Give reason Pascal is a derived unit​

Answers

Answer 1

Answer:

Pascal is a derived unit because it cannot be expressed in any physics terms, but it is an expression of fundamental quantities.

Explanation:

[tex]{ \sf{Pasacal \: ( Pa) = \frac{newtons}{metres {}^{2} } }} \\ \\ { \sf{Pasacal \: (Pa) = \frac{kg \times {ms}^{ - 2} }{ {m}^{2} } }}[/tex]


Related Questions

Two astronomy students travel to South Dakota. One stands on Earth’s surface and enjoys some sunshine. At the same time, the other descends into a gold mine where neutrinos are detected, arriving in time to detect the creation of a new radioactive argon nucleus. Although the photon at the surface and the neutrinos in the mine arrive at the same time, they have had very different histories. Describe the differences.

Answers

Answer:

The photon takes millions of years to reach the Surface of the sun while the Neutrinos travelling at the speed of light reaches the surface of the sun in approximately 2 seconds

The Photon is million year old while the neutrino is just some minutes old as observed by the student .

Explanation:

Although The Photon ( sunshine from the sun's surface ) heating up the student standing on the Earth's surface and the neutrinos discovered by the other student inside the gold mine are both formed in the Sun's core.

The difference between both are

The photon takes millions of years to reach the Surface of the sun while the Neutrinos travelling at the speed of light reaches the surface of the sun in approximately 2 seconds

The Photon is million year old while the neutrino is just some minutes old as observed by the student .

A stone is thrown vertically upwards with an initial velocity of 20m/sec. Find the maximum height ot reaches and the time taken by it to reach the height. (g=10m/s2)

plz short numerical ASAP​

Answers

Answer:

The height reached is 20m, The time taken to reach 20m is 2 seconds

Explanation:

Observing the equations of motion we can see that the following equation will be most helpful for this question.

[tex]v^{2} = u^{2} + 2as[/tex]

We are given initial velocity, u

We know that the stone will stop at its maximum height, so final velocity, v

Acceleration, a

And we are looking for the displacement (height reached), s

Substitute the values we are given into the equation

[tex]0^{2} = 20^{2} + 2(10)s[/tex]

Rearrange for s

[tex]0^{2} -20^{2} =20s[/tex]

[tex]-400=20s[/tex]

[tex]\frac{-400}{20} =s[/tex]

s = -20 (The negative is just showing direction, it can be ignored for now)

The height reached is 20m

Use a different equation to find the time taken

[tex]s = vt - \frac{1}{2} at^{2}[/tex]

Substitute in the values we have

[tex]-20=(0)t - \frac{1}{2} (10)t^{2}[/tex]

Rearrange for t

[tex]-20 =0 -5 t^{2}[/tex]

[tex]\frac{-20}{-5} =t^{2}[/tex]

[tex]4 = t^{2}[/tex]

t = 2s

The time taken to reach 20m is 2 seconds

Cuánto demorará un cuerpo en alcanzar su máxima altura, sabiendo que fue lanzado, verticalmente hacia arriba, con una velocidad cuyo valor fue de 90 m/s?

Answers

Answer:

The maximum height reached is 413.27 m.

Explanation:

How long will it take for a body to reach its maximum height, knowing that it was thrown, vertically upwards, with a velocity whose value was 90 m / s?

initial velocity , u = 90 m/s

gravity, g = 9.8 m/s^2

Let the maximum height is h.

At maximum height the velocity v = 0

Use third equation of motion

[tex]v^2 = u^2 - 2 gh\\\\0 = 90\times 90 - 2 \times 9.8 \times h\\\\h = 413.27 m[/tex]

You are trying to hold your 550 g physics books with your hand against a vertical wall. Using a force sensor you know that the force you are applying is 10.0 N. Below the book on the floor you have placed a motion sensor. The position time graph for the book is given. Find the coefficient of kinetic friction.

Answers

The book's position is changing linearly with time, so its velocity is constant. This means that the net force acting on the book in the direction parallel to the surface is

F = 10.0 N - n = 0

where n is the magnitude of the normal force on the book due to the wall, and the net force perpedicular to the surface is

F = f - (0.550 kg) g = 0

where f is the mag. of kinetic friction, and f = µn where µ is the coefficient of kinetic friction.

Then

n = 10.0 N

• f = (0.550 kg) g = 5.39 N

• 5.39 N = µ (10.0 N)

==>   µ = 0.539

Answer:

Above answer

Explanation:

The book's position is changing linearly with time, so its velocity is constant. This means that the net force acting on the book in the direction parallel to the surface is

∑ F = 10.0 N - n = 0

where n is the magnitude of the normal force on the book due to the wall, and the net force perpedicular to the surface is

∑ F = f - (0.550 kg) g = 0

where f is the mag. of kinetic friction, and f = µn where µ is the coefficient of kinetic friction.

Then

• n = 10.0 N

• f = (0.550 kg) g = 5.39 N

• 5.39 N = µ (10.0 N)

==>   µ = 0.539

Which symbol and unit of measurement are used for electric current?
symbol. A, unit: 1
symbol: C, unit: A
symbol l; unit C
symbol: 1; unitA

Answers

Answer: Symbol is I and unit A

Explanation: A represents Amperes

HOPE THIS HELPS!!!!!!!!

A 25.0 kg probe fell freely with acceleration of 2.00 m/s^2 just before it landed on a distant planet. What is the weight of the space probe on that planet

Answers

Answer:

The weight of the probe is 50 Newtons

Explanation:

Newtons second law states that F = ma

Given the mass of 25kg, and the acceleration of 2m/s^2, we can substitute both values into the equation to find the weight force.

[tex]F = ma[/tex]

[tex]F = 25 * 2[/tex]

[tex]F = 50N[/tex]

The weight of the probe is 50 Newtons

HELP ASAP
A. 1.09 A
B. 1.20 A
C.0.910 A
D. 0.830 A

Answers

Answer:

The answer should be: 1.20 A

Explanation:

Which of the following is evidence for continental drift?

Answers

They based their idea of continental drift on several lines of evidence: fit of the continents, paleoclimate indicators, truncated geologic features, and fossils.

absolute potential difference ,due of point charge of 1C at a distance of 1 m is given by

Answers

Answer:

[tex] \implies U = \dfrac{kq}{r} [/tex]

[tex]\implies U = \dfrac{9 \times {10}^{9} \times 1}{1} [/tex]

[tex]\implies U = 9 \times {10}^{9} \: J[/tex]

We have that absolute potential difference ,due of point charge of 1C at a distance of 1 m is given by

[tex]\rho=9x10 ^{10}J[/tex]

From the question we are told that

point charge of 1C at a distance of 1 m

Generally the equation for the Electrostatic potential energy  is mathematically given as

[tex]\rho=\frac{kq_1q_2}{r}[/tex]

Where k is a constant

[tex]k=9*10^9Nm^2/c^2[/tex]

Therefore

[tex]\rho=\frac{(9*10^9)1*10^(-6)*1*10^{-6}}{1}[/tex]

[tex]\rho=9x10 ^{10}J[/tex]

For more information on this visit

https://brainly.com/question/12319416?referrer=searchResults

For saving lives, what is the most important safety feature on a car? A. Air bag B. Safety Belt C. Anti-lock brakes

Answers

i'd imagine the answer is safety belt, but i don't have anything to back that up with

For saving lives  the most important safety feature on a car is B. Safety Belt

What are safety features of  a car ?

Safety features of  a car is a feature of a product designed to ensure or increase safety.

Air bag and Anti-lock brakes are the supplemental protection and designed to work best with combination with seat bells.

Air bag reduce the chance that upper body or head will strike the vehicle's interior during a crash alongside with belt that will  also hold your upper body

so, the primary safety feature is seat belt and Air bag and Anti-lock brakes  comes in secondary safety feature  as they increases the safety and risk of getting an injury during any accident

correct answer is B. Safety Belt

learn more about Safety features

https://brainly.com/question/25820562?referrer=searchResults

#SPJ3

A pendulum of mass 18 kg is released from rest at some height, as shown by
point A in the image below. At the bottom of its arc at point B, it is traveling at
a speed of 17 m/s. What is the approximate amount of energy that has been
lost due to friction and air resistance? (Recall that a=98 m/s2

Answers

By the work-energy theorem, the total work done on the mass as it swings is

W = ∆K = 1/2 (18 kg) (17 m/s)² = 153 J

No work is done by the tension in the string, since it's directed perpendicular to the mass at every point in the arc. Similarly, the component of the mass's weight mg pointing perpendicular to the arc also performs no work.

If we ignore friction/drag for the moment, the only remaining force is the parallel component of weight, which performs mgh = (176.4 N) h of work, where h is the vertical distance between points A and B.

Now, if w is the amount of work done by friction/air resistance, then

(176.4 N) h - w = 153 J

If you know the starting height h, then you can solve for w.

Is a nanoliter greater then one liter?

Answers

No, a nanoliter is one billionth of one liter

if the pelican in item 3 was traveling at the same speed but was only 2.7m above the water, how far would the fish travel horizontally before hitting the water?​

Answers

Answer:

5.66 m

Explanation:

From online sources, the speed in item 3 being referred to was discovered to be 7.62 m/s

Now, let's get the time of flight from one of Newton's equation of motion;

S = ut + ½gt²

Considering the vertical component, we have u = 0 m/s.

Thus;.

S = ½gt²

Plugging in the relevant values;

2.7 = ½ × 9.8 × t²

t² = 2.7/4.9

t = √(2.7/4.9)

t = 0.7423 s

Now, when we consider the horizontal component of the motion, we have;

S = vt

Where;

S is the distance the fish will travel horizontally before hitting the water.

v = 7.62 m/s

t = 0.7423

Thus

s = 7.62 × 0.7423

s ≈ 5.66 m

the direction of applied force has to be_____ to the distance in order to say work is done

Answers

Answer:

Explanation:

The direction of the applied force has to be parallel to the distance an object moved in order to say that work has been done.

un litro de un gas es calentado a presión constante desde 20°C hasta 60°C que volumen final ocupará dicho gas? ​

Answers

Answer:

Final volume, V2 = 3 Litres

Explanation:

Given the following data;

Initial volume, V1 = 1 litre

Initial temperature, T1 = 20°C

Final temperature, T2 = 60°C

To find the final volume, we would use Charles' law;

Charles states that when the pressure of an ideal gas is kept constant, the volume of the gas is directly proportional to the absolute temperature of the gas.

Mathematically, Charles is given by;

V1/T1 = V2/T2

Making V2 as the subject formula, we have;

V1T2 = V2T1

V2 = (V1T2)/T1

Substituting into the formula, we have;

V2 = (1 * 60)/20

V2 = 60/20

Final volume, V2 = 3 Litres

A parallel combination of a 1.47 μF capacitor and a 2.95 μF capacitor is connected in series to a 4.89 μF capacitor. This three‑capacitor combination is connected to a 15.5 V battery. Determine the charge on each capacitor.

Answers

Answer:

a. i. 35.96 μC  b. i. 11.98 μC ii. 24.04 μC

Explanation:

We need to find the total capacitance of the system C.

The total capacitance of the parallel combination of a 1.47 μF capacitor and a 2.95 μF capacitor is C' = 1.47 μF + 2.95 μF = 4.42 μF.

C' = 4.42 μF is in series with the 4.89 μF capacitor and for a series combination of capacitors, we have the total capacitance, C from

1/C = 1/4.42 μF + 1/4.89 μF

1/C = (4.42 μF + 4.89 μF)/(4.42 μF × 4.89 μF)

1/C = 9.31 μF/21.6138 μF²

C = 21.6138/9.31 μF

C = 2.32 μF

So, the total charge in the circuit Q = CV where C = total capacitance = 2.32 μF and v = voltage = 15.5 V

So, Q = CV

Q = 2.32 μF × 15.5 V

Q = 35.96 μC

i. The charge on the 4.89 μF capacitor

Since the 4.89 μF is in series with C', the total charge flowing i the circuit is the total charge in the 4.89 μF capacitor. So, its charge Q = 35.96 μC

b. The charge in the 1.47 μF and 2.95 μF capacitors.

To find the charge in the 4.89 μF and 2.95 μF capacitors, we need to find the voltage across the combined parallel combination of a 1.47 μF capacitor and a 2.95 μF capacitor. The voltage, V' across the 4.89 μF capacitor, since Q = CV', V' = Q/C = 35.96 μC/4.89 μF = 7.35 V

So, the voltage V" across the combined parallel combination of a 1.47 μF capacitor and a 2.95 μF capacitor, C' is V" = 15.5 V - V' (since V' + V" = 15.5 V).

So, V" = 15.5 V - V'

V" = 15.5 V - 7.35 V

V" = 8.15 V

i. The charge on the 1.47 μF capacitor

Using Q' = CV" where Q' = charge across capacitor, C = 1.47 μF and V" = 8.15 V.

So, Q' = CV"

Q' = 1.47 μF × 8.15 V

Q' = 11.98 μC

ii. The charge on the 2.95 μF capacitor

Using Q" = CV" where Q' = charge across capacitor, C = 2.95 μF and V" = 8.15 V.

So, Q" = CV"

Q" = 2.95 μF × 8.15 V

Q" = 24.04 μC

Pls help asap!!

A bucket contains hot water at 95°c. A man wants to bath with water at 40°c. What is the ratio of the mass of hot water to the mass of cold water that he needs.​

Answers

Answer:

55

Explanation:95-40=55

i hope i did the math right if i didnt please tell me

What is the relationship between electric field lines and equipotential lines that you observed in doing the lab

Answers

Answer:

Explained below

Explanation:

Generally speaking, we know in physics that Electric field lines are lines which usually start at positive charges and deflect away from them to terminate at the negative charges. Meanwhile Equipotential lines are lines that are used to connect points located on the same electric potential.

Finally, in conclusion, electric field lines are usually lines that go through in a perpendicular manner across every equipotential lines.

An ice-skater with a mass of 80kg is holding a bowling ball with a mass of 8 kg. Suppose that the skater tosses the bowling ball forward with a speed of 6 m/s. What is the skater's reactive velocity? Show all work.

Answers

Answer:

0.6 m/s

Explanation:

The details of the masses and velocities are;

The mass of the ice skater, m₁ = 80 kg

The mass of the ball, m₂ = 8 kg

The speed with which the skater tosses the ball forward, v₂ = 6 m/s

Therefore;

According to the principle of conservation of linear momentum, we have;

m₁·v₁ = m₂·v₂

Where;

v₁ = The skater's reactive velocity

Therefore, we get;

80 kg × v₁ = 8 kg × 6 m/s

v₁ = 8 kg × 6 m/s/(80 kg) = 0.6 m/s

The skater's reactive velocity, v₁ = 0.6 m/s.

Which wave has the smallest amplitude?

Answers

Answer:

C. C

Explanation:

A wave can be defined as a disturbance in a medium that progressively transports energy from a source location to another location without the transportation of matter.

In Science, there are two (2) types of wave and these include;

I. Electromagnetic waves: it doesn't require a medium for its propagation and as such can travel through an empty space or vacuum. An example of an electromagnetic wave is light.

II. Mechanical waves: it requires a medium for its propagation and as such can't travel through an empty space or vacuum. An example of a mechanical wave is sound.

A crest can be defined as the highest (vertically) point on a waveform.

On a related note, a trough is the lowest (vertically) on a waveform.

An amplitude can be defined as a waveform that's measured from the center line (its origin or equilibrium position) to the bottom of a trough or top of a crest. Thus, the vertical axis (y-axis) is the amplitude of a waveform i.e it's measured vertically.

In this scenario, waveform C which is represented by a blue curvy line has the smallest amplitude in comparison with the other waveforms because it has the minimum height when measured from the origin.

In contrast, waveform A represented by a purple line has the highest amplitude because it has the maximum height when measured from the origin.

Mathematically, the amplitude of a wave is given by the formula;

x = Asin(ωt + ϕ)

Where;

x is displacement of the wave measured in meters.A is the amplitude.ω is the angular frequency measured in rad/s.t is the time period measured in seconds.ϕ is the phase angle.

Answer:

The answer is indeed D as the comment above suggests.

Explanation:

Simply put, wave D's highest point is closer to the line than all of the other high points of A, B and C

An electron enters the magnetic field at right angle from left B into paper. The electron will be deflected?

Answers

Answer:

According to this direction of force is perpendicular to the direction of current and magnetic field. Therefore force is opposite to electron into the paper at 90°.

Kevin used a pulley to lift a piano to the third floor of his apartment. His input work was 12,000 J and the output work was 10,000 J. What was the mechanical efficiency of the pulley?

A . 50%
B. 83.3%
C . 120%
D. 16.7%

Answers

Answer:

B

Explanation:

Eff = output work/input work ×100

Hence, Eff = 10000/12000 × 100

Eff = 83.3%

Why is a flower not a good blackbody radiator?

Answers

Answer:

A flower emits only visible light

A flower reflects much of the light that hits it

which is part of the convection cycle in earths atmosphere?

a. hot, denser air rises
b. cold, denser air rises
c. hot, less-dense air rises
d. cold, less-dense air falls

Answers

I believe it’s C. hot, less-dense air rises

I hope this helps !!!!!!!!

Which wave has the largest amplitude?
A.D
B.B
C.C
D.A

Answers

Answer:

D. A

General Formulas and Concepts:

Simple Harmonic Motion

Parts of a wave

PeriodAmplitudeWavelengthCrest/Trough

Explanation:

The amplitude is the distance from the horizon to either the crest or trough of a wave.

In layman's terms, it is how high the wave is.

The "highest" wave would be wave A.

∴ our answer is D.

Topic: AP Physics 1 Algebra-Based

Unit: SMH

Answer:

A (The wave)

Explanation:

Wave A

Which statement describes why energy is released in a nuclear fission reaction based on mass-energy equivalence?

A. For large nuclei, the mass of the original nucleus is greater than the mass of the products.
B. For large nuclei, the mass of the original nucleus is less than the mass of the products.
C. For small nuclei, the binding energy of the lighter nuclei is greater than the binding energy of the heavier nucleus.
D. For small nuclei, the binding energy of the lighter nuclei is less than the binding energy of the heavier nucleus.

Answers

Answer:

A is the answer!

Explanation:

Edge 2021

Answer:

A

Explanation:

Edge

A rectangular coil of wire, 22.0 cm by 35.0 cm and carrying a current of 1.40 A, is oriented with the plane of its loop perpendicular to a uniform 1.50-T magnetic field pointing into the plane of the loop. Let the loop be in x-y Cartesian plane so that the long and short sides of the loop are parallel to x- and y-axis, respectively. The loop center is at the origin of x-y Cartesian plane. Note that the magnetic field is in the direction of the negative z-axis.a. Calculate: (i) the net force that the magnetic field exerts on the coil; (ii) the torque about the z-axis that the magnetic field exerts on the coil.b. The plane of the coil is now rotated through +30º from its initial orientation (the x-y plane of the Cartesian coordinate system that remains the same). Calculate: (i) the net force that the magnetic field exerts on the coil; (ii) the torque about the rotation axis that the magnetic field exerts on the coil.

Answers

Answer:

a)  [tex]F_{net}=0[/tex]

b)  [tex]T=0[/tex]

Explanation:

From the question we are told that:

Dimensions:

[tex]L*B=22.0*35.0cm[/tex]

Current [tex]I=1.40A[/tex]

Magnetic field [tex]B=1.40[/tex]

Therefore

[tex]Area=L*B[/tex]

[tex]A=22.0*35.0cm[/tex]

[tex]A=770cm=>770*0^{-4}[/tex]

a)

Generally Force on Looping gives

[tex]F_1-F_2[/tex]

[tex]F_3=F_4[/tex]

Therefore

[tex]F_{net}=0[/tex]

b)

Generally the equation for Torque is mathematically given by

[tex]T=i*Asin \theta[/tex]

Since A and B are on opposite direction

[tex]\theta=180[/tex]

Therefore

[tex]T=1.40*770*10^{-4}sin 180[/tex]

[tex]T=0[/tex]

Convertir 25 km/h a m/s

Answers

Answer:

6.9 m/s

Explanation:

1000m = 1km

3600s = 1hr

25000m/3600s

6.9m/s

(d) Below shows a hydraulic press with a pump piston of area 4 cm2 and a ram area of

12 cm2 . IF A force of 300 N is applied on the pump piston, find:

(i)the maximum load on the ram.

(ii) the velocity ratio of the machine.

(iii) the mechanical advantage of the machine.

(iv)the efficiency of the machine.

Answers

Answer:

Explanation:

hi

what is the source of energy​

Answers

Fossil Fuels is the largest source for energy

Hope this is what you were asking :)
Other Questions
cloud offers better protection compare to on premise? You are skiing down a mountain with a vertical height of 1250 feet. The distance that you ski as you go from the top down to the base of the mountain is 3350 feet. Find the angle of elevation from the base to the tep of the mountain. Round your answer to a whole number as necessary. According to Durkheim,was a key feature of preindustrial societies while-was a key feature of industrial societies. In what way did the Greek civilization help to build our current cities? 26 Qu cosa ms rara!Escribamos Cul de las cosas no existiaen el ao mencionado?MODELO1736: agua corriente, estufa delea, pozo de agua, rayos X1. 1800: lamparas de gas en la calle, baosdentro de la casa, calefaccin2. 1920: electricidad, televisin, radio3. 1941: avin, coche, nave espacial(spaceship)4. 1875: tren, telegrafo, computadora, pozosde agua5. 1950: telfono, aire acondicionado,computadora personal6. 1965: disco compacto, calefaccin, estufaelctrica F(x, y, z) = (x + yz)i + (y + xz)j + (z + xy)k, Find the divergence of the vector field. Tyrone measured the floor of his rectangular storage unit. It is 3 feet wide and 8 feet from one corner to the opposite corner. How long is the storage unit? If necessary, round to the nearest tenth. How would you describe romanticism (19th century )era/movement? A car starts from rest. if the velocity of car become 15m/s after 20s calculate the acceleration of the car. A central idea in The Code Book is the concern that much of the world's information is not secure. Which lines from thepassage best support this central idea? Check all that apply. The speculative demand for holding money is when people hold money:Group of answer choicesa: to take advantage of changes in interest rates.b: as insurance against unexpected needs.c: to transact purchases they expect to make.d: to speculate in the stock market.e: instead of near money. What effects are produced on environment by industry? HELP!!! I need to know if this is Function or not a function. help me please it's important!! If there are 360 million people living in the U.S, but 1 million died of health issues leaving 289 million eligible workers, what is the unemployment rate if 170 million are in the labor force and 7 million are actively seeking work? The distance AB rounded to the nearest tenth = [?] Penny attended a four year state college. She took out a student loan to pay for her tuition and room & board for the four years she was attending the college. Her tuition fees were $6,970 per year, and the cost of her room and board was $11,320 per year. Now that she has graduated, she will have to start paying back her loan. Fortunately, Penny has a grace period of one year before she has to start paying back the loan. Her loan details are as follows: there is a fixed-rate interest of 4.5% and the interest compounds each month. During her one year grace period, interest will accrue on the loan, so that when she has to start paying the loan back she will owe more than what she owes now. Her goal is to be able to payoff the loan in 10 years. Given all of this information, answer the following questions:1. What is the original loan amount, i.e. how much were the total costs for tuition plus room & board for the four years that Penny attended the college?2. What is the new loan amount after the one-year grace period (remember that interest will accrue on the loan during this initial 12-month period that she is not paying anything back on the loan)? This is the amount that she will be responsible for paying back. (Round your answer to the nearest whole dollar)3. Given that she can pay back the loan in full after 10 years of payments, what is the total amount she will end up paying back (both principal and interest that has accrued over the 10 years)? And how much will her monthly payments on the loan be for those 10 years? (Round your answers to the nearest whole dollar) When thinking about all 4 types of macromolecules discussed, which of the following statements are true? Select all that apply.Monomers are linked together by hydrolysis.Monomers are joined together to form functional polymersMonomers are linked together by dehydration synthesis.Monomers join together via hydrogen bonds. use the prime factors of 3136 and 2744 to evaluate:3136/32744 equation of the line which passes through point (0,5) at gradient of - 1