an airplane flies horizontally at a speed of 351 km/h and drops a crate that falls to the horizontal ground below. neglect air resistance.part (a) if the altitude of the plane was 580 m, then how far, horizontally in meters, did the crate move as it fell to the ground?

Answers

Answer 1

Refer to the attached photos. I would appreciate a rate :)

An Airplane Flies Horizontally At A Speed Of 351 Km/h And Drops A Crate That Falls To The Horizontal
An Airplane Flies Horizontally At A Speed Of 351 Km/h And Drops A Crate That Falls To The Horizontal

Related Questions

a 40cm diameter wheel accelerates uniformly from 240 rpm to 360 rpm in 6.5 seconds. how far will a point on the edge of the wheel have traveled in this time

Answers

Answer:

S = V1 t + 1/2 a t^2        distance traveled for linear acceleration

θ = ω1 t + 1/2 α t^2       equivalent angle for rotational acceleration

ω1 = 240 / min * 2 π * 240 / (60 s/min) = 8 π / s

ω2 = 360 rpm = 12 π / s

α = 4 π/ 6.5 s^2  = .62 π / s^2    angular acceleration

θ = 8 π / s  6.5 s + .62 π / 2 * 6.5^2

θ = 52 π + 13 π = 65 π = 65 * π / (2 π / rev) = 32.5 rev

1 rev = 2 * π * R = 2 * π * .4 m = 2.51 m / rev

S = 32.5 rev * 2.5 m/rev =  81 m

a dog lifts a 0.75 kg bone straight up through a distance of 0.11 m. How much work was done by the dog ?

Answers

The work done by the dog is 0.81J.

What is work done?

Work done is a measure of energy expended in moving an object; most commonly calculated by multiplying the force by the distance.

It is said that no work is done if the object does not move.

The work done on an object is the amount of energy transferred to an object through work.

According to this question, a dog lifts a 0.75 kg bone straight up through a distance of 0.11 m. The force applied to break the bone must be calculated first as follows:

Force = mass × acceleration

Force = 0.75kg × 9.8m/s²

Force = 7.35N

Work done = 7.35N × 0.11m = 0.81J

Therefore, 0.81J is the work done by the dog.

Learn more about work done at: https://brainly.com/question/2750803

#SPJ1

John walks to the pizza place for lunch. He walks 2 km north, then 1 km east. To get home, he walks 2 km west and 1 km south. What distance did he travel? What is his displacement?

Answers

Answer:

The total distance covered is 3 km and the displacement is 2.24 km.

Explanation:

For the total distance covered by Anthony, we just add all of the distances.

1 km (going east) + 1 km (going east again) + 1 km (going south) = 3 km

Hence, the his total distance covered when he went to the pizza place is 3 km.

Solving for the displacement is a different matter. We cannot just add all of the distances. From analysis of the problem, Anthony traveled and formed a right triangle. He traveled 1 km east twice, making it 2 km east in total, then he traveled 1 km south.

When dealing with a right triangle with 2 sides given (for this problem the two sides are the 2 km east and the 1 km south), we use the Pythagorean Theorem.

Solution:

c² = a² + b²  (Pythagorean Theorem)

c will be the longest side of the right triangle

a and b will be the other sides of the right triangle

c = √ (a² + b²)

c = √ (2² km + 1² km)

c = √5 km

c = 2.2361 km ≈ 2.24 km

Therefore, the displacement of Anthony is 2.24 km.

Read more about right triangle here:

brainly.ph/question/2449553

Know more about Pythagorean Theorem here:

brainly.ph/question/77971

WILL GIVE BRAINLY IF RIGHT
what would happen if you dropped, at the same time, particles of different shapes from a boat into still water

Answers

Explanation:

If you dropped particles of different shapes from a boat into still water, they would fall straight down due to the force of gravity. The speed at which they fall would depend on their mass and the shape of the particles could affect how they move through the water, but ultimately they would all sink to the bottom of the water body. If the particles are buoyant, they may float instead of sinking.

a constriction in a pipe reduces its diameter from 4.0 cm to 2.0 cm. where the pipe is narrow the water speed is 8.0 m/s. where it is wide the water speed is:

Answers

The velocity on the narrow side is 11.6 m/s. This is the velocity of the water in the narrow part of the pipe.

How to find velocity ?

To find the velocity of the water where the pipe is narrow, you can use the formula for the mass flow rate, which is given by:

Mass flow rate = Density * Flow rate

= Density * (Area * Velocity)

Where:

Density is the density of the fluid

Flow rate is the volume flow rate, or the rate at which volume flows through the pipe

Area is the cross-sectional area of the pipe

Velocity is the velocity of the fluid

The mass flow rate is constant, so you can set the mass flow rate on either side of the constriction equal to each other and solve for the velocity on the other side.

The cross-sectional area of the pipe on the narrow side is given by the formula for the area of a circle:

A = pi * r^2

Where:

A is the cross-sectional area of the pipe

r is the radius of the pipe

The radius of the pipe on the narrow side is 3 cm / 2 = 1.5 cm. Plugging this value into the formula for the cross-sectional area, you get:

A = pi * (1.5 cm)^2

= 7.07 cm^2

The cross-sectional area of the pipe on the wide side is given by the same formula, with a radius of 6 cm / 2 = 3 cm:

A = pi * (3 cm)^2

= 28.27 cm^2

Since the mass flow rate is constant, you can set the mass flow rates on either side of the constriction equal to each other and solve for the velocity on the other side:

(Density * 7.07 cm^2 * v) = (Density * 28.27 cm^2 * 8 m/s)

Solving for v, the velocity on the narrow side, you get:

v = (Density * 28.27 cm^2 * 8 m/s) / (Density * 7.07 cm^2)

= 11.6 m/s

The final value for the velocity on the narrow side is 11.6 m/s. This is the velocity of the water in the narrow part of the pipe.

To learn more about mass flow rate refer :

https://brainly.com/question/13289839

#SPJ4

1. A car moving 11 m/s accelerates at 1.5 m/s². How fast is it moving after it accelerates for 50
seconds?
Type a response (show work please)

Answers

We may be aware that, for example, a car leaving a stop sign would move farther in a given amount of time the faster it accelerates.

what an acceleration is?

acceleration is the rate of change in both speed of velocity over time. When anything moves faster or slower in a straight line, it is said to have been accelerated. So because direction is always shifting, motion on a circle accelerates even while the speed is constant.

What prompts accelerating?

An object's velocity is altered by a net force, and acceleration increases with net force. To accelerate at the same rate as less massive objects, more massive objects need greater net forces.

To know more about acceleration visit:

https://brainly.com/question/2303856

#SPJ1

disregarding friction, how far will the cart move in 3.2 s, starting from rest? answer in units of m.

Answers

If the cart moves in 3.2 seconds from rest, then the distance traveled by cart is 2 meters.

Which definition of distance suits you best?

How do you define distance? Regardless of direction, distance measures an object's overall movement. Distance is defined as the amount of ground covered by an object, regardless of its starting or stopping position.

Horizontal force acting on the cart, F = 11 N

Mass of the cart, m = 35 kg

To find,

Distance covered by the cart in 3.5 seconds if it starts from rest.

Solution,

Let x is the distance moved by the cart. It can be calculated using the second equation of motion as :

s = 1.925 meters

What is the definition of a distance?

In terms of "how much land an object is covered" while traveling, distance—a scalar quantity—describes this. Displacement is a vector number that expresses the overall change in the object's location, and it is related to the phrase "how far from place the thing is."

To know more about distance  visit:

https://brainly.com/question/15172156

#SPJ4

a 6.2 kg object heading north at 3.0 m/s collides with an 8.0 kg object heading west at 3.5 m/s. if these two masses stick together upon collision, what is their velocity after collision?

Answers

The velocity of both objetcs after the collision is 3.07m/sec if both object masses are 6.2 kg and 8.0kg respectively.

To find the velocity of both objects we need to conserve the momentum. We need to follow the law of conservation of momentum which states that initial momentum is equal to final momentum.

Now, we know that momentum =mass × velocity

So, initial momentum of first object=6.2×3=18.6Kg-m/sec

Similarly, initial momentum of second object=8×3.5=28.0kg-m/sec

Now, it is given that both object stick together, so total mass of both objects are=(6.2+8)=14.2kg

Now, both objects are moving with common velocity, so assume both have velocity v

=>So, final momentum of both objects is =14.2×v

according to law of conservation of momentum

=>18.6+25=14.2v

=>43.6=14.2v

=>v=43.6/14.2

=>v=3.07m/sec

Hence, final velocity of objects are 3.07m/sec.

To know more about velocity, visit here:

https://brainly.com/question/18084516

#SPJ4


A 20 kg wagon is pulled along the level ground by a rope inclined 30 degrees above the horizontal (friction is
negligible) (A) How large is the pulling force is the wagon accelerates of .40 m/s²? (B) What is the normal force of
the wagon?

Answers

Answer:

(A)   9.2 Newtons

(B)   200.8 Newtons

Explanation:

Attached is the free body diagram I drew along with some of the work/formulas I used. Please ask me any questions you have in the comments about my diagram/work. I'd be happy to walk you through it.

what is the equation describing the motion of a mass on the end of a spring which is stretched 8.8 cm from equilibrium and then released from rest, and whose period is 0.66 s ? assume that the displacement at the start of the motion is positive.

Answers

Answer:

x = A cos ω t          at t = zero, x displacement equals amplitude

x = .088 m cos ω t             describes the motion

We need yet to find ω in terms of P which is given

ω = √(k / m)        

P = 1 / f      and f = ω / (2 π)

Thus ω = 2 π f = 2 π / P       since 1 / f = P

This gives us

x = .088 m cos 2 π / .66 * t    

5. if the star sirius emits 23 times more energy than the sun, why does the sun appear brighter in the sky? include the terms luminosity and apparent brightness in your response.

Answers

The star Sirius is indeed brighter but our Sun appears to be brighter because it is closer to us.

The intrinsic luminosity of Sirius is exactly 25.4 times more than the sun but if we compare the distances of these stars, Sirius is 8.6 light years away from us and the Sun is just 8 light minutes away from us. This marks the obvious reason why our Sun appears more bright.

Even mathematically, it can be justified as the apparent brightness of any luminous object depends on the inverse square of the distance of that luminous object. Therefore the sun's light energy dominates our sky and we can't see any traces of Sirius from the earth.

Learn more about the star Sirius on

https://brainly.com/question/15851246?referrer=searchResults

#SPJ4

a hockey puck is hit on a frozen lake and starts moving with a speed of 13.20 m/s. exactly 5.6 s later, its speed is 6.60 m/s. what is the puck's average acceleration?

Answers

-1.17 is the average acceleration when a hockey puck is hit on a frozen lake and starts moving with a speed of 13.20 m/s. Perfectly,5.6 s later, its speed is 6.60 m/s.

What is an average acceleration?The rate of change in velocity, or the change in velocity per unit time, is known as average acceleration. The square of the distance over time is used to measure acceleration. Hence, the unit of acceleration is known to be as m/[tex]s^{2}[/tex]. Average is read as a symbol with a bar over it, so a-bar represents average acceleration.

Solution:

Given:

Initial sped =13.20m/sFinal speed=6.60m/stime taken=5.6s

Now, to find the average acceleration we use the following formula;

Acceleration, [tex]a_{avg}[/tex] =[tex]\frac{v^{final}-v^{initial} }{time}[/tex]

⇒[tex]a_{avg}[/tex]=6.60-13.20/5.6 = -1.17m/[tex]s^{2}[/tex]

Hence, -1.17 is the average acceleration when a hockey puck is hit on a frozen lake and starts moving with a speed of 13.20 m/s. Perfectly, 5.6 s later, its speed is 6.60 m/s.

To know more about acceleration visit

https://brainly.com/question/9095533

#SPJ4



a point at an antinode of the standing wave on the wire travels from its maximum upward displacement to its maximum downward displacement in 8.40 msms . what is the wire'??s mass?

Answers

The relation between the time-period of the transverse wave for the third harmonic and the time between the maximum displacement and minimum displacement is [tex]=16.3 \mathrm{~g}[/tex]

[tex]$$T_3=2 t$$Substitute$8.40 \mathrm{~ms}$[/tex]

for t in the above expression.

[tex]$$T_3=2(8.4 \mathrm{~ms})\left(\frac{10^{-3} \mathrm{~s}}{1 \mathrm{~ms}}\right)$$[/tex]

The wave velocity can be given by the following expression [tex]=0.0168 \mathrm{~s}[/tex]

[tex]v=\frac{\lambda_3}{T_3}[/tex]

Here,

[tex]$$\lambda_3$$[/tex]

is the frequency of third harmonics and

[tex]$$T_3$$[/tex]

is the time-period of third harmonics.

Substitute [tex]$0.1296 \mathrm{~m}$[/tex] for

[tex]$$\lambda_3$$[/tex]

and

[tex]$0.0168 \mathrm{~s}$ for$T_3$[/tex]

[tex]\begin{aligned}& v=\frac{0.1296 \mathrm{~m}}{0.0168 \mathrm{~m}} \\& =7.714 \mathrm{~m} / \mathrm{s}\end{aligned}[/tex]

The expression of the wave velocity is given by the following expression.

[tex]v=\sqrt{\frac{T}{m / L}}[/tex]

Rearrange the above expression for

[tex]$$m$$[/tex]

[tex]\text { Substitute } 5.00 \mathrm{~N} \text { for } T, 0.1944 \mathrm{~m} \text { for } L \text {, and } 7.714 \mathrm{~m} / \mathrm{s} \text { for } v \text { in the above expression. }[/tex]

[tex]\begin{gathered}m=\frac{(5.00 \mathrm{~N})(0.1944 \mathrm{~m})}{(7.714 \mathrm{~m} / \mathrm{s})^2} \\=(0.0163345 \mathrm{~kg})\left(\frac{1000 \mathrm{~g}}{1 \mathrm{~kg}}\right) \\=16.3 \mathrm{~g}\end{gathered}[/tex]

The anti-nodes in the standing waves are at a distance half a wavelength. The time-period is twice the time from maximum displacement to minimum displacement of the anti-node.

To learn more about displacement visit

https://brainly.com/question/11934397

#SPJ4

a vertical spring scale can measure weights up to 210 n . the scale extends by an amount of 13.5 cm from its equilibrium position at 0 n to the 210 n mark. a fish hanging from the bottom of the spring oscillates vertically at a frequency of 2.15 hz . part a ignoring the mass of the spring, what is the mass m of the fish?

Answers

sheesh sheesh                                                    

Explanation:

the force between between two objects increases by what factor if the distance between them is changed 4.5 times the original separation?

Answers

The new gravitational force between the object will be 1/20.25 times of the original force.

The gravitational force between any two object is defined as the product of the masses of the object and it is inversely proportional to the square of the distance between them which is given by,

F = GMm/R²

Here,

G is the universal gravitational constant, M and m are the mass of the body and R is the distance between them.

As per the given question the distance between the object is increased 4.5 times the original separation.

R' = 4.5R.

The new force of attraction between the object will be,

F' = GMm/(R')²

F' = GMm/(4.5R)²

F' = GMm/20.25R²

F' = F/20.25

So, the new force of attraction between the two objects will become 1/20.25 times of original force.

To know more about gravitational force , visit,

https://brainly.com/question/24783651

#SPJ4

Classify the type of reaction below.
C2H6 + O2
--> CO2 + H2O
a. Synthesis
b. Decomposition
c. Combustion
d. Single Replacement
e. Double Replacement

Answers

Answer: Synthesis

Explanation: You are combining multiple Elements

Question 8 of 20
You heat a pot of water on a gas stove. Not all the energy from the
combustion of the gas is transformed into thermal energy. What happens to
the rest of the energy released when the gas burns?
OA. It is transformed into light energy.
OB. It is transformed into chemical energy.
C. It is transformed into electrical energy.
OD. It is transformed into nuclear energy.
SUBMIT

Answers

Answer:

None of the choices you provided are correct. When a gas burns, it releases energy in the form of heat and light. Some of this energy is transferred to the pot of water, increasing its temperature, but some of the energy is also released as light. However, the rest of the energy is not transformed into chemical, electrical, or nuclear energy. Instead, it is lost to the environment in the form of waste heat. This is why gas stoves can become hot to the touch - they are releasing excess energy in the form of heat that is not being used to heat the pot of water.

Explanation:

A physics student walks 6 meters east, 4 meters north, then 9 meters
west. What is the student's magnitude of displacement from starting
position?

Answers

Answer:

5 m

Explanation:

Displacement is the straight-line distance from the starting point to the end point.  Student ends up 4m north and 3m west from where he started. Use pythagorean theorem to solve for displacement (d).  

d² = 3² + 4² = 25

d = [tex]\sqrt{25}[/tex] = 5 m

Or, if you remember from geometry, a right triangle with legs of 3 and 4 has a hypotenuse of 5 (3-4-5 right triangle)

a 1,402-kg car rounds an unbanked curve with a radius of 53 m at a speed of 9.9 m/s. what minimum coefficient of friction must exist between the road and tires to prevent the car from slipping?

Answers

To keep the car from slipping, the road and tires need to have a minimum coefficient of friction of 0.188.

The things creating friction will determine the coefficient of friction. The value is often between 0 and 1, but it can also be higher. A number of 0 indicates that there is absolutely no friction between the items; superfluidity makes this feasible. Yes. Because the adhesive forces between molecules are stronger when the contact surface is substantially polished, frictional force increases. In this situation, the friction coefficient will be higher than one.

Here m= 1402 kg

r=53

v= 9.9 m/s

g=9.8

coefficient = (v^2) / rg

coefficient = (9.9^2) / (53*9.8)

coefficient = 98.01/519.4

coefficient = 0.188

Learn more about friction Visit : brainly.com/question/24338873

#SPJ4

Uing two billiard ball and 3 to 4 entence decided experiment to demontrate the law of conervation of momentum. (4 point)

Answers

So let's talk about billiard balls and the law of conservation of momentum. For the purposes of this simplified discussion, momentum is always conserved for collisions between balls.

What is momentum?Momentum is a commonly used term in sports. A team that has the momentum is on the move and is going to take some effort to stop. A team that has a lot of momentum is really on the move and is going to be hard to stop. Momentum is a physics term; it refers to the quantity of motion that an object has. A sports team that is on the move has the momentum. If an object is in motion (on the move) then it has momentum.Momentum can be defined as "mass in motion." All objects have mass; so if an object is moving, then it has momentum - it has its mass in motion. The amount of momentum that an object has is dependent upon two variables: how much stuff is moving and how fast the stuff is moving. Momentum depends upon the variables mass and velocity. In terms of an equation, the momentum of an object is equal to the mass of the object times the velocity of the object.

To learn more about velocity refer to:

https://brainly.com/question/25749514

#SPJ4

an object in shm oscillates with a period of 4.0 s and an amplitude of 16 cm. part a how long does the object take to move from x

Answers

The object takes to move is 0.409s.

Calculaiton:

time period T = 4 s

Angular speed ω = 2π/T= 1.57 rad/s

SHM equation

x = A sin ωt

6 = 10 sin(1.57t)

sin(1.57t) = 0.6

1.57 t = 0.6435

t= 0.409s.

The amplitude of a periodic variable is a measure of its change over one period. The amplitude of an aperiodic signal is its magnitude relative to a reference value. Amplitude has various definitions, all of which are functions of the magnitude of the difference between extreme values ​​of a variable. It refers to the maximum displacement from equilibrium exhibited by a body in periodic motion.

Learn more about The amplitude here:- https://brainly.com/question/3613222

#SPJ4

when you looked at solar activity on the heliophysics event registry website, on which date did you find activity on the sun?

Answers

You did look at solar activity on the heliophysics event registry website, and we found activity on the sun on the specified day.

What three sorts of solar occurrences are there?

Any natural occurrence in the upper atmosphere of the sun is referred to as a solar phenomenon. Solar flares, prominences and filaments, and coronal mass ejections are three different categories of solar phenomena.

How can I follow the cycle of solar activity the best?

The simplest way we can investigate how solar activity changes over time is to survey sunspots, which is also how we track the solar cycle. Sunspots are associated with the Sun's natural 11-year cycle, during which the planet's surface changes from calm to turbulent.

To know more about  solar activity visit:-

https://brainly.com/question/3013261

#SPJ4

Maher is trying to find the density of a plastic toy. The toy’s mass is 160 g.
Maher placed the toy in a graduated cylinder that has 70 ml of water, the water level increased
till 150 ml.
a) Find the toy’s volume.

Answers

The volume of the toy is 80 ml.

To find the volume of the plastic toy, Maher can use the principle of buoyancy. When an object is placed in a fluid, it will displace an amount of fluid equal to its own volume. The volume of the displaced fluid can be measured and used to calculate the volume of the object.

In this case, Maher has placed the toy in a graduated cylinder filled with water, and he has observed that the water level increased from 70 ml to 150 ml. This means that the toy displaced 150 - 70 = 80 ml of water.

The volume of the toy is equal to the volume of the displaced water, so the toy's volume is 80 ml. This is the volume of the toy when it is completely submerged in water.

It's important to note that the volume of an object can change depending on its temperature, pressure, and other factors. To get an accurate measurement of the volume of the toy, Maher should make sure to measure the volume of the displaced water carefully and under controlled conditions.

Answer:

Volume of the toy: [tex]80\; {\rm mL}[/tex].

Average density of the toy: [tex]2\; {\rm g\cdot mL^{-1}}[/tex] (or equivalently, [tex]2\; {\rm g \cdot cm^{-3}}[/tex].)

Explanation:

The graduated cylinder initially measures the volume of water in this cylinder:

[tex]V(\text{water}) = 70\; {\rm mL}[/tex].

Assume that the toy is submerged in the water. The graduated cylinder would then measure the volume of the water and the toy, combined:

[tex]V(\text{water}) + V(\text{toy}) = 150\; {\rm mL}[/tex].

Rearrange to find the volume of the toy:

[tex]\begin{aligned}V(\text{toy}) &= 150\; {\rm mL} - V(\text{water}) \\ &= 150\; {\rm mL} - 70\; {\rm mL} \\ &= 80\; {\rm mL}\end{aligned}[/tex].

To find the average density of this toy, divide mass by volume:

[tex]\begin{aligned}(\text{average density}) &= \frac{(\text{mass})}{(\text{volume})} \\ &= \frac{160\; {\rm g}}{80\; {\rm mL}} \\ &= 2\; {\rm g\cdot mL^{-1}}\end{aligned}[/tex].

a car accelerates uniformly from rest to 25 m/s over a distance of 30 meters. what is the acceleration of the car?

Answers

Answer:

a=25/24 m/s^2

Explanation:

I’m going to assume you mean the final velocity is 25m/s.

v^2=u^2+2as

625=0+2a300

a=25/24 m/s^2 or 1.0416^_ (period 1) ^m

a dad pushes tangentially on a small hand-driven merry-go-round and is able to accelerate it from rest to a frequency of 15 rpm in 10.0 s. assume the merry-go-round is a uniform disk of radius 2.5 m and has a mass of 330 kg, and two children (each with a mass of 25 kg) sit opposite each other on the edge. calculate the torque required to produce the acceleration, neglecting frictional torque. what force is required at the edge?

Answers

Refer to the photo taken.

an increase in sound level from 30 db to 50 db requires an increase in sound intensity by a factor of:

Answers

Loudness increases by 10 dB for every dB increase in sound intensity. A 40-decibel light rainstorm is 100 times louder than a whisper, whereas a 30-decibel "silent" room is 10 times louder than a 20-decibel whisper. Loud noises can be harmful.

50 dB is how much louder than 20 dB?

A 10 dB rise results in a two-fold increase in volume. The loudness will therefore rise by nearly 8 times with a 30 dB increase (from 20 dB to 50 dB).

Decibels are measured on a logarithmic scale using a power of ten, which might be perplexing. For those of you without advanced math degrees, this simply implies that the sound intensity doubles for every 10 decibel rise.

learn more about Decibels refer

https://brainly.com/question/28375244

#SPJ4

what should the rotation curve for this galaxy look like for radii larger than 5 kpc, do you think? after 5kpc...

Answers

The rotation curve for this galaxy look like for raddi larger than 5kpc is angular velocity.

What is angular velocity?

Angular velocity is the speed at which the angle between 2 bodies changed whenever an object rotated or revolvers around an axis. This displacements is depicted in the images by the angle firmed by a line on one body andar a line on the other.

Angular velocity can be defined as the Speed at which an item rotates or revolvers around an axis. The Greeks letter Omega (occasionally ) stands for angular velocity. The SI unit for angular velocity is radians per second because it is the expressed as an angle per unit of times.

Orbital speed increase with radius beacuse it is directly proportional to radius  

Since V=wr

So on increasing with radius orbital speed also increases.

So here w is angular velocity.

To know more about angular velocity click-

https://brainly.com/question/20432894

#SPJ4

two planets are identical, except planet x has an atmosphere of mostly nitrogen and planet y has an atmosphere of mostly carbon dioxide. what can you determine about the planets

Answers

Two planets are identical, except planet x has an atmosphere of mostly nitrogen and planet y has an atmosphere of mostly carbon dioxide therefore what we can determine about the planets is that x is Earth while y is Venus.

What is Atmosphere?

This is referred to as the envelope of gases surrounding the earth or another planet and it makes life possible by providing different organisms with air to breathe

In the atmosphere of the planet Venus there is a high concentration of carbon dioxide as it is made up of  it is made of 96.5% of CO₂ and a 3% of nitrogen.

On the other hand in the atmosphere of the planet Earth, there is a high concentration of nitrogen which is about 78% and is therefore the reason why they were chosen as the correct choices.

Read more about Atmosphere here https://brainly.com/question/24925283

#SPJ1

1. Find the force due to gravity if the mass of the object is 2300 kg
and the mass of the other object is 4000 kg. The distance
between the two objects is 0.150 m.

Answers

The force due to gravity will be 0.0272 Newtons.

What exactly does gravitational force signify?

The force between two mass-containing objects that are drawn toward one another is referred to as the gravitational pull. There is gravity everywhere around us. For instance, it maintains the planets in our solar system in orbit around the Sun. Additionally, because to gravity, the Moon maintains its orbit around the Earth.

How to calculate gravitational force in the above question?

Despite being weak and appealing, gravitational forces exist.

Given, mass of one object= 2300 kg

mass of another object= 4000 kg

distance between the two objects= 0.150 m

value of G is universal, [tex]G= 6.67[/tex]×[tex]10^{-11}[/tex] [tex]N m^{2} / kg^{2}[/tex]

the equation is, [tex]F=G\frac{M1 . M2}{d^{2} }[/tex]

                       [tex]F=0.0272 N[/tex]

To know more about Gravitation visit

https://brainly.com/question/3009841

#SPJ4

if we have a system that uses 5 volts with a frequency of 1ghz and the power used is 3 watts, what is the power draw when we increase the frequency to 3ghz?

Answers

Processor-A uses 20 W of power components and 80 W cpu dynamic power 3 GHz.

Static power: What does that mean?

When there is no design activity occurring, static power—also known as "leakage"—is used up. It closely relates to the transistor's idle current, which is based on the transistor's characteristics.

Power is it static or is it dynamic?

While leakage, or the current that passes through a transistor while there is no activity, makes up static power, switching or short-circuit power are components of dynamic power. Any of the following things may influence each power component's value: Activity. Frequency.

To know more about  static power visit:

https://brainly.com/question/26609519

#SPJ4

Other Questions
Write an equation that passes through the point (4,-3) and is perpendicular to the line 4x+y=3 (q009) william j. goode identifies several important changes in global family and marriage patterns. one of the main effects of these changes is that they are The cost of a cake is twice that of a cup of tea.1 cake and 5 cups of tea cost 21.How much does a cake cost? An X.509 v3 certificate binds a _____, which uniquely identifies a certificate entity, to a user's public key. The sum of three numbers is 96. The first number is 6 less than the second. The third number is 4 times the second. What are the numbers? bro help me rn ill actually cms bro Ginny is in the research phase of writing her story. What is one activity she might be doing? A. spell checking her story for errors B. writing the first rough version of her story C. choosing the angle of her story and how shell approach it D. interviewing sources and taking notes a cellist tunes the c-string of her instrument to a fundamental frequency of 65.4 hz. the vibrating portion of the string is 0.615 m long and has a mass of 14.8 g . the absence of key or tonality in a musical composition is known as _________. group of answer choices a.ostinato. b.a tone cluster. c.atonality. d.polytonality. ntroduction Between the 1830s and the beginning of the Civil War in 1861, the American South expanded its wealth and population and became an integral part of an increasingly global economy. The South actively engaged new technologies and trade routes while also seeking to assimilate and upgrade its most "traditional" and culturally ingrained practices within a modernizing world. 1830s, merchants from the Northeast, Europe, Canada, Mexico, and the Caribbean flocked to southern cities, setting up trading firms, warehouses, ports, and markets. Populations became more cosmopolitan, more educated, and wealthier. 14. Between a pair of points on the line y = 5x-2, suppose that the rise is 15.Then the run is...(A) 3(B) 4(C) 5(D) 10 T/F Well-written social media policies of a firm are consistent with its organizational culture and values. Describe the lifestyle of the tribals and nomads? a right turn starts in the right-hand lane and end in: any lane available the lane closest to the curb the left lane submit answer Formula fo chemical compound? Copper(1) hypochlorite due now pls help!!!!!!!!!!! Which statement best expresses a theme of thestory? Spunk 4. 8 friends are lining up to get in to see the Hunger Games: Catching Fire movie,including Bob and SamA) What is the probability that Bob and Sam will be next to each other. A buffer solution is prepared that is 0.18 M NH3 and 0.27 M NH4Cl. What is the pH of this buffer? Kb for NH3 is 1.8 x 10-5The correct answer is: 9.08Can someone explain how to do this for me? Lines DE and AB intersect at point C.What is the value of x?A.12B.25C.38D.05 The surface of the Earth is made of several tectonic plates that move at a very slow rate. What causes the plates to move?a.explosions within the Earth's mantleb.convection currents within the Earth's mantlec.expansion of the Earth's core pushing on the tectonic platesd.contraction of the Earth's core pulling on the tectonic plates