(a) θ5 in the air is 56.9° and (b) θ4 in the bottom material 35.30°. Normally, a light beam that strikes an angle on a prism's refracting face emerges from the opposite face.
How to calculate?(a) Approximating n=1 for air, we have
n1. sinθ1 = (1)sinθ5 ⇒56.9°=θ5
and with the more accurate value for n air in Table below, we obtain 56.80.(b) Equation n1 sinθ c =n2 sin 90° leads to,
n1 sinθ 1=n2 sinθ2 =n3 sinθ 3 =n4 sinθ 4
so that. θ4 =sin −1( n1/n4.sinθ 1 )=35.30° .
What does angle of incidence mean?The angle of incidence is formed by a line drawn perpendicular to the reflecting barrier and the wave's direction of motion.
Is the incidence angle of refraction?Refraction Depending on the Refractive Indices in the Two Media and the Angle of Incidence. Snell's law states that the angle of incidence, I and the proportion of the refractive indices of the two media that make up the interface determine the angle of refraction, r.
Learn more about refraction here:
https://brainly.com/question/14760207
#SPJ4
A uniform plane wave with parallel polarization is propagating in a lossless dielectric medium (l is € 1), and is incident obliquely onto a plane boundary with another lossless dielectric medium (u 2, E 2). (30%) (a) Derive the Snell's laws of reflection and refraction in terms of the refractive indices and angles. (b) Derive the general expressions for the reflection and the transmission coefficients of the EM field. Find such expressions in terms of the refractive indices if both media are nonmagnetic, i.e., M F M 240. (c) Derive the general expression for the Brewster angle. Find such an expression in terms of the refractive indices if both media are nonmagnetic. (d) Prove that, under the condition of no reflection, the sum of the Brewster angle and the angle of refraction is 90° if both media are nonmagnetic. (e) For total reflection to occur, find the condition for the medium property and the critical angle.
Transmission coefficients are used in physics and electrical engineering when considering wave propagation in discontinuous media. The snells law is n₁sinθ1 = n₂sinθ2
The transmission coefficient describes the amplitude intensity or total power of the transmitted wave relative to the incident wave. The transmission coefficient is defined as the ratio of the transmitted particle flux to the incident particle flux and depends on the incident energy.
The sum of the reflected and transmitted energy must equal the total incident energy, so the transmission coefficient is calculated simply by subtracting the reflection coefficient. The ratio of the reflected wave amplitude to the incident wave amplitude is called the reflection coefficient.
Learn more about The transmission coefficients here:- https://brainly.com/question/9323897
#SPJ4
What is the Force of Gravity acting on the object in the diagram?
The force of gravity acting on the 23 Kg object in the diagram is 225.4 N
How do I determine the force of gravity?The force of gravity is defined as follow:
Force of gravity (F) = mass (m) × acceleration due to gravity (g)
Using the above formula, we can easily obtain the force gravity acting on the 23 Kg object. This is shown below:
Mass (m) = 23 KilogramsAcceleration due to gravity (g) = 9.8 m/s²Force of gravity (F) =?Force of gravity (F) = mass (m) × acceleration due to gravity (g)
Force of gravity = 23 Kg × 9.8 m/s²
Force of gravity = 225.4 N
Thus, from the calculation made above, we can conclude that the gravitaional force is 225.4 N
Learn more about force:
https://brainly.com/question/12163222
#SPJ1
if an object producing sound is moving away from you, you would observe a wavelength than an object moving toward you. group of answer choices
If an object producing sound is moving away from us, the wavelength of the sound heard is longer than the actual wavelength. The conclusion is from the concept of Doppler effect.
What is the Doppler effect?The Doppler's effect is a phenomenon when the source of a wave and an observer move relative to each other, the frequency heard is not the same with the actual frequency.
The equation of the Doppler effect is
f₀ = [(v ± v₀)/(v ± vs)] × fs
Where
f₀ = observer frequency of soundv = speed of sound waves (340 m/s)v₀ = observer velocityvs = source velocityfs = actual frequency of sound wavesNote:
v₀ (+) if the observer moves closer to the sound source.vs (+) if the sound source moves away from the observer.When an object producing sound is moving away from us, the frequency of the sound we heard changed.
Let's say we are at rest, it means v₀ = 0. The sound source is moving away makes vs (+).
With the Doppler's effect, we get
f₀ = [(v+0) / (v+vs)] × fs
f₀/fs = v/(v+vs)
v < v+vs
f₀ < fs
The frequency of sound we heard is lower that the actual frequency.
The wavelength is inversely proportional to the frequency. It is described in the equation:
λ = c/f
It means that the lower the frequency, the longer the wavelength.
Hence, the phenomenon which the wavelength of the sound we heard is longer than the actual wavelength when the sound source is moving away from us is called the Doppler's effect.
Here is the group of answer choices:
(a) Band width
(b) Doppler's effect
(c) Sound refraction
(d) Vibrations
Learn more about Doppler's effect here:
https://brainly.com/question/29672712
#SPJ4
One of the most controversial ideas to come out of instinct theories of aggression was Lorenz's proposal that society provide acceptable ways of permitting , or the process of discharging built-up aggressive energy.
The general instinct hypothesis, which contends that people are physiologically predisposed to or possess inclinations for violent behaviours, is known as the instinct theory of aggression in psychology.
This theory is more focused on aggression. The instinct theory of aggressiveness holds that human aggression is akin to sex and hunger, and that it can only be regulated rather than eradicated.In an effort to understand why we become aggressive and whether that behaviours can be altered, psychologists have developed three primary theories of aggression. Although many hypotheses have been put out, these three have proven most reliable and are crucial to comprehending the origins of violence. These hypotheses comprise as,
Adversity theory based on instinctTheory of Frustration and AggressionTheory of Social LearningTo know more about theory of aggression
https://brainly.com/question/3197702
#SPJ4
for the circuit below all values are rms with a source frequency of 60 hertz. the generator impedance is negligible (0 w). calculate the value of ib and and determine the value of vb-n. now, calculate the rms values of apparent, real and reactive power of zb. (show units for all)
The reactive power of the branch (Qb) can be calculated from its voltage and current 676.16 VA.
What is reactive power?Reactive power is the power in an AC circuit that is required to establish and maintain a voltage across a load. It is associated with the storage and release of energy in the form of electric and magnetic fields. Reactive power does not contribute to the actual work output of a system and is measured in Volt-amperes reactive (VARs). Power factor is a measure of reactive power relative to the total power in a system.
Source frequency = 60 Hz
Generator impedance = 0 W
Circuit:
Vg = 170 V
R1 = 10 Ω
R2 = 20 Ω
Zb = 20 + j10 Ω
The current flowing through the generator (Ig) and the branch (Ib) can be calculated from Ohm's Law:
Ig = Vg/R1 + Vg/R2 = 170/10 + 170/20 = 17 A
Ib = Ig - Vg/Zb = 17 - 170/(20 + j10) = 17 - 16.4 + j4.4 = 0.6 + j4.4 A
Since Ib is a complex number, we can find its magnitude (|Ib|) and angle (θ):
|Ib| = √(0.6² + 4.4²) = 4.46 A
θ = tan⁻¹(4.4/0.6) = 80.16°
The voltage across the branch (Vb-n) can be calculated using Ohm's Law:
Vb-n = Ib × Zb = (0.6 + j4.4) × (20 + j10) = -8.4 + j74.4 V
The apparent power of the branch (Sb) can be calculated from its voltage and current:
Sb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = -45.48 + j367.04 VA
The real power of the branch (Pb) can be calculated from its voltage and current:
Pb = Vb-n × Ib = (-8.4 + j74.4) × (0.6 + j4.4) = -45.48 - j367.04 W
The reactive power of the branch (Qb) can be calculated from its voltage and current:
Qb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = 676.16 VA
To learn more about reactive power
https://brainly.com/question/23230296
#SPJ4
what is the length of the y component shown below?
The length of the y component shown is C. 2.0.
How to find the length ?We are given the angle of the vector, and the length of one of the components of the vetor. Given the angle we have, the available component is the hypotenuse. The y component that we are to find, will then be the opposite or perpendicular component.
To solve for the length of the y - component therefore, the useful operation would be the Sin function.
The length of the y - component would be:
Sin 42 ° = Opposite / Hypotenuse
Sin 42 ° = y component / Hypotenuse
y - component = Sin 42 ° x Hypotenuse
y - component = Sin 42 ° x 3
y - component = 0. 6691 x 3
y - component = 2. 0
In conclusion, the y - component is 2.0.
Find out more on y-component at https://brainly.com/question/3387587
#SPJ1
Full question is:
What is the length of the y-component of the vector shown below?
A. 2.2 B. 3 c. 2.0 D. 2.7apply the loop rule to loop 2 (the smaller loop on the right). sum the voltage changes across each circuit element around this loop going in the direction of the arrow. remember that the current meter is ideal.express the voltage drops in terms of vb , i2 , i3 , the given resistances, and any other given quantities.
The voltage drops in terms of vb , i2 , i3 , the given resistances, and any other given quantities.ΣΔV = 0 = I3 ⋅ R3 - I2 ⋅ R2.
When applying Kirchhoff's second rule the loop rule we need to identify closed loops and decide whether to loop clockwise or counterclockwise. For example, in Figure 3 the loop was traversed in the same direction as the current.
Loop 1 is the full loop and Loop 2 is the small loop on the right. To apply the loop rule, add all those voltage changes. Kirchhoff's Second Law, also known as Kirchhoff's Voltage Law states that the sum of all voltages around the closed loop of any circuit must be zero. This is a result of charge conservation and energy conservation.
Learn more about The loop rule here:- https://brainly.com/question/15705903
#SPJ4
(1) A table tennis ball is dropped
onto the floor from a height of
4m and it rebounds to a height of
3m. If the time of contact with the floor is 0.01s, what is the magnitude and direction of the acceleration during the contact.
Answer:
Here, h1=4.00m,h92)=3.00m,Delta t =0.01 s.Letv1 be the velocity of the ball (actind downwards) just before striking the floor an dv20 be the velocity of the ball (acting upwaeds) ust after striking the floor. Then, change in velocity of the ball in time Δtv2−(−v1)v2+v1
:. acceleration, a=v2+v1Δt ..(i)
When body falls from height h1,
then u=o,v1,a=gandS=h1
As, v21=u2+2aS,
:. v_(1) ^(2) =0 + g h_(10 or v12–√gh1
Taking motion of the ball after striking the floor, then u=v2,v=0,a=−g,S=h2
As, v2=u22as,∴v21=0+2gh1orv_(1) =sqrt 32 g h_(1)Tak∈gmotionoftheballa>erstrik∈gthe⌊,⌋thenu=v_(2), v=0, a=- g, S=h_(2)As,v2=u2+2aS,wehave0 = v_(2)^(2) +2 (-g) h_92) otr v2=2–√gh2
Putting values in (i) we get,
a=2–√gh2+2–√gh1Δt)
a=2–√×9.8×3+2–√×9.8×40.01
= 1652m/s2.
Explanation:
based on the graphic, in what part of the electromagnetic spectrum does vegetation have the strongest response?
Between 400 nm and 700 nm of the electromagnetic spectrum, vegetation has the strongest response.
The electromagnetic spectrum travels in waves and spans an extensive spectrum from very long radio waves to very brief gamma rays. The human eye can simplest come across only a small portion of this spectrum called visible light.
In order from maximum to lowest power, the sections of the EM spectrum are named: gamma rays, X-rays, ultraviolet radiation, visible mild, infrared radiation, and radio waves.
In a tumbler, the purple mild travels the fastest, and the violet light travels the slowest of all seven hues. Velocity and wavelength are without delay proportional.
Learn more about Electromagnetic spectrum here:-https://brainly.com/question/23423065
#SPJ4
For a particular nonlinear spring, the relationship betweem the magnitude of the applied force F and the resultant displacement x from equilibrium is given by the equation F = k x^2 What is the amount of work done by stretching the spring a distace x0? A) kx0^3 B) (1/2)kx0 C) (1/2)kx0^3 D) (1/3)kx0^2 E) (1/3)kx0^3
To get the work, you have to integrate the force as a function of [tex]$x$[/tex] from zero displacement to Xo
[tex](Integral of) $\mathrm{k} \mathrm{x}^{\wedge} 2 \mathrm{dx}$ from 0 to $\mathrm{Xo}_{\mathrm{o}}=(1 / 3) \mathrm{k}\left(\mathrm{Xo}^{\wedge}\right)^{\wedge} 3$[/tex]
The work done by stretching the spring to the given distance is [tex]W=\frac{k x_0}{3}[/tex]
The given parameters:
- Applied force on the spring [tex]$=F$[/tex]
- Extension of the spring [tex]$=x_0$[/tex]
The work done by stretching the spring to the given distance is calculated as follows;
[tex]W=\frac{k x_0}{3}[/tex]
[tex]$$\begin{aligned}& W=\int_{x_a}^{x_b} F d x \\& W=\int_{x_a}^{x_b} k x^2 d x \\& W=k \int_{x_a}^{x_b} x^2 d x \\& W=k\left[\frac{x^3}{3}\right] \\& W=k\left[\frac{x_b-x_a}{3}\right] \\& W=k\left[\frac{x_0-0}{3}\right] \\& W=\frac{k x_0}{3}\end{aligned}[/tex]
Thus, the work done by stretching the spring to the given distance is
[tex]W=\frac{k x_0}{3}[/tex]
measure of energy transfer that occurs when an object is moved over a distance by an external force at least part of which is applied in the direction of the displacement.
To learn more about work done visit:
https://brainly.com/question/13662169
#SPJ4
A(n) ____________________ is a dynamic variable on the free store without any pointer pointing to it.
A inaccessible object is a dynamic variable on the free store without any pointer pointing to it.
How to find the height of an inaccessible object using sextant?Utilize the sextant's arc to determine the angle. By dividing the object's distance from the point of observation by the tan of the angle you calculated, you may use a scientific calculator to get the object's height.
How can heights and distances that are absent or unavailable be measured?The measuring of heights and distances that are unreachable is made easier by right-triangle trigonometry. By drawing a right triangle with the unknown height or distance as one of its sides and a known side and angle on the other, it is possible to determine the unknown height or distance.
To know more about inaccessible object visit:
https://brainly.com/question/21989844
#SPJ4
Answer:
dynamic variable
which of the following sequences lists methods for determining distance in the correct order from nearest to farthest?
Parallax, main-sequence fitting, cepheid variables, Tully-Fisher relation, and Hubble's law are the sequence lists methods for determining distance.
Parallax is the closest method for determining distance. This method uses the principle of triangulation to measure the distance of a nearby star relative to Earth. Main-sequence fitting is another method used to measure the distance of stars. This method compares the brightness of a star to other stars of known distance and luminosity to determine its distance.
Cepheid variables are stars whose brightness varies in a predictable way over time. This method uses the period of the star's brightness to determine its intrinsic luminosity, and then its distance. The Tully-Fisher relation is a method for measuring the distance of galaxies. This method uses the rotation speed of the galaxy and its brightness to calculate its distance.
Finally, Hubble's law is the most distant method for determining distance. This law states that the farther away a galaxy is, the faster it moves away from us. This allows us to calculate the distance of galaxies by measuring their rate of recession.
For more questions like Hubble's law click the link below:
https://brainly.com/question/29869676
#SPJ4
aphasia
Due to an automobile accident, Jenny suffered damage to her cerebral cortex in Broca's area. Jenny is most likely to experience:
Due to an automobile accident, Jenny suffered damage to her cerebral cortex in Broca's area. Jenny is most likely to experience: aphasia.
Aphasia is the inability to understand or form language due to damage to certain areas of the brain The main causes are stroke and head trauma. Although the prevalence is difficult to determine, aphasia due to stroke is estimated at 0.1-0.4% in the Global North. Aphasia can also be the result of a brain tumor, brain infection, or neurodegenerative disease (such as dementia).
To be diagnosed with aphasia, communication after an acquired brain injury Speech or language must be significantly impaired in one (or more) of the four aspects of Alternatively, in the case of progressive aphasia, it must have decreased significantly over a short period of time. The four dimensions of communication are auditory comprehension, verbal expression, reading and writing, and functional communication.
Learn more about Aphasia here : https://brainly.com/question/4045064
#SPJ4
