As a main sequence star exhausts hydrogen in its core, its surface becomes ___ and its energy output per second (luminosity) becomes ____.
Answer:
b
Explanation:
bc
In a second order lever system the force ratio is 2.5, the load is at the distance of 0.5m from the fulcrum find distance of effort if it losses are negligible
Answer:
1.25 m
Explanation:
From the question given above, the following data were obtained:
Force ratio = 2.5
Distance of load from the fulcrum = 0.5 m
Distance of effort =.?
The distance of the effort from the fulcrum can be obtained as illustrated below:
Force ratio = Distance of effort / Distance of load
2.5 = Distance of effort / 0.5
Cross multiply
Distance of effort = 2.5 × 0.5
Distance of effort = 1.25 m
Therefore, the distance of the effort from the fulcrum is 1.25 m
how to solve for resistors
9514 1404 393
Answer:
A1 = 3A, A2 = 1.5A
Effective resistance = 2Ω
Explanation:
When the switch is closed, the voltage across each resistor is 6V, so the current through it (A2) is ...
A2 = 6V/(4Ω) = 1.5A
There are two parallel paths, each with that current, so the current from the battery is ...
A1 = A2 +A2 = 1.5A +1.5A = 3.0A
Then the effective resistance is ...
Reff = 6V/(3.0A) = 2.0Ω
The solution to the circuit is ...
A1 = 3A, A2 = 1.5A
Effective resistance = 2Ω
At what common temperature will a block of wood and a block of metal both feel neither hot nor cold to the touch? 1. when the temperature of the blocks is higher than the temperature of your hand 2. when the temperature of the blocks is the same as the temperature of your hand 3. when the temperature of the blocks is lower than the temperature of your hand 4. at room temperature 5. at the freezing point
When the temperature of the blocks is the same as the temperature of your hand, you feel neither hot nor cold to the touch. Hence, option ( 3) is correct.
What is temperature?Temperature is a unit used to describe hotness or coldness. It can be stated in terms of any number of arbitrary scales and shows the direction in which heat energy will naturally flow, i.e., from a hotter body to a colder body (one at a lower temperature).
Temperature is not the same as the energy of a thermodynamic system; for instance, an iceberg has a significantly larger total heat energy than a match, despite the fact that a match is burning at a much higher temperature.
If you touch a block that is at higher than or at lower than the temperature of your hand, you feel hot or cold respectively. But, when the temperature of the blocks is the same as the temperature of your hand, you feel neither hot nor cold to the touch.
Learn more about temperature here:
https://brainly.com/question/11464844
#SPJ5
Which diagram shows the most likely effect when a rock is weathered by water flowing over its entire surface
Answer:
the answer to this would be D.
Answer: Its D but it might swap to another letter so keep your eye out bud pass this test good luck
Explanation:
01:28:29
What type of relationship occurs when two variables both increase or decrease together?
O an inverse relationship
O a positive relationship
a direct relationship
O an indirect relationship
Answer:
an inverse relationship
write any two difference between CGS and MKS system of measurement ?
Answer:
MKS stands for Meter, Kilogram and second. In this system of unit mass is given in Kilogram, length in meter and time in second. ... CGS system stands for Centimeter- Gram- Second system. In CGS system, length is measured in centimeters mass is measured in grams and time is in seconds.
what is the value of acceleration due to gravity at the equatorial region of the earth
Answer:
9.78 m/s^2
Explanation:
Acceleration due to gravity at equator is 9.78m/s^2
How long will it take a car to acceleration from 15.2ms to 23.Ms if the car has an average acceleration of 3.2m\s
Answer: 2.43 s
Explanation:
Initial velocity is [tex]u=15.2\ m/s[/tex]
Final velocity [tex]v=23\ m/s[/tex]
Average acceleration is [tex]a_{avg}=3.2\ m/s[/tex]
Average acceleration is change in velocity in the given amount of time
[tex]\therefore a_{avg}=\dfrac{v-u}{t}\\\\\Rightarrow 3.2=\dfrac{23-15.2}{t}\\\\\Rightarrow t=\dfrac{7.8}{3.2}\\\\\Rightarrow t=2.43\ s[/tex]
Thus, 2.43 s is required to acquire that average acceleration with 23 m/s velocity .
Please answer will mark brainleist
[tex]option \: (a) \: is \: correct.[/tex]
Explanation:
Yes, I was wrong. Pressure increases as the area decreases.
As per the Figure A, the truck is so heavy and having a greater mass. So, the area of contact between the tyres and the road increases and decreases it's pressure on the road due to the increase in area.
As per the Figure B, You know the nature of Tomato that it is soft and smooth to touch and also lighter mass when it's compared with the truck. As it having a lighter mass, it can be cut through the sharp knife. The area of contact decreases and pressure increases on the vegetables.
Answer:
Option number B
Explanation:
The pressure is indirectly proportional to the area therefore pressure decreases when the area increases, and pressure increases when the area decreases
A system consists of multiple objects connected by ropes. How many equations need to be written to solve this problem?
A) two for each object
B) one or two for each object
C) one for each object
D) two for the system
Answer:
the correct answer is B
Explanation:
To solve the system they must have the same amount of unknowns as equations,
a) If the system does not have friction, we must write the x-axis equation for each body, therefore we need to write N equations
b) if the system has friction, two equations are needed for each particle
therefore the correct answer is B
A cube of aluminum of mass 4kg is immersed totally in kerosene. It was found that 50g of kerosene was displaced, if the density of the kerosene is 13.5kg/m³, calculate the length and density of the aluminum cube
The length and density of the aluminum cube is 15.46 cm and 1,081.1 kg/m³ respectively
Volume of the aluminumThe volume of the aluminum is equal to the weight of the kerosene displaced.
V = 0.05 kg / 13.5 kg/m³
V = 3.7 x 10⁻³ m³
Density of the aluminumdensity = mass/volume
density = 4 kg / 3.7 x 10⁻³ m³
density = 1,081.1 kg/m³
Length of the aluminumV = L³
L = ∛V
L = ∛(3.7 x 10⁻³)
L = 0.1546 m
L = 15.46 cm
Thus, the length and density of the aluminum cube is 15.46 cm and 1,081.1 kg/m³ respectively.
Learn more about density here: https://brainly.com/question/6838128
#SPJ1
Does direction matter when determining distance?
yes
no
Answer:
no
Explanation:
ans should be correct
Carlos is playing darts. He throws a dart at the bullseye, but it hits the outer ring of the dartboard instead. He aims for the bullseye again and hits it with a second dart. Carlos threw three more darts which landed close to his first shot. What does the second throw indicate about his accuracy and precision? The second throw shows poor accuracy but high precision. The second throw shows accuracy but poor precision. The second throw shows both accuracy and precision. The second throw shows poor accuracy and poor precision.
Answer:
The second throw shows both accuracy and precision.
Explanation:
The second throw shows both accuracy and precision because he knew in which degree and the amount of force that can be applied to the dart so that it hits the center of the bullseye or close to it. Due to knowing of these two things the Carlos is able to hit the dart close to the target at the second time so in this way he got both accuracy and precision at the second turn of throwing darts.
Answer:
B-The second throw shows accuracy but poor precision.
Explanation:
Why are dark matter and dark energy described as dark
Dark matter and dark energy described as dark because of its no interaction with electromagnetic field.
Why are dark matter and dark energy described as dark?
Dark matter is called "dark" because it does not interact with the electromagnetic field. This means that it does not absorb, reflect, or emit electromagnetic radiation and therefore, it is difficult to detect.
So we can conclude that dark matter and dark energy described as dark because of its no interaction with electromagnetic field like dark substances.
Learn more about matter here:https://brainly.com/question/3998772
#SPJ1
Dark matter and dark energy are described as dark because it doesn't seem to interact with the electromagnetic field.
What is the matter?The matter is a material that fills space and has inertia. Modern physics states that matter is made up of several kinds of particles, each of which has a mass and size.
The electron, proton, and neutron are three of the most well-known instances of material particles. Atoms are made up of combinations of these particles.
Dark matter is so-called because it doesn't seem to interact with the electromagnetic field.
This means it doesn't generate electromagnetic radiation like light or absorb electromagnetic radiation as it does. As a result, it is hard to detect.
Hence, dark matter and dark energy are described as dark.
To learn more about the matter refer;
https://brainly.com/question/4513444
#SPJ1
In a cup game if the teams have the same score at the end of the match, 30 minutes of ------- are played.
Answer:
second lag
Explanation:
If in a cup game, a specified time limit is assigned to both teams to score high. If both teams are unable to score or if score of both the teams is equal then there is another second lag played where each team tries to score high. Even if in second lag both teams fail to score higher than other the last third lag is played or else game is declared draw.
A box slides down a 28.0 degree ramp with an acceleration of 1.25 m/s2. Determine the coefficient of kinetic friction between
Answer:
[tex]\mu=0.39[/tex]
Explanation:
From the question we are told that:
Angle [tex]\theta=28[/tex]
Acceleration [tex]a=1.25m/s^2[/tex]
Generally the equation for Frictional force is mathematically given by
[tex]F=\muN[/tex]
Where
[tex]N=mgcos \theta[/tex]
[tex]N=mgcos 28[/tex]
Since
Friction force is acting against move of box
Therefore
[tex]mgsin(28) - 1.25m = \mu mgcos(28)[/tex]
[tex]\mu=\frac{gsin(28) - 1.25}{gcos(28)}[/tex]
[tex]\mu=0.39[/tex]
A 1.25 kg block is attached to a spring with spring constant 17.0 N/m . While the block is sitting at rest, a student hits it with a hammer and almost instantaneously gives it a speed of 49.0 cm/s . What are You may want to review (Pages 400 - 401) . Part A The amplitude of the subsequent oscillations
Answer:
The amplitude of the subsequent oscillations is 13.3 cm
Explanation:
Given;
mass of the block, m = 1.25 kg
spring constant, k = 17 N/m
speed of the block, v = 49 cm/s = 0.49 m/s
To determine the amplitude of the oscillation.
Apply the principle of conservation of energy;
maximum kinetic energy of the stone when hit = maximum potential energy of spring when displaced
[tex]K.E_{max} = U_{max}\\\\\frac{1}{2} mv^2 = \frac{1}{2} kA^2\\\\where;\\\\A \ is \ the \ maximum \ displacement = amplitude \\\\mv^2 = kA^2\\\\A^2 = \frac{mv^2}{k} \\\\A = \sqrt{\frac{mv^2}{k}} \\\\A = \sqrt{\frac{1.25\ \times \ 0.49^2}{17}} \\\\A = 0.133 \ m\\\\A = 13.3 \ cm[/tex]
Therefore, the amplitude of the subsequent oscillations is 13.3 cm
A vehicle starts from rest with a uniform acceleration of 2m/s2.Find the final velocity of the vehicle after covering a distance of 400m
Answer:
40
Explanation:
vi=0
a=2
vf=?
d=400
vf^2=vi^2+2ad
vf^2=0+2×2×400=1600
vf=√1600=40m/s
The atmosphere of Venus is mostly carbon dioxide, and the atmosphere of the Earth has water vapor. Why are these two gases absent in the atmosphere of the satellite around Saturn called Titan
Answer:
if these gases existed in Titan, this n in solid form, by which its absence in the atmosphere is understood.
Explanation:
Each gas and chemical compound has a defined temperature for changes of state, specifically for the change from gaseous to liquid and from liquid to solid state we have
gas gas → liquid liquid → solid
(ºC) (ºC)
H₂0 (Water) 100 0
CO₂ -56.6 (P> = 5.2 bar) <-56.6
The temperature of the Titan satellite is - 180ºC
From the above, if these gases existed in Titan, this n in solid form, by which its absence in the atmosphere is understood.
What is the tangential speed of a point on a wheel of a car if the point is located 0.114 m from the axis of rotation; and the wheel is rotating at 6.53 rev/sec?
Answer:
Tangential speed = R * w where w is the angular speed
For a wheel v = .114 m * 6.53 / sec = .744 m/s
Note that this is the tangential speed - If the wheel were moving at speed V then as viewed from the ground you have
top V + v
bottom V - v
That is the wheel also has speed due to the speed of the axle (axis of rotation)
A train is travelling at 50 m s−1 when the driver applies the brakes and gives the train a constant deceleration of magnitude 0.50 m s−2 for 100 s. Describe what happens to the train. Calculate the distance travelled
Answer:
The strain will come to rest after traveling some distance.
distance traveled = 2500 m
Explanation:
The strain will come to rest after traveling some distance.
Applying,
s = ut+at²/2................... Equation 1
Given: u = initial velocity, a = deceleration, t = time, s = distance
From the question,
Given: u = 50 m/s, t = 100s, a = -0.5 m/s²(deceleration)
Substitute these values into equation 1
s = 50(100)+(-0.5)(100²)/2
s = 5000-2500
s = 2500 m
Hence the distance traveled is 2500 m
3. Thekinetic energy of an object of
mass, m moving with a velocity
of 5 ms-t is 25 J. What will be its
Toinetic energy when its velocity
is doubled? What will be its
Icinetic energy ruhen its velocity
is increased three times?
Answer:
1. 100 J
2. 225 J
Explanation:
We'll begin by calculating the mass of the object. This can be obtained as follow:
Velocity (v) = 5 ms¯¹
Kinetic energy (KE) = 25 J
Mass (m) =?
KE = ½mv²
25 = ½ × m × 5²
25 = ½ × m × 25
25 = 25m / 2
Cross multiply
25m = 25 × 2
25m = 50
Divide both side by 25
m = 50 / 25
m = 2 Kg
1. Determination of the kinetic energy when the velocity is doubled.
Mass (m) = 2 Kg
Velocity (v) = double the initial velocity
= 2 × 5 ms¯¹
= 10 ms¯¹
Kinetic energy (KE) =?
KE = ½mv²
KE = ½ × 2 × 10²
KE = ½ × 2 × 100
KE = 100 J
2. Determination of the kinetic energy when the velocity increased three times.
Mass (m) = 2 Kg
Velocity (v) = three times the initial velocity
= 3 × 5 ms¯¹
= 15 ms¯¹
Kinetic energy (KE) =?
KE = ½mv²
KE = ½ × 2 × 15²
KE = ½ × 2 × 225
KE = 225 J
The categories specified in the DSM: a. change from edition to edition b. are influenced by social trends c. may reflect Western cultural biases d. a, b, and c
Answer:
The correct alternative is Option b (are influenced by social trends).
Explanation:
DSM seems to be a mental sickness seems to be a psychiatric disease. Mental diseases are disorders of healthcare that affect emotions, thought, as defined mostly on the American Psychological Association website.Psychological disorders are socially associated or connected, workplace and familial issues as well as problems.There is no connection between the other three choices. Thus, the answer is right.
Apakah yang berlaku kepada kekuatan medan magnet jika satu lagi sel kering 1.5 v ditambahkan
Answer:
The magnetic field is doubled.
Explanation:
What happens to the strength of the magnetic field if one more 1.5 v dry cell is added?
The magnetic field due to a current carrying conductor is directly proportional to the current flowing in the wire.
If we connect one more battery of 1.5 V so the voltage is doubled and according to the Ohm's law, as the resistance of wire is constant, so the current in the wire is also doubled.
When the current doubles, the magnetic field produced by the wire is also doubled.
The Displacement is 5m. We found that using the
Pythagorean Theorem.
Vector Quantities require both a Displacement and a
Direction.
What direction is this Vector?
South
Northeast
West
Answer:
A vector can be written as:
(R, θ)
Where R is the magnitude, in this case, we know that the magnitude of the displacement is 5m
Then:
R = 5m
and θ defines the direction, it's an angle measured from the positive x-axis.
(In the image, θ would be the angle located at the point A)
Now, if you look at the image, you can see a triangle rectangle.
Where the adjacent cathetus has a length of 4,
the opposite cathetus has a length of 3 units
the hypotenuse has a length of 5 units.
So we can use any trigonometric rule to find the value of θ, like:
sin(θ) = (opposite cathetus)/hypotenuse
Then:
sin(θ) = 3m/5m
Now we can use the inverse sin function, Asin(x), in both sides
Asin( sin(θ)) = θ = Asin( 3/5) = 36.87°
then the vector is:
(5m, 36.87°)
Now, if we define the positive y-axis as the North, and the positive x-axis as the East.
This vector would point at 36.87° North of East.
(or almost Northeast)
help me do the c.....
yup they r equal as mentioned above is equal magnitude and direction! so they r totally equal.
as one vector has 2 things which is used to define it ->
Magnitudedirectionso if both r equal then both vectors r equal vectors
In Boolean Algebra zero represent
1) Zero potential
2) Ground potential
3) low potential
4) Both 1 &2
Answer:
Option 1 & 2
Explanation:
The area of mathematics known as Boolean algebra concerns with operations on logical quantities with binary variables. To express truths, Boolean features are transformed as binary numbers: 1 = true and 0 = false. Boolean algebra concerns with logistical processes, whereas fundamental algebra deals with machine based.
Which of the following is not an example of bias
A. Pro hi FRUCTOSE corn syrup ADVERTISEMENTS paid for by corn farmers
B. anti-smoking articles written by the national health ASSOCIATION
C. anti-by four articles written by a journalist working for it Oil company
D Pro ADHD medicine article written by PHARMACEUTICAL
Answer:
B
Explanation:
The writers are from a trusted source that is considered impartial. The message is backed up by scientific investigation, and the writers have no monetary gain from their message.
Two students with masses of 40kg and 32 kg are sitting 22 m apart. What is the gravitational force of attraction between them?
I get 1.76 x 10^-10 Newton.
That's 0.000 000 000 176 Newton
Which is about 0.000 000 000 635 ounce of force pulling them together.
That's why we never notice it.
