If most wildfires are suppressed (all fires are put out) for many years, how does the risk of wildfire in the area change in the future?

There will be a higher risk of wildfires
There will be a lower risk of wildfires
There is no difference in risk

Explain your answer.

Answer:

14.506°C

Explanation:

Given data :

flow rate of water been cooled = 0.011 m^3/s

inlet temp = 30°C + 273 = 303 k

cooling medium temperature = 6°C  + 273 = 279 k

flow rate of cooling medium = 0.02 m^3/s

Determine the outlet temperature

we can determine the outlet temperature by applying the relation below

Heat gained by cooling medium = Heat lost by water

= ( Mcp ( To - 6 )  =  Mcp ( 30 - To )

since the properties of water and the cooling medium ( water ) is the same

= 0.02 ( To - 6 ) = 0.011 ( 30 - To )

= 1.82 ( To - 6 ) = 30 - To

hence To ( outlet temperature ) = 14.506°C

Answer:

8*10000+3*1000+1*00+2*10+2

Explanation:

Answer:

movement in clockwise direction.

Explanation:

The following parameters or information are given from the question above, they are:

[1]. There are two identical keys, [2]. two out of the five keys are attached to 6cm from the pivot, [3]. three keys out of the five keys on the right are attached 5 cm.

Therefore, considering the moment of force, the two keys on the left = 2 × 6 = 12.

Also, considering the moment of force, the 3 keys on the right = 3 × 5 = 15.

Therefore, we have more weight on the right keys. So, in order to balance the force there must be movement in clockwise direction.

Answer:

a) 159.07 MPa

b) 10.45 MPa

c) 79.535 MPa

Explanation:

Given data :

length of cantilever beam = 1.5m

outer width and height = 100 mm

wall thickness = 8mm

uniform load carried by beam  along entire length= 6.5 kN/m

concentrated force at free end = 4kN

first we  determine these values :

Mmax = ( 6.5 *(1.5) * (1.5/2) + 4 * 1.5 ) = 13312.5 N.m

Vmax = ( 6.5 * (1.5) + 4 ) = 13750 N

A) determine max bending stress

б = [tex]\frac{MC}{I}[/tex]  =  [tex]\frac{13312.5 ( 0.112)}{1/12(0.1^4-0.084^4)}[/tex]  =  159.07 MPa

B) Determine max transverse shear stress

attached below

   ζ = 10.45 MPa

C) Determine max shear stress in the beam

This occurs at the top of the beam or at the centroidal axis

hence max stress in the beam =  159.07 / 2 = 79.535 MPa  

attached below is the remaining solution

Answer:

[tex]0.845\ \text{N}[/tex]

Explanation:

g = Acceleration due to gravity at sea level = [tex]9.81\ \text{m/s}^2[/tex]

R = Radius of Earth = 6371000 m

h = Altitude of observatory = 4205 m

Change in acceleration due to gravity due to change in altitude is given by

[tex]g_h=g(1+\dfrac{h}{R})^{-2}\\\Rightarrow g_h=9.81\times(1+\dfrac{4205}{6371000})^{-2}\\\Rightarrow g_h=9.797\ \text{m/s}^2[/tex]

Weight at sea level

[tex]W=mg\\\Rightarrow W=65\times 9.81\\\Rightarrow W=637.65\ \text{N}[/tex]

Weight at the given height

[tex]W_h=mg_h\\\Rightarrow W_h=65\times 9.797\\\Rightarrow W_h=636.805\ \text{N}[/tex]

Change in weight [tex]W_h-W=636.805-637.65=-0.845\ \text{N}[/tex]

Her weight reduces by [tex]0.845\ \text{N}[/tex].

Answer:

The answer is A

Explanation:

The correct answer is A

Answer: the size of memory needed for the CD recording is 28.7 MB

Explanation:

so in the case of stereo, the bitrate is;

⇒ 26 × 60 × 44.1 × 10³ × 2

=   137592 × 10³  

for 10 bit

⇒ 137592 × 10³ × 10

= 1375920 × 10³ bits

now divide by 8 (convert to bytes)

⇒ (1375920 × 10³) / 8

= 171,990,000 BYTE

divide by 1000 (convert to kilobytes)

= 171,990,000 / 1000

= 171,990 KILOBYTES

now Given that, the compression ratio is 6      

so  

171,990 / 6

= 28665 KB

we know that. 1 MB = 1000 KB

x MB = 28665 KB

x MB = 28665 / 1000

⇒ 28.665 MB ≈ 28.7 MB

Therefore the size of memory needed for the CD recording is 28.7 MB

Answer:

I think the answer is C. Boiling but I'm not 100% sure.

Answer: observational error

Explanation:

An Error occurs when the measurement is actually done by the Observational approach. Thus, the correct option is D.

The ideal methods of measurement are subdivided into two methods: They are as follows:

The Direct measurement method involves the utilization of instruments such as micrometers, vernier calipers, coordinate measuring machines, etc. In this method, the unknown quantity is directly compared with the standard quantity.

In the Indirect measurement method, the physical parameter of the quantity is measured with the help of the direct method.

Positioning of the required quantity, operator-biased measurement, and the utilization of instruments for estimating the measurement of any unknown value are generally favored in order to eliminate the chances of errors.

Therefore, an Error occurs when the measurement is actually done by the Observational approach. Thus, the correct option is D.

To learn more about Errors in Measurement, refer to the link:

https://brainly.com/question/475573

#SPJ2

Answer:

A rectangular shaped tool that functions as a pulley.

Explanation:

i beleive