F /A

F = P×A

F = 30,000 Pa / 0.1 m²

F = 300,000 N

Answer:

cần cung cấp 70 độ vì nước sôi ở 100°C

Explanation:

Answer:

The resistance of a thin wire is greater than the resistance of a thick wire because a thin wire has fewer electrons to carry the current. The relationship between resistance and the area of the cross section of a wire is inversely proportional .

The best way to think about this is:

A thick/wide road, with many lanes, can carry more cars than a thin/narrow road, with only one or two lanes.

Answer:

But negative acceleration means that the rate of change of velocity is negative or velocity decreases. Example: (1) When we apply brakes in a moving car, then negative acceleration acts on it and the car stops. (2) When we throw a ball upwards, then also negative acceleration acts on it.

Explanation:

If it helps you mark me as a brainleast

MATHEMATICALLY A NEGATIVE ACCELERATION MEANS YOU WILL SUBTRACT FROM THE CURRENT VALUE OF THE VELOCITY.

The three dimensional space of a body is called volume

Answer:

Don't Forget To Follow, Brainliest, And Give Me Heart :)

Answer:

3.8 x 10^-5

Explanation:

all you doing is putting it in the standard form I hope this help

Answer:

The average velocity of an object is its total displacement divided by the total time taken. In other words, it is the rate at which an object changes its position from one place to another.

Explanation:

Average velocity is a vector quantity. The SI unit is meters per second. However, any distance unit per any time unit can be used when necessary, such as miles per hour (mph) or kilometer per hour (kmph)

Answer:

the ratio of total displacement by total time taken

Answer:

0.80 m

Explanation:

Neglecting friction, the total mechanical energy of the pendulum is constant.

E = K + U where K = kinetic energy and U = potential energy.

At its release point of 0.80 m, the pendulum bob has a mechanical energy which is equal to its potential energy, since, its initial kinetic energy is zero. By the time the bob swings to the other end, it has a mechanical energy equal to it initial potential energy since total energy is conserved.

Neglecting friction, the pendulum bob would swing back to its original height of 0.80 m since the total mechanical energy is conserved and at its highest point, it is purely potential energy.

So, the height the pendulum bob swings to after release from a height of 0.80 m neglecting fiction is 0.80 m.

Answer:

False -> negative charge

Answer:

false

Explanation: electrons are negative charges

protons are positive charges

Answer:

(a)  333.77 J

(b) 237.85 J

(c) 4763.77 J

(d) 4667.85 J

Explanation:

Temperature of source, TH = 314 K

Temperature of A, Tc = 292 K

Temperature of B, Tc' = 298 K

heat taken out, Qc = 4430 J

Let the heat deposited outside is QH and QH' by A and B respectively.

[tex]\frac{Q_H}{Q_c}=\frac{T_H}{T_c}\\\\Q_H = \frac{4430\times314}{292}=4763.77 J[/tex]

Now

[tex]\frac{Q_H'}{Q_c}=\frac{T_H}{T_c'}\\\\Q_H' = \frac{4430\times314}{298}=4667.85 J[/tex]

(a) Work done for A

W = QH - QC = 4763.77 - 4430 = 333.77 J

(b) Work done for B

W' = QH' - Qc = 4667.85 - 4430 = 237.85 J

(c) QH = 4763.77 J

(d) QH' = 4667.85 J

Answer:

the process of comparing unknown quantities with known standards quantities are known as measurement

Answer:

Resistance is defined as the property of a conductor to resist the flow of charges through it. The resistance of conductor is numerically given as the ratio of potential difference across its length to the current flowing through it.

Explanation:

Answer:

1) The kinetic energy of the object after it drops for 2.0 seconds is approximately 384.9 Joules

2) The potential energy of the object after it drops for 2.0 seconds is approximately 204 J

Explanation:

1) The given mass of the object, m = 2.0 kg

The height from which the object is dropped, h = 30 m

The kinetic energy of the object after it drops for 2.0 seconds = Required

Kinetic energy, K.E. = (1/2)·m·v²

Where;

v = The velocity of the object

The kinematic equation for finding the velocity of the object is presented as follows;

v = u + g·t

Where;

u = The initial velocity of the object = 0

g = The acceleration due to gravity of the object ≈ 9.81 m/s²

t = The time of motion of the object = 2.0 seconds

∴ The velocity after 2 seconds, v ≈ 0 + 9.81 m/s² × 2 s = 19.62 m/s

The kinetic energy, K.E. after 2 seconds as the object drops is given as follows;

[tex]K.E._{(after \ two \ seconds)}[/tex] = (1/2) × 2.0 kg × (19.62 m/s)² = 384.9444 J ≈ 384.9 J

2) The total energy, M.E. of the object at the top, h = 30 m, u = 0, is given as follows;

The total mechanical energy, M.E. = P.E. + K.E.

M.E. = m·g·h + (1/2)·m·u²

∴ M.E. = 2.0 kg × 9.81 m/s² × 30 m + 0 = 588.6 J

M.E. = 588.6 J

Given that the total mechanical energy, M.E., is constant, we have;

At 2.0 seconds, M.E. = 588.6 J , K.E. ≈ 384.9 J, P.E. = M.E. - K.E.

∴ P.E. = 588.9 J - 384.9 J ≈ 204 J

The potential energy after it drops 2.0 seconds, P.E. ≈ 204 J

Answer:

Because matter has been squeezed into a tiny space.

Explanation:

According to NASA, this can happen when a star is dying.

A black hole has no more gravity than the same amount of matter in any other form.

But remember that the gravitational forces are stronger as you get closer to the center of the body. The mass of a black hole is packed into such a small size (theoretically zero !) that you can get very close to its center. THAT'S where its gravity is hugely strong.

First half:

50 km at 50 km/hr ... 1 hour

Second half:

50 km at 100 km/hr ... 1/2 hour

Total distance = 100 km

Total time = 1.5 hours

Average speed = (100 km) / (1.5 hrs)

Average speed = 66 and 2/3 km/hr

Average velocity = 66 and 2/3 km/hr East

The average velocity of the car would be 66.67 Kilometers / hours.

The total displacement covered by any object per unit of time is known as velocity. It depends on the magnitude as well as the direction of the moving object.

As given in the problem a car travels 100 km to the east. If the first half of the distance is driven at 50 km/h and the second half at 100 km/h,

The average velocity of the car = Total displacement / total time

                                                     =100 / 1.5

                                                     =66.67 Kilometers / hours

Thus, the average velocity of the car would be 66.67 Kilometers / hours.

To learn more about Velocity from here, refer to the link given below;

brainly.com/question/18084516

#SPJ2

Answer with Explanation:

Let me answer this in a simple way, since the density of stone is greater than that of water, the stone sinks as the weight of the stone is greater than the weight of water displaced by it. But the ship is designed in such a way that the relative density of the ship always becomes less than that of water. Therefore, the weight of the water displaced becomes equal to the total weight of the ship and thus it floats.

There are many other ways to explain this but this should give you the general idea.

Answer:

It is not solid under normal conditions

Mercury differs from other metals as It is not solid under normal conditions. It is the only metal that is liquid at room temperature, therefore the correct answer is option C

Anything which has mass and occupies spaces is known as matter, mainly there are four states of matter solid liquid gases, and plasma.

These different states of matter have different characteristics according to which they vary their volume and shape.

Because it is not solid under normal circumstances, mercury is different from other metals. Because it is the only metal that is liquid at room temperature,

Thus the correct answer is option C

Learn more about the matter here

brainly.com/question/9402776

#SPJ2

We know

[tex]\boxed{\sf Spring\:constant(K)=\dfrac{F}{x}}[/tex]

[tex]\\ \sf\longmapsto K=\dfrac{1}{0.5}[/tex]

[tex]\\ \sf\longmapsto K=2N/m[/tex]

Answer:

what do u need help with

Explanation:

Pа: 5. Mass of the earth is 6x10-kg and its radius is 6400km. What is the mass of a man weighting 977N? (99.99kg) ma. Orth be​.

Answer:

Explanation:

There is no pressure of your feet on the scales, and no pressure of the floor on the scales, so the scales will read zero*. Hence, your weight, in a freely falling lift is zero

Answer:

If effort distance was 4 times, efficiency would be 100%.

Since it takes 5 times for effort distance, efficiency drops to output/input

output is 1*F

input is (1/4*F)*5

so: F/1/5*F/4 = 4F/5F = .8 or 80%

The efficiency of the lever is 80%.

To calculate the efficiency of the lever, we can use the formula for mechanical advantage and efficiency.

Mechanical Advantage (MA) is the ratio of the load (L) to the effort (E) in a lever system:

MA = Load / Effort

Given that the load is four times the effort applied:

Load = 4 * Effort

Also, the effort distance (dEffort) is five times the load distance (dLoad):

dEffort = 5 * dLoad

Now, we can write the formula for efficiency (η) of a lever system:

Efficiency (η) = (Mechanical Advantage / Ideal Mechanical Advantage) * 100%

The Ideal Mechanical Advantage (IMA) is the ratio of the effort distance to the load distance:

IMA = dEffort / dLoad

Substitute the given values into the IMA equation:

IMA = (5 * dLoad) / dLoad

IMA = 5

Now, we can calculate the Mechanical Advantage (MA) using the relationship between the load and effort:

MA = Load / Effort

MA = (4 * Effort) / Effort

MA = 4

Finally, we can calculate the efficiency (η):

Efficiency (η) = (Mechanical Advantage / Ideal Mechanical Advantage) * 100%

η = (4 / 5) * 100%

η = 0.8 * 100%

η = 80%

The efficiency of the lever is 80%.

To know more about efficiency here

https://brainly.com/question/31458903

#SPJ2

Answer:

0.25p.a

Explanation:

force=15N area=60m²

so pressure =force/area =15N/60m²=0.25p.a

Answer:

96 meters

Explanation:

d = st

d = (8 m/s)(12 s)

d = 96 m