If a boy lifts a mass of 6kg to a height of 10m and travels horizontally with a constant velocity of 4.2m/s, calculate the work done? Explain your answer.
Answer:
W = 641.52 J
Explanation:
The work done here will be the sum of potential energy and the kinetic energy of the boy. Here potential energy accounts for vertical motion part while the kinetic energy accounts for the horizontal motion part:
[tex]Work\ Done = Kinetic\ Energy + Potential\ Energy\\\\W = K.E +P.E\\\\W = \frac{1}{2}mv^2+mgh\\\\[/tex]
where,
W = Work Done = ?
m = mass = 6 kg
v = speed = 4.2 m/s
g = acceleration dueto gravity = 9.81 m/s²
h = height = 10 m
Therefore,
[tex]W = \frac{1}{2}(6\ kg)(4.2\ m/s)^2+(6\ kg)(9.81\ m/s^2)(10\ m)[/tex]
W = 52.92 J + 588.6 J
W = 641.52 J
A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses (velocity = 0) for a fraction of a second at the very top before heading down the other side.
a) Draw a sankey diagram for a roller coaster's climb.
A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses for a fraction of a second at the very top before heading down the other side. At the top of the hill total, the kinetic energy of the roller coaster would be zero as the velocity is zero at the top of the hill, therefore the total mechanical energy is only because of potential energy.
What is mechanical energy?Mechanical energy is the combination of all the energy in motion represented by total kinetic energy and the total stored energy in the system which is represented by total potential energy.
The expression for total mechanical energy is as follows
ME= KE+PE
As total mechanical energy is the sum of all the kinetic as well as potential energy stored in the system.As given in the problem a roller coaster uses 800000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy which means 300000 J of energy is lost in the frictional energy while climbing the hill,
Thus at the top of the hill, the total energy of the roller coasters is only due to the potential energy.
Learn more about mechanical energy from here brainly.com/question/12319302
#SPJ2
Parallel Wires: Two long, parallel wires carry currents of different magnitudes. If the current in one of the wires is doubled and the current in the other wire is halved, what happens to the magnitude of the magnetic force that each wire exerts on the other?
Answer:
Explanation:
Given force between 2 currents carrying
wires = F₀
Magnetic force between the2 wires =F₀= (μ₀/4π) x ( 2 (μ₀/4π) x ( 2I₁I₂ / μ) x L
where I₁=Current in wire 1
I₂= Current in wire 2
L= Length of the wire
when one current is doubled and the other is halved
I₁= 2 I₁
I₂= I₂/2
F₀ = (μ₀/4π) x ( 2× (2I₁) (I₂/2) / μ) x L
As the speed of a particle approaches the speed of light, the momentum of the particle Group of answer choices approaches zero. decreases. approaches infinity. remains the same. increases.
Answer:
approaches infinity
Explanation:
There are two momentums, the classical momentum which is equal to the product of mass and velocity, and the relativistic momentum, the one we should look at when we work with high speeds, and this happens because massive objects have a speed limit, in this case, we are approaching the speed of light, so we need to work with the relativistic momentum instead of the classical momentum.
The relativistic momentum can be written as:
[tex]p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]
where
u = speed of the object relative to the observer, in this case we have that u tends to c, the speed of light.
m = mass of the object
c = speed of light.
So, as u tends to c, we will have:
[tex]\lim_{u \to c} p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]
Notice that when u tends to c, the denominator on the first term tends to zero, thus, the relativistic momentum of the object will tend to infinity.
Then the correct option is infinity, as the particle speed approaches the speed of light, the relativistic momentum of the particle tends to infinity.
I need help with this please!!!!
Answer:
1.84 hours
I hope it's helps you
In the following experiments, identify the independent and dependent variable.
Answer:
in what experements
Explanation:
Trình bày những hiểu biết của em về đại lượng vận tốc dài, vận tốc góc(định nghĩa, công thức, ý nghĩa, đơn vị, loại đại lượng).
Convert 385k to temperature of
Answer:
233.33°F
Explanation:
(385K - 273.15) * 9/5 + 32 = 233.33°F
Express 6revolutions to radians
Answer:
About 37.70 radians.
Explanation:
1 revolution = 2[tex]\pi[/tex] radians
∴ 6 revolutions = (6)(2[tex]\pi[/tex] radians)
6 revolutions = 37.6991 or ≈ 37.70 radians
A solenoid has a length , a radius , and turns. The solenoid has a net resistance . A circular loop with radius is placed around the solenoid, such that it lies in a plane whose normal is aligned with the solenoid axis, and the center of the outer loop lies on the solenoid axis. The outer loop has a resistance . At a time , the solenoid is connected to a battery that supplies a potential . At a time , what current flows through the outer loop
This question is incomplete, the complete question is;
A solenoid has a length 11.34 cm , a radius 1.85 cm , and 1627 turns. The solenoid has a net resistance of 144.9 Ω . A circular loop with radius of 3.77 cm is placed around the solenoid, such that it lies in a plane whose normal is aligned with the solenoid axis, and the center of the outer loop lies on the solenoid axis. The outer loop has a resistance of 1651.6 Ω. At a time of 0 s , the solenoid is connected to a battery that supplies a potential 34.95 V. At a time 2.58 μs , what current flows through the outer loop?
Answer:
the current flows through the outer loop is 1.3 × 10⁻⁵ A
Explanation:
Given the data in the question;
Length [tex]l[/tex] = 11.34 cm = 0.1134 m
radius a = 1.85 cm = 0.0185 m
turns N = 1627
Net resistance [tex]R_{sol[/tex] = 144.9 Ω
radius b = 3.77 cm = 0.0377 m
[tex]R_o[/tex] = 1651.6 Ω
ε = 34.95 V
t = 2.58 μs = 2.58 × 10⁻⁶ s
Now, Inductance; L = μ₀N²πa² / [tex]l[/tex]
so
L = [ ( 4π × 10⁻⁷ ) × ( 1627 )² × π( 0.0185 )² ] / 0.1134
L = 0.003576665 / 0.1134
L = 0.03154
Now,
ε = d∅/dt = [tex]\frac{d}{dt}[/tex]( BA ) = [tex]\frac{d}{dt}[/tex][ (μ₀In)πa² ]
so
ε = μ₀n [tex]\frac{dI}{dt}[/tex]( πa² )
ε = [ μ₀Nπa² / [tex]l[/tex] ] [tex]\frac{dI}{dt}[/tex]
ε = [ μ₀Nπa² / [tex]l[/tex] ] [ (ε/L)e^( -t/[tex]R_{sol[/tex]) ]
I = ε/[tex]R_o[/tex] = [ μ₀Nπa² / [tex]R_o[/tex][tex]l[/tex] ] [ (ε/L)e^( -t/[tex]R_{sol[/tex]) ]
so we substitute in our values;
I = [ (( 4π × 10⁻⁷ ) × 1627 × π(0.0185)²) / (1651.6 ×0.1134) ] [ ( 34.95 / 0.03154)e^( -2.58 × 10⁻⁶ / 144.9 ) ]
I = [ 2.198319 × 10⁻⁶ / 187.29144 ] [ 1108.116677 × e^( -1.7805 × 10⁻⁸ )
I = [ 1.17374 × 10⁻⁸ ] × [ 1108.116677 × 0.99999998 ]
I = [ 1.17374 × 10⁻⁸ ] × [ 1108.11665 ]
I = 1.3 × 10⁻⁵ A
Therefore, the current flows through the outer loop is 1.3 × 10⁻⁵ A
Answer:
1.28 *10^-5 A
Explanation:
Same work as above answer. Needs to be more precise
How do you know that a liquid exerts pressure?
Answer:
The pressure of water progressively increases as the depth of the water increases. The pressure increases as the depth of a point in a liquid increases. The walls of the vessel in which liquids are held are likewise subjected to pressure. The sideways pressure exerted by liquids increases as the liquid depth increases.
What Are the type's of Tidal turbines?
Answer:
Types of tidal turbines
Axial turbines.
Crossflow turbines.
Flow augmented turbines.
Oscillating devices.
Venturi effect.
Tidal kite turbines.
Turbine power.
Resource assessment.
Answer:
Axial turbines
Crossflow turbines
flow augmented turbines
A regulation soccer field for international play is a rectangle with a length between 100 m and a width between 64 m and 75 m. What are the smallest and largest areas that the field could be?
Answer:
The smallest and largest areas could be 6400 m and 7500 m, respectively.
Explanation:
The area of a rectangle is given by:
[tex] A = l*w [/tex]
Where:
l: is the length = 100 m
w: is the width
We can calculate the smallest area with the lower value of the width.
[tex] A_{s} = 100 m*64 m = 6400 m^{2} [/tex]
And the largest area is:
[tex] A_{l} = 100 m*75 m = 7500 m^{2} [/tex]
Therefore, the smallest and largest areas could be 6400 m and 7500 m, respectively.
I hope it helps you!
Answer:
the largest areas that the field could be is [tex]A_l[/tex]=7587.75 m
the smallest areas that the field could be is [tex]A_s[/tex]=6318.25 m
Explanation:
to the find the largest and the smallest area of the field measurement error is to be considered.
we have to find the greatest possible error, since the measurement was made nearest whole mile, the greatest possible error is half of 1 mile and that is 0.5m.
therefore to find the largest possible area we add the error in the mix of the formular for finding the perimeter with the largest width as shown below:
[tex]A_l[/tex]= (L+0.5)(W+0.5)
(100+0.5)(75+0.5) = (100.5)(75.5) = 7587.75 m
To find the smallest length we will have to subtract instead of adding the error factor value of 0.5 as shown below:
[tex]A_s[/tex]= (L-0.5)(W-0.5)
(100-0.5)(64-0.5) = (99.5)(63.5) = 6318.25 m
When you shine a beam of light, which is composed of just two different colors, red and green, onto a diffraction grating which color gets diffracted more
Answer:
The diffraction grating separates light into colors as the light passes through the many fine slits of the grating. This is a transmission grating. ... The prism separates light into colors because each color passes through the prism at a different speed and angle.
If you dive underwater, you notice an uncomfortable pressure on your eardrums due to the increased pressure. The human eardrum has an area of about 70 mm217 * 10-5 m22, and it can sustain a force of about 7 N without rupturing. If your body had no means of balancing the extra pressure (which, in reality, it does), what would be the maximum depth you could dive without rupturing your eardrum
Answer:
[tex]h=10m[/tex]
Explanation:
From the question we are told that:
Area [tex]a=70 x 10^{-6}[/tex]
Force [tex]F=7N[/tex]
Generally the equation for Pressure is mathematically given by
Pressure = Force/Area
[tex]P=\frac{F}{A}[/tex]
[tex]P=\frac{ 7}{(70 * 10^{-6})}[/tex]
[tex]P= 1*10^{5} Pa[/tex]
Generally the equation for Pressure is also mathematically given by
[tex]P=hpg[/tex]
Therefore
[tex]h=\frac{P}{hg}[/tex]
[tex]h=\frac{10000}{1000*9.8}[/tex]
[tex]h=10m[/tex]
1 Poin Question 4 A 85-kg man stands in an elevator that has a downward acceleration of 2 m/s2. The force exerted by him on the floor is about: (Assume g = 9.8 m/s2) А ON B 663 N C) 833 N D) 1003 N
Answer:
D) 1003 N
Explanation:
Given the following data;
Mass of man = 85 kg
Acceleration of elevator = 2 m/s²
Acceleration due to gravity, g = 9.8 m/s²
To find the force exerted by the man on the floor;
Force = mg + ma
When the lightbulbs were used as the resistors, you observed only a flash of light, as opposed to a continuous glow. Explain why that behavior is expected. After all, the light bulb is directly connected to the power supply.
Solution :
Whenever the lightbulbs are used as resistors, we throw the switch to the left. This allows the current to flow through the circuit which causes the bulb to glow and also the capacitor gets charged. When the capacitor gets fully charged, the electric field becomes constant between its two plates. Now there is no displacement current induced in the plates of the capacitor. The capacitor works as an open switch and the bulb gets switched off.
And thus the bulb flashes for the moment as opposed to continuous glow.
2- A student ran 135 meters in 15 seconds. What was the student's velocity?
*
7.5 m/s
9 m/s
12 m/s
15 m/s
Answer:
9 Brainly hahaha ............huh
Si un resorte de constante elástica 1300 n/m se comprime 12 cm ¿Cuanta energía almacena? Y si estira 12cm ¿Cuanta energía almacena?
La energía que almacena el resorte cuando se comprime y estira 12 cm es 9,4 J.
La energía potencial elástica del resorte se puede calcular con la siguiente ecuación:
[tex] E_{p} = \frac{1}{2}kx^{2} [/tex]
En donde:
k: es la constante del resorte = 1300 N/m
x: es la distancia de compresión o de elongación = 12 cm = 0,12 m
Dado que la energía es proporcional al cuadrado de la distancia recorrida por el resorte (x), la energía almacenada por el resorte durante la compresión será la misma que la energía almacenada por la elongación.
Por lo tanto, la energía almacenada es:
[tex]E_{p} = \frac{1}{2}kx^{2} = \frac{1}{2}1300 N/m*(0,12 m)^{2} = 9,4 J[/tex]
Entonces, la energía del resorte cuando se comprime y cuando se estira es la misma, a saber 9,4 J.
Para saber más sobre energía potencial visita este link: https://brainly.com/question/156316?referrer=searchResults
Espero que te sea de utilidad!
Answer:
Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.
Explanation:
La Energía Potencial Elástica almacenada por el resorte ([tex]U_{e}[/tex]), en joules, se calcula a partir de la Ley de Hooke, la definición de Trabajo y el Teorema del Trabajo y la Energía, cuya expresión se presenta abajo:
[tex]U_{e} = \frac{1}{2}\cdot k\cdot (x_{f}^{2}-x_{o}^{2})[/tex] (1)
Donde:
[tex]k[/tex] - Constante elástica del resorte, en newtons por metro.
[tex]x_{o}[/tex] - Posición inicial del resorte, en metros.
[tex]x_{f}[/tex] - Posición final del resorte, en metros.
Nótese que el resorte sin deformar tiene una posición de cero, la tensión tiene un valor positivo y la compresión, negativo.
Asumiendo que en ambos casos el resorte se encuentra inicialmente sin deformar, se reduce (1) a una forma de función par, es decir, una función que cumple con la propiedad de que [tex]f(x) = f(-x)[/tex], se encuentra que al comprimirse o estirarse en la misma medida almacena la misma cantidad de energía.
La cantidad de energía a almacenar es:
[tex]U_{e} = \frac{1}{2}\cdot \left(1300\,\frac{N}{m} \right)\cdot (0,12\,m)^{2}[/tex]
[tex]U_{e} = 9,360\,J[/tex]
Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.
A wire, 0.60 m in length, is carrying a current of 2.0 A and is placed at a certain angle with respect to the magnetic field of strength 0.30 T. If the wire experiences a force of 0.18 N, what angle does the wire make with respect to the magnetic field
Answer:
[tex]\theta=30 \textdegree[/tex]
Explanation:
From the question we are told that:
Current [tex]I=2.0A[/tex]
Length [tex]L=0.60m[/tex]
Magnetic field [tex]B=0.30T[/tex]
Force [tex]F=0.18N[/tex]
Generally the equation for Force is mathematically given by
[tex]F = BIL sin\theta[/tex]
[tex]sin\theta=\frac{F}{BIL}[/tex]
[tex]\theta=sin^{-1}\frac{0.18}{0.3*2*0.6}[/tex]
[tex]\theta=30 \textdegree[/tex]
1. A sequence of potential differences v is applied accross a wire (diameter =0.32 mm length = 11 cm and the resulting current I are measured as follows: V 0.1 0.2 0.3 0.4 0.5 I (MA) 72 144 216 288 360 2) a) plot a graph of v against I.
b) determine the wire's resistence , R.
c) State ohm's law and try to relate it . your results.
Answer:
a. Find the graph in the attachment
b. 720 kΩ
c. The ratio V/I gives us our resistance which is 720 kΩ
Explanation:
a) plot a graph of V against I.
To plot the graph of V against I, we plot the corresponding points against each other. With the voltage V measured in volts and the current I measured in mA, the plotted graph is in the attachment.
b) Determine the wire's resistance , R.
The resistance of the wire is determined as the gradient of the graph.
R = ΔV/ΔI = (V₂ - V₁)/(I₂ - I₁)
Taking the first two corresponding measurements. V₁ = 72 V, I₁ = 0.1 mA, V₂ = 144 V and I₂ = 0.2 mA
R = (144 V - 72 V)/(0.2 - 0.1) mA
R = 72 V/0.1 mA
R = 72 V/(0.1 × 10⁻³ A)
R = 720 × 10³ V/A
R = 720 kΩ
c) State ohm's law and try to relate it your results.
Ohm's law states that the current flowing through a conductor is directly proportional to the voltage across it provided the temperature and all other physical conditions remain constant.
Mathematically, V ∝ I
V = kI
V/I = k = R
Since the ratio V/I = constant, from our results, the ratio of V/I for each reading gives us the resistance. Since we have a linear relationship between V and I, the gradient of the graph is constant and for each value of V and I, the ratio V/I is constant. So, the ratio V/I gives us our resistance which is 720 kΩ.
Since V/I is constant, we thus verify Ohm's law.
how will be electric lines of force where intensity of electric field is maximum ?
a. wider
b. +ve to -ve
c. narrow
d. -ve to +ve
i'm pretty sure the answer is A wider
Electric lines of force where intensity of electric field is maximum when its wider.
What is Electric field?The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (also known as an E-field. It can also refer to a system of charged particles' physical field.
Electric charges and time-varying electric currents are the building blocks of electric fields. The electromagnetic field, one of the four fundamental interactions (also known as forces) of nature, manifests itself in both electric and magnetic fields.
Electrical technology makes use of electric fields, which are significant in many branches of physics. For instance, in atomic physics and chemistry, the electric field acts as an attracting force to hold atoms' atomic nuclei and electrons together.
Therefore, Electric lines of force where intensity of electric field is maximum when its wider.
To learn more about electric field, refer to the link:
https://brainly.com/question/1443103
#SPJ2
A ball is launched from the ground with a horizontal speed of 30 m/s and a vertical speed of 30 m/s. How far horizontally will it travel in 2 seconds?
A. 30 m
B. 90 m
C. 45 m
D. 60 m
Answer:
It will travel Vx * t = 30 m/s * 2 s = 60 m
which characteristic of nuclear fission makes it hazardous?
Answer:The radioactive waste
Explanation:Fission is the splitting of a heavy unstable nucleus into two Lighter nuclei
Identify the factors that affect the intensity of radiation detected from a radioactive source. Select one or more: The color of the source Type of emission from the source Distance of the detector from the source Type of materials between the source and the detector
The intensity of radiation is the defined as amount of energy per surface angle which can be used to determine the amount of energy emitting from a source that will hit another surface.
The factors that affect the intensity of radiation are
Type of emission from the source :This can be alpha, gamma, beta or electromagnetic rays etc
Distance of the detector from the source: The shorter the distance between the source and the detector, the more the effect and vice versa for the longer the distance.
Type of materials between the source and the detector: The type of material between the source and the detector will tell how absorbing and penetrating the radiation is.
Read more on Radiation Intensity here: https://brainly.com/question/10148635
state the laws of reflection
Answer:
Explanation:
The law of reflection says that the reflected angle (measured from a vertical line to the surface called the normal) is equal to the reflected angle measured from the same normal line.
All other properties of reflection flow from this one statement.
How much amount of water can be decomposed
through electrolysis by passing 2 F charge?
Answer:
So, with 2 Faraday of electricity, we can decompose (2/4 × 2) = 1 mole of water. So 18 grams of water is decomposed.
A car is driving towards an intersection when the light turns red. The brakes apply a constant force of 1,398 newtons to bring the car to a complete stop in 25 meters. If the weight of the car is 4,729 newtons, how fast was the car going initially
Answer:
the initial velocity of the car is 12.04 m/s
Explanation:
Given;
force applied by the break, f = 1,398 N
distance moved by the car before stopping, d = 25 m
weight of the car, W = 4,729 N
The mass of the car is calculated as;
W = mg
m = W/g
m = (4,729) / (9.81)
m = 482.06 kg
The deceleration of the car when the force was applied;
-F = ma
a = -F/m
a = -1,398 / 482.06
a = -2.9 m/s²
The initial velocity of the car is calculated as;
v² = u² + 2ad
where;
v is the final velocity of the car at the point it stops = 0
u is the initial velocity of the car before the break was applied
0 = u² + 2(-a)d
0 = u² - 2ad
u² = 2ad
u = √2ad
u = √(2 x 2.9 x 25)
u =√(145)
u = 12.04 m/s
Therefore, the initial velocity of the car is 12.04 m/s
A car accelerates from 0 m/s to 25 m/s in 5 seconds. What is the average acceleration of the car.
Answer:
5 m/s I hope it will help you
Explanation:
mark me as a brainlist answer
An ideal double slit interference experiment is performed with light of wavelength 640 nm. A bright spot is observed at the center of the resulting pattern as expected. For the 2n dark spot away from the center, it is known that light passing through the more distant slit travels the closer slit.
a) 480 nm
b) 600 nm
c) 720 nm
d) 840 nm
e) 960 nm
Answer:
960 nm
Explanation:
Given that:
wavelength = 640 nm
For the second (2nd) dark spot; the order of interference m = 1
Thus, the path length difference is expressed by the formula:
[tex]d sin \theta = (m + \dfrac{1}{2}) \lambda[/tex]
[tex]d sin \theta = (1 + \dfrac{1}{2}) 640[/tex]
[tex]d sin \theta = ( \dfrac{3}{2}) 640[/tex]
dsinθ = 960 nm
