Half-cells were made from a nickel rod dipping in nickel sulfate solution and a copper rod dipping in copper sulfate solution. The cells were combined to construct a voltaic electrochemical cell. Sketch the cell and label anode and cathode with charges, electrode material and electrolyte solutions, half-reactions and overall reaction, give direction of electron flow and movement of ions.
Answers
Answer:
Check the Attachment.
Half-reactions:
Anode: (OXIDATION) Ni --> Ni2+ + 2e-
Cathode: (REDUCTION) Cu2+ +2e- --> Cu
Overall reaction: Ni + Cu2+ --> Ni2+ + Cu
Explanation:
Overall, reaction is basically Anode + Cathode, where electrons on both sides cancel out (if not, you need to multiply the equation in a way you can cancel them out).
Hope this helps.
Related Questions
Using the data: C2H4(g), = +51.9 kJ mol-1, S° = 219.8 J mol-1 K-1 CO2(g), = ‑394 kJ mol-1, S° = 213.6 J mol-1 K-1 H2O(l), = ‑286.0 kJ mol-1, S° = 69.96 J mol-1 K-1 O2(g), = 0.00 kJ mol-1, S° = 205 J mol-1 K-1 calculate the maximum amount of work that can be obtained, at 25.0 °C, from the process: C2H4(g) + 3 O2(g) → 2 CO2(g) + 2 H2O(l)
Answers
Answer:
The correct answer is 1332 KJ.
Explanation:
Based on the given information,
ΔH°f of C2H4 is 51.9 KJ/mol, ΔH°O2 is 0.0 KJ/mol, ΔH°f of CO2 is -394 KJ/mol, and ΔH°f of H2O is -286 KJ/mol.
Now the balanced equation is:
C2H4 (g) + 3O2 (g) ⇔ 2CO2 (g) + 2H2O (l)
ΔH°rxn = 2 × ΔH°f CO2 + 2 × ΔH°fH2O - 1 × ΔH°fC2H4 - 3×ΔH°fO2
ΔH°rxn = 2 (-394) + 2(-286) - 1(51.9) - 3(0)
ΔH°rxn = -1411.9 KJ
Now, the given ΔS°f of C2H4 is 219.8 J/mol.K, ΔS°f of O2 is 205 J/mol.K, ΔS°f of CO2 is 213.6 J/mol.K, and ΔS°f of H2O is 69.96 J/mol.K.
Now based on the balanced chemical reaction,
ΔS°rxn = 2 × ΔS°fCO2 + 2 ΔS°fH2O - 1 × ΔS°f C2H4 - 3 ΔS°fO2
ΔS°rxn = 2 (213.6) + 2(69.96) - 1(219.8) -3(205)
ΔS°rxn = -267.68 J/K or -0.26768 KJ/K
T = 25 °C or 298 K
Now putting the values of ΔH, ΔS and T in the equation ΔG = ΔH-TΔS, we get
ΔG = -1411.9 - 298.0 × (-0.2677)
ΔG = -1332 KJ.
Thus, the maximum work, which can obtained is 1332 kJ.
A sample is found to contain 1.29×10-11 g of salt. Express this quantity in picograms
Answers
Answer:12.9e-12g or in short 12.9pg
Explanation:as p=1e-12
Write the equation for the reaction described: A solid metal oxide, , and hydrogen are the products of the reaction between metal and steam. (Use the lowest possible coefficients. Use the pull-down boxes to specify states such as (aq) or (s). If a box is not needed, leave it blank.)
Answers
Answer:
Pb + 2H2O --> PbO2 + 2H2
Explanation:
Products:
Solid metal; PbO2
Hydrogen; H
Reactants:
Metal; Pb
Steam; H2O
Reactants --> Products
Pb + H2O --> PbO2 + H2
Upon balancing we have;
Pb + 2H2O --> PbO2 + 2H2
An aqueous solution of potassium bromide, KBr, contains 4.34 grams of potassium bromide and 17.4 grams of water. The percentage by mass of potassium bromide in the solution is 20 %.
Answers
Answer:
True
Explanation:
The percentage by mass of a substance in a solution can be calculated by dividing the mass of the substance dissolved in the solution by the total mass of the solution. This can be expressed mathematically as:
Percentage by mass = mass of substance in solution/mass of solution x 100
In this case;
mass of KBr = 4.34 grams
mass of water = 17.4 grams
mass of solution = mass of KBr + mass of water = 4.34 + 17.4 = 21.74
Percentage by mass of KBr = 4.34/21.74 x 100
= 19.96 %
19.96 is approximately 20%.
Hence, the statement is true.
g What is the molarity of hydrochloric acid if 40.95 mL of HCl is required to neutralize 0.550 g of sodium oxalate, Na2C2O4
Answers
Answer:
0.0002 M
Explanation:
The molarity of the HCl required would be 0.0002 M.
First, let us consider the balanced equation of the reaction:
[tex]Na_2C_2O_4 + 2HCl = 2NaCl + H_2 + 2CO_2[/tex]
Stoichiometrically, 1 mole of [tex]Na_2C_2O_4[/tex] reacts with 2 moles of [tex]HCl[/tex] for a complete neutralization reaction.
Recall that: mole = [tex]\frac{mass}{molar mass}[/tex]
Mole of 0.550 g sodium oxalate = 0.550/134 = 0.0041 mole
If 1 mole [tex]Na_2C_2O_4[/tex] requires 2 moles HCl, then 0.0041 mole will require:
0.0041 x 2 = 0.0082 mole HCl
Volume of the HCl = 40.95 L
Molarity = mole/volume
Hence, molarity of the HCl = 0.0082/40.95 = 0.0002 M
The K sp for silver(I) phosphate is 1.8 × 10 –18. Determine the silver ion concentration in a saturated solution of silver(I) phosphate.
Answers
Answer:
[tex][Ag^+]=4.82x10^{-5}M[/tex]
Explanation:
Hello,
In this case, the dissociation reaction for silver phosphate is:
[tex]Ag_3PO_4(s)\rightleftharpoons 3Ag^+(aq)+PO_4^{3-}(aq)[/tex]
Therefore, the equilibrium expression is:
[tex]Ksp=[Ag^+]^3[PO_4^{3-}][/tex]
And in terms of the reaction extent [tex]x[/tex] is:
[tex]Ksp=1.8x10^{-18}=(3x)^3(x)[/tex]
Thus, [tex]x[/tex] turns out:
[tex]1.8x10^{-18}=27x^4\\\\x=\sqrt[4]{\frac{1.8x10^{-18}}{27} } \\\\x=1.61x10^{-5}M[/tex]
In such a way, the concentration of the silver ion is:
[tex][Ag^+]=3x=3*1.61x10^{-5}M=4.82x10^{-5}M[/tex]
Best regards.
2. In what part of an atom can protons be found?
a. Inside the electrons
b. Inside the neutrons
C. Inside the atomic nucleus
d. Inside the electron shells
Answers
Answer:
c
Explanation:
it's found inside the atomic nucleus
Determine whether the following statement about reaction rates is true or false. If the statement is false, select the reason why?
Increasing the temperature of a reaction system decreases the activation energy of the reaction.
Answers
Answer:
False
Explanation:
Reaction rates is a field under chemical kinetics that deals with the measure of speed of a chemical reaction. It is the change in the concentration of a reactant or product per unit time.
Activation Energy is a theory been put forward to explain why different chemical reactions proceed at different rates.
Activation Energy theory postulates that for a reactant to transform into a product , the colliding particles or molecules of the reactant must possess a certain amount of energy so as to overcome the reaction barrier.
An important factor which may influence the attainment of activation energy by colliding particles of reactants is the temperature at which the reaction is carried out. The higher the temperature, the greater is the fraction of the reactant particles which possess the activation energy and thus the faster the reaction becomes. SO , in essence increasing the temperature of a reaction system do not decreases the activation energy of the reaction but rather also increases the activation energy of the reaction.
What would be the voltage (Ecell) of a voltaic cell comprised of Cd(s)/Cd2+(aq) and Zr(s)/Zr4+(aq) if the concentrations of the ions in solution were [Cd2+] = 0.5 M and [Zr4+] = 0.5 M at 298K?
Answers
Answer:
1.05 V
Explanation:
Since;
E°cell= E°cathode- E°anode
E°cathode= -0.40 V
E°anode= -1.45 V
E°cell= -0.40-(-1.45) = 1.05 V
Equation of the process;
2Zr(s) + 4Cd^2+(aq) ---->2Zr^4+(aq) + 4Cd(s)
n= 8 electrons transferred
From Nernst's equation;
Ecell = E°cell - 0.0592/n log Q
Ecell= E°cell - 0.0592/8 log [0.5]/[0.5]
Since log 1=0
Ecell= E°cell= 1.05 V
A. Rank the following substances in order of decreasing standard molar entropy (S∘).
Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
Br(g)
Cl2(g)
I2(g)
F2(g)
B. Rank the following substances in order of decreasing standard molar entropy (S∘).
Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
H2S(g)
H2O(g)
H2O2(g)
C. Rank the following substances in order of decreasing standard molar entropy (S∘).
Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
C(s, amorphous)
C(s, diamond)
C(s, graphite)
Answers
Answer:
A. Rank the following substances in order of decreasing standard molar entropy (S∘).
Rank the gases from largest to smallest standard molar entropy
I2(g)>Br2(g)>Cl2(g)>F2(g)
B. Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
H2O2(g)>H2S(g) >H2O(g)
C. Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
C(s, amorphous) >C(s, graphite)>C(s, diamond)
Explanation:
Hello,
In this case, we can apply the following principles to explain the order:
- The greater the molar mass, the larger the standard molar entropy.
- The greater the molar mass and the structural complexity, the larger the standard molar entropy.
- The greater the structural complexity, the larger the standard molar entropy.
A. Rank the following substances in order of decreasing standard molar entropy (S∘).
Rank the gases from largest to smallest standard molar entropy
I2(g)>Br2(g)>Cl2(g)>F2(g)
This is due to the fact that the greater the molar mass, the larger the standard molar entropy.
B. Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
H2O2(g)>H2S(g) >H2O(g)
This is due to the fact that the greater the molar mass and the structural complexity, the larger the standard molar entropy as the hydrogen peroxide has four bonds and weights 34 g/mol as well as hydrogen sulfide that has two bonds only.
C. Rank the gases from largest to smallest standard molar entropy. To rank items as equivalent, overlap them.
C(s, amorphous) >C(s, graphite)>C(s, diamond)
Since the molecular complexity is greater in the amorphous carbon (messy arrangement), mid in the graphite and lower in the diamond (well organized).
Regards.
1.) A sample of neon gas at a pressure of 0.646 atm and a temperature of 242 °C, occupies a volume of 515 mL. If the gas is cooled at constant pressure until its volume is 407 mL, the temperature of the gas sample will be ________°C.
2.) A sample of argon gas at a pressure of 0.633 atm and a temperature of 261 °C, occupies a volume of 694 mL. If the gas is heated at constant pressure until its volume is 796 mL, the temperature of the gas sample will be___________°C.
3.) 0.962 mol sample of carbon dioxide gas at a temperature of 20.0 °C is found to occupy a volume of 21.5 liters. The pressure of this gas sample ismm ____________ Hg.
Answers
Answer:1 )T2=134°C 2) T2=339.48°C. 3)
P=817.59 mmHg.
Explanation:
1.Given ;
pressure, P1 of neon gas = 0.646 atm
temperature, T1 =242oC + 273=515oC
Volume, V1 =515ml
Volume V2= 407ml
temperature , T 2= ?
Solution;
And at constant pressure, the volume cools at V2=407 mL at T2=?
From ideal gas equation, PV=nRT
V/T=constant
therefore
V1/V2=T1/T2 = T2=(V2 xT1)/V1
T2=(407 mL x 515 K)/515 mL= 407K.
T2= 407K -273= 134°C. recall 0°C=273 K)
2..Given ;
pressure, P1 of neon gas = 0.633 atm
temperature, T1 =261oC + 273=534oC
Volume, V1 =694ml
Volume V2= 796ml
temperature , T 2= ?
Solution;
And at constant pressure, the volume expands at V2=796mL at T2=?
From ideal gas equation, PV=nRT
V/T=constant
therefore
V1/V2=T1/T2 = T2=(V2 xT1)/V1
T2=(796 mL x 534 K)/694mL= 612.48K.
T2= 612.48K -273= 339.48°C. recall 0°C=273 K
3
Given;
moles of CO2= n=0.962 mol,
temperature T=20°C=20+273 K =293 K,
volume V=21.5 L,
gas constant R at L·mmHg/mol·K= 62.3637 L mmHg mol^-1 K^-1
Using ideal gas equation PV=nRT
P=nRT/V
P=(0.962 mol)x(62.3637mmHg mol^-1 K^-1)x(293 K)/(21.5L)
P=817.59 mmHg.
What is the energy of a photon of electromagnetic radiation with a wavelength of 963.5 nm? (c = 3.00 × 108 m/s, h = 6.63 × 10–34 J · s
Answers
Answer:
[tex]E=2.06\times 10^{-19}\ J[/tex]
Explanation:
Given that,
The wavelength of electromagnetic radiation is 963.5 nm.
We need to find the energy of a photon with this wavelength.
The formula used to find the energy of a photon is given by :
[tex]E=\dfrac{hc}{\lambda}\\\\E=\dfrac{6.63\times 10^{-34}\times 3\times 10^8}{963.5\times 10^{-9}}\\\\E=2.06\times 10^{-19}\ J[/tex]
So, the energy of a photon is [tex]2.06\times 10^{-19}\ J[/tex].
The heat of vaporization of water is 40.66 kJ/mol. How much heat is absorbed when 3.11 g of water boils at atmospheric pressure?
Answers
Answer:
The amount of heat that is absorbed when 3.11 g of water boils at atmospheric pressure is 7.026 kJ.
Explanation:
A molar heat of vaporization of 40.66 kJ / mol means that 40.66 kJ of heat needs to be supplied to boil 1 mol of water at its normal boiling point.
To know the amount of heat that is absorbed when 3.11 g of water boils at atmospheric pressure, the number of moles represented by 3.11 g of water is necessary. Being:
H: 1 g/moleO: 16 g/molethe molar mass of water is:
H₂O= 2* 1 g/mole + 16 g/mole= 18 g/mole
So: if 18 grams of water are contained in 1 mole, 3.11 grams of water in how many moles are present?
[tex]moles of water=\frac{3.11 grams*1 mole}{18 gramos}[/tex]
moles of water= 0.1728
Finally, the following rule of three can be applied: if to boil 1 mole of water at its boiling point it is necessary to supply 40.66 kJ of heat, to boil 0.1728 moles of water, how much heat is necessary to supply?
[tex]heat=\frac{0.1728 moles*40.66 kJ}{1 mole}[/tex]
heat= 7.026 kJ
The amount of heat that is absorbed when 3.11 g of water boils at atmospheric pressure is 7.026 kJ.
By heating a 93% pure kclo3 sample, what percentage of its mass is reduced?
2KCLO3---->2KCL+3O2
Answers
Explanation:
free your mind drink water and go outside take fresh air you will get answers
Pentanone was treated with excess sodium cyanide in HCl (aq) followed by hydrogen gas has over Pd. This produced:________
A. 2-amino-1-hexanol
B. 1-amino-2-methylpentan-2-ol
C. 1-cyano-1-pentanol
D. 2-aminomethylpentan-1-ol
Answers
Answer:
B. 1-amino-2-methylpentan-2-ol
Explanation:
In this case, the first step, we have the attack of the nucleophile cyanide ([tex] CN^-[/tex] produced by sodium cyanide to the carbon on the carbonyl group (C=O) producing a negative charge in the oxygen.
Then HCl protonates the molecule to produce a cyanohydrin. This cyanohydrin can be reduced by the action of hydrogen gas ([tex]H_2[/tex]) in the presence of a catalyst ([tex]Pd[/tex]), producing an amino group. With this in mind, the final molecule is: 1-amino-2-methylpentan-2-ol.
See figure 1 to further explanations
I hope it helps!
A small amount of solid calcium hydroxide is shaken vigorously in a test tube almost full of water until no further change occurs and most of the solid settles out. The resulting solution is:______.
Answers
Answer:
Lime water, [tex]Ca(OH)_{2}_({aq} )[/tex] is formed.
Explanation:
Lime-water is a clear and colourless dilute solution of aqueous calcium hydroxide salt.
Small amounts of calcium hydroxide salt, [tex]Ca(OH)_{2}_(s)[/tex] is sparsely soluble at room temperature when dispersed vigorously. if in excess, a white suspension called 'milk of lime'is formed.
I hope this explanation is helpful.
A solution containing a unknown ionic compound, vigorously bubbles when hydrochloric acid (HCl) is added to the solution. This might indicate that the solution contains which anion?
Answers
Answer:
CO3^2-
Explanation:
In qualitative analysis, we try to use chemical reactions to determine the composition of an unknown substance. The addition of certain reagents to the unknown solution gives certain results that show the presence or absence of certain species from the unknown sample.
When dilute HCl is added to an unknown sample and effervescence is observed, then the unknown sample must contain CO3^2- or HCO3^-. The presence of these species is confirmed if the gas evolved is passed through limewater and the gas turns limewater milky.
Atoms are indivisible spheres. 1.plum pudding model 2.Dalton model 3.Bohr model
Answers
Answer: 2. Dalton Model
Explanation:
John Dalton proposed that atoms are indivisible spheres. Although his model of an atom was not entirely new to the scientific world since the ancient Greeks has made a similar statement in the past ( all matter are made up of small indivisible particle called atom).
As of when Dalton proposed his model of an atom, electrons and nucleus where yet to be discovered.
A balloon has an initial volume of 2.954 L containing 5.50 moles of helium. More helium is added so that the balloon expands to 4.325 L. How much helium (moles) has been added if the temperature and pressure stay constant during this process.
Answers
Answer:
8.05 moles
Explanation:
5.50 / 2.954 = x / 4.325
x = 8.05
According to ideal gas equation, if the temperature and pressure stay constant during the process 0.520 moles have been added so that the balloon expands to 4.325 L.
What is ideal gas equation?The ideal gas equation is a equation which is applicable in a hypothetical state of an ideal gas.It is a combination of Boyle's law, Charle's law,Avogadro's law and Gay-Lussac's law . It is given as, PV=nRT where R= gas constant whose value is 8.314.The law has several limitations.The law was proposed by Benoit Paul Emile Clapeyron in 1834.
In the given example if pressure and temperature are constant then V=nR substituting V=4.325 l and R=8.314 so n=V/R=4.325/8.314=0.520 moles.
Thus, 0.520 moles of helium are added if the temperature and pressure stay constant during this process.
Learn more about ideal gas equation,here:
https://brainly.com/question/28837405
#SPJ2
2) What is the concentration (M) of CH3OH in a solution prepared by dissolving 11.7 g of CH3OH in sufficient water to give exactly 230 mL of solution?
Answers
To determine the moles of CH3OH, divide the weight in grams of CH3OH by the molecular weight
11.7g / 32g/mol = 0.366 mol CH3OH
0.366 mol CH3OH / .230 L = your molarity
Calculate the energy required to heat of 1.50 kg silver from -7.8 C to 15.0 C . Assume the specific heat capacity of silver under these conditions is .0235 J*g^-1*K^-1 . Be sure your answer has the correct number of significant digits.
Answers
Answer:
804 J
Explanation:
Step 1: Given data
Mass of silver (m): 1.50 kgInitial temperature: -7.8 °CFinal temperature: 15.0 °CSpecific heat capacity of silver (c): 0.0235J·g⁻¹K⁻¹Step 2: Calculate the energy required (Q)
We will use the following expression.
Q = c × m × ΔT
Q = 0.0235J·g⁻¹K⁻¹ × (1.50 × 10³g) × [15.0°C-(-7.8°C)]
Q = 804 J
Why can gasses change volume?
A. The forces holding the gas particles together are
stronger than gravity.
B. The gas particles have no mass, so they can change volume.
C. Gravity has no effect on gas particles, so they can float away.
O D. There are no forces holding the gas particles together.
Answers
Answer:
There are no forces holding the gas particles together.
Explanation:
A 50.0 L cylinder of oxygen gas is stored at 150. atm. What volume would the oxygen gas occupy if the cylinder were opened into a hot air balloon (completely deflated) until the final pressure is 735 torr
Answers
Answer:
THE VOLUME OF THE OXYGEN GAS AFTER DEFLATION TILL A PRESSURE OF 735 TORR IS ATTAINED IS 7836.99 L
Explanation:
Using Boyle's law,
P1V1 = P2V2
P1 = 150 atm
V1 = 50 L
P2 = 735 Torr
V2 = unknown
We must first convert the pressures into the same SI unit for easy calculation
1torr = 1/760 atm
So converting 735 torr to atm; we have:
1 torr = 1/ 760 atm
735 torr = 735 * 1 / 760 atm
= 0.967 atm
In other words, P2 = 0.957 atm
So rearranging the formula by making V2 the subject of the equation, we have:
V2 = P1 V1 / P2
V2 = 150 * 50 / 0.957
V2 = 7836.99 L
The volume of the oxygen cylinder after deflation to a final pressure of 735 torr or 0.967 atm pressure is 7836.99 L.
A runner can cover 2.0 miles in 31 minutes, how long would it take for this runner to cover 6.0 Km. Hint (1 mile= 1.609 Km)
Answers
The answer to this question is approximately equal to 57.8
What volume (in mL) needs to be added to 69.6 mL of 0.0887 M MgF2 solution to make a 0.0224 M MgF2 solution
Answers
Answer:
The correct answer is 206 ml.
Explanation:
Based on the given information, the molarity or M₁ of MgF₂ solution is 0.0887 M, the molarity or M₂ of the final solution given is 0.0224 M. The initial volume of V₁ of the solution is 69.6 ml, for finding the final volume of V₂ of the solution, the formula to be used is,
M₁V₁ = M₂V₂
Now putting the values in the formula we get,
0.0887 × 69.6 = 0.0224 M × V₂
V₂ = 0.0887 × 69.6 / 0.0224
V₂ = 275.6 ml
Therefore, the volume in ml added to the initial volume of 69.6 ml to make the molarity of the solution 0.0224 will be,
= 275.6 ml - 69.6 ml = 206 ml
A student ran the following reaction in the laboratory at 242 K: 2NOBr(g) 2NO(g) Br2(g) When she introduced 0.143 moles of NOBr(g) into a 1.00 liter container, she found the equilibrium concentration of NOBr(g) to be 0.108 M. Calculate the equilibrium constant, Kc, she obtained for this reaction. Kc
Answers
Answer:
1.84 × 10⁻³
Explanation:
Step 1: Write the balanced equation
2 NOBr(g) ⇄ 2 NO(g) + Br₂(g)
Step 2: Calculate the initial concentration of NOBr
0.143 moles of NOBr(g) are introduced into a 1.00 liter container. The molarity is:
M = 0.143 mol / 1.00 L = 0.143 M
Step 3: Make an ICE chart
2 NOBr(g) ⇄ 2 NO(g) + Br₂(g)
I 0.143 0 0
C -2x +2x +x
E 0.143-2x 2x x
Step 4: Find the value of x
The equilibrium concentration of NOBr(g) was 0.108 M. Then,
0.143-2x = 0.108
x = 0.0175
Step 5: Calculate the concentrations at equilibrium
[NOBr] = 0.108 M
[NO] = 2x = 0.0350 M
[Br₂] = x = 0.0175 M
Step 6: Calculate the equilibrium constant (Kc)
Kc = [0.0350]² × [0.0175] / [0.108]²
Kc = 1.84 × 10⁻³
Describe the similarities between H3O and NH3. Compare/contrast their shapes and polarities within the context of your answer. These molecules are called isoelectronic. Why
Answers
Answer:
Explanation:
[tex]H_3O^+[/tex] also known as hydronium ion is formed as a result of the reaction between an hydrogen proton and a water molecules.
i.e [tex]\mathtt{H^+ + H_2O \to H_3O^+}[/tex]
(molecular geometry for the hydronium ion shows that the lewis structure of hydronium ion possess a three hydrogen ion bonded to a central atom known as oxygen. The oxygen possess a lone pair with a positive ion. So we have three hydrogen atoms and a lone pair attached to the oxygen. We can now say that there are four groups as the steric number in which one of them is a lone pair. This give rise to the trigonal pyramidal shape of the [tex]H_3O^+[/tex] (hydronium ion) with a bond angle of about 109,5°
Similarly, [tex]NH_3[/tex] on the other hand also known as ammonia has a shape that can be also determined by the Lewis structure.
IN ammonia, there are three hydrogen and a lone pairs of electron spreading out as far away from each other from the centre nitrogen. In essence, the valence shell electron pair around hydrogens tend to repel each other. Hence, giving it a trigonal pyramidal shape.
From above the similarities between H3O and NH3 is in their molecular geometry in which both H3O and NH3 have the same shape.
These molecules are called isoelectronic. Why?
Isoelectronic molecules are molecules having the same number of electrons and same electronic configuration structure. As a result H3O and NH3 possess the same number of electrons in the same orbitals and they also posses the same structure.
When balancing redox reactions under basic conditions in aqueous solution, the first step is to:________.
a. balance oxygen
b. balance hydrogen
c. balance the reaction as though under acidic conditions
d. none of the above
Answers
Answer:
When balancing redox reactions under basic conditions in aqueous solution, the first step is to balance oxygen.
Explanation:
Oxidation-reduction reactions or redox reactions are those in which an electron transfer occurs between the reagents. An electron transfer implies that there is a change in the number of oxidation between the reagents and the products.
The gain of electrons is called reduction and the loss of electrons oxidation. That is to say, there is oxidation whenever an atom or group of atoms loses electrons (or increases its positive charges) and in the reduction an atom or group of atoms gains electrons, increasing its negative charges or decreasing the positive ones.
The oxidation and reduction half-reactions, in a basic medium, adjust the oxygens and hydrogens as follows:
In the member of the half-reaction that presents excess oxygen, you add as many water molecules as there are too many oxygen. Then, in the opposite member, the necessary hydroxyl ions are added to fully adjust the half-reaction. Normally, twice as many hydroxyl ions, OH-, are required as water molecules have previously been added.
In short, you first adjust the oxygens with OH-, then you adjust the H with H₂O, and finally you adjust the charge with e-
So, when balancing redox reactions under basic conditions in aqueous solution, the first step is to balance oxygen.
Answer:
c. balance the reaction as though under acidic conditions
Explanation:
When balancing redox reactions under basic conditions, a good technique is to first balance the reaction as though under acidic conditions. We then adjust the result to reflect the basic conditions.
A 25.00 mL sample of unknown concentration of HNO3 solution requires 22.62 mL of 0.02000 M NaOH to reach the equivalence point. What is the concentration of the unknown HNO3 solution
Answers
Answer:The concentration of the unknown HNO3 solution = 0.01809 M
Explanation:
For the acid-base reaction, HNO3 + NaOH-----> NaN03 + H20
we have that
C1 V1 = C2 V2
Where ,
C1 = concentration of HNO3=?
V1 = volume of HNO3 = 25.00 mL,
V2 = volume of NaOH = 22.62 mL,
C2 = concentration of NaOH = 0.02000 M
Therefore ,
25.00 mL x C1 = 22.62 mL x 0.02000 M
= (22.62 mL / 25.00 mL) x 0.02000 M = 0.01809 M
The concentration of the unknown HNO3 solution = 0.01809 M
How has the work of chemists affected the environment over the years?
Answers
Answer:
Chemistry is one of the causes for global warming, and in some cases it can even cause certain illnesses.
Answer:
Chemists have both hurt the environment and helped the environment by their actions.
Explanation:
<3
