Answer:
0.165TeslaExplanation:
The Force experienced by the wire in the uniform magnetic field is expressed as F = BILsin∝ where;
B is the magnetic field (in Tesla)
I is the current (in amperes)
L is the length of the wire (in meters)
∝ is the angle that the conductor makes with the magnetic field.
Given parameters
L = 0.56 m
I = 2.6A
F = 0.24N
∝ = 90°
Required
magnitude of the magnetic field (B)
Substituting the given values into the formula given above we will have;
F = BILsin∝
0.24 = B * 2.6 * 0.56 sin90°
0.24 = B * 2.6 * 0.56 (1)
0.24 = 1.456B
1.456B = 0.24
Dividing both sides by 1.456 will give;
1.456B/1.456 = 0.24/1.456
B ≈ 0.165Tesla
Hence the magnitude of the magnetic field is approximately 0.165Tesla
When an LRC series circuit is driven at resonance, which of the following statements about the circuit are correct? (There may be more than one correct choice.)a) The impedance of the circuit has its minimum value.b) The inductive reactance and the capacitive reactance are exactly equal to each other.c) The impedance of the circuit is zero.d) The inductive reactance and the capacitive reactance are both zero.e) The impedance of the circuit has its maximum value.
Answer:
Answers a) and b) should be marked as correct.
Explanation:
Recall that the resonance in an LRC circuit occurs when the current through the circuit is at its maximum, and such takes place when the impedance (Z) of the circuit reaches its maximum. This means that the impedance (see formula below) is at its minimum value:
[tex]Z=\sqrt{R^2+(\omega\,L-\frac{1}{\omega\,C})^2 }[/tex]
as per the impedance expression above, such happens when the term in parenthesis inside the root which contains the inductive reactance ([tex]\omega\,L[/tex]) and the capacitive reactance ([tex]1/\omega\,C[/tex]) have the same value.
Therefore, answers:
a) "The impedance of the circuit has its minimum value."
and
b) "The inductive reactance and the capacitive reactance are exactly equal to each other."
are correct answers.
(a) The impedance of the circuit has its minimum value.
(b) The inductive reactance and the capacitive reactance are exactly equal to each other
LRC series circuit consists of inductor, resistor and capacitor is series.
The impedance of the circuit is calculated as follows;
[tex]Z = \sqrt{R^2 + (X_C -X_L)^2}[/tex]
where;
R is the resistance[tex]X_C[/tex] is the capacitive reactance[tex]X_L[/tex] is the inductive reactanceThe impedance of the circuit is minimum when the capacitive reactance is equal to the inductive reactance.
[tex]X_C = X_L \\\\Z = \sqrt{R^2 \ + (0)^2} \\\\Z = R[/tex]
Learn more here:https://brainly.com/question/17330472
Using a conventional two-slit apparatus with light of wavelength 605 nm, 34 bright fringes per centimeter are observed on a screen 3.1 m away. What is the slit separation
Answer:
d = 6.38 x 10⁻³ m = 6.38 mm
Explanation:
Since, the no. of bright fringes is 34 in a centimeter, therefore, the fringe spacing must be equal to:
Fringe Spacing = Δx = 1 cm/34
Δx = 0.0294 cm = 2.94 x 10⁻⁴ m
But, the formula for fringe spacing in a double slit experiment is:
Δx = λL/d
where,
λ = wavelength of light = 605 nm = 6.05 x 10⁻⁷ m
L = Distance between screen and slits = 3.1 m
d = slit separation = ?
Therefore,
2.94 x 10⁻⁴ m = (6.05 x 10⁻⁷ m)(3.1 m)/d
d = (18.755 x 10⁻⁷ m²)/(2.94 x 10⁻⁴ m)
d = 6.38 x 10⁻³ m = 6.38 mm
The maximum gauge pressure in a hydraulic system is 15 atm. What is the largest mass that could be lifted by this system if the diameter of the piston is 65 cm
Answer:
The maximum force that can be lifted by this system is 51,478.4 kg
Explanation:
Given;
maximum gauge pressure of the hydraulic system, Hp = 15 atm = 1.52 x 10⁶ N/m²
diameter of the piston, d = 65 cm = 0.65 m
The maximum gauge pressure of the piston is given as;
[tex]Hp = \frac{F}{A}[/tex]
Where;
F is the maximum force of the piston
A is the area of the piston
[tex]A = \pi (\frac{0.65}{2} )^2\\\\A = 0.3319 \ m^2[/tex]
F = Hp x A
F = 1.52 x 10⁶N/m² x 0.3319m²
F = 504488 N
Force is given as;
F = mg
m = F/g
m = 504488/9.8
m = 51,478.4 kg
Therefore, the maximum force that can be lifted by this system is 51,478.4 kg
3 QUESTIONS PLEASE ANSWER!
Answer:
1. A
2. C
3. D
Explanation:
A fish in a flat-sided aquarium sees a can of fish food on the counter. To the fish's eye, the can looks to be 43 cmcm outside the aquarium.
Required:
What is the actual distance between the can and the aquarium?
Answer:
The actual distance is [tex]d_a = 0.3233\ m[/tex]
Explanation:
From the question we are told that
The distance of the can is d = 43 cm = 0.43 m
Generally the actual distance is mathematically represented as
[tex]d_a = [\frac{ n_a }{n_w} ]* d[/tex]
Where [tex]n_a , n_w[/tex] are the refractive index of air and water and their value is
[tex]n_a = 1 , \ \ \ n_w = 1.33[/tex]
So
[tex]d_a = [\frac{ 1 }{1.33} ]* 0.43[/tex]
[tex]d_a = 0.3233\ m[/tex]
Experiments are performed with ultracold neutrons having velocities of 7.54 m/s. (a) What is the wavelength (in nm) of such a neutron
Answer:
λ = 52.5 nm
Explanation:
De Broglie's duality principle states that all matter has wave and particle characteristics, being related by the expression
p = h / λ
where the moment
p = mv
λ = h / mv
let's calculate
λ = 6.63 10⁻³⁴ / 1.675 10⁻²⁷ 7.54
λ = 5.25 10⁻⁸ m
Let's reduce anm
λ = 5.25 10⁻⁸ m (10⁹ nm / 1m)
λ = 52.5 nm
An electron moving at 3.94 103 m/s in a 1.23 T magnetic field experiences a magnetic force of 1.40 10-16 N. What angle does the velocity of the electron make with the magnetic field? There are two answers between 0° and 180°. (Enter your answers from smallest to largest.)
Answer:
10.4⁰ and 169.6⁰Explanation:
The force experienced by the moving electron in the magnetic field is expressed as F = qvBsinθ where;
q is the charge on the electron
v is the velocity of the electron
B is the magnetic field strength
θ is the angle that the velocity of the electron make with the magnetic field.
Given parameters
F = 1.40*10⁻¹⁶ N
q = 1.6*10⁻¹⁹C
v = 3.94*10³m/s
B = 1.23T
Required
Angle that the velocity of the electron make with the magnetic field
Substituting the given parameters into the formula:
1.40*10⁻¹⁶ = 1.6*10⁻¹⁹ * 3.94*10³ * 1.23 * sinθ
1.40*10⁻¹⁶ = 7.75392 * 10⁻¹⁹⁺³sinθ
1.40*10⁻¹⁶ = 7.75392 * 10⁻¹⁶sinθ
sinθ = 1.40*10⁻¹⁶/7.75392 * 10⁻¹⁶
sinθ = 1.40/7.75392
sinθ = 0.1806
θ = sin⁻¹0.1806
θ₁ = 10.4⁰
Since sinθ is positive in the 1st and 2nd quadrant, θ₂ = 180-θ₁
θ₂ = 180-10.4
θ₂ = 169.6⁰
Hence, the angle that the velocity of the electron make with the magnetic field are 10.4⁰ and 169.6⁰
The elastic limit of an alloy is 5.0×108 N/m2. What is the minimum radius rmin of a 4.0 m long wire made from the alloy if a single strand is designed to support a commercial sign that has a weight of 8000 N and hangs from a fixed point? To stay within safety codes, the wire cannot stretch more than 5.0 cm.
Answer:
4.5x 10^ -9m
Explanation:
See attached file
Answer:
The radius is [tex]r_{min} = 0.00226 \ m[/tex]
Explanation:
From the question we are told that
The elastic limit(stress) is [tex]\sigma = 5.0*10^{8} \ N /m^2[/tex]
The length is [tex]L = 4.0 \ m[/tex]
The weight of the commercial sign is [tex]F_s = 8000 \ N[/tex]
The maximum extension of the wire is [tex]\Delta L = 5.0 \ cm = 0.05 \ m[/tex]
Generally the elastic limit of an alloy (stress) is is mathematically represented as
[tex]\sigma = \frac{ F_s }{ A }[/tex]
Where A is the cross-sectional area of the wire which is mathematically represented as
[tex]A = \pi r^2[/tex]
here [tex]r = r_{min}[/tex] which is the minimum radius of the wire that support the commercial sign
So
[tex]\sigma = \frac{ F_s }{ \pi r_{min}^2 }[/tex]
=> [tex]r_{min} = \sqrt{\frac{F_s}{\sigma * \pi} }[/tex]
substituting values
[tex]r_{min} = \sqrt{\frac{8000}{ 5.0* 10^8 * 3.142} }[/tex]
[tex]r_{min} = 0.00226 \ m[/tex]
What is the pathway of sound through fluids starting at the oval window through to dissipation of the sound waves at the round window
When a magnet moves above a conducting ladder, the currents induced in the ladder produces a magnetic field. This field interacts with the magnetic field of the magnet to produce a force that A) pulls the ladder in the direction opposite to the direction of the moving magnet. B) pulls the ladder in the same direction as the moving magnet. C) brakes the ladder. D) None of the above.
Answer:
) pulls the ladder in the direction opposite
Explanation:
This is in line with lenz law that states that the magnetic field induced in a conductor act to oppose the magnetic field that produced it
a body accelerate uniformly from rest at the rate of 3meters per seconds for 8 sec . calculate the distance covered by the body during the acceleration
SOL
Answer:
96 m
Explanation:
Given:
v₀ = 0 m/s
a = 3 m/s²
t = 8 s
Find: Δx
Δx = v₀ t + ½ at²
Δx = (0 m/s) (8 s) + ½ (3 m/s²) (8 s)²
Δx = 96 m
At what minimum angle will you get total internal reflection of light traveling in diamond and reflected from ethanol? °
Answer:
34°
Using the relation
θᶜ = sin^-1(n₂/n₁),
where n1= the refractive index of light is propagating from a medium
And n2 = refractive index of medium into which light is entering
So we know that
refractive index of diamond at 589nm = 2.41= n₁
refractive index of ethanol at 589nm and 20°C = 1.36= n₂
Thus. θᶜ = sin^-1(1.361/2.417) = 0.58radians = 34°
Explanation:
: A spaceship is traveling at the speed 2t 2 1 km/s (t is time in seconds). It is pointing directly away from earth and at time t 0 it is 1000 kilometers from earth. How far from earth is it at one minute from time t 0
Answer:
145060km
Explanation: Given that
speed = dx/dt = 2t^2 +1
integrate
x = 2/3t^3 + t + c (c is constant, x is in km, t is in second)
given that at t=0, x = 1000
so 1000 = 2/3 X (0)^3 + 0 + c
or c = 1000
So x = 2/3t^3 + t + 1000
for t = 1 min = 60s
x = 2/3 X 60^3 + 60 + 1000
x = 2/3×216000+ 1060
x = 144000+1060
= 145060km
At one minute, it will be 145060km far from the earth
Two stationary positive point charges, charge 1 of magnitude 3.25 nC and charge 2 of magnitude 2.00 nC , are separated by a distance of 58.0 cm . An electron is released from rest at the point midway between the two charges, and it moves along the line connecting the two charges.
Required:
What is the speed of the electron when it is 10.0 cm from the +3.00-nC charge?
Complete Question
Two stationary positive point charges, charge 1 of magnitude 3.25 nC and charge 2 of magnitude 2.00 nC , are separated by a distance of 58.0 cm . An electron is released from rest at the point midway between the two charges, and it moves along the line connecting the two charges.
Required:
What is the speed of the electron when it is 10.0 cm from the +3.25-nC charge?
Answer:
The velocity is [tex]v = 80.82 \ m/s[/tex]
Explanation:
From the question we are told that
The magnitude of charge one is [tex]q_1 = 3.25 nC = 3.25 *10^{-9} \ C[/tex]
The magnitude of charge two [tex]q_2 = 2.00 \ nC = 2.00 *10^{-9} \ C[/tex]
The distance of separation is [tex]d = 58.0 \ cm = 0.58 \ m[/tex]
Generally the electric potential of the electron at the midway point is mathematically represented as
[tex]V = \frac{ q_1 }{\frac{d}{2} } + \frac{ q_2}{\frac{d}{2} }[/tex]
substituting values
[tex]V = \frac{ 3.25 *10^{-9} }{\frac{ 0.58}{2} } + \frac{ 2 *10^{-9} }{\frac{ 0.58}{2} }[/tex]
[tex]V = 1.8103 *10^{-8} \ V[/tex]
Now when the electron is 10 cm = 0.10 m from charge 1 , it is (0.58 - 0.10 = 0.48 m ) m from charge two
Now the electric potential at that point is mathematically represented as
[tex]V_1 = \frac{q_1}{ 0.10} + \frac{q_2}{ 0.48}[/tex]
substituting values
[tex]V_1 = \frac{3.25 *10^{-9}}{ 0.10} + \frac{2.0*10^{-9}}{ 0.48}[/tex]
[tex]V_1 = 3.67*10^{-8} \ V[/tex]
Now the law of energy conservation ,
The kinetic energy of the electron = potential energy of the electron
i.e [tex]\frac{1}{2} * m * v^2 = [V_1 - V]* q[/tex]
where q is the magnitude of the charge on the electron with value
[tex]q = 1.60 *10^{-19} \ C[/tex]
While m is the mass of the electron with value [tex]m = 9.11*10^{-31} \ kg[/tex]
[tex]\frac{1}{2} * 9.11 *10^{-19} * v^2 = [ (3.67 - 1.8103) *10^{-8}]* 1.60 *10^{-19}[/tex]
[tex]v = \sqrt{6532.4}[/tex]
[tex]v = 80.82 \ m/s[/tex]
You plan to take your hair blower to Europe, where the electrical outlets put out 240 V instead of the 120 V seen in the United States. The blower puts out 1700 W at 120 V.Required:a. What could you do to operate your blower via the 240V line in Europe? which one is it?b. What current will your blower draw from a European outlet?c. What resistance will your blower appear to have when operated at 240 ?
Answer:
a) Connect a series resistance of 8,47 ohms
b)14,16 [A]
c) r = 10,96 ohms
Explanation:
My blower requires 120 (v) then, I have to connect a series resistor to make the nominal 240 (v) of the European voltage outlet drop to 120 (V) but at the same time keep the level of current to operate my blower
In America
P = V*I
1700 (w) = 120*I
I = 1700/120 [A]
I = 14,16 [A] current needed for the blower
In Europe
120 (v) (the drop of voltage I need) when a current of 14,16 passes through to series resistor is
V = I*R 120 = 14,16* R R = 8,47 ohms
c) P = I*r²
1700 (w) = 14,16 (A) * r²
r² = 120,06
r = 10,96 ohms
Light of wavelength 519 nm passes through two slits. In the interference pattern on a screen 4.6 m away, adjacent bright fringes are separated by 5.2 mm in the general vicinity of the center of the pattern. What is the separation of the two slits?
Answer:
The separation of the two slits is 0.456 mm.
Explanation:
Given the wavelength of light = 519 nm
The indifference pattern = 4.6 m
Adjacent bright fringes = 5.2 mm
In the interference, the equation required is Y = mLR/d
Here, d sin theta = mL
L = wavelgnth
For bright bands, m is the order = 1,2,3,4
For dark bands, m = 1.5, 2.5, 3.5, 4.5
R = Distance from slit to screen (The indifference pattern)
Y = Distance from central spot to the nth order fringe or fringe width
Thus, here d = mLR/Y
d = 1× 519nm × 4.6 / 5.2mm
d = 0.459 mm
Ultraviolet light having a wavelength of 97 nm strikes a metallic surface. Electrons leave the surface with speeds up to 3.48 × 105 m/s. What is the work function, in eV of the metal?
Answer:
12.45eVExplanation:
Before calculating the work function, we must know the formula for calculating the kinetic energy of an electron. The kinetic energy of an electron is the taken as the difference between incident photon energy and work function of a metal.
Mathematically, KE = hf - Ф where;
h is the Planck constant
f is the frequency = c/λ
c is the speed of light
λ is the wavelength
Ф is the work function
The formula will become KE = hc/λ - Ф. Making the work function the subject of the formula we have;
Ф = hc/λ - KE
Ф = hc/λ - 1/2mv²
Given parameters
c = 3*10⁸m/s
λ = 97*10⁻⁹m
velocity of the electron v = 3.48*10⁵m/s
h = 6.62607015 × 10⁻³⁴
m is the mass of the electron = 9.10938356 × 10⁻³¹kg
Substituting the given parameters into the formula Ф = hc/λ - 1/2mv²
Ф = 6.63 × 10⁻³⁴*3*10⁸/97*10⁻⁹ - 1/2*9.11*10⁻³¹(3.48*10⁵)²
Ф = 0.205*10⁻¹⁷ - 4.555*10⁻³¹*12.1104*10¹⁰
Ф = 0.205*10⁻¹⁷ - 55.163*10⁻²¹
Ф = 0.205*10⁻¹⁷ - 0.0055.163*10⁻¹⁷
Ф = 0.1995*10⁻¹⁷Joules
Since 1eV = 1.60218*10⁻¹⁹J
x = 0.1995*10⁻¹⁷Joules
cross multiply
x = 0.1995*10⁻¹⁷/1.60218*10⁻¹⁹
x = 0.1245*10²
x = 12.45eV
Hence the work function of the metal in eV is 12.45eV
Figure (3) shows a car travelling along the route PQRST in 30 minutes. What is the average speed of the car in km/hour?
Answer:
60 km/hour.
Explanation:
We'll begin by calculating the total distance traveled by the car. This is illustrated below:
Total distance traveled = sum of distance between PQRST
Total distance = 10 + 5 + 10 + 5
Total distance = 30 km
Next, we shall convert 30 mins to hour. This can obtained as follow:
Recall:
60 mins = 1 hour
Therefore,
30 mins = 30/60 = 0.5 hour.
Finally, we shall determine the average speed of the car as follow:
Distance = 30 km
Time = 0.5 hour
Speed =?
Speed = distance /time
Speed = 30/0.5
Speed = 60 km/hour
Therefore, the speed of the car is 60 km/hour.
When a mercury thermometer is heated, the mercury expands and rises in the thin tube of glass. What does this indicate about the relative rates of expansion for mercury and glass
Answer:
This means that mercury has a higher or faster expansion rate than glass
Explanation:
This is because When a container expands, the reservoir in the glass expands at the same rate as the glass. Thus, if there is something in a glass and both expand at the same rate, they have no change - but if the contents expand faster, they will fill the container to a higher level, and if the contents expand slower, they will fill the container to a lower level (relative to the new size of the container).
1.) When the acceleration is zero, what can you say about the velocity of an object?
Answer:
it is either constant or zero
Explanation:
When water freezes, it expands about nine percent. What would be the pressure increase inside your automobile engine block if the water in there froze? The bulk modulus of ice is 2.0 × 109 N/m2, and 1 ATM = 1.01 × 105 N/m2.
Answer:
The pressure increase inside the automobile engine block is 1782.18 ATM
Explanation:
Given;
the change in volume of water, ΔV = 9%
the bulk modulus of ice, K = 2 x 10⁹ N/m²
Bulk modulus is given by;
[tex]K = -V\frac{dP}{dV}[/tex]
for pressure increase in the automobile engine block, when the water in there froze;
[tex]dP = K(\frac{dV}{V} )\\\\dP = K(\frac{0.09V}{V} )\\\\dP = 0.09K\\\\dP = 0.09 (2*10^9)\\\\dP = 1.8 *10^{8} \ N/m^2\\\\dP = 1782.18 \ ATM[/tex]
Therefore, the pressure increase inside the automobile engine block is 1782.18 ATM
The pressure increase inside your automobile engine block will be 1782.18 atm. The force involved vertical to the surface of an object per unit area is pressure.
What is pressure?The force applied perpendicular to the surface of an item per unit area across which that force is spread is known as pressure.
It is denoted by P. The pressure relative to the ambient pressure is known as gauge pressure.
The given data in the problem is;
ΔV is the change in volume of water = 9%
K is the bulk modulus of ice = 2 x 10⁹ N/m²
dP is the change in the presure=?
The bulk modulus is found as;
[tex]\rm K=-V \frac{dp}{dv} \\\\[/tex]
The change in the presure is obtained as;
[tex]\rm dP = K\frac{dV}{V} \\\\ \rm dP = K\frac{0.09V}{V} \\\\ \rm dP = 0.09 K \\\\ \rm dP = 0.09 \times 2 \times 10^9 \\\\ \rm dP = 1.8 \times 10^8 \\\\ \rm dP =1782.18 \ atm[/tex]
Hence the pressure increase inside your automobile engine block will be 1782.18 atm.
To learn more about the pressure refer to the link;
https://brainly.com/question/356585
What will be the nature of the image formed from both a convex lens and a concave
lens of 20 centimeter focus distance, when the object is placed at a distance of
10 centimeters?
Answer:
Explanation:
Using the lens formula
1//f = 1/u+1/v
f is the focal length of the lens
u is the object distance
v is the image distance
For convex lens
The focal length of a convex lens is positive and the image distance can either be negative or positive.
Given f = 20cm and u = 10cm
1/v = 1/f - 1/u
1/v = 1/20-1/10
1/v = (1-2)/20
1/V = -1/20
v = -20/1
v = -20 cm
Since the image distance is negative, this shows that the nature of the image formed by the convex lens is a virtual image
For concave lens
The focal length of a concave lens is negative and the image distance is negative.
Given f = -20cm and u = 10cm
1/v = 1/f - 1/u
1/v = -1/20-1/10
1/v = (-1-2)/20
1/V = -3/20
v = -20/3
v = -6.67 cm
Since the image distance is negative, this shows that the nature of the image formed by the concave lens is a virtual image
The capacitor is originally charged. How does the current I in the ammeter behave as a function of time after the switch is closed?
1. I = 0 always.
2. I = constant, not equal to 0.
3. I increases, then is constant.
4. I instantly jumps up, then slowly decreases.
5. None of the above.
Answer:
The current in the ammeter is zero.
(1) is correct option.
Explanation:
Given that,
The capacitor is charged.
We need find the current after closed switched
We know that,
When switch is closed then the capacitor behave as a short circuit, and the all current flows through it. the current is zero.
Then, the ammeter reads zero.
Hence, The current in the ammeter is zero.
(1) is correct option.
1. Why do you see colors when you look at reflected light from a CD or DVD disk, or when you look at a soap bubble or oil film on water?
2. What do you think causes the colors on the artwork panels on the side of HLS2 (Health Sciences building) which change with time of day and the angle from which you view them?
Explanation:
1.The light reflected from the CD/DVD or soap bubble or oil film forms an interference with the surrounding light. The inference both constructive and destructive making some color appear and some disappear.
2.As light behaves as wave it will interfere differently at different angles. At certain angle it will interfere constructively and at certain angle it will interfere destructively making some color brighter and some disappear. So, at different angles the color are different.
Interference pattern is responsible for the formation of different colour when a light reflected from CD or soap bubble.
We can see colors when we look at reflected light from a CD or DVD disk, or a soap bubble or oil film on water because of the interference pattern. The colors that we see on the CD are created due to the reflection of white light from ridges in the metal. When light passes through something with many small ridges or scratches, we often see rainbow colors and interesting patterns.
These patterns are called interference patterns. White light is made up of 7 colors i.e. red, orange, yellow, green, blue, indigo, violet. The CD converts or separates the white light into 7 colors so we can conclude that interference pattern is responsible for the formation of different colour when a light reflected from CD OR soap bubble.
Learn more: https://brainly.com/question/17177523
If an electron is accelerated from rest through a potential difference of 1.60 x 102V, what is its de Broglie wavelength
Answer:
0.09 x10^-10m
Explanation:
Using wavelength=( 12.27 A)/√V
= 12.27 x 10^-10/ √1.6x10^2
= 0.09x10^-10m
how does a system naturally change over time
Answer:
The movement of energy and matter in a system differs from one system to another. On the other hand, in open system both the matter and energy move into and out of the system. Therefore, matter and energy in a system naturally change over time will decrease in entropy.
Explanation:
Answer:
Decrease in entropy
Explanation:
Various systems which exist in nature possess energy and matter that move through these system continuously. The movement of energy and matter in a system differs from one system to another.
In a closed system for example, only energy flows in and out of the system while matter does not enter or leave the system.
On the other hand, in open system both the matter and energy move into and out of the system.
The AB rope is fixed to the ground at its A end, and forms 30º with the vertical. Its other end is connected to two ropes by means of the B-ring of negligible weight. The vertical rope supports the E block and the other rope passes through the grounded articulated pulley C to join at its end to the 80 N weight block D. The inclined section of the BD rope forms 60º with the vertical one; determine the weight of the E block necessary for the balance of the system and calculate the tension in the AB rope.
Answer:
T = 80√3 N ≈ 139 N
W = 160 N
Explanation:
Sum of forces on B in the x direction:
∑F = ma
80 N sin 60° − T sin 30° = 0
T = 80 N sin 60° / sin 30°
T = 80√3 N
T ≈ 139 N
Sum of forces on B in the y direction:
∑F = ma
80 N cos 60° + T cos 30° − W = 0
W = 80 N cos 60° + T cos 30°
W = 40 N + 120 N
W = 160 N
Two motorcycles are traveling in opposite directions at the same speed when one of the cyclists blasts her horn, which has frequency of 544 Hz. The other cyclist hears the frequency as 563 Hz. If the speed of sound in air is 344 m/s, what is the speed of the motorcycles
Answer:
6ms^-1
Explanation:
Given that the frequency difference is
( 563- 544) = 19
So alsoThe wavelength of each wave is = v/f = 344 /544
and there are 19 of this waves
So it is assumed that each motorcycle has moved 0.5 of this distance
in one second thus the speed of the motorcycles will be
=> 19/2 x 344/544 = 6.0 m/s
Can anyone provide me the answer with explanation?
Answer:
the answer to your question us c honey
Answer:
C
Explanation:
This is so because different materials vary in resistance and conductance of current, heat. Metals are good conductors while none metals like rubber, plastic, glass etc are good insulators or resistors.
In a double-slit experiment using light of wavelength 486 nm, the slit spacing is 0.600 mm and the screen is 2.00 m from the slits. Find the distance along the screen between adjacent bright fringes.
Answer:
The distance is [tex]y = 0.00162 \ m[/tex]
Explanation:
From the question we are told that
The wavelength is [tex]\lambda = 486 \ nm = 486 *10^{-9} \ m[/tex]
The slit spacing is [tex]d = 0.600 \ mm = 0.60 *10^{-3} \ m[/tex]
The distance of the screen is [tex]D = 2.0 \ m[/tex]
Generally the distance along the screen between adjacent bright fringes is mathematically represented as
[tex]y = \frac{\lambda * D}{d}[/tex]
substituting values
[tex]y = \frac{ 486 *10^{-9} * 2}{0.6*10^{-3}}[/tex]
[tex]y = 0.00162 \ m[/tex]
