Define wave length as applied to wave motion​

Answers

Answer 1

Answer: Wavelength can be defined as the distance between two successive crests or troughs of a wave. It is measured in the direction of the wave.

Explanation:

Wavelength refers to the length or distance between two identical points of neighboring cycles of a wave signal traveling in space or in any physical medium. ... The wavelength of a signal is inversely proportional to its frequency, that is, the higher the frequency, the shorter the wavelength.


Related Questions

What is the need for satellite communication elaborate

Answers

The high frequency radio waves used for telecommunications links travel by line of sight and so are obstructed by the curve of the Earth. The purpose of communications satellites is to relay the signal around the curve of the Earth allowing communication between widely separated geographical points.

Explanation:

hope it helps!!

A regulation soccer field for international play is a rectangle with a length between 100 m and a width between 64 m and 75 m. What are the smallest and largest areas that the field could be?

Answers

Answer:

The smallest and largest areas could be 6400 m and 7500 m, respectively.

Explanation:

The area of a rectangle is given by:

[tex] A = l*w [/tex]

Where:

l: is the length = 100 m

w: is the width

We can calculate the smallest area with the lower value of the width.

[tex] A_{s} = 100 m*64 m = 6400 m^{2} [/tex]                            

And the largest area is:

[tex] A_{l} = 100 m*75 m = 7500 m^{2} [/tex]  

Therefore, the smallest and largest areas could be 6400 m and 7500 m, respectively.            

I hope it helps you!                        

Answer:

the largest areas that the field could be is [tex]A_l[/tex]=7587.75 m

the smallest areas that the field could be is [tex]A_s[/tex]=6318.25 m

Explanation:

to the find the largest and the smallest area of the field measurement error is to be considered.

we have to find the greatest possible error, since the measurement was made nearest whole mile, the greatest possible error is half of 1 mile and that is 0.5m.

therefore to find the largest possible area we add the error in the mix of the formular for finding the perimeter with the largest width as shown below:

[tex]A_l[/tex]= (L+0.5)(W+0.5)

(100+0.5)(75+0.5) = (100.5)(75.5) = 7587.75 m

To find the smallest length we will have to subtract instead of adding the error factor value of 0.5 as shown below:

[tex]A_s[/tex]= (L-0.5)(W-0.5)

(100-0.5)(64-0.5) = (99.5)(63.5) = 6318.25 m

how will be electric lines of force where intensity of electric field is maximum ?
a. wider
b. +ve to -ve
c. narrow
d. -ve to +ve

Answers

i'm pretty sure the answer is A wider

Electric lines of force where intensity of electric field is maximum when its wider.

What is Electric field?

The physical field that surrounds electrically charged particles and exerts force on all other charged particles in the field, either attracting or repelling them, is known as an electric field (also known as an E-field. It can also refer to a system of charged particles' physical field.

Electric charges and time-varying electric currents are the building blocks of electric fields. The electromagnetic field, one of the four fundamental interactions (also known as forces) of nature, manifests itself in both electric and magnetic fields.

Electrical technology makes use of electric fields, which are significant in many branches of physics. For instance, in atomic physics and chemistry, the electric field acts as an attracting force to hold atoms' atomic nuclei and electrons together.

Therefore, Electric lines of force where intensity of electric field is maximum when its wider.

To learn more about electric field, refer to the link:

https://brainly.com/question/1443103

#SPJ2

Cho dòng điện xoay chiều trong sản xuất và sinh hoạt ở nước ta có tần số f = 50Hz. Tính chu kỳ T và tần số góc ω?

Answers

Answer:

T = 1/f = 1/50(s)

ω = 2πf = 100π (rad/s)

(vote 5 sao nhó :3 )

I need help with this please!!!!

Answers

Answer:

1.84 hours

I hope it's helps you

Steel railway tracks are laid at 8oC. What size of expansion gap are needed 10m long rail sections if the ambient temperature varies from -10oC to 50oC? [Linear expansivity of steel = 12 x]​

Answers

Answer:

Gap left = Change in length on heating

Gap=Initial length×Coefficient of linear expansion×change in temperature

Gap=10×0.000012×15m

⟹Gap=0.0018 m

this is an example u have to put your equation in it

state the laws of reflection​

Answers

Answer:

Explanation:

The law of reflection says that the reflected angle (measured from a vertical line to the surface  called the normal) is equal to the reflected angle measured from the same normal line.

All other properties of reflection flow from this one statement.

A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses (velocity = 0) for a fraction of a second at the very top before heading down the other side.

a) Draw a sankey diagram for a roller coaster's climb.

Answers

A roller coaster uses 800 000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy and pauses for a fraction of a second at the very top before heading down the other side. At the top of the hill total, the kinetic energy of the roller coaster would be zero as the velocity is zero at the top of the hill, therefore the total mechanical energy is only because of potential energy.

What is mechanical energy?

Mechanical energy is the combination of all the energy in motion represented by total kinetic energy and the total stored energy in the system which is represented by total potential energy.

The expression for total mechanical energy is as follows

ME= KE+PE

As total mechanical energy is the sum of all the kinetic as well as potential energy stored in the system.As given in the problem a roller coaster uses 800000 J of energy to get to the top of the first hill. During this climb, it gains 500 000 J of potential energy which means 300000 J of energy is lost in the frictional energy while climbing the hill,

Thus at the top of the hill, the total energy of the roller coasters is only due to the potential energy.

Learn more about mechanical energy from here brainly.com/question/12319302

#SPJ2

The position of a particle is given by ~r(t) = (3.0 t2 ˆi + 5.0 ˆj j 6.0 t kˆ) m

Answers

Answer:

[tex]v=(6ti+6k)\ m/s[/tex]

Explanation:

Given that,

The position of a particle is given by :

[tex]r(t) = (3.0 t^2 i + 5.0j+ 6.0 tk) m[/tex]

Let us assume we need to find its velocity.

We know that,

[tex]v=\dfrac{dr}{dt}\\\\=\dfrac{d}{dt}(3.0 t^2 i + 5.0j+ 6.0 tk) \\\\=(6ti+6k)\ m/s[/tex]

So, the velocity of the particle is [tex](6ti+6k)\ m/s[/tex].

Express 6revolutions to radians

Answers

Answer:

About 37.70 radians.

Explanation:

1 revolution = 2[tex]\pi[/tex] radians

∴ 6 revolutions = (6)(2[tex]\pi[/tex] radians)

6 revolutions = 37.6991 or ≈ 37.70 radians

Electrons are emitted from a surface when light of wavelength 500 nm is shone on the surface but electrons are not emitted for longer wavelengths of light. The work function of the surface is

Answers

Explanation:

Given: [tex]\lambda = 500\:\text{nm} = 5×10^{-7}\:\text{m}[/tex]

[tex]\nu = \dfrac{c}{\lambda} = \dfrac{3×10^8\:\text{m/s}}{5×10^{-7}\:\text{m}}[/tex]

[tex]\:\:\:\:\:= 6×10^{14}\:\text{Hz}[/tex]

The work function [tex]\phi[/tex] is then

[tex]\phi = h\nu = (6.626×10^{-34}\:\text{J-s})(6×10^{14}\:\text{Hz})[/tex]

[tex]\:\:\:\:\:\:\:= 3.98×10^{-19}\:\text{J}[/tex]

The work function of the surface is equal to 3.98 × 10⁻¹⁹J.

What are frequency and wavelength?

The frequency can be explained as the number of oscillations of a wave in one second. The frequency has S.I. units of hertz.

The wavelength can be explained as the distance between the two adjacent points such as two crests or troughs on a wave.

The expression between wavelength (λ), frequency, and speed of light (c) is:

c = νλ

Given, the wavelength of the light, ν = 500 nm

The frequency of the light can determine from the above-mentioned relationship:

ν = c/λ= 3 × 10⁸/500 × 10⁻⁹ = 6 × 10¹⁴ Hz

The work function = h ν =  6 × 10¹⁴ × 6.626 × 10⁻³⁴

φ = 3.98 × 10⁻¹⁹J

Therefore, the work function of the surface is 3.98 × 10⁻¹⁹J.

Learn more about wavelength and frequency, here:

brainly.com/question/18651058

#SPJ2

A car is driving towards an intersection when the light turns red. The brakes apply a constant force of 1,398 newtons to bring the car to a complete stop in 25 meters. If the weight of the car is 4,729 newtons, how fast was the car going initially

Answers

Answer:

the initial velocity of the car is 12.04 m/s

Explanation:

Given;

force applied by the break, f = 1,398 N

distance moved by the car before stopping, d = 25 m

weight of the car, W = 4,729 N

The mass of the car is calculated as;

W = mg

m = W/g

m = (4,729) / (9.81)

m = 482.06 kg

The deceleration of the car when the force was applied;

-F = ma

a = -F/m

a = -1,398 / 482.06

a = -2.9 m/s²

The initial velocity of the car is calculated as;

v² = u² + 2ad

where;

v is the final velocity of the car at the point it stops = 0

u is the initial velocity of the car before the break was applied

0 = u² + 2(-a)d

0 = u² - 2ad

u² = 2ad

u = √2ad

u = √(2 x 2.9 x 25)

u =√(145)

u = 12.04 m/s

Therefore, the initial velocity of the car is 12.04 m/s

What Are the type's of Tidal turbines?

Answers

Answer:

Types of tidal turbines

Axial turbines.

Crossflow turbines.

Flow augmented turbines.

Oscillating devices.

Venturi effect.

Tidal kite turbines.

Turbine power.

Resource assessment.

Answer:

Axial turbines

Crossflow turbines

flow augmented turbines

Convert 385k to temperature of

Answers

Answer:

233.33°F

Explanation:

(385K - 273.15) * 9/5 + 32 = 233.33°F

Si un resorte de constante elástica 1300 n/m se comprime 12 cm ¿Cuanta energía almacena? Y si estira 12cm ¿Cuanta energía almacena?

Answers

La energía que almacena el resorte cuando se comprime y estira 12 cm es 9,4 J.  

La energía potencial elástica del resorte se puede calcular con la siguiente ecuación:

[tex] E_{p} = \frac{1}{2}kx^{2} [/tex]

En donde:

k: es la constante del resorte = 1300 N/m

x: es la distancia de compresión o de elongación = 12 cm = 0,12 m

Dado que la energía es proporcional al cuadrado de la distancia recorrida por el resorte (x), la energía almacenada por el resorte durante la compresión será la misma que la energía almacenada por la elongación.

Por lo tanto, la energía almacenada es:

[tex]E_{p} = \frac{1}{2}kx^{2} = \frac{1}{2}1300 N/m*(0,12 m)^{2} = 9,4 J[/tex]                                                            

Entonces, la energía del resorte cuando se comprime y cuando se estira es la misma, a saber 9,4 J.                

Para saber más sobre energía potencial visita este link: https://brainly.com/question/156316?referrer=searchResults

Espero que te sea de utilidad!

Answer:

Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.

Explanation:

La Energía Potencial Elástica almacenada por el resorte ([tex]U_{e}[/tex]), en joules, se calcula a partir de la Ley de Hooke, la definición de Trabajo y el Teorema del Trabajo y la Energía, cuya expresión se presenta abajo:

[tex]U_{e} = \frac{1}{2}\cdot k\cdot (x_{f}^{2}-x_{o}^{2})[/tex] (1)

Donde:

[tex]k[/tex] - Constante elástica del resorte, en newtons por metro.

[tex]x_{o}[/tex] - Posición inicial del resorte, en metros.

[tex]x_{f}[/tex] - Posición final del resorte, en metros.

Nótese que el resorte sin deformar tiene una posición de cero, la tensión tiene un valor positivo y la compresión, negativo.

Asumiendo que en ambos casos el resorte se encuentra inicialmente sin deformar, se reduce (1) a una forma de función par, es decir, una función que cumple con la propiedad de que [tex]f(x) = f(-x)[/tex], se encuentra que al comprimirse o estirarse en la misma medida almacena la misma cantidad de energía.

La cantidad de energía a almacenar es:

[tex]U_{e} = \frac{1}{2}\cdot \left(1300\,\frac{N}{m} \right)\cdot (0,12\,m)^{2}[/tex]

[tex]U_{e} = 9,360\,J[/tex]

Al comprimirse o estirarse 12 centímetros desde su posición sin deformar, el resorte almacena 9,360 joules.

When you shine a beam of light, which is composed of just two different colors, red and green, onto a diffraction grating which color gets diffracted more

Answers

Answer:

The diffraction grating separates light into colors as the light passes through the many fine slits of the grating. This is a transmission grating. ... The prism separates light into colors because each color passes through the prism at a different speed and angle.

A spherically mirrored ball is slowly lowered at New Years Eve as midnight approaches. The ball has a diameter of 8.0 ft. Assume you are standing directly beneath it and looking up at the ball. When your reflection is half your size then the mirror is _______ ft above you.

Answers

Answer:

The distance between mirror and you is 2 ft.

Explanation:

diameter, d = 8 ft

radius of curvature, R = 4 ft

magnification, m = 0.5

focal length, f = R/2 = 4/2 = 2 ft

let the distance of object is u and the distance of image is v.

[tex]\frac{1}{f}=\frac{1}{v}+\frac{1}{u}\\\\\frac{1}{2}=\frac{1}{v}+\frac{1}{u}\\\\v = \frac {2 u}{u - 2}[/tex]

Use the formula of magnification

[tex]m = \frac{v}{u}\\\\0.5 =\frac { u}{u - 2}\\ \\u - 2 = 2 u \\\\u = -2 ft[/tex]

Flapping flight is very energy intensive. A wind tunnel test
on an 89 g starling showed that the bird used 12 W of
metabolic power to fly at 11 m/s. What is its metabolic power for starting flight?

Answers

Answer:

The metabolic power for starting flight=134.8W/kg

Explanation:

We are given that

Mass of starling, m=89 g=89/1000=0.089 kg

1 kg=1000 g

Power, P=12 W

Speed, v=11 m/s

We have to find the metabolic power for starting flight.

We know that

Metabolic power for starting flight=[tex]\frac{P}{m}[/tex]

Using the formula

Metabolic power for starting flight=[tex]\frac{12}{0.089}[/tex]

Metabolic power for starting flight=134.8W/kg

Hence, the metabolic power for starting flight=134.8W/kg

Question 5 of 10
What must be the same for two resistors that are connected in parallel?

Answers

Answer:

in parallel combination : potential difference between two terminal of resistors are always constant. ... hence, potential difference ( voltage ) must be same across each resistor .

Explanation:

A 15.0 g bullet traveling horizontally at 865 m>s passes through a tank containing 13.5 kg of water and emerges with a speed of 534 m>s. What is the maximum temperature increase that the water could have as a result of this event

Answers

Answer:

The rise in temperature is 0.06 K.

Explanation:

mass of bullet, m = 15 g

initial speed, u = 865 m/s

final speed, v = 534 m/s

mass of water, M = 13.5 kg

specific heat of water, c = 4200 J/kg K

The change in kinetic energy

[tex]K = 0.5 m(u^2 - v^2)\\\\K = 0.5\times 0.015\times (865^2-534^2)\\\\K = 3473 J[/tex]

According to the conservation of energy, the change in kinetic energy is used to heat the water.

K = m c T

where, T is the rise in temperature.

3473 = 13.5 x 4200 x T

T = 0.06 K

what Is accuracy ............​

Answers

Answer:

Accuracy is how much the consequence of an estimation adjusts to the right worth or a norm' and basically alludes to how close an estimation is to its concurred esteem

《OAmalaOHopeO》

Answer:

In a set of measurements, accuracy is closeness of the measurements to a specific value, while precision is the closeness of the measurements to each other.

Explanation:

_Hope it helps you_

3. A microscope is focused on a black dot. When a 1.30 cm -thick piece of plastic is placed over the dot, the microscope objective has to be raised 0.410 cm to bring the dot back into focus. What is the index of refraction of the plastic

Answers

The index of refraction of the plastic is approximately 1.461

The known values in the question are;

The thickness of the piece of plastic placed on the dot = 1.30 cm

The height to which the microscope objective is raised to bring the dot back to focus = 0.410 cm

The unknown values in the question are;

The index of refraction

Strategy;

Calculate the refractive index by making use of the apparent height and real height method for the black dot under the thick piece of plastic

[tex]\mathbf{ Refractive \ index, n = \dfrac{Real \ depth}{Apparent \ depth}}[/tex]

The real depth of the dot below the piece of plastic, d₁ = 1.30 cm

The apparent depth of the dot, d₂ = The actual depth - The height to which the microscope is raised

Therefore;

The apparent depth of the dot, d₂ = 1.30 cm - 0.410 cm = 0.89 cm

[tex]The \ refractive \ index, \ n = \dfrac{d_1}{d_2}[/tex]

Therefore, n = 1.30/0.89 ≈ 1.461

The refractive index of the plastic block, n ≈ 1.461

Learn more about refractive index of light here;

https://brainly.com/question/24321580

What is not one of the main uses of springs?
A. Car suspension
B. Bike suspension
C. The seasons
D. Clock making

Answers

Hi! I believe the answer is C. or The seasons because all the other options use springs when making cars, bikes, and clocks. I hope this helped. Goodluck :)

How do you know that a liquid exerts pressure?​

Answers

Answer:

The pressure of water progressively increases as the depth of the water increases. The pressure increases as the depth of a point in a liquid increases. The walls of the vessel in which liquids are held are likewise subjected to pressure. The sideways pressure exerted by liquids increases as the liquid depth increases.

which characteristic of nuclear fission makes it hazardous?

Answers

Answer:The radioactive waste

Explanation:Fission is the splitting of a heavy unstable nucleus into two Lighter nuclei

Parallel Wires: Two long, parallel wires carry currents of different magnitudes. If the current in one of the wires is doubled and the current in the other wire is halved, what happens to the magnitude of the magnetic force that each wire exerts on the other?

Answers

Answer:

Explanation:

Given force between 2 currents carrying

wires = F₀

Magnetic force between the2 wires =F₀= (μ₀/4π) x ( 2 (μ₀/4π) x ( 2I₁I₂ / μ) x L

where I₁=Current in wire 1

           I₂= Current in wire 2

           L= Length of the wire

when one current is doubled and the other is halved

I₁= 2 I₁

I₂=    I₂/2

F₀ = (μ₀/4π) x ( 2× (2I₁) (I₂/2) / μ) x L

A ball is launched from the ground with a horizontal speed of 30 m/s and a vertical speed of 30 m/s. How far horizontally will it travel in 2 seconds?
A. 30 m
B. 90 m
C. 45 m
D. 60 m

Answers

Answer:

It will travel Vx * t = 30 m/s * 2 s = 60 m

Distance = velocity x time
= 30m/s x 2 sec
= 60 m/s

A sinewave has a period (duration of one cycle) of 645 μs (microseconds). What is the corresponding frequency of this sinewave, in kHz

Answers

The corresponding frequency of this sinewave, in kHz, expressed to 3 significant figures is: 155 kHz.

Given the following data:

Period = 645 μs

Note: μs represents microseconds.

Conversion:

1 μs = [tex]1[/tex] × [tex]10^-6[/tex] seconds

645 μs = [tex]645[/tex] × [tex]10^-6[/tex] seconds

To find corresponding frequency of this sinewave, in kHz;

Mathematically, the frequency of a waveform is calculated by using the formula;

[tex]Frequency = \frac{1}{Period}[/tex]

Substituting the value into the formula, we have;

[tex]Frequency = \frac{1}{645 * 10^-6}[/tex]

Frequency = 1550.39 Hz

Next, we would convert the value of frequency in hertz (Hz) to Kilohertz (kHz);

Conversion:

1 hertz = 0.001 kilohertz

1550.39 hertz = X kilohertz

Cross-multiplying, we have;

X = [tex]0.001[/tex] × [tex]1550.39[/tex]

X = 155039 kHz

To 3 significant figures;

Frequency = 155 kHz

Therefore, the corresponding frequency of this sinewave, in kHz is 155.

Find more information: brainly.com/question/23460034

As the speed of a particle approaches the speed of light, the momentum of the particle Group of answer choices approaches zero. decreases. approaches infinity. remains the same. increases.

Answers

Answer:

approaches infinity

Explanation:

There are two momentums, the classical momentum which is equal to the product of mass and velocity, and the relativistic momentum, the one we should look at when we work with high speeds, and this happens because massive objects have a speed limit, in this case, we are approaching the speed of light, so we need to work with the relativistic momentum instead of the classical momentum.

The relativistic momentum can be written as:

[tex]p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]

where

u = speed of the object relative to the observer, in this case we have that u tends to c, the speed of light.

m = mass of the object

c = speed of light.

So, as u tends to c, we will have:

[tex]\lim_{u \to c} p = \frac{1}{\sqrt{1 - \frac{u^2}{c^2} } } *m*u[/tex]

Notice that when u tends to c, the denominator on the first term tends to zero, thus, the relativistic momentum of the object will tend to infinity.

Then the correct option is infinity, as the particle speed approaches the speed of light, the relativistic momentum of the particle tends to infinity.

If a boy lifts a mass of 6kg to a height of 10m and travels horizontally with a constant velocity of 4.2m/s, calculate the work done? Explain your answer.

Answers

Answer:

W = 641.52 J

Explanation:

The work done here will be the sum of potential energy and the kinetic energy of the boy. Here potential energy accounts for vertical motion part while the kinetic energy accounts for the horizontal motion part:

[tex]Work\ Done = Kinetic\ Energy + Potential\ Energy\\\\W = K.E +P.E\\\\W = \frac{1}{2}mv^2+mgh\\\\[/tex]

where,

W = Work Done = ?

m = mass = 6 kg

v = speed = 4.2 m/s

g = acceleration dueto gravity = 9.81 m/s²

h = height = 10 m

Therefore,

[tex]W = \frac{1}{2}(6\ kg)(4.2\ m/s)^2+(6\ kg)(9.81\ m/s^2)(10\ m)[/tex]

W = 52.92 J + 588.6 J

W = 641.52 J

Other Questions
Invisible damage to the body resulting from repeating a movement often is a Find an equation of the plane orthogonal to the line(x,y,z)=(0,9,6)+t(7,7,6)which passes through the point (9, 6, 0).Give your answer in the form ax+by+cz=d (with a=7). You cannot be at the railway station when your father arrives there. Your friend is going to help you to pick him up. Write an email in about 50-80 words to your friend. You should say:- when your father will arrive;- what he looks like;- what he will be wearing. black pencils cost 75 naira each and colour pencils cost 105 naira each if 24 mixed pencils cost 2010 naira how many of them were black hint let there be x black pencils thus there are (24-x) coloured pencils. What diagram shows causes and one effect using arrows? A plebeian and a patrician are both observed committing the same crime.How would they end up being treated by Roman law. 2( 5 1 m 5 2 )+ 5 3 2, left parenthesis, start fraction, 1, divided by, 5, end fraction, m, minus, start fraction, 2, divided by, 5, end fraction, right parenthesis, plus, start fraction, 3, divided by, 5, end fraction explain how typical cells are adapted to their function 11. The student government is selling flowers for homecoming. The project costs them $20 for advertising and$3 for each flower sold.a. Evaluate the expressions 3n+20 and 3(n+20) when n = 4.b. Which expression shows their total cost? How do you know? While giving discharge instructions to a patient who will be taking cholestyramine [Questran], the nurse wants to assess the patient's understanding of the treatment. Which statement made by the patient best demonstrates a need for additional teaching State if the scenario involves a permutation or a combination. Then find the number of possibilities.A team of 15 basketball players needs to choose two players to refill the water cooler.Permutation/Combination: Answer: which of the following illustrates commutative property of addition? 17+4=4+17 Reason Can you subtract a positive integer from a positive integerand get a negive result? Explain your answer. 2. Slime moulds cannot be put neither in kingdom Plantae nor in kingdom Animalia. Give reason.3. Give the disadvantages of the two kingdom classification. Which systems of inequality's does this graph represent How do characters and conflicts work together Unscramble the following words and spell them correctly (all of these words come from this lesson):opalesbalaoteficanpurnocnipaejoalrtaesleovuh please answer this!! Please multiply 6c(4) Cost of Goods Sold, Cost of Goods Manufactured Glenville Company has the following information for April: Cost of direct materials used in production $41,000 Direct labor 47,000 Factory overhead 20,000 Work in process inventory, April 1 34,000 Work in process inventory, April 30 27,000 Finished goods inventory, April 1 24,000 Finished goods inventory, April 30 18,000 a. For April, determine the cost of goods manufactured. Using the data given, prepare a statement of Cost of Goods Manufactured. b. For April, determine the cost of goods sold. Using the data given, prepare a statement of Cost of Goods Sold.