HELPPP ILL GIVE BRAINLIST

Answer:

Initial velocity (u) = 40 m/s

Distance travel in last 5 seconds = 100 m

Explanation:

Given:

Acceleration (a) = 8 m/s²

Final velocity (v) = 0 m/s

Find;

1] Initial velocity before 5 sec

2] Distance travel in last 5 seconds

Computation:

1] Initial velocity before 5 sec

v = u + at

0 = u + (-8)(5)

u - 40 = 0

Initial velocity (u) = 40 m/s

2] Distance travel in last 5 seconds

s = ut + (1/2)(a)(t²)

s = (40)(5) + (1/2)(-8)(5²)

s = 200 - 100

Distance travel in last 5 seconds = 100 m

Answer:

  (D) 4×10⁻³

Explanation:

The difference is ...

  0.2050 -0.2014 = 0.0036 = 3.6×10⁻³

The number 0.205 is expressed to a precision of 1×10⁻³, so the result of the subtraction operation cannot be considered to be more precise. It must be expressed as ...

  4×10⁻³ . . . . matches choice D

_____

Additional comment

This is physics, not math. In the physical sciences, most numbers must be considered to be measurements. (A few are definitions.) Hence, the rules of significant figures and precision apply to the results of arithmetic operations. This problem is a good illustration of what happens when computing small differences of large numbers. We start with 3 significant figures in 0.205, and end up with 1 significant figure in 0.004.

Answer:

1084860 N

Explanation:

Applying,

P = ρgh................ Equation 1

Where P = pressure, ρ = density, h = height, g = acceleration due to gravity.

From the question,

Given:  ρ = 1025 kg/m³, h = 9 m

Constant: g = 9.8 m/s²

Substitute these values into equation 1

P = (1025)(9)(9.8)

P = 90405 N/m²

Also,

P = F/A.............. Equation 2

Where, F = Force, A = Area.

Make F the subject of the equation

F = PA............... Equation 2

Given: A = 12m²

F = 12(90405)

F = 1084860 N

Answer:

A single fixed pulley is used to lift load by changing the direction of the lifting force. Even though a single fixed pulley has no mechanical gain in that, the effort applied is greater than the load, it is preferred in use since you do not have to pull or push the pulley up and down.

Explanation:

The answer itself speaks

Answer:

250 kgm/s

Explanation:

To calculate momentum, simply take the product of the mass and velocity.

Answer:

1. A hiking

2. C

3. B

4. D

5. E

Answer:

I don't agree

Explanation:

Atoms have 3 subatomic particles protons, electrons and neutrons,

Answer:

ANO BA TO?(;-;)

Explanation:

miss the rage??

Answer:

50 N.

Explanation:

From the question given above, the following data were obtained:

Mass (m) = 5 Kg

Coefficient of friction (μ) = 0.36

Normal reaction (N) =?

Next, we shall determine the weight of the body. This can be obtained as follow:

Mass (m) = 5 Kg

Acceleration due to gravity (g) = 10 m/s²

Weight (W) =?

W = mg

W = 5 × 10

W = 50 N

Finally, we shall determine the normal reaction. This can be obtained as follow:

Weight (W) = 50 N

Normal reaction (N) =?

Normal reaction = weight of the body

N = W = 50 N

Thus, the normal reaction acting on the body is 50 N

Answer:

there it is fella atleast i tried

Answer:

Distance = 30 meters

Explanation:

Given the following data;

Speed = 1.5 m/s

Time = 20 seconds

To find the distance travelled;

Speed can be defined as distance covered per unit time. Speed is a scalar quantity and as such it has magnitude but no direction.

Mathematically, speed is given by the formula;

[tex]Speed = \frac{distance}{time}[/tex]

Making distance the subject of formula, we have;

[tex] Distance = speed * time [/tex]

Substituting into the above formula, we have;

[tex] Distance = 1.5 * 20 [/tex]

Distance = 30 meters

Answer:

It's B = Energy ....

i hope its right

Answer:

Please find detailed explanation of second class levers below

Explanation:

Levers are one of the classes of machine that possesses three levels namely: first class, second class and third claas. A second class lever is the level of levers in which the load (L) is in between the pivot (F) and the effort (E).

Examples of second class levers include; wheelbarrow, a bottle opener etc. In the bottle opener for example, the bottle lid (load) is in between the pivot of the opener and the hand opening it (effort).

Answer:

a. Energy = 28800000 Joules

b. Energy = 8 Kwh

c. Cost = $4

Explanation:

Given the following data;

Power = 1000 Watts

Time = 8 hours

Cost = $0.5 per KWh

Conversion:

1 hour = 60 * 60 = 3600 seconds

8 hour = 8 * 3600 = 28800 seconds

a. To find much electrical energy, in joules;

Energy = power * time

Energy = 1000 * 28800

Energy = 28800000 Joules

b. To find how much energy is that in kilowatt hours;

Energy = power * time

Energy = 1000 * 8

Energy = 8000 Watt-hour = 8000/1000 = 8 Kwh (1 Kilowatts is equal to 1000 watts).

c. To calculate the cost of using this heater;

Cost = 8 * 0.5

Cost = $4

Answer:

The dimension is L

Explanation:

Dimension analysis is a method of representing quantities majorly with respect to some fundamental quantities of mass (M), length (L), time (T).

A sphere has a definite volume which relates to its radius by:

V = [tex]\frac{4}{3}[/tex][tex]\pi[/tex][tex]r^{3}[/tex]

In this equation [tex]\pi[/tex] is a dimensionless quantity, and the unit of v is [tex]m^{3}[/tex].

But, metre is a measure of length, thus it has a dimension of L.

So that,

[tex]m^{3}[/tex] ≅ [tex]L^{3}[/tex]

Then,

[tex]L^{3}[/tex] = [tex]r^{3}[/tex]

Find the cube root of both sides to have,

r = L

Therefore, the dimension of the radius of a sphere is L.

Answer:

B. Uranium 238.

Explanation:

It is radioactive and can be used to treat cancer in the form of radiotherapy

Answer:

Jupiter and neptune

Explanation:

Answer:

Infinite

Explanation:

Young's modulus is infinite and bulk modulus is zero.

Answer:

Young's modulus is the ratio of tensile stress ( force of elasticity ) to tensile strain ( extension ).

Explanation:

[tex]E = \frac{stress}{strain} [/tex]

Answer:

Arrange an annual service. Treat your boiler like your car. ...

Keep your boiler clean. ...

Bleed your radiators. ...

Top up the pressure. ...

Use a Powerflush. ...

Insulate your pipes. ...

Turn the heating on. ...

If all else fails…

Explanation:

Answer:

Option C

Explanation:

From the question we are told that:

Mass [tex]m=0.015kg[/tex]

Radius [tex]r=0.5m[/tex]

Time [tex]t=0.70[/tex]

Generally the equation for Tension is mathematically given by

 [tex]T=\frac{4mr}{t^2} \pi[/tex]

 [tex]T=\frac{4*0.015*0.5}{(0.70)^2} (3.142)[/tex]

 [tex]T=0.60N[/tex]

Therefore

[tex]T=0.60 N[/tex], toward the center of the circle

Option C

Answer:

0.60 N, toward the center of the circle

Explanation:

Got it right on the test.

Answer:

valenc e shell

Explanation:

Answer:

t_total = 6.99 s

Explanation:

It asks us how long it takes to hear the sound, for this we must look for the time (t₁) it takes for the sound to reach the microphone, the time it takes for the video signal (t₂) to reach the television and the time (₃) it takes for the TV sound to reach us, so the total delay time is

         t_total = t₁ + t₂ + t₂

we look for t1, it indicates that the distance x = 22m

          v = x / t

           t = x / v

           t₁ = 22/343

           t₁ = 6.41 10-2 s

time t₂

          t₂ = 4500 103/3 108

          t₂ = 1.5 10-5 s

time t₃

          t₃ = 2/343

          t₃ = 5.83 10⁻³

Total time is

         t_total = t₁ + t₂ + t₃

         t_total = 6.41 10⁻² + ​​1.5 10⁻⁵ + 0.583 10⁻²

         t_total = 6.99 s

The question is incomplete. The complete question is  :

The pressure difference, Δp, ac[tex]K_u[/tex]ross a partial blockage in an artery (called a stenosis) is approximated by the equation :

[tex]$\Delta p=K_v\frac{\mu V}{D}+K_u\left(\frac{A_0}{A_1}-1\right)^2 \rho V^2$[/tex]

Where V is the blood velocity, μ the blood viscosity {FT/L2}, ρ the blood density {M/L3}, D the  artery diameter, [tex]A_0[/tex] the area of the unobstructed artery, and A1 the area of the stenosis.  Determine the dimensions of the constants [tex]K_v[/tex] and [tex]K_u[/tex]. Would this equation be valid in any  system of units?

Solution :

From the dimension homogeneity, we require :

[tex]$\Delta p=K_v\frac{\mu V}{D}+K_u\left(\frac{A_0}{A_1}-1\right)^2 \rho V^2$[/tex]

Here, x means dimension of x. i.e.

[tex]$[ML^{-1}T^{-2}]=\frac{[K_v][ML^{-1}T^{-1}][LT^{-1}]}{[L]}+[K_u][1][ML^{-3}][L^2T^{-2}]$[/tex]

                    [tex]$=[K_v][ML^{-1}T^{-2}]+[K_u][ML^{-1}T^{-2}]$[/tex]

So, [tex]$[K_u]=[K_v]=[1 ]=$[/tex] dimensionless

So, [tex]K_u[/tex] and [tex]K_v[/tex]  are dimensionless constants.

This equation will be working in any system of units. The constants [tex]K_u[/tex] and [tex]K_v[/tex] will be different for different system of units.

Answer:

The Most Famous Astronomers of All Time. Karl Tate, SPACE.com. ...

Claudius Ptolemy. Bartolomeu Velho, Public Domain. ...

Nicolaus Copernicus. Public Domain. ...

Johannes Kepler. NASA Goddard Space Flight Center Sun-Earth Day. ...

Galileo Galilei. NASA

Answer:

2

Explanation:

in reflection the incident ray and reflected rays are equal an angle

Answer:

All of them are false

Explanation:

4. electrons flow from earth to the object

5. electrons move freely

6. protons can't move

Answer:

They all false

Answer:

youd use a thermometer. this can be used to measure the temperature of a solid such as food, a LIQUID such as water, or a gas such as air.

Explanation:

Answer:

The ratio of forces is 22 : 3.

Explanation:

Case I:

initial velocity, u = 35 mph

final velocity, v = 0

time, t = 15 ms

Case II:

initial velocity, u = 35 mph

final velocity, v = 0

time, t' = 110 ms

let the mass is m.

According to the Newton's second law, the force is given by the rate of change of momentum.

So

[tex]F =\frac{m(v-u)}{t}\\\\F'= \frac{m(v-u)}{t'}\\\\So, \frac{F}{F'} =\frac{t'}{t}\\\\\frac{F}{F'}=\frac{110}{15}=22:3[/tex]