Answer: The ion that contribute to water hardness are:
--> a. Ca2+
--> b. (HCO)3^- and
--> c. Mg2+
While K+ DOES NOT contribute to water hardness.
Explanation:
WATER in chemistry is known as a universal solvent. This is so because it is polar in nature and dissolves most inorganic solutes and some polar organic solutes to form aqueous solutions. It is composed of elements such as hydrogen and oxygen in the combined ratio of 2:1.
Water is said to be HARD if it does not lather readily with soap. There are two types of water hardness:
--> Permanent hardness: This is mainly due to the presence of CALCIUM and MAGNESIUM ions in the form of soluble tetraoxosulphate(VI) and chlorides. These ions are removed by adding washing soda or caustic soda.
--> Temporary hardness: This is due to the presence of calcium HYDROGENTRIOXOCARBONATES. It can be removed by boiling and using slaked lime.
Therefore from the above given ions, Ca2+,(HCO)3^- and Mg2+ contributes to water hardness.
Write a balanced equation for the combination reaction described, using the smallest possible integer coefficients. When methane (CH4) combines with carbon tetrachloride , dichloromethane (CH2Cl2) is formed.
Answer:
C H₄ + C Cl₄ = 2 (C H₂ Cl₂)
5-Analysis of a 12.04-g sample of a liquid compound composed of carbon, hydrogen, and nitrogen showed it to contain 7.34 g C, 1.85 g H, and 2.85 g N. What is the percent composition of this compound
Answer:
%C = 60.9%; %H = 15.4%; %N = 23.7%
Explanation:
Step 1: Given data
Mass of the sample (m): 12.04 gMass of Carbon (mC): 7.34 gMass of Hydrogen (mH): 1.85 gMass of Nitrogen (mN): 2.85 gStep 2: Calculate the percent composition of this compound
To calculate the percent by mass of any element (E), we will use the following expression.
%E = mE/m × 100%
%C = 7.34 g/12.04 g × 100% = 60.9%
%H = 1.85 g/12.04 g × 100% = 15.4%
%N = 2.85 g/12.04 g × 100% = 23.7%
what is a property of every mixture
Explanation:
can u post a picture of the question ?
Propose two steps that could be taken to reduce the vulnerability of the US to hurricanes. Explain why you think those would be effective in saving lives and property.
This is not just about planning and design of buildings and towns/cities, even though those are very important. You could write about the role of research in science and technology and their contributions to emergency preparedness.
You must write at least one paragraph (roughly 150 words).
Answer:
Sensors and evacuation planning.
Explanation:
Sensors that provides information about hurricane and evacuation planning are the two steps that can reduce the vulnerability of the United States to hurricanes. Sensors provides information about hurricane so we can prepare ourselves about it and the evacuation plan helps in order to quick displacement of people from the hurricane area so these two steps can reduce the vulnerability of the US to hurricanes.
Which one is the ionic compound?
Answer:
NAF IS AN IONIC COMPOUND
Explanation:
Answer:
Explanation:
CO2 is a covalent bonding. It is something from the middle of the periodic table bonded with something on the right of the periodic table. It is not ionic.
NH3 is also covalent. The H bonds with the N and the H has properties that resemble both the metals and non metals. That's why it is on both the left and right sides of the periodic table. In this case, it is more non metallic than metallic. Since Nitrogen is on the right side of the table, you have a situation where 2 nonmetals are bonding. It is not ionic.
The answer is NaF. Sodium is on the left side of the periodic table and F is on the right side. That's what it takes to get an ionic bond.
After mixing the solutions in a separatory funnel, the stopper should be ______ and the liquid should be _______ and the layers allowed to separate. When you get close to the interface between the layers, ______ the funnel and turn over _______ heat up until the first layer is collected get eye level with to collect the second layer. _______
Answer:
Hence,
1) removed
2) drained through the stopcock
3) get eye level with
4) slow the draining
5) switch to a new flask
Explanation:
After mixing the solutions in a separatory funnel, the stopper should be removed and the liquid should be drained through the stopcock, and the layers allowed to separate. When you get close to the interface between the layers, get eye level with the funnel and turn over to slow the draining heat up until the first layer is collected. Switch to a new flask get eye level with it to collect the second layer.
Give reason: The maximum covalence of boron is 4.
Answer:
true
Explanation:
Answer:
true
Explanation:
What is Sublimation?-.-
Explanation:
Sublimation is the conversion between the solid and the gaseous phases of matter, with no intermediate liquid stage
How do enzymes function in biological reactions?
Answer:
it binds molecules like a chemical bond-breaking
Explanation:
Enzymes perform the critical task of lowering a reaction's activation energy—that is, the amount of energy that must be put in for the reaction to begin. Enzymes work by binding to reactant molecules and holding them in such a way that the chemical bond-breaking and bond-forming processes take place more readily.
Stomach acid is approximately 0.10 M HCl. How many mL of stomach acid can be neutralized by one regular antacid tablet that contains 500 mg of solid CaCO3 (100.09 g/mol)?
Answer:
100 mL
Explanation:
The reaction that takes place is:
CaCO₃ + 2HCl → CaCl₂ + H₂O + CO₂First we convert 500 mg of CaCO₃ into mmoles, using its molar mass:
500 mg ÷ 100 mg/mmol = 5 mmol CaCO₃Then we convert 5 mmoles of CaCO₃ into HCl mmoles, using the stoichiometric coefficients of the balanced reaction:
5 mmol CaCO₃ * [tex]\frac{2mmolHCl}{1mmolCaCO_3}[/tex] = 10 mmol HClFinally we calculate the volume of a 0.10 M HCl solution (such as stomach acid) that would contain 10 mmoles:
10 mmol / 0.10 M = 100 mLWhat is the pH of a solution with a 7.8 × 10−13 M hydronium ion concentration?
A) 1.9
B) 2.8
C) 11
D) 12
Answer:
12Explanation:
The pH of a solution can be found by using the formula
[tex]pH = - log [ { H_3O}^{+}][/tex]
From the question we have
[tex]ph = - log(7.8 \times {10}^{ - 13} ) \\ = 12.1079...[/tex]
We have the final answer as
12Hope this helps you
The pH of this solution with a 7.8 × 10⁻¹³ M concentration of hydronium ion is equal to: D. 12.
Given the following data:
Concentration of hydronium ion = 7.8 × 10⁻¹³ M.
What is pH?pH is literally the power of hydrogen ions and it can be defined as a measure of the molar concentration of hydrogen ions in a given solution.
How to calculate the pH of a solution?We would determine the pH of this solution by using this formula;
pH = -log[H⁺]
pH = -log(7.8 × 10⁻¹³).
pH = -(-12.1)
pH = 12.1 ≈ 12.
Read more on pH here: brainly.com/question/24233266
#SJP2
Use the Conductivity interactive to identify each aqueous solution as a strong electrolyte, weak electrolyte, or nonelectrolyte. You are currently in a sorting module. Turn off browse mode or quick nav, Tab to items, Space or Enter to pick up, Tab to move, Space or Enter to drop.
Strong electrolyte Weak electrolyte Nonelectrolyte
NH3 NaCl HCI NaOH C12H22O
Explanation:
strong electrolyte- Nacl HCL NAOH
weak electrolyte- c12H22O, NH3
NaCl,HCl and NaOH are strong electrolytes while ammonia is a weak electrolyte and sucrose is a non-electrolyte.
What are electrolytes?It is a solution which consists of ions which are electrically conducting as a result of movement of ions.Class of electrolytes include most soluble salts,acids and bases which are dissolved in a polar solvent.On dissolution, they separate into the constituent ions.
There are 3 classes according to the nature of substance which results upon dissolution:
1) Strong electrolytes- Substances which on dissolution in a medium dissociate completely are strong electrolytes. eg: NaCl,HCl
2) Weak electrolytes- Substances which on dissolution in a medium dissociate partially are weak electrolytes. eg: NH₃
3)Non-electrolytes- Substances which do not dissociate on dissolution are non-electrolytes. eg: sucrose
Learn more about electrolytes,here:
https://brainly.com/question/8889716
#SPJ2
A recipe calls for 1/4 cup of butter. One ounce (oz) of butter is equivalent to 2 tablespoons (T), and there are 8 oz of butter in 1 cup. Which of the following statements correctly interpret the information provided?
a. The information provided gives the conversion factor 8oz/2T.
b. The information provided gives the conversion factor 8oz/1 cup.
c. The recipe requires 64 T of butter.
d. The recipe requires 4T of butter.
Answer:
D
Explanation:
8oz=1cup
Xoz=1/4cup
cross multiply
Xoz=8×1/4=2
2oz=1/4cup
1oz=2T
2oz=x
cross multiply
×=2×2=4T
The cup of butter, number of tablespoons and ounces of butter are all in direct proportion with one another. The interpretation of the information provided is:
(b). The information provided gives the conversion factor 8oz/1 cup.
Given that:
[tex]1\ recipe = \frac{1}{4}\ cup[/tex]
[tex]1\ oz = 2T[/tex]
[tex]8\ oz = 1\ cup[/tex]
Multiply both sides of [tex]1\ oz = 2T[/tex] by 8
[tex]8 \times 1oz = 8 \times 2T[/tex]
[tex]8 oz = 16T[/tex]
Substitute 8oz for 1 cup in: [tex]1\ recipe = \frac{1}{4}\ cup[/tex]
[tex]1\ recipe = \frac{1}{4} \times 8oz[/tex]
Substitute [tex]8 oz = 16T[/tex]
[tex]1\ recipe = \frac{1}{4} \times 16T[/tex]
[tex]1\ recipe = 4T[/tex]
The interpretations are as follows:
[tex]1\ recipe = 4T[/tex] means that 1 recipe requires 4T of butter [tex]8\ oz = 1\ cup[/tex] means that the information provided gives a conversion of 8oz/1 cupHence, (b) is correct
Read more about direct proportions at:
https://brainly.com/question/1266676
Which of the following colors has the highest energy? O A. Red O B. Green O C. Blue O D. Yellow
Answer:
C. BlueExplanation:
This is because, Blue color highest frequency of energy after Violet and Indigo.
CAN SOMEONE PLEASE HELP ME I WILL MARK YOU AS BRAINLIEST
Explanation:
[tex]2H_2O_2 \rightarrow 2H_2O + O_2[/tex]
First convert the amount of water into moles:
360 g H2O × [tex]\left(\dfrac{1\:\text{mol}H_2O}{18.015\:\text{g}H_2O}\right)[/tex]
[tex] = 20. \:\text{mol}H_2O[/tex]
Now let's calculate the number of moles of O2 gas produced.
20 mol H2O × [tex]\left(\dfrac{1\:\text{mol}O_2}{2\:\text{mol}H_2O}\right)=10\:\text{mol}O_2[/tex]
The volume of gas at 10°C and 5 atm can be found using the ideal gas law:
[tex]PV=nRT[/tex]
[tex]V= \dfrac{nRT}{P}[/tex]
[tex]= \dfrac{(10)(0.082)(283)}{(5)}=46.4\:L[/tex]
When H2S(g) reacts with O2(g) to form H2O(g) and SO2(g), 124 kcal of energy are evolved for each mole of H2S(g) that reacts. Write a balanced equation for the reaction with an energy term in kcal as part of the equation.
Answer:
2H2S(g) + 3O2(g) → 2H2O(g) + 2SO2(g) + 248kcal
Explanation:
The reaction of the problem occurs as follows:
H2S(g) + O2(g) → H2O(g) + SO2(g)
To balance the reaction we must balance oxygens:
H2S(g) + 3O2(g) → 2H2O(g) + 2SO2(g)
To balance the complete reaction:
2H2S(g) + 3O2(g) → 2H2O(g) + 2SO2(g)
As the energy is evolved, 124kcal are as product in the reactio per mole of H2S. As the balanced reaction contains 2 moles of H2S, the heat evolved is:
124kcal*2 = 248kcal:
2H2S(g) + 3O2(g) → 2H2O(g) + 2SO2(g) + 248kcal
And this is the balanced equation
Give the balanced equation for the neutralisation of the excess NaOH with HCI.
1 NaCl + 1 HCl ➡️ 1 NaCl + Water (H2O) .
Explain why the following is an incorrect IUPAC name. 1,3-Dimethylbutane
a. The longest chain is chosen incorrectly.
b. The name of substituent is given incorrectly.
c. The longest chain is numbered incorrectly.
d. Substituents are not listed in alphabetical order.
Answer:
a. The longest chain is chosen incorrectly.
Explanation:
Hello there!
In this case, according to the given information, it turns out possible for us to firstly draw the structural formula of the 1,3-Dimethylbutane:
[tex]CH_3-CH_2-CH(CH3)-CH_2-CH_3[/tex]
Thus, we can see that the correct name should be 3-methylpentane since the longest chain was chosen incorrectly, as it must have five carbon atoms.
Regards!
Which of the following is a protein source of plant origin
Answer:
soy....plant protein also is found in vegtables and grain products.
The protein that is derived from the plant is soyabean. Protein-rich foods have a rich source of amino acids. Amino acids are required by the body for different cellular activities.
What are proteins?
Proteins are present in plant-based foods and animal-based foods. In nature, the plant-based foods that are rich in proteins are soybeans, beans etc. Animal products such as dairy products, milk, and cheese are rich sources of proteins.
Animal-based foods such as eggs, meat, and fish have a good amount of protein. The proteins are made up of amino acids. Peptide bonds connect each amino acid to the next.
Proteins are necessary for the body, as cells need amino acids for both structural and functional support. Not all cells of the body synthesise all amino acids. Some essential amino acids are required by the body and can be taken from external sources such as plants.
Hence, the plant-based protein is soyabean.
To learn more about the protein, here
https://brainly.com/question/17095120
#SPJ2.
The question is incomplete; the complete question may be the following:
1) Which of the following is a protein source of plant origin?
A)egg
B) Soyabean
C)cheese
D)Milk
Andy needs to determine the freezing point depression of 30.0 mL of 0.50 m AlCl3 aqueous solution. When dissolved, AlCl3 dissociates into Al3 and Cl-. Andy realizes that he may need to reduce the effect of ion-pairing in his 0.50 m AlCl3 aqueous solution. Which of the following would reduce the ion-pairing effect in his AlCl3 solution?A. Add some solid AICIz to his solution.B. Add some water to his solution.C. Use only half of his initial volume.D. Use 45 mL of the 0.50 m AlCl3 solution.
Answer:
Add some water to his solution
Explanation:
Ion pair effect refers to strong electrostatic interaction between oppositely charged ions in solution. Such strong interaction affects solute- solvent interaction when an ionic substance is dissolved in water.
High solute concentration may lead to ion-pair effect. Hence, the ion pair effect may be minimized by adding more water (decreasing the concentration of the solution).
To reduce the ion- pair effect, Andy needs to add some water to his solution (dilution).
The activity that would reduce the ion-pairing effect in his AICI₃ solution is : ( B ) add some water to his solution
Ion pair effectIon pair effect is a strong electrostatic interaction seen between ions with opposite charges, when an ionic substance is been dissolved in a solvent such as water this effect will affect the dissolution of the substance.
High concentration of the solute in a solution also leads to the ion pair effect therefore for Andy to reduce the ion-pairing effect in his solution he has to add more water to reduce the concentration of the solute.
Hence we can conclude that The activity that would reduce the ion-pairing effect in his AICI₃ solution is to add some water to his solution
Learn more about ion pair effect : https://brainly.com/question/24100697
What mass of hydrochloric acid that reacted with zinc will produced 0.15dm3 of hydrogen at st.p? Equation for this reaction:
Zn + 2HCl ------> ZnCl2 + H2
Answer:
[tex]{ \tt{22.4 \: dm {}^{3} \: contains \: 1 \: mole \: of \: hydrogen }} \\ { \tt{0.15 \: {dm}^{3} \: will \: contain \: ( \frac{0.15}{22.4} \times 1) \: moles }} \\ = 0.0067 \: moles \\ { \bf{mole \: ratio = 1 :1 }} \\ { \tt{1 \: mole \: weighs \: 65.38 \: g}} \\ { \tt{0.0067 \: moles \: weighs \: (0.0067 \times 65.38) \: g}} \\ = 0.44 \: g[/tex]
convert 12nanometer to centimeter
Answer:
1x10^-6
Explanation:
What is the IUPAC name for this organic molecule?
Answer:
2–methylbutane
Explanation:
To name the compound given above, the following must be obtained:
1. Determine the longest continuous carbon chain. This gives the parent name of the compound.
2. Determine the substituent group attached.
3. Determine the position of the substituent group by giving it the lowest possible count..
4. Combine the above to obtain the name of the compound.
With the above information, we can name the compound as follow:
1. The longest continuous carbon chain of the compound is 4. Thus, the parent name is butane.
2. The substituent group attached to the compound is methyl (–CH₃).
3. The methyl (–CH₃) group is located at carbon 2 (i.e counting from the left side).
4. The name of the compound is:
2–methylbutane
A student is adding DI water to a volumetric flask to make a 50% solution. Unfortunately, he was not paying attention and filled the flask past the calibration mark. Instead of starting over, the student decides to continue with the experiment. How will the student's results be affected by his mistakes
Answer:
His results will be skewed because there was more water than stock solution. Which would cause the percentage solution to be less than 50% therefore the density would be less than the actual value.
Explanation:
The solution will have percentage less than that of 50%. Therefore the density would be less than the actual value.
Suppose there should be 50 mL of the solution, and he added 60 mL. So 10 mL of the solution is added more.
Suppose the mass of the solute is m.
Originally, the density is = [tex]$\frac{m}{50}$[/tex] [tex]\left(\frac{\text{mass}}{\text{volume}}\right)[/tex]
Now after adding extra 10 mL , the density becomes [tex]$\frac{m}{60}$[/tex].
Therefore, [tex]$\frac{m}{50}>\frac{m}{60}$[/tex]
So the density decreases when we add more solution.
I am holding a balloon containing 439 mL of gas over my fireplace. The temperature and pressure of the gas inside the balloon is 317.15 K and 0.959 atm, respectively. Suppose I don't want the pressure to change, but I want to the volume to go down to 0.378 L. What is the temperature that I need to reach when I cool down the balloon?
To what temperature (in Celsius) must the balloon be cooled to reduce its volume to 0.378 L if the pressure doesn't change (remained constant)?
Answer:
-0.08 °C
Explanation:
We can solve this problem by using Charles' law, which states that at constant pressure:
V₁T₂ = V₂T₁Where in this case:
V₁ = 439 mLT₂ = ?V₂ = 0.378 L ⇒ 0.378 * 1000 = 378 mLT₁ = 317.15 KWe input the data:
439 mL * T₂ = 378 mL * 317.15 KAnd solve for T₂:
T₂ = 273.08 KFinally we convert 273.08 K to Celsius:
273.08 K - 273.16 = -0.08 °CWhich of these increases the friction of someone walking on the floor?
Answer:
.This is because gravity pulls down harder on the heavier one, which increases its friction with the floor
Mark me as Branliest
Anew fictitious element was discovered. It is a metal named jolmium, J,and it has three valence electrons. If it combineswith iodine it forms jolmium iodide. Answer the following questions.a.Is this compound ionic or covalent
a. Is this compound ionic or covalent?
b. What is the formula of Jolmium iodide?
c. What is the charge on the metal J in this compound?
d. Explain how you know that is the charge?
Answer:
A new fictitious element was discovered.
It is a metal named jolmium, J, and it has three valence electrons.
If it combines with iodine it forms jolmium iodide. Answer the following questions.
a.Is this compound ionic or covalent
b. What is the formula of Jolmium iodide?
c. What is the charge on the metal J in this compound?
d. Explain how you know that is the charge?
Explanation:
It is given the element jolmium J is a metal with three valence electrons.
Since metals are highly electropositive, they lose electrons easily and form cations (Ions with a positive charge).
[tex]J^{3+}[/tex] ion will be formed.
b) The formula of jolmium iodide is shown below:
[tex]J^{+3} I^{-1}\\The formula becomes:\\JI_{3}[/tex]
a) The compound is ionic in nature.
Since the compound formed between a metal atom and a nonmetal atom will take place by transfer of electrons.
Hence, it is ionic in nature.
c) The charge on the metal J in this compound is +3.
d) Given J has three valence electrons.
That means it can lose three electrons to form a bond.
So, its valency is three.
Toothpastes containing sodium hydrogen carbonate (sodium bicarbonate) and hydrogen peroxide are widely used. Write Lewis structures for the hydrogen carbonate ion and hydrogen peroxide molecule, with resonance forms where appropriate.
Answer:
See explanation and images attached
Explanation:
The first image shows the structure of hydrogen peroxide. It does not exist as resonance structures. The structure and properties of the molecule can wholly be explained on the basis of a single Lewis structure.
However, the structure of the bicarbonate ion in sodium bicarbonate can not be completely described by a single Lewis structure. Hence, two resonance structures are shown for the bicarbonate ion. In each case, Na^+ is the counter ion.
Write briefly on carbohydrates
Answer:
carbohydrates are simple sugars which can be broken down to form 3 sugars.
which are , (maltose) (fructose) & (glucose)
According to the equation 2K(s) + CI2(g) 2kCI(s), potassium reacts with chlorine to form potassium chlorine. If 100 atoms of potassium react with chlorine gas, how many chlorine molecules will be needed to completely react?
Answer:
50 CI₂ molecules
Explanation:
2K(s) + CI₂(g) → 2KCI(s)By looking at the stoichiometric coefficients, we can tell that if 2 atoms of potassium (K) react with chlorine gas (CI₂), 1 chlorine molecule would react.
With that in mind we can calculate how many CI₂ molecules would react with 100 K atoms:
100 atoms K *[tex]\frac{1Cl_2Molecule}{2KAtom}[/tex] = 50 CI₂ molecules