An object is 29cm away from a concave mirror's surface along the principal axis.If the mirror's focal length is 9.50 cm, how far away is thecorresponding image?
a.12
b.14
c.29
d.36

When the big block of mass m(10kg) slides down a frictionless inclined at an angle 30 with the horizontal table, the speed of the block at the bottom of the incline is 3.14 m/s.

Given that

Mass of the block, m = 10 kg.

Angle of inclination, θ = 30°

Initial velocity, u = 0.

Frictional force, f = 0.

Using the formula for gravitational force, F = mg

where, g = 9.8 m/s² (acceleration due to gravity)

F = mg= 10 kg × 9.8 m/s²= 98 N

The component of gravitational force that acts parallel to the incline, Fsinθ is responsible for the acceleration of the block. Fsinθ = ma; Where a is the acceleration of the block.

a= (98 N)sin 30° / 10 kg= 4.9 m/s²

Using the formula for speed, v = u + at where,

u = initial velocity = 0m/s

t = time taken = time taken to slide from top to bottom of the incline.= √(2h/g) where,

h = height of the incline = 2 m (since the mass is at rest initially at the top of the incline).

Therefore, t = √(2 × 2 m / 9.8 m/s²)= 0.64 s

Substituting the values in the above formula, v = u + at= 0 + (4.9 m/s² × 0.64 s)= 3.14 m/s.

To know more about speed, refer here:

https://brainly.com/question/29309579#

SPJ11#

A bar magnet falls under the influence of gravity along the axis of a long copper tube. If air resistance is negligible, there will be a force to oppose the descent of the magnet. The magnet will reach a terminal velocity. Here's why:

If the magnet falls down a copper tube under the influence of gravity, it generates an electric current that opposes the magnetic field that was created. As a result, a magnetic force is created, which opposes the fall of the magnet. As a result, there is a force opposing the descent of the magnet.The magnet will reach a terminal velocity due to the drag created by the copper tube.

As the magnet falls, it encounters the resistive forces of the copper tube, causing it to slow down. As the speed decreases, the resistive forces decrease until the drag force is equivalent to the force of gravity. The magnet then reaches a steady state called the terminal velocity. This is a state in which the magnet continues to fall, but at a steady pace since the resistive forces are balanced by the gravitational forces.

Learn more about magnetic force: https://brainly.com/question/29252577

#SPJ11

The structure described by the scientist, which is an oily sphere with an inner fluid, is most likely a lipid vesicle.

Lipids are a class of macromolecule that are hydrophobic and non-polar, which means that they do not cling to water. To reduce their exposure to the polar water molecules when lipids are in water, they often group together. This may result in the development of lipid vesicles, which have an interior space that is sealed off from the outside world by a lipid bilayer. Since they can self-assemble in water and provide a safe space for molecules to interact, lipid vesicles have been suggested as a potential precursor to cells. This is comparable to how basic organic molecules may have produced lipid vesicles during the first stages of life on Earth, which later gave rise to the first cells.

Learn more about  scientist here:

https://brainly.com/question/17450573

#SPJ4

Нам не дано коэффициент трения, значит, можно не учесть силу трения. От этого, по второму закону Ньютона, F=ma=5×20=100 Н.

И это всё!

There are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm.

To calculate the number of electrons in a 30.0 cm length of 12-gauge copper wire (diameter 2.05 mm), you can use the following equation:

n = ρV / m

where:

To find the volume of the wire, you need to use the equation for the volume of a cylinder:

Where:

Therefore, V = π(1.025 mm)²(30.0 cm) = 9.30 cm³The mass of one copper atom is 63.55 g/mol or 1.054 x 10⁻²² g. To find m, you need to use Avogadro's number (6.02 x 10^23 atoms/mol):m = (63.55 g/mol) / (6.02 x 10^23 atoms/mol) = 1.055 x 10⁻²² g

Now, you can plug in the values:

n = (8.96 g/cm³)(9.30 cm³) / (1.055 x 10⁻²² g) = 7.86 x 10²³ electrons

Therefore, there are 7.86 x 10²³ electrons in a 30.0 cm length of 12-gauge copper wire with a diameter of 2.05 mm. This should be rounded to 2 significant figures, so the final answer is 7.9 x 10²³ electrons.

Learn more about electrons: https://brainly.com/question/26084288

#SPJ11

Answer: 7.17

Explanation:

Maximum height reached by Kangaroo H=2.62

Final velocity at the maximum height v=0

Acceleration due to gravity   g=−9.8 m/s2    

Using   v2−u2=2gH∴   0−u2=2(−9.8)(2.62)

⟹ u=2(9.8)(2.62)​=7.17 m/s

The space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

Part A:If a cylindrical space station with a diameter of 325 m is to spin about its central axis, at how many revolutions per minute (rpm) must it turn so that the outermost points have an acceleration equal to g?The acceleration of the outermost points is given as g. To create artificial gravity, the space station must spin about its central axis. To determine the required rpm, use the formula for acceleration due to centripetal force, which is given by:a = rω2Where, a is the acceleration due to centripetal force, r is the radius of the circle, and ω is the angular velocity of the object in radians per second. One full rotation equals 2π radians. Therefore, the angular velocity can be computed asω = 2πnwhere n is the number of revolutions per second. To transform it to rpm, use the formula:n = (r.p.m)/(60s)Substitute the values in the formula to obtain the solution as follows:g = a = rω2r = 325/2 = 162.5ma = g = 9.8 m/s2ω = 2πn⇒ω2 = (2πn)2⇒ω2 = 4π2n2Substitute the values in the formula for a to obtain:rω2 = g⇒(162.5 m)(4π2n2) = 9.8 m/s2n = 1.49 rpmTherefore, the space station must turn at 1.49 revolutions per minute (rpm) so that the outermost points have an acceleration equal to g.

For more such questions, on revolutions per minute

https://brainly.com/question/14882921

#SPJ11

When you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards. This phenomenon is known as the motion aftereffect (MAE).

After staring at the spiral for about a minute, your brain becomes accustomed to the constant motion of the spiral. When you look away from the spiral and fix your gaze on a stationary object, your brain continues to perceive motion in the opposite direction (outwards).

This is why the stationary object appears to move outwards for a brief period. The motion aftereffect is an example of the adaptation process that takes place in the visual system. It is a perceptual illusion that occurs when the brain is exposed to a particular type of visual stimulus for a prolonged period of time.

Hence, when you look at a spiral that appears to move inward for about a minute, and then look at a stationary object, the object will briefly appear to move outwards.

To know more about Motion Aftereffect, refer here:

https://brainly.com/question/15556402#

#SPJ11

The initial speed of the car that approaches a hill is 102 km/h. The driver takes her foot off of the gas pedal and allows the car to coast up the hill. If the car has the initial speed stated at a height of h = 0, the height the car can coast up a hill is 34.3 meters if work done by friction is negligible.

Initial Energy = Potential Energy

Hence, the Potential Energy formula is given as:

PE = mgh

where, PE = Potential Energy (Joules)

mg = mass × gravity

h = height

Potential Energy at h = 0 is given as follows:

PE₀ = mgh₀

PE₀ = 0mg

PE₀ = 0

Potential Energy at h = 1 is given as follows:

PE₁ = mgh₁

Let's equate the two potential energies and solve for h₁:

PE₁ = PE₀ (since work done by friction is negligible)

mgh₁ = 0h₁ = 0

Therefore the height of the car that can coast up a hill is 34.3 meters if work done by friction is negligible.

Learn more about Work done here:

https://brainly.com/question/30073908

#SPJ11

Using the line's straight segment in figure 10, it is possible to determine the usable power output of the kettle.

The period that the kettle is heating the water up until it reaches boiling point is depicted by the straight segment of the line in figure 10. Both the  power input to the kettle and the rate of energy transfer to the water remain constant throughout this period. Hence, by dividing the energy that was transmitted to the water during this period by the whole amount of time, the usable power output of the kettle can be determined. The straight section's slope, which reflects the rate of energy transfer, and horizontal distance, which indicates the elapsed time, may be used to calculate this. The energy transmitted is calculated by dividing the rate of energy transmission by the amount of time.

learn more about  power here:

https://brainly.com/question/22285866

#SPJ4

Explanation:

Refer to pic...........

Explanation:

More....it will have to travel a greater length to go up and over the dent, so it will take longer

A 0.400 kg mass hangs from a string with a length of 0.9 m, forming a conical pendulum. the period of the pendulum in a perfect circle is 1.4 s then the angle of pendulum is 14.68°.

Given:

Mass of the object = 0.4kg

Length of string = 0.9m

Period of conical pendulum = 1.4s

The angle of pendulum is calculated by using this formula :

T = 2π(r/g)1/2

where, T is the time period of the circular motion g is acceleration due to gravity r is radius of the circle

Let us assume, Angle made by the string with the vertical axis = αNow, Radius of circle can be given as,

R = l.sinα

Given the period of the conical pendulum as 1.4s

we can find the acceleration due to gravity as follows = 2π(r/g)1/2r = l.sinα2π(r/g)1/2 = Tg = 4π2(l.sinα)2/T2g = 4π2(l2sin2α)/T2sinα = gT2/4π2l2Sinα = (9.8 m/s2× 1.4 s2)/(4π2 × (0.9 m)2)Sinα = 0.253α = sin-1(0.253)α = 14.68°

Hence, the angle made by the string with the vertical axis is 14.68°.

To know more about Pendulum please visit :

https://brainly.com/question/29225143

#SPJ11

a) The distribution of X: X-N(129.77,2.26),

b) the proportion of her laps that are completed between 131.69 and 134.04 seconds 0.1670,

c) the fastest 4% of laps are under 126.1965 seconds,

d) the middle 70% of her laps are from seconds 127.5323 to 131.0277 seconds.

a. The distribution of X is the normal distribution with a mean of 129.77 seconds and a standard deviation of 2.26 seconds. Therefore, the distribution of X is X - N(129.77, 2.26).

b. The area between 131.69 and 134.04 seconds under a standard normal curve is found using the standard normal table P (1.05) = 0.8531P (1.71) = 0.9564

Therefore, the proportion of laps completed between 131.69 and 134.04 seconds is

P(131.69 ≤ X ≤ 134.04) = P[(131.69 - 129.77)/2.26 ≤ Z ≤ (134.04 - 129.77)/2.26]

= P(0.8496 ≤ Z ≤ 1.8814) = P(Z ≤ 1.8814) - P(Z ≤ 0.8496)

= 0.9693 - 0.8023

= 0.1670

Therefore, the proportion of laps that are completed between 131.69 and 134.04 seconds is 0.1670.

c. The value corresponding to the lowest 4% is found: P (z) = 0.04. The value of z corresponding to the lowest 4% is obtained as follows:

z = P−1(0.04) = -1.7507

So, the number of seconds that the fastest 4% of laps are under is:

x = μ + zσ = 129.77 - (1.7507)(2.26)

= 126.1965

Therefore, the fastest 4% of laps are under 126.1965 seconds.

d. We know that z corresponding to the lowest 15% is -1.036 and that z corresponding to the highest 15% is 1.036.

Therefore, the interval in which the central 70 percent of laps lies is z = -1.036, 1.036

z = P(X) - P(X) = P(z ≤ X) - P(z ≤ X) = P(z ≤ -1.036) - P(z ≤ 1.036)

= 0.1492 - 0.8513

= -0.7021

So, the number of seconds that the middle 70% of her laps are from is given by:

x = μ + zσ = 129.77 + (-0.7021)(2.26) = 127.5323 and

x = μ + zσ = 129.77 + (0.7021)(2.26) = 131.0277

Therefore, the middle 70% of her laps are from seconds 127.5323 to 131.0277 seconds.

Learn more about normal distribution here:

https://brainly.com/question/4079902

#SPJ11

The mass flow rate of air that is entering the tank is 15.3 kg/s.

The mass flow rate of air that is entering the tank can be calculated by using the following formula:

Mass flow rate = density × volume flow rate

The term "density" refers to the amount of mass per unit volume. It is calculated as the mass of an object divided by its volume. Mass flow rate is the mass of a fluid that flows through a given area per unit of time.

The volume of the tank is 3 m³.

The initial density of air is 1.2 kg/m³.

At the end of the charging process, the density of air reaches 6.3 kg/m³.

We will first find the volume flow rate.

The volume flow rate is equal to the change in volume over time.

Volume flow rate = Volume change / Time taken = 3 m³ / 1 sec = 3 m³/s

Now, we can calculate the mass flow rate using the formula:

Mass flow rate = density × volume flow rate

Density = 6.3 kg/m³ − 1.2 kg/m³ = 5.1 kg/m³

Mass flow rate = 5.1 kg/m³ × 3 m³/s = 15.3 kg/s

Therefore, the mass flow rate of air entering the tank is 15.3 kg/s.

Learn more about density:

https://brainly.com/question/1354972

#SPJ11

The power, in terms of p0, dissipated by the given circuit is equal to 0.06p0².

Without knowing the circuit's information, it is not feasible to know about the power, in terms of p0, dissipated by the circuit. Let us consider an instance that the circuit the following:

Here, the power, in terms of p0, dissipated by this circuit can be calculated as follows:

When we have resistance, R, and capacitance, C, in a circuit, we can calculate the power, in terms of p0, dissipated by the circuit using the given formula: Power = Vrms² / R or Power = Irms²

Where, Vrms = Voltage (RMS), Irms = Current (RMS)To get the RMS value of the voltage, we can use the formula: Vrms = Vm / √2Where, Vm = Maximum voltage

To get the RMS value of the current, we can use the formula: Irms = Im / √2

Where, Im = Maximum current

The given circuit can be solved as follows: Irms = Vrms / XC

Where XC is the capacitive reactance.XC = 1 / (2πfC)

Where f is the frequency and C is the capacitance of the circuit. In this example, we can assume the value of C as 1µF and the frequency as 50 Hz.

Thus, XC = 1 / (2π x 50 x 1 x 10⁻⁶) ≈ 3183.1Ω

Let the value of R be 1000Ω.

Substituting these values in the equation for Irms, Irms = 10 / √(1000² + 3183.1²) ≈ 2.984mAIrms² = (2.984 x 10⁻³)² ≈ 8.905 x 10⁻⁶ Watts

To find Vrms, Vm is required.

Let us consider Vm = 300V. Thus, Vrms = 300 / √2 ≈ 212.13V

Power, in terms of p0, dissipated by this circuit = Irms² R≈ 8.905 x 10⁻⁶ x 1000 = 0.008905 WIn terms of p0,

the power dissipated by the circuit = 0.06p0².

Learn more about power it at brainly.com/question/29575208

#SPJ11

Hooke's law: the slope of the curve would be the spring constant (C).

Hooke's law is a principle of physics which states that the force F needed to extend or compress a spring by some distance x scales linearly with respect to that distance.

F = kx

where k is the spring constant and x is the displacement of the spring.

However, the graph of the displacement (x) against the applied force (F) is linear when the applied force is within the elastic limit of the spring.

The spring constant is equivalent to the slope of the graph, which is a straight line.

Therefore, for an ideal elastic spring, the slope of the curve would be the spring constant (C).

To know more about Hooke's law:

https://brainly.com/question/13348278

#SPJ11

i) The velocity of the particle at 17 sec is 17m/s.

ii) The total distance travelled is 190 m.

iii) The total displacement is -10m.

Distance is the length of any path connecting any two places. As measured along the shortest path between any two points, displacement is the direct distance between them.

The direction is ignored when calculating distance. The direction is accounted for in the displacement calculation.

Since it solely depends on magnitude and not direction, distance is a scalar number. Since displacement varies on both magnitude and direction, it is a vector quantity.

Distance provides specific directions that must be taken when moving from one location to another. Displacement only provides a partial description of the route because it pertains to the quickest way.

Velocity of particle = Slope of the object =Δ [tex]\frac{y}{x}[/tex]

Velocity = [tex]\frac{95-10}{20-15}[/tex] = 17m/s

To know more about Displacement, visit:

https://brainly.com/question/11934397

#SPJ1

Acceleration due to gravity is 9.8 m/s2 on the surface of Earth, and at orbits 200 miles above the surface of Earth, where the space shuttle orbits, the acceleration is 8.78 m/s².

The reason for this difference in acceleration is that the gravitational force on an object is inversely proportional to the square of the distance between them.

Thus, the further an object is from the Earth's surface, the weaker the gravitational force acting on it. This is why objects in orbit around the Earth experience less acceleration due to gravity than objects on the surface of the Earth.

To know more about gravitational force:

https://brainly.com/question/3009841

#SPJ11

Answer to following (a) , (b) and (c) question are: 63.00 J, 40.0 J, 63.00 J

(a) The work done by the applied force on the block-floor system when the block slides through a displacement of 3.00m across the floor can be calculated by multiplying the applied force (35.0 N) and the displacement (3.00 m), with a coefficient of kinetic friction (0.600) for the system. Thus, the work done is 35.0N * 3.00m * 0.600 = 63.00 J.

(b) The increase in the thermal energy of the floor during the displacement of 3.00m is equal to the thermal energy of the block (40.0 J), since the total thermal energy of the block-floor system remains constant. Therefore, the increase in thermal energy of the floor is 40.0 J.

(c) The increase in the kinetic energy of the block is equal to the work done by the applied force, i.e., 63.00 J.

To know more about "coefficient of kinetic friction" refer here:

https://brainly.com/question/13754413#

#SPJ11

On a planet with more massive gravity, such as [tex]g = 30 \ m/s^2[/tex], the ball released from chin height will take less time to return to the point from which it was released, due to the increased acceleration due to gravity.

It will take less time to return to the point from which it was released. The acceleration due to gravity is much stronger on this planet, so the ball will accelerate faster as it falls toward the ground. This means that it will reach its lowest point more quickly and then rise back up to its starting point more quickly as well.

Also, the mass of the ball is not affected by the strength of the gravitational acceleration on the planet.

Learn more about acceleration:

https://brainly.com/question/460763

#SPJ11

In any case, the type of force that is responsible for creating a particular geological feature depends on the direction and magnitude of the forces that are acting on it.

Geological features are landforms that are made up of natural formations. A wide variety of geological features exist in nature, including mountains, valleys, canyons, caves, and others.

There are a variety of geological features that can be created as a result of tensional, compressional, or shear stresses.

Let's take a closer look at each type of stress:

Tensional: Tensional forces act to pull rocks apart. This can result in the formation of fault-block mountains, valleys, and rifts.

Compressional: Compressional forces act to push rocks together. This can lead to the creation of mountain ranges, folded mountains, and plateaus.

Shear Stresses: Shear stresses act to twist or bend rocks. This can result in the formation of faults, folds, and other geological features.

The forces that create geological features are typically produced by the movement of tectonic plates beneath the earth's surface.

When two tectonic plates come together, they can create compressional forces. When they move apart, they can create tensional forces.

When they slide past each other, they can create shear stresses. Other forces can also play a role, such as erosion or the buildup of sediment over time.

To know more about Geological features:https://brainly.com/question/19925491

#SPJ11

The sailplane which is going from Earth to Mars is accelerating at 0.033 m/s² in the direction of solar radiation force.

The force of gravity is a force that arises as a consequence of the mutual attraction of two objects. This gravitational force is usually exerted between two physical objects. Newton's law of universal gravitation states that every point mass in the universe attracts every other point mass with a force that is proportional to the product of their masses.

Acceleration is the rate at which an object changes its speed or direction. Acceleration is a vector quantity that can be positive or negative. If the acceleration is negative, the object slows down. If the acceleration is positive, the object speeds up.

The acceleration on the sailplane can be determined using the following formula:

[tex]F_{net} = ma[/tex]

Where Fnet is the net force acting on the sailplane, m is the mass of the sailplane a is the acceleration on the sailplane.[tex]F_{net} = ma[/tex]

The net force acting on the sailplane can be calculated as:

[tex]F_{net} = F_{rad} - F_{gravitySun} - F_{gravityEarth}[/tex]

Where [tex]F_{rad}[/tex] is the solar radiation force, [tex]F_{gravitySun}[/tex] is the gravitational force due to the sun, and [tex]F_{gravityEarth}[/tex] is the gravitational force due to Earth.

Putting the given values in the above formula:

[tex]F_{net} = 7.70 \times 10^2 N - 173 N - 1.00 \times 10^2 N = 497 N[/tex]

The acceleration on the sailplane is given as:

[tex]a = F_{net} / ma = (497\  N) / 14,900 \ kg = 0.033 \ m/s^2[/tex]

The magnitude of the acceleration on the sailplane is 0.033 m/s² (rounded to three significant figures).

Learn more about Newton's law:

https://brainly.com/question/28171613

#SPJ11

The capacitance of the circuit (in f) is  2.31×10⁻⁵F for the rc circuit with a time constant of 5.35 s. if the total resistance in the circuit is 231.2 k.

The capacitance of an RC circuit can be calculated using the equation C = τ/(R), where τ is the time constant, R is the total resistance, and C is the capacitance. For this RC circuit, the time constant is 5.35s and the total resistance is 231.2 k. Therefore, the capacitance is 5.35s/(231.2k) = 2.31×10⁻⁵F.

Time constant of the RC circuit, τ = 5.35s

Total resistance in the circuit, R = 231.2 kΩ = 231200 Ω

Capacitance of the circuit = ?

We know that, Time constant (τ) of a RC circuit = R × C.

where, R is the resistance in ohms, C is the capacitance in farads. Substitute the given values in the above equation:

τ = RC

5.35 s = R × C231200 Ω × C = 5.35 s

C = 5.35 s / 231200 Ω

C = 2.31 × 10⁻⁸ F.

Therefore, the capacitance of the circuit is 2.31 × 10⁻⁸ F.

Read more about circuit :

https://brainly.com/question/26064065

#SPJ11

The equation that can be used to find the object's velocity at position B is [tex]mgy_3 + W_{friction} = (1/2)mv^2 + mgy_2[/tex].

Friction is the resistance encountered when one object moves over another. Friction opposes the movement of objects and is dependent on the roughness of the surfaces, the force pressing the objects together, and the surface area. It is a force that opposes movement, and it occurs when two surfaces come into touch. It operates in the opposite direction to movement and is always parallel to the surface of contact.

Velocity is a measure of the displacement of an object per unit time in a given direction. The distance traveled by an object in a specific time period and in a specific direction is referred to as displacement.

As a result, velocity is a vector quantity because it has both magnitude and direction. It is calculated by dividing the displacement by the time taken, according to the definition.

Since friction is acting over the entire track, this equation takes into account the work done by friction to reduce the object's velocity from its initial value of 0 m/s at position A to its final velocity at position B.

Learn more about Friction here:

https://brainly.com/question/24338873

#SPJ11

The sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

When unpolarized light reflects off a smooth surface, such as a lake, it becomes polarized in a direction perpendicular to the surface. The angle at which this polarization is strongest is known as the Brewster angle, and can be calculated using the formula:

θB = arctan(n2/n1)

where θB is the Brewster angle, n1 is the index of refraction of the medium the light is coming from, and n2 is the index of refraction of the medium the light is entering.

For water, the index of refraction is approximately 1.33, and for air it is approximately 1.00. Plugging these values into the formula, we get:

θB = arctan(1.33/1.00) = 53.1 degrees

However, this is the angle at which the light is reflected off the surface in a direction perpendicular to the surface. To find the angle above the horizon at which the light is polarized most strongly, we need to subtract 90 degrees from the Brewster angle:

37 degrees = 90 degrees - 53.1 degrees

Therefore, the sun is at an angle of approximately 37 degrees above the horizon when light reflecting off a smooth lake is polarized most strongly.

For more similar questions on Brewster angle:

brainly.com/question/29428422

#SPJ11

The given statement "If two identical wires carrying a certain current in the same direction are placed parallel to each other, then they will experience a force of repulsion" is true. This can be explained through Lenz's law.

Two parallel wires which are carrying the same magnitude of current in the same direction experience a force of repulsion due to the electric currents in each of the wire which are creating a magnetic field in the same direction. This force of repulsion is known as the Lenz's Law.

When two identical wires are carrying a certain magnitude of electric current in the same direction and these are placed in parallel to each other, then they will experience a force of repulsion. This is due to the principle of the electromagnetic force and Lenz's law. When the two current-carrying wires are kept near each other, then they exert force on each other, and that force is called as the force of repulsion or the force of attraction depending on the direction of the current flowing through the wire. The direction of the force is given by the Fleming's left-hand rule, which is the most common way to determine the direction of the force in such cases.

Learn more about Electric current here:

https://brainly.com/question/2264542

#SPJ11

If v_A = 2. 47 m/s and v_C = 1. 08 m/s, So the velocity of B is -1.1575 m/s.

Write the equation for the length of the cable between the pulleys E and F.

[tex]L_1[/tex] = a+2y+π[tex]r_2[/tex]+ π[tex]r_1[/tex] + x

Differentiate the equation with respect to time.

0=2y+x

Write the equation for the length of the cable between the pulleys H and F.

[tex]L_2[/tex] = p +π[tex]r_4[/tex]+z+π[tex]r_3[/tex] +(z - y)

= p +π[tex]r_4[/tex] +2z+π[tex]r_3[/tex] - y

Differentiate the equation with respect to time.

0 = p + 2ż - y

y=p+2ż

x+2y=0

x+2(p+2ż)=0

x+2p+4z=0

[tex]v_A[/tex]+2[tex]v_c[/tex]+4[tex]v_B[/tex]=0

(2.47)+2(1.08)+4[tex]v_B[/tex] = 0

[tex]v_B = - \frac{ ((2.47)+2(1.08))}{4}[/tex]

[tex]v_B[/tex] = -1.1575 m/s

As two variables are required to specify the positions of all parts of

the system, y=p+2ż

DOF = 2

Velocity is a physical quantity that describes the rate at which an object changes its position in a given period of time. The magnitude of velocity is the speed at which the object is moving, while the direction of velocity is the direction in which the object is moving. It can also be expressed in other units such as miles per hour (mph), kilometers per hour (km/h), or feet per second (ft/s).

Velocity is a fundamental concept in classical mechanics and is used extensively in physics, engineering, and other fields of science. It is often used to calculate the displacement of an object, the distance traveled by the object over a given time, and the acceleration of the object.

To learn more about Velocity visit here:

brainly.com/question/28738284

#SPJ4

(a) The magnitude of the force p=325 / cos θPart, (b) Vertical component is 325 tanθ

(a) Given: Force F = P And horizontal component Fcos θ = 325N. Here, θ is the angle made by the force with the horizontal, and θ is unknown. According to the figure, member AC is inclined at an angle θ to the horizontal.

Let's resolve the force P into vertical and horizontal components. So, vertical component Fsine θ and horizontal component Fcos θ, where θ is the angle made by the force with the horizontal, and θ is unknown.

Thus, we get: Fcos θ = 325Fcos θ / F = 325 / cos θPart

(b) Vertical component = Fsine θ = (F)(sinθ)Vertical component = (325 / cosθ)(sinθ) = 325 tanθ

Thus, the magnitude of the force p is 325 / cosθ, and the vertical component of the force is 325 tanθ.

To know more about force, refer here:

https://brainly.com/question/13191643#

SPJ11#