An ac generator consists of a coil with 40 turns of wire, each with an area of 0.06 m2 . The coil rotates in a uniform magnetic field B = 0.4 T at a constant frequency of 55 Hz. What is the maximum induced emf?

a. 625 V
b. 110 V
c. 421 V
d. 332 V
e. 200 V

Answers

Answer 1

Answer:

d. 332 V

Explanation:

Given;

number of turns in the wire, N = 40 turns

area of the coil, A = 0.06 m²

magnitude of the magnetic field, B = 0.4 T

frequency of the wave, f = 55 Hz

The maximum emf induced in the coil is given by;

E = NBAω

Where;

ω is angular velocity = 2πf

E = NBA(2πf)

E = 40 x 0.4 x 0.06 x (2 x π x 55)

E = 332 V

Therefore, the maximum induced emf in the coil is 332 V.

The correct option is "D"

d. 332 V


Related Questions

What type of energy conversion occurs when you place your feet near the fireplace and they become warm?
O Radiant to thermal
o Thermal to mechanical
O Mechanical to chemical
O Nuclear to thermal​

Answers

Answer:

It is the first one RADIENT TO THERMAL

Explanation:

The heat emitted from the campfires is an an example of radiant energy and thermal energy is refers to the energy contained within a system that is responsible for its tempreture with in this case is the campfires and heat energy being reflected upon your feet.

Answer:

A

Explanation:

A fisherman in a stream 39 cm deep looks downward into the water and sees a rock on the stream bed. How deep does the stream appear to the fisherman

Answers

Answer:

30cm

Explanation:

assume that the eyes are substantially above the water so that sin(theta) is approximately theta.

( small angle approximation).

The point at which a ray leaving the fish hits the surface of the water is x to the side of the centreline and the depth of the water is d

x/d = sin( angle of incidence)

if the apparent depth of the water is h then

x/h = sin( angle of refraction)

and applying snells law

1 sin ( theta air) = 1.33 sin( theta water)

1 * x/h = 1.33 * x/d

d/h = 1.33

or h/d = 1/1.33

h/39 = 1.33

h = 39 /1.33 so that is the apparent depth of the stream assuming:-

1. Your eyes are almost directly overhead

and

2. your eyes are a significant distance above the surface of the water.

x/d = 1.33 x/h

h/d =39/1.3

= 30cm

Do an Internet search to determine what minerals are extracted from the ground in order to manufacture the following products:

a. Stainless steel utensils

b. Cat litter

c. Tums brand antacid tablets

d. Lithium batteries

e. Aluminum beverage cans

Answers

Answer:

Raw materials are most times gotten from the earth through various forms of extraction procedures.

A) Stainless steel utensils is made up of mainly Iron and other elements such as chromium , carbon etc.

B) Cat litter comprises of ceramic products which is made up of clay.

C) Tums brand antacid tablets comprises of calcium carbonate, magnesium hydroxide, aluminum hydroxide and sodium bicarbonate which could be extracted from the earth.

D)Lithium batteries are made up of elements in the earth such as lithium and carbon.

E)Aluminum beverage cans are made up of aluminum extracted from the ground.

As you finish listening to your favorite compact disc (CD), the CD in the player slows down to a stop. Assume that the CD spins down with a constant angular acceleration. If the CD rotates clockwise (let's take clockwise rotation as positive) at 500 rpm (revolutions per minute) while the last song is playing, and then spins down to zero angular speed in 2.60 s with constant angular acceleration, the angular acceleration of the CD, as it spins to a stop at -20.1 rad/s 2. How many revolutions does the CD make as it spins to a stop?

Answers

Answer:

10.8rev

Explanation:

Using

Wf²-wf = 2 alpha x theta

0²- 56.36x56.36/ 2(-20.13) x theta

Theta = 68.09 rad

But 68.09/2π

>= 10.8 revolutions

Explanation:

15. Food chain always start with
a. Photosynthesis
Decay
b. Respiration
d. N2 Fixation
C.Photosynthesis​

Answers

Answer: Photosynthesis

Explanation: every food chain starts with plant life, therefore photosynthesis comes first.

A quantity of an ideal gas is compressed to half its initial volume. The process may be adiabatic, isothermal or occurring at constant pressure. Rank those three processes in order of the work required of an external agent, least to greatest. A : adiabatic, isothermal, constant pressure B : constant pressure, isothermal, adiabatic C : adiabatic, constant pressure, isothermal D : isothermal, adiabatic, constant pressure E : constant pressure, adiabatic, isothermal

Answers

Answer:

B. constant pressure, isothermal, adiabatic

Explanation:

A quantity of an ideal gas is compressed to half its initial volume.

The process may be adiabatic, isothermal or occurring at constant pressure.

Adiabatic-constant heat

Constant pressure or isobaric

Isothermal or constant temperature

An external agent is a system that does work on a system or a machine.

This external agent applies force , or changes the state of the body it is acting on.

In order of the work required of an external agent, least to greatest

The following processes will be arranged.

constant pressure, isothermal, adiabatic

A satellite of mass m circles a planet of mass M and radius R in an orbit at a height 2R above the surface of the planet. What minimum energy is required to change the orbit to one for which the height of the satellite is 3R above the surface of the planet

Answers

Answer:

ΔE = GMm/24R

Explanation:

centripetal acceleration a = V^2 / R = 2T/mr

T= kinetic energy

m= mass of satellite, r= radius of earth

= gravitational acceleration = GM / r^2

Now, solving for the kinetic energy:

T = GMm / 2r = -1/2 U,

where U is the potential energy

So the total energy is:

E = T+U = -GMm / 2r

Now we want to find the energy difference as r goes from one orbital radius to another:

ΔE = GMm/2 (1/R_1 - 1/R_2)

So in this case, R_1 is 3R (planet's radius + orbital altitude) and R_2 is 4R

ΔE = GMm/2R (1/3 - 1/4)

ΔE = GMm/24R

A diffraction grating with 161 slits per centimeter is used to measure the wavelengths emitted by hydrogen gas. At what angles in the first-order spectrum would you expect to find the two violet lines of wavelength 434 nm and of wavelength 410 nm

Answers

Answer:

[tex]\theta_1 = 0.400^o[/tex]

[tex]\theta_2 =0.378^o[/tex]

Explanation:

From the question we are told that

    The  number of slits per cm is  k =  [tex]161\ slits\ per\ cm = 161 \ slits\ per\ 0.01 m[/tex]

    The order of the maxima is  n =  1

    The wavelength are  [tex]\lambda_1 = 434 nm = 434 *10^{-9} \ m \ \ \ , \lambda_2 = 410nm = 410 *10^{-9} \ m[/tex]

The  spacing between the slit is mathematically represented as

           [tex]d = \frac{ 0.01}{k}[/tex]

=>       [tex]d = \frac{ 0.01}{161}[/tex]

=>         [tex]d = 6.211 *10^{-5} \ m[/tex]

Generally the condition for constructive interference is  

        [tex]n\lambda = d \ sin \theta[/tex]

At  [tex]\lambda_1[/tex]

      [tex]\theta _1 = sin^{-1} [ \frac{1 * 434 *10^{-9}}{6.211 *10^{-5}} ][/tex]

      [tex]\theta_1 = 0.400^o[/tex]

At  [tex]\lambda_2[/tex]

       [tex]\theta _2 = sin^{-1} [ \frac{1 * 410 *10^{-9}}{6.211 *10^{-5}} ][/tex]

       [tex]\theta_2 =0.378^o[/tex]

The elastic portion of the downward-sloping straight-line demand curve lies:_______
a. at the intersection with the supply curve.
b. anywhere to the right of the current market price.
c. above the point of unit elasticity.
d. below the point where total revenue is maximized.

Answers

Answer:

c. above the point of unit elasticity.

Explanation:

The elastic portion of the downward-sloping straight-line demand curve lies above the point of unit elasticity. Supply and demand are fundamental concept in economics. The demand curve shows how much of a good people will want at a different prices. The demands curves illustrates the intuition why people purchase a good for a lower price. For the demand curve, the price is always shown on the vertical axis and the demand curve is shown on the horizontal axis. Thus , the quantity demanded increases as the price gets lower. However, the price elasticity of the demand curve varies along the demand curve. This is because there is a key distinction between the gradient and the elasticity. The gradient which is the slope of the line is always the same in the demand curve but elasticity of the demand changes in the percentage of the quantity demand. Therefore, elasticity will vary along the downward-sloping straight - line demand curve. So,  in a downward-sloping straight-line demand curve, the elastic portion is usually above the  point of unit elasticity

It's nighttime, and you've dropped your goggles into a 3.2-m-deep swimming pool. If you hold a laser pointer 1.2 m above the edge of the pool, you can illuminate the goggles if the laser beam enters the water 2.0 m from the edge.
How far are the goggles from the edge of the pool?

Answers

Answer:

Explanation:

Laser angle with water surface is given by: Tan α = 1/2.0= 0.5/

α = 26.56°

Laser angle with Normal = 90 - 26.56 = 63.44 °

Assuming a red laser, refractive index in water is 1.331.

Angle of refraction in water is given by:

Ref Ind = Sin i / Sin r

1.331 = Sin 63.44 / Sin r

Sin r = 0.8945 / 1.331 = 0.6721

Angle r = 42.22°

For the path in water:

Tan 42.22 = x / 3.2

x = 2.9m where x is the lateral displacement of the laser ince it hits the water

So the goggles are 2.0 + 2.9 = 4.9 m from edge of pool

Can a person break a wall with a punch?(I mean technically,maybe with inhuman speed)​

Answers

Answer:

yes, shaolin monks can do. you can find tutorials on Youtb

A cylinder rotating about its axis with a constant angular acceleration of 1.6 rad/s2 starts from rest at t = 0. At the instant when it has turned through 0.40 radian, what is the magnitude of the total linear acceleration of a point on the rim (radius = 13 cm)?


a. 0.31 m/s^2

b. 0.27 m/s^2

c. 0.35 m/s^2

d. 0.39 m/s^2

e. 0.45 m/s^2

Answers

Answer:

The magnitude of the total linear acceleration is 0.27 m/s²

b. 0.27 m/s²

Explanation:

The total linear acceleration is the vector sum of the tangential acceleration and radial acceleration.

The radial acceleration is given by;

[tex]a_t = ar[/tex]

where;

a is the angular acceleration and

r is the radius of the circular path

[tex]a_t = ar\\\\a_t = 1.6 *0.13\\\\a_t = 0.208 \ m/s^2[/tex]

Determine time of the rotation;

[tex]\theta = \frac{1}{2} at^2\\\\0.4 = \frac{1}{2} (1.6)t^2\\\\t^2 = 0.5\\\\t = \sqrt{0.5} \\\\t = 0.707 \ s\\\\[/tex]

Determine angular velocity

ω = at

ω = 1.6 x 0.707

ω = 1.131 rad/s

Now, determine the radial acceleration

[tex]a_r = \omega ^2r\\\\a_r = 1.131^2 (0.13)\\\\a_r = 0.166 \ m/s^2[/tex]

The magnitude of total linear acceleration is given by;

[tex]a = \sqrt{a_t^2 + a_r^2} \\\\a = \sqrt{0.208^2 + 0.166^2} \\\\a = 0.266 \ m/s^2\\\\a = 0.27 \ m/s^2[/tex]

Therefore, the magnitude of the total linear acceleration is 0.27 m/s²

b. 0.27 m/s²

A nearsighted person has a far point that is 4.2 m from his eyes. What focal length lenses in diopters he must use in his contacts to allow him to focus on distant objects?

Answers

Answer:

-0.24diopters

Explanation:

The lens is intended that makes an object at infinity appear to be 4.2 m away, so do=infinity, dI = - 4.2m (minus sign because image is on same side of lens as object)

So 1/do +1/di = 1/f

1/infinity + 1/-4.2 = 1/f

1/f = 1/-4.2 = -0.24diopters

Several books are placed on a table. These books have a combined weight of 25 N and cover an area of 0.05 m2. How much pressure do the books exert on the table? The pressure the books apply to the table top is __ Pa.

Answers

Answer:

500 Pascals

Explanation:

[tex]Force = 25N\\Area = 0.05m^2\\\\Pressure = \frac{Force}{Area}\\ \\Pressure = \frac{25}{0.05}\\\\ Pressure = 500 Pascals[/tex]

A city of punjab has 15 percemt chance of wet weather on any given day. What is probability that it will take a week for it three wet weather on 3 sepaprate days? Also find it standard deviation

Answers

Answer:

The probability that it will take a week for it three wet weather on 3 separate days is 0.06166 and its standard deviation is 0.9447

Explanation:

We are given that A city of Punjab has 15 percent chance of wet weather on any given day.

So, Probability of wet weather = 0.15

Probability of not being a wet weather = 1-0.15 =0.85

We are supposed to find probability that it will take a week for it three wet weather on 3 separate days

Total number of days in a week = 7

We will use binomial over here

n = 7

p =probability of failure = 0.15

q = probability of success=0.85

r=3

Formula :[tex]P(r=3)=^nC_r p^r q ^{n-r}[/tex]

[tex]P(r=3)=^{7}C_{3} (0.15)^3 (0.85)^{7-3}\\P(r=3)=\frac{7!}{3!(7-3)!} (0.15)^3 (0.85)^{7-3}\\P(r=3)=0.06166[/tex]

Standard deviation =[tex]\sqrt{n \times p \times q}[/tex]

Standard deviation =[tex]\sqrt{7 \times 0.15 \times 0.85}[/tex]

Standard deviation =0.9447

Hence The probability that it will take a week for it three wet weather on 3 separate days is 0.06166 and its standard deviation is 0.9447

A father and his son want to play on a seesaw. Where on the seesaw should each of them sit to balance the torque?

Answers

Answer:

A The father should sit closer to the pivot.

C The longer wrench makes the job easier because less force is needed when there is more distance from the pivot.

A As far from the head of the hammer as possible because this will maximize torque.

D at the opposite side of the seesaw towards the middle

:) gl

Explanation:

If a father and his son want to play on a seesaw then to balance the torque of the seesaw the father should sit near the pivot as he had more weight as compared to his son, while the son should sit a little farther from the pivot point as compared to his father.

What is the mechanical advantage?

Mechanical advantage is defined as a measure of the ratio of output force to input force in a system, It is used to analyze the forces in simple machines like levers and pulleys.

Mechanical advantage = output force(load) /input force (effort)

As given in the problem statement If a father and his son wish to play on a seesaw,

The father should sit close to the pivot because he weighs more than his son, and the son should sit a little farther away from the pivot point than his father. This will help balance the torque of the seesaw.

Thus, the father should sit near the pivot on the one side and the son should sit a little farther from the pivot of a seesaw on the other side.

Learn more about Mechanical advantages, here

brainly.com/question/16617083

#SPJ2

A third wire of the same material has the same length and twice the diameter as the first. How far will it be stretched by the same force

Answers

Complete question is;

A force stretches a wire by 0.60 mm. A second wire of the same material has the same cross section and twice the length.

a) How far will it be stretched by the same force?

b) A third wire of the same material has the same length and twice the diameter as the first. How far will it be stretched by the same force?

Answer:

0.15 mm

Explanation:

According to Hooke's Law,

E = Stress(σ)/Strain(ε)

Where E is youngs modulus

Formula for stress is;

Stress(σ) = Force(F)/Area(A)

Formula for strain is;

Strain(ε) = Change in length/original length = (Lf - Li)/Li

We are also told that a second wire of the same material has the same cross section and twice the length.

Thus;

Rearranging Hooke's Law to get the constants on one side, we have;

F/(AE) = ε

Thus from the conditions given;

ε1 = 0.6/Li

ε2 = (Change in length)/(2*Li)

And ε1 = ε2

Thus;

0.6/Li = Change in length/(2*Li)

Li will cancel out and we now have;

Change in length = 2 × 0.6 = 1.2 mm

Finally, we are told A third wire of the same material has the same length and twice the diameter as the first.

Area of a circle;A1 = πd²/4

Now, we are told d is doubled.

Thus, new area of the new circle is;

A2 = π(2d)²/4 = πd²

Rearranging Hooke's Law,we have;

F/A = εE

Since F and E are now constants, we have;

F/E = constant = Aε

Thus;

A1(ε1) = A2(ε2)

A1 = πd²/4

e1 = 0.60/Li

A2 = πd²

e2 = Change in length/Li

Thus;

((πd²/4) × 0.6)/Li = (πd² × Change in length)/ Li

Rearranging, Li and πd² will cancel out to give;

0.6/4 = Change in length

Change in length = 0.15 mm

A foot is 12 inches and a mile is 5280I ft exactly. A centimeter is exactly 0.01m or mm. Sammy is 5 feet and 5.3tall. what is Sammy's height in inches?

Answers

Answer:

65.3 Inches tall

Explanation:

If Sammy is 5 feet and 5.3 inches tall, we simply need to convert the feet to inches, and sum the remaining inches from his height to determine his overall height in inches.

So, 5 feet = (12 inches/1foot) * (5 feet) = 60 inches

And 60 inches + 5.3 inches = 65.3 inches.

Hence, Sammy is 65.3 inches tall.

Cheers.

A 5.0-µC point charge is placed at the 0.00 cm mark of a meter stick and a -4.0-µC point charge is placed at the 50 cm mark. At what point on a line joining the two charges is the electric field due to these charges equal to zero?

Answers

Answer:

Electric field is zero at point 4.73 m

Explanation:

Given:

Charge place = 50 cm  = 0.50 m

change q1 = 5 µC

change q2 = 4 µC

Computation:

electric field zero calculated by:

[tex]E1 =k\frac{q1}{r^2} \\\\E2 =k\frac{q2}{R^2} \\\\[/tex]

Where electric field is zero,

First distance = x

Second distance = (x-0.50)

So,

E1 = E2

[tex]k\frac{q1}{r^2}=k\frac{q2}{R^2} \\\\[/tex]

[tex]\frac{5}{x^2}=\frac{4}{(x-50)^2} \\\\[/tex]

x = 0.263 or x = 4.73

So,

Electric field is zero at point 4.73 m

A balloon contains 1.21 x 105 L of ideal gas at 265K. The gas is then cooled to 201 K. What is the volume (L) assuming no gas enters or exits the balloon

Answers

Answer:

The new volume will be 0.918 x 10^5 L

Explanation:

initial volume  [tex]V_{1}[/tex] = 1.21 x 10^5 L

Initial temperature [tex]T_{1}[/tex] = 265 K

Final volume [tex]V_{2}[/tex] = ?

Final temperature [tex]T_{2}[/tex] = 201 K

Th gas is an ideal gas.

For ideal gases, the equation [tex]V_{1}[/tex]/[tex]T_{1}[/tex] = [tex]V_{2}[/tex]/[tex]T_{2}[/tex] = constant

substituting value, we have

(1.21 x 10^5)/265 = [tex]V_{2}[/tex]/201

[tex]V_{2}[/tex] =  24321000/265 = 91777.4 L

= 0.918 x 10^5 L

A spring is hung from the ceiling. When a block is attached to its end, it stretches 2.5 cm before reaching its new equilibrium length. The block is then pulled down slightly and released. What is the frequency of oscillation?

Answers

Answer:

0.99Hz

Explanation:

Using F= -mx ( spring force)

At equilibrium the gravitational force will be balanced by the spring force so mg= kx

K= mg/ 0.25 N/m

But

Frequency f= 1/2pi √g/0.25

Frequency is 0.99Hz

The block is pulled down slightly and released so, Frequency of oscillation is 3.15 Hz

Frequency of oscillation based problem:

What information do we have?

Length starched = 2.5 cm

F = Kx

We know that

F = mg

So,

mg = Kx

K/m = g/x

[tex]f=\frac{1}{2\pi}\sqrt{\frac{g}{x} }\\f=\frac{1}{2\pi}\sqrt{\frac{9.8}{0.025} }[/tex]

Frequency of oscillation = 3.15 Hz

Find out more information about 'Oscillation'.

https://brainly.com/question/16016711?referrer=searchResults


I MIND TRICK PLZ HELP LOL
Troy and Abed are running in a race. Troy finishes the race in 12 minutes. Abed finishes the race in 7 minutes and 30 seconds. If Troy is running at an average speed of 3 miles per hour and speed varies inversely with time, what is Abed’s average speed for the race?

Answers

Answer:

Explanation:

Let the race be of a fixed distance x

[tex]Average Speed = \frac{Total Distance}{Total Time}[/tex]

Troy's Average speed = 3 miles/hr = x / 0.2 hr

x = 0.6 miles

Abed's Average speed = 0.6 / 0.125 = 4.8 miles/hr

What is the displacement current in the capacitor if the potential difference across the capacitor is increasing at 500,000V/s?

Answers

Answer:

[tex]I=2.71\times 10^{-5}\ A[/tex]

Explanation:

A 6.0-cm-diameter parallel-plate capacitor has a 0.46 mm gap.  

What is the displacement current in the capacitor if the potential difference across the capacitor is increasing at 500,000V/s?

Let given is,

The diameter of a parallel plate capacitor is 6 cm or 0.06 m

Separation between plates, d = 0.046 mm

The potential difference across the capacitor is increasing at 500,000 V/s

We need to find the displacement current in the capacitor. Capacitance for parallel plate capacitor is given by :

[tex]C=\dfrac{A\epsilon_o}{d}\\\\C=\dfrac{\pi r^2\epsilon_o}{d}[/tex], r is radius

Let I is the displacement current. It is given by :

[tex]I=C\dfrac{dV}{dt}[/tex]

Here, [tex]\dfrac{dV}{dt}[/tex] is rate of increasing potential difference

So

[tex]I=\dfrac{\pi r^2\epsilon_o}{d}\times \dfrac{dV}{dt}\\\\I=\dfrac{\pi (0.03)^2\times 8.85\times 10^{-12}}{0.46\times 10^{-3}}\times 500000\\\\I=2.71\times 10^{-5}\ A[/tex]

So, the value of displacement current is [tex]2.71\times 10^{-5}\ A[/tex].

Unpolarized light is passed through three successive Polaroid filters, each with its transmission axis at 45.0° to the preceding filter. What percentage of light gets through?

Answers

Answer:

The percentage is  [tex]k = 12.5 \%[/tex]

Explanation:

From the question we are told that

    The  axis is is  at  [tex]\theta = 45 ^o[/tex]

Generally the of intensity light emerging from the first polarizer is mathematically represented as

                [tex]I_{1} = \frac{I_o}{ 2}[/tex]

Where  [tex]I_o[/tex] is the intensity of unpolarized light

       Now the light emerging from the second polarizer is mathematically represented as

         [tex]I_2 = I_ 1 * cos ^2(\theta )[/tex]

         [tex]I_2 = \frac{I_o}{2} * cos ^2(45 )[/tex]

        [tex]I_2 = \frac{I_o}{2} * \frac{1}{2} = \frac{I_o}{4}[/tex]

  Now the light emerging from the third  polarizer is mathematically represented as      

       [tex]I_3 = I_ 2 * cos ^2(\theta )[/tex]

       [tex]I_3 = \frac{I_o}{4} * cos ^2(45 )[/tex]

      [tex]I_3 = \frac{I_o}{8}[/tex]

Now the percentage of the intensity of light that emerged with respect to the intensity of  the unpolarized light is

      [tex]k = \frac{\frac{I_o}{8} }{I_o } * 100[/tex]

     [tex]k = 12.5 \%[/tex]

       

The percentage of light that gets through the three successive Polaroid filters is; 12.5%

We are given;

Angle of transmission axis; θ = 45°

Formula for intensity of light from first polarizer is;

I₁ = ¹/₂I₀

Formula for intensity of light from second polarizer is;

I₂ = I₁cos²θ

Formula for intensity of light from third polarizer is;

I₃ = I₂cos²(90 - θ)

Combining the 3 equations;

Put ¹/₂I₀ for I₁ in second formula to get;

I₂ = ¹/₂I₀cos²θ

Put ¹/₂I₀cos²θ for I₂ in third formula to get;

I₃ = ¹/₂I₀cos²θ*cos²(90 - θ)

Plugging in 45° for θ gives;

I₃ = ¹/₂I₀cos²45*cos²(90 - 45)

⇒ I₃ = ¹/₂I₀cos²45*cos²45

⇒ I₃ = ¹/₂I₀cos⁴45

Now, cos 45 in surd form is 1/√2. Thus;

I₃ = ¹/₂I₀(1/√2)⁴

I₃ = ¹/₂I₀(¹/₄)

I₃ = ¹/₈I₀

I₃/I₀ = ¹/₈

I₃/I₀ = 0.125

In percentage form, we have;

I₃/I₀ = 12.5%

Read more about unpolarized light at; https://brainly.com/question/1444040

The sentence, "The popcorn kernels popped twice as fast as the last batch," is a(n) _____. experiment hypothesis observation control

Answers

The correct answer is C. Observation

Explanation:

An observation is a statement a describes a phenomenon, which is the result of measuring the phenomenon or using the senses to collect information about it. Additionally, observations are part of the Scientific method because through observations it is possible to understand phenomena.

The sentence presented is an observation because this statement is the result of the researcher observing or measuring how fast kernels pops, which means the statement derives from studying a phenomenon. Also, this cannot be classified as a hypothesis because a hypothesis is a probable explanation, and it cannot be classified as an experiment because the experiment is the general method to prove or disprove a hypothesis.

A small helium-neon laser emits red visible light with a power of 5.40 mW in a beam of diameter 2.30 mm.

Required:
a. What is the amplitude of the electric field of the light? Express your answer with the appropriate units.
b. What is the amplitude of the magnetic field of the light?
c. What is the average energy density associated with the electric field? Express your answer with the appropriate units.
d. What is the average energy density associated with the magnetic field? Express your answer with the appropriate units.

E) What is the total energy contained in a 1.00-m length of the beam? Express your answer with the appropriate units.

Answers

Answer:

A. 990v/m

B.330x10^-8T

C.2.19x10^-6J/m³

D.1.45x10^-11J

Explanation:

See attached file

Three capacitors C1 = 10.7 µF, C2 = 23.0 µF, and C3 = 29.3 µF are connected in series. To avoid breakdown of the capacitors, the maximum potential difference to which any of them can be individually charged is 125 V. Determine the maximum energy stored in the series combination.

Answers

Answer:

E = 1336.71875 J

Explanation:

We are given;. Capacitance of Capacitor 1; C1 = 10.7 µF

Capacitor 2; C2 = 23.0 µF

Capacitor 3; C3 = 29.3 µF

Supply voltage;V = 125 V

Formula for capacitance in series is;

Capacitors in series circuit: C(eq) = 1/C(1) +1/C(2) +1/C(3) .......

Thus, equivalent capacitance is;

C(eq) = (1/10.7) + (1/23) + (1/29.3) = 0.1711 µF = 0.1711 × 10^(6) F

Now, the formula for maximum energy stored is;

E = ½ × C(eq) × V²

E = ½ × 0.1711 × 10^(-6) × 125²

E = 1336.71875 J

A motorist traveling with a constant speed of 15 m/s (about 34 mi/h) passes a school-crossing corner, where the speed limit is 0 m/s (about 22 mi/h). Just as the motorist passes, a police officer on a motorcycle stopped at the comer starts off in pursuit with constant acceleration of 3.0 m/S2. (a) How much time elapses before the officer catches up with the motorist? (b) What is the officer's speed at that point? (c) What is the total distance each vehicle has traveled at that point? Please help me

Answers

Answer:

(a) 10 s

(b) 30 m/s

(c) 150 m

Explanation:

The motorist's position at time t is:

x = 15t

The officer's position at time t is:

x = ½ (3) t² = 1.5 t²

(a) When they have the same position, the time is:

15t = 1.5 t²

t = 0 or 10 s

(b) The officer's speed is:

v = 3t

v = 30 m/s

(c) The position is:

x = 15t = 150 m

What is the answer?​

Answers

Answer: i think it is d. none of them.

Explanation: The speed of light in a vacuum is 186,282 miles per second and so when you look and the answer choices and the question it doesnt make any since.

A 3200-lb car is moving at 64 ft/s down a 30-degree grade when it runs out of fuel. Find its velocity after that if friction exerts a resistive force with magnitude proportional to the square of the speed with k

Answers

Answer:

The velocity is 40 ft/sec.

Explanation:

Given that,

Force = 3200 lb

Angle = 30°

Speed = 64 ft/s

The resistive force with magnitude proportional to the square of the speed,

[tex]F_{r}=kv^2[/tex]

Where, k = 1 lb s²/ft²

We need to calculate the velocity

Using balance equation

[tex]F\sin\theta-F_{r}=m\dfrac{d^2v}{dt^2}[/tex]

Put the value into the formula

[tex]3200\sin 30-kv^2=m\dfrac{d^2v}{dt^2}[/tex]

Put the value of k

[tex]3200\times\dfrac{1}{2}-v^2=m\dfrac{d^2v}{dt^2}[/tex]

[tex]1600-v^2=m\dfrac{d^2v}{dt^2}[/tex]

At terminal velocity [tex]\dfrac{d^2v}{dt^2}=0[/tex]

So, [tex]1600-v^2=0[/tex]

[tex]v=\sqrt{1600}[/tex]

[tex]v=40\ ft/sec[/tex]

Hence, The velocity is 40 ft/sec.

Other Questions
Consent of the client before completion of a trade made between the firm and a client must be made when A) an investment adviser will be acting in the capacity of a principal B) a broker-dealer will be acting in the capacity of a principal C) a broker-dealer will be acting as a contra party to the trade D) a broker-dealer will be acting in the capacity of an agent What does Lincoln encourage in his speech How are we supposed to find the Perimeter? A researcher wants to use a confidence interval to estimate the proportion of college students in his state who plan to vote in the 2020 presidential election. He plans to randomly sample 120 college students, and plans to construct a 95% or 99% confidence interval. Which of these confidence intervals will be wider, and why describe three major philosophical theories of law (1) Shipping along rivers is not as popular as it once was. (2) It is done by air and trucking on interstates. (3) Rivers still provide viable routes for shipping, but it is no longer the most feasible method for moving materials. (4) As rivers declined in popularity, other shipping methods took their place as the best ways to ship merchandise. Which sentence lacks a logical transition? Which of the following is a specific variant of a character? A.) A Class B.) A Trait C.) A Species What steps are needed for word to create an index If two firecrackers produce a sound level of 81 dBdB when fired simultaneously at a certain place, what will be the sound level if only one is exploded? What is the oppisite of 0.7? how do you find the area of an open cylinder... what is the Formula?? please help When Jack was hired in 2011 at Ford Motor Company, he was offered $14 an hour. His best friend Sam started at the same plant doing the same job two years earlier making $28 an hour. This is an example of HURRY !!! PLEASE HELP!! Kellianne lined up the interior angles of the triangle along line p below.Which statements are true for line p? Check all that apply.It is a straight line with a measure of 360.It stays the same even if the angles in the triangle change.The line will not be straight if one of the angles in the triangle is changed to an obtuse angle.The line is only straight when one of the angles is a right angle.It represents the sum of the measures of the interior angles of the triangle.The line will not be straight if all the angles in the triangle are acute.It combines the three interior angles of the triangle to form a straight line.It is a straight line with a measure of 180 el deposito de gasolina en una estacion de servicio alcanza para 5 dias si se venden 1400 galones diarios cuantos galones diarios deben venderse para que el deposito cura 7 dias? A company sold equipment that originally cost $290,000 for $145,000 cash. The accumulated depreciation on the equipment was $145,000. The company should recognize a: Solve the equation for x. x+5-3=4 Math Question (10 Points): Lourdes hadn't bothered to study for the essay exam, joking that her motto was "fake it til you make it." Now as she stared in horror at the test booklet, the blank pages were doing the laughing, knowing she had no answers. What kind of figurative language is used? When arterial blood pressure falls the body compensates to raise the blood pressure. Explain this process. Figure ABCD is a rectangle Find the value of x