A step-up transformer has an input voltage of 110 V (rms). There are 100 turns on the primary and 1500 turns on the secondary. What is the output voltage?

Answers

Answer 1

Answer:

V2= 1666.6 volts

Explanation:

Given data

primary turns N1= 100 turns

secondary turns N2= 1500 turns

primary voltage V1= 110 volts

secondary voltage V2= ?

We can solve for the output voltage using the turns ration sated below

  Turns Ratio = N1 / N2 = V1 / V2

Substituting our given data into the expression we have

100/1500= 110/V2

Making V2 subject of formula we have

V2= 110/(100/1500)=  1666.6 volts

V2= 1666.6 volts

Hence the secondary voltage is 1666.6 volts


Related Questions

An ideal Diesel cycle has a compression ratio of 17 and a cutoff ratio of 1.3. Determine the maximum temperature of the air and the rate of heat addition to this cycle when it produces 140 kW of power and the state of the air at the beginning of the compression is 90 kPa and 578C. Use constant specific heats at room temperature.

Answers

Answer:

maximum temperature = 1322 k

rate of heat addition = 212 kw

Explanation:

compression ratio = 17

cut off ratio = 1.3

power produced = 140 Kw

state of air at the beginning of the compression = 90 kPa and 578 c

Determine the maximum temperature of air

attached below is the detailed solution

In order to enhance net radiation exchange between a high temperature surface and a low temperature surface in an enclosure, one should:________.
(A) polish both surfaces so that they are highly reflective
(B) paint both surfaces so that they are close to a blackbody surface

Answers

Answer: Option B

Explanation:

In order to enhance net radiation exchange between a high temperature surface and a low temperature surface in an enclosure, one should: paint both surfaces so that they are close to a blackbody surface but don't polish both surfaces so that they are highly reflective

The phase sequence of a 3-phase system for which VAN = 120 /90o V and VBN = 120 /210o V is:_______
a) bca
b) abc
c) cab
d) acb

Answers

Answer:

b. abc

Explanation:

The phase rotation and its sequence is order in which voltage is reached to their respective sources. The wave forms of a polyphase flow through AC source to the panel. The three phase system has two possible sequence which can be a-b-c or c-b-a. The correct answer is therefore b.

B1) 20 pts. The thickness of each of the two sheets to be resistance spot welded is 3.5 mm. It is desired to form a weld nugget that is 5.5 mm in diameter and 5.0 mm thick after 0.3 sec welding time. The unit melting energy for a certain sheet metal is 9.5 J/mm3 . The electrical resistance between the surfaces is 140 micro ohms, and only one third of the electrical energy generated will be used to form the weld nugget (the rest being dissipated), determine the minimum current level required.

Answers

Answer:

minimum current level required =  8975.95 amperes

Explanation:

Given data:

diameter = 5.5 mm

length = 5.0 mm

T = 0.3

unit melting energy = 9.5 j/mm^3

electrical resistance = 140 micro ohms

thickness of each of the two sheets = 3.5mm

Determine the minimum current level required

first we calculate the volume of the weld nugget

v = [tex]\frac{\pi }{4} * D^2 * l[/tex] = [tex]\frac{\pi }{4} * 5.5^2 * 5[/tex] = 118.73 mm^3

next calculate the required melting energy

= volume of weld nugget * unit melting energy

= 118.73 * 9.5 = 1127.94 joules

next find the actual required electric energy

= required melting energy / efficiency

= 1127 .94 / ( 1/3 )  = 3383.84 J

TO DETERMINE THE CURRENT LEVEL REQUIRED  use the relation below

electrical energy =  I^2 * R * T

3383.84 / R*T = I^2

3383.84 / (( 140 * 10^-6 ) * 0.3 ) = I^2

therefore  8975.95 = I ( current )

1. Two types of superchargers include

A. turbine and piston.
B. roots-type and centrifugal.
C. double- and single-acting
D. rotary and reciprocating.

Answers

The answer is b, roots type and centrifugal.

Assume you have created a class named MyClass and that is contains a private field named
myField and a nonstatic public method named myMethod(). Which of the following is
true?
a. myMethod() has access to and can use myField
b. myMethod() does not have access to and cannot use myFeild.
c. myMethod() can use myField but cannot pass it to other methods.
d. myMethod() can use myField only in myField is passed to myMethod() as a
parameter.

Answers

Answer:

a. myMethod() has access to and can use myField.

Explanation:

Logic programming is a kind of programming which is largely based on formal logic.  The statement are written in logical forms which express rules about the domain. In the given scenario the my method will have access to my field which is private field. My method non static public field can also use my field class.

A charge is distributed uniformly along a long straight wire. The electric field 2 cm from the wire is 36 N/C. The electric field 4 cm from the wire is:

Answers

Answer:

New electric field = 18 N/C

Explanation:

Given:

Length (E1) = 2 cm

New length (E2) = 4 cm

Electric field =  36 N/C

Find:

New electric field

Computation:

New electric field = 36 [2 / 4]

New electric field = 36 [1/2]

New electric field = 18 N/C

/ Air enters a 20-cm-diameter 12-m-long underwater duct at 50°C and 1 atm at a

mean velocity of 7 m/s, and is cooled by the water outside. If the average heat

transfer coefficient is 85 W/m2

°C and the tube temperature is nearly equal to the

water temperature of 5°C, determine the exit temperature of air and the rate of heat

transfer.​

Answers

Answer:

A) EXIT TEMPERATURE = 14⁰C

b) rate of heat transfer of air = - 13475.78 = - 13.5 kw

Explanation:

Given data :

diameter of duct = 20-cm = 0.2 m

length of duct = 12-m

temperature of air at inlet= 50⁰c

pressure = 1 atm

mean velocity = 7 m/s

average heat transfer coefficient = 85 w/m^2⁰c

water temperature = 5⁰c

surface temperature ( Ts) = 5⁰c

properties of air at 50⁰c and at 1 atm

= 1.092 kg/m^3

Cp = 1007 j/kg⁰c

k = 0.02735 W/m⁰c

Pr = 0.7228

v  = 1.798 * 10^-5 m^2/s

determine the exit temperature of air and the rate of heat transfer

attached below is the detailed solution

Calculate the mass flow rate

= p*Ac*Vmean

= 1.092 * 0.0314 *  7 = 0.24 kg/s

A fixed mass of saturated water vapor at 400 kpa is isothermally cooled until it is a saturated liquid. Calculate the amount of heat rejected during this process in kJ/kg.

Answers

This is the explanation

The amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

What is heat?

Heat is defined as the process of kinetic energy being transferred from an energy source to a medium or an item. These three mechanisms radiation, conduction, and convection can all transmit energy. These three modes of heat transfer are typically combined, and it often happens on its own. The heat energy can be transformed into other types of energy, such as mechanical and kinetic energy. Thermal (heat) energy is a type of energy that is produced by the movement of particles and is a component of all matter.

The process rejects a certain amount of heat, which is

-q = w + Δu

q = - w - Δu

q = - 185.5 kJ/kg - 1948.9 kJ/kg

q = 2133.4 kJ/kg

Thus, the amount of heat rejected during the process in kJ/kg is 2133.4 kJ/kg.

To learn more about heat, refer to the link below:

https://brainly.com/question/1429452

#SPJ2

"The transistor base-emitter voltage (VBE) a. increases with an increase in temperature. b. is not affected by temperature change. c. decreases with an increase in temperature. d. has no effect on collector current."

Answers

Answer:

C) Decreases with an increase in temperature

Explanation:

As the temperature of a transistor increases, the thermal runaway property of the transistor becomes more significant and the transistors, conducting more freely as a result of the rise in temperature, causes an increase in the collector current or leakage current. The transistor base-emitter voltage decreases as a result.

With increased heating due to heavy current flow, the transistor is damaged.

Where are revolved sections placed in a print? A) in between break lines B) cutting planes are used to identify their locations C) in between section lines D) stand alone

Answers

Answer:

B. Cutting planes are used to identify their locations.

Explanation:

Revolved view is a cross section view of revolved 90 degrees around a cutting plane projections. The revolved view of print will differ from a cross sectional view. It includes a line nothing the axis of revolution for the view. The correct answer is B. The revolved section in the prints has cutting planes that will be used to identify their location.

When replacing a timing belt, many experts and vehicle manufacturers recommend that all of the following should be replaced except the

A. water pump
B. camshaft oil seal(s).
C. camshalt sprocket
D. tensioner assembly

Answers

Answer:

Correct Answer:

A. water pump

Explanation:

Timing belt in a vehicle helps to ensure that crankshaft, pistons and valves operate together in proper sequence. Timing belts are lighter, quieter and more efficient than chains that was previously used in vehicles.

Most car manufacturers recommended that, when replacing timing belt, tension assembly, water pump, camshaft oil seal should also be replaced with it at same time.

Match the following light concepts
- Light is bounced back at same angle
- Light penetrates medium at different angle due to different material densities
- Light bounces at different angles in periodic grid
- Light enters medium at different angles through a grid
- Light EMF field looses one axis component
A Polarized filter
B. Transmission Diffraction
C. Classical Reflection
D. Refraction
E. Reflected Diffraction

Answers

Answer:

- Light is bounced back at same angle    (Classical Reflection)

- Light penetrates medium at different angle due to different material densities     (Refraction)

Light bounces at different angles in periodic grid     (Reflected Diffraction)

Light enters medium at different angles through a grid     (Transmission Diffraction)

- Light EMF field looses one axis component     (Polarized filter)

Explanation:

Reflection is a phenomenon in which waves (light included) bounce back from an obstacle at the same angle of incidence

Refraction is the change in the angle of a wave as it enters the interface of two media. The change in angle is due to the difference in the densities of the two media.

Reflected diffraction occurs when an optical component with a periodic grid, splits, and diffracts light into several beams travelling in different directions. The light light bounces at an angle in the periodic grid.

Transmission diffraction is dispersion a beam of various wavelengths into a spectrum of associated lines due to the principle of diffraction. In this type of diffraction, light enters medium at different angles through a grid.

Polarized filters removes one field from the incidence electromagnetic wave like light, leaving it to vibrate in only one plane.

All hermetic compressors require a crankshaft seal.
True
False

Answers

True they are ur welcome

(A) Derive planar density expressions for BCC (100) and (110) planes in terms of the atomicradius R.
(B) Compute and compare planar density values for these same two planes for molybdenum (Mo).

Answers

Answer:

Explanation:

BCC structure can also be called Body-Centred Cubic. In BCC Structure, single atom is located at every corner of the cube, and one is also located at the centre of the structure.

Each of the four cube corners through which this (110) plane travels has an atom, which it shares with four neighboring unit The percentage of the entire crystallographic plane area that is occupied by atoms is known as planar density.

What is planar density ?

The packing density of crystals is measured by planar density. A face-centered cubic unit cell's planar density may be determined by following a few straightforward procedures. Determine how many atoms are centered on a certain plane. An FCC crystal, for instance, has 2 atoms on a (1 1 0) plane.

The amount of atoms per unit area on an interest plane defines the planar density, a crucial aspect of a crystal structure.

The percentage of the entire crystallographic plane area that is occupied by atoms is known as planar density. Atomic packing factor analogs in one and two dimensions are linear and planar densities.

Thus, The center atom, however, is totally contained within the unit cell. This means that this BCC (110) plane has an equivalent of 2 atoms.

To learn more about planar density follow the link;

https://brainly.com/question/17013474

#SPJ5

After clamping a buret to a ring stand, you notice that the set-up is tippy and unstable. What should you do to stabilize the set-up

Answers

Answer:

Move the buret clamp to a ring stand with a larger base.

Explanation:

A right stand is used for titration experiments in the laboratory. It holds the burette firmly during experiments so that accurate readings can be taken.

The right stand is made up of support base, vertical stainless steel, clamp with adjustable screw that holds on to the vertical rod.

The clamp is used to hold the burette in place.

If after clamping a buret to a ring stand, you notice that the set-up is tippy and unstable, the best action will be to move the buret clamp to a ring stand with a larger base.

The larger base provides a better center of gravity and stabilises the setup

Q1) Determine the force in each member of the
truss and state if the members are in tension or
compression.
Set P1 = 10 kN, P2=15 KN​

Answers

Answer:

CD = DE = DF = 0BC = CE = 15 N tensionFA = 15 N compressionCF = 15√2 N compressionBF = 25 N tensionBG = 55/2 N tensionAB = (25√5)/2 N compression

Explanation:

The only vertical force that can be applied at joint D is that of link CD. Since joint D is stationary, there must be no vertical force. Hence the force in link CD must be zero, as must the force in link DE.

At joint E, the only horizontal force is that applied by link EF, so it, too, must be zero.

Then link CE has 15 N tension.

The downward force in CE must be balanced by an upward force in CF. Of that force, only 1/√2 of it will be vertical, so the force in CF is a compression of 15√2 N.

In order for the horizontal forces at C to be balanced the 15 N horizontal compression in CF must be balanced by a 15 N tension in BC.

At joint F, the 15 N horizontal compression in CF must be balanced by a 15 N compression in FA. CF contributes a downward force of 15 N at joint F. Together with the external load of 10 N, the total downward force at F is 25 N. Then the tension in BF must be 25 N to balance that.

At joint B, the 25 N downward vertical force in BF must be balanced by the vertical component of the compressive force in AB. That component is 2/√5 of the total force in AB, which must be a compression of 25√5/2 N.

The horizontal forces at joint B include the 15 N tension in BC and the 25/2 N compression in AB. These are balanced by a (25/2+15) N = 55/2 N tension in BG.

In summary, the link forces are ...

(25√5)/2 N compression in AB15 N tension in BC25 N tension in BF0 N in CD, DE, and EF15 N tension in CE15√2 compression in CF15 N compression in FA

_____

Note that the forces at the pins of G and A are in accordance with those that give a net torque about those point of 0, serving as a check on the above calculations.

When choosing building-construction materials, what kinds of materials would you choose, all other things being equal?

Answers

The building-construction materials are materials with a relatively large bulk modulus, would the choose of the constructor. Thus, option (e) is correct.

What is building?

The term building refers to the large structure of the bricks. The building was the large structure made by the engineer and the architecture. There was the building are the people are the stay. The building was the used in the permanent basis. There are the different types of the building.

According to the building-construction materials are the engineers to the order of the bulk in the material. The bulk level of the material is the high discount rate of the order. The large amount of the material to the used in the building-construction, that are the order in the bulk of the production.

Therefore, option (e) is correct.

Learn more about on building, here;

https://brainly.com/question/24285028

#SPJ6

Your question is incomplete, but most probably the full question was.

either materials with a large or a small bulk modulus.it doesn't matter as long as the building is not too tall.materials with a relatively small shear modulus.materials with a relatively small bulk modulus.materials with a relatively large bulk modulus.

A plate is supported by a ball-and-socket joint at A, a roller joint at B, and a cable at C. How many unknown support reactions are there in this problem?

Answers

Answer:

There are five (5) unknown support reactions in this problem.

Explanation:

A roller joint rotates and translates along the surface on which the roller rests. The resulting reaction force is always a single force that is perpendicular to, and away from, the surface. This allows the roller to move in a single plane along the surface where it rests.

A cable support provides support in one direction, parallel, and in opposite direction to the load on it. There exists a single reaction from the cable pointed upwards.

A ball-and-socket joint have  reaction forces in all 3 cardinal  directions. This allows it to move in the x-y-z plane.

The total unknown reactions on the member are five in number.

Tech A says that a transistor has a single P–N junction. Tech B says that a transistor is a semiconductor device used as a switch and to amplify currents. Who is correct? Group of answer choices

Answers

Answer:

Both Technician A and technician B are correct.

Explanation: A transistor must have a P-N junction as that is where the positive and negative charges are connected.

A transistor also can be described as a semiconductor which acts as a switch and can be used to amplify currents. Transistors are very key and vital to electronic devices especially the mobile phones in recent times, it helps to ensure that electronic systems perform optimally.

The charges in the P-N junction is controlled by the availability of Positive and negative electrons.

Assume a regulator has a percent load regulation of 0.5%. What is the output voltage at full-load if the unloaded output is 12.0 V

Answers

Answer:

  11.94 V

Explanation:

Generally the regulated voltage drops as load increases. When the voltage has dropped by 0.5%, it will be 60 mV less than the nominal value:

  12.0 V - 0.06 V = 11.94 V . . . . full load voltage

An AC generator supplies an rms voltage of 120 V at 50.0 Hz. It is connected in series with a 0.650 H inductor, a 4.80 μF capacitor and a 301 Ω resistor.
(a) What is the impedance of the circuit?
(b) What is the rms current through the resistor?
(c) What is the average power dissipated in the circuit?
(d) What is the peak current through the resistor?
(e) What is the peak voltage across the inductor?
(f) What is the peak voltage across the capacitor?
The generator frequency is now changed so that the circuit is in resonance. What is that new (resonance) frequency?

Answers

Answer:

Explanation:

f = 50.0 Hz, L = 0.650 H, π = 3.14

C = 4.80 μF, R = 301 Ω resistor. V = 120volts

XL = wL = 2πfL

= 2×3.14×50* 0.650

= 204.1 Ohm

Xc= 1/wC

Xc = 1/2πfC

Xc = 1/2×3.14×50×4.80μF

= 1/0.0015072

= 663.48Ohms

1. Total impedance, Z = sqrt (R^2 + (Xc-XL)^2)= √ 301^2+ (663.48Ohms - 204.1 Ohm)^2

√ 90601 + (459.38)^2

√ 90601+211029.98

√ 301630.9844

= 549.209

Z = 549.21Ohms

2. I=V/Z = 120/ 549.21Ohms =0.218Ampere

3. P=V×I = 120* 0.218 = 26.16Watt

Note that

I rms = Vrms/Xc

= 120/663.48Ohms

= 0.18086A

4. I(max) = I(rms) × √2

= 0.18086A × 1.4142

= 0.2557

= 0.256A

5. V=I(max) * XL

= 0.256A ×204.1

=52.2496

= 52.250volts

6. V=I(max) × Xc

= 0.256A × 663.48Ohms

= 169.85volts

7. Xc=XL

1/2πfC = 2πfL

1/2πfC = 2πf× 0.650

1/2×3.14×f×4.80μF = 2×3.14×f×0.650

1/6.28×f×4.8×10^-6 = 4.082f

1/0.000030144× f = 4.082×f

1 = 0.000030144×f×4.082×f

1 = 0.000123f^2

f^2 = 1/0.000123048

f^2 = 8126.922

f =√8126.922

f = 90.14 Hz

The plate is made of steel having a density of 7910 kg/m3 .If the thickness of the plate is 9 mm , determine the horizontal and vertical components of reaction at the pin A and the tension in cable BC.

Answers

Answer:

Horizontal component ( Ax) = 0

vertical component ( Ay ) = 1794.87 N

Explanation:

Attached below is the detailed solution and the free body diagram of the question

given data:

density = 7910 kg/m3

thickness of plate = 9 mm = 0.009

determine the horizontal and vertical components of the reaction at the pin A and the tension in the cable BC

What's the resistance in a circuit that has a voltage of 60 V and a current of 2 A? A. 10 Ω B. 60 Ω C. 120 Ω D. 30 Ω

Answers

Answer:

D.  Resistance = 30 ohms

Explanation:

Using Ohm's law

V = I times R

Given:

V = 60 V

I = 2 A

Resistance = V / I = 60 V / 20 A

Resistance = 30 ohms

According to the building-up principle or aufbau principle, which subshell is typically filled next after the 3d subshell? A) 4p B) 5f C) 6p D) 5d E) 3p

Answers

According to the building-up principle or Aufbau principle, the subshell is typically filled next after the 3d subshell is the 4p subshell. The correct option is A).

What are subshells?

A subshell is the collection of states within a shell that are indicated by the azimuthal quantum number, l. S, P, D, and F subshells are represented by the values l = 0, 1, 2, and 3, respectively.

The formula for the maximum number of electrons that can fit into a subshell is 2(2l + 1). The highest level of probability for an electron to occur is in an atomic orbital.

The route that electrons travel while navigating the restrictions of the shell is referred to as a subshell. There are four different subshell classifications. The letters s, p, d, and f are used to identify the subshells.

Therefore, the correct option is A) 4p.

To learn more about subshells, refer to the link:

https://brainly.com/question/4177923

#SPJ5

A cruise missile under test is moving horizontally at Ma =2 in the atmosphere at an elevation of 2000 m (Air temperature is 2 °C). Determine the half-angle "alpha" of the Mach cone.

Answers

Answer: the half-angle "alpha" of the Mach cone = 30⁰

Explanation:

To calculate the  half-angle "alpha" of the Mach cone.

we say ;

Sin∝ = 1 / Ma

given that Ma = 2

now we substitute

Sin∝ = 1 / 2

Sin∝ = 0.5

∝ = Sin⁻¹ 0.5

∝ = 30⁰

Therefore, the half-angle "alpha" of the Mach cone is 30⁰

Which of the following sentences is
punctuated incorrectly?

Answers

Answer:

Um is there suppose to be a picture with the sentences on

Answer:

It's B I did the test and I was right on B

Explanation:

I don't know I knew it was B

how to build a laser pointer?

Answers

Answer:

It's easier to buy one, but you can search for a tutorial on how to make one on Yuotube.

There are quite a few videos on how to make one.

In a series motor, the field electromagnet consists of A) a winding connected in parallel with the armature. B) a winding connected in parallel with the armature and a second winding connected in series with the armature. C) a winding connected in series with the armature. D) a winding connected in series with a separate dc power source.

Answers

Answer:

C) a winding connected in series with the armature.

Explanation:

In a series motor, an electromagnet is used as a stator to generate its magnetic field. The field coil of this stator are connected through a commutator in series with the rotor windings. This stator which is the armature windings will conduct AC even on a DC machine, due to the  periodically reverses current direction (commutation) or due to electronic commutation (as in brushless DC motors).

Consider the thermocouple and convection conditions of Example 1, but now allow for radiation exchange with the walls of a duct that encloses the gas stream. If the duct walls are at 400℃ and the emissivity of the thermocouple bead is 0.9, calculate the steady-state temperature of the junction

Answers

Answer:

hello your question has some missing part attached below is the complete question

answer : steady state temperature = 419.713k ≈ 218.7⁰c

              Time required to reach a junction ≈ 5 secs

Explanation:

The detailed solution of the given problem is attached below but the solution to the subsequent problem from which the question you asked is referenced to( problem 1 ), is not attached because it was not part of the question you asked

Other Questions
Use distributive property to simplify the following expression. 2(4+9w) Vermeer was a representative of which style of painting?A. MannerismB. Genre artC. International GothicO D. Rococo describe the character of Lencho in the light of his aAttitude towards God and manCLASS 10 ENGLISH CHAPTER 1 LETTER TO GOD Which is the best definition of mathematical proof? a/A sequence of statements that demonstrates the truth of an assertion. b/Statements that show the assertion is false using a counterexample. c/A paragraph that always has three parts and shows that an assertion is true. d/Statements in any order that show that an assertion is true. Fuller bought 4 cantaloupes at the grocery store. Each cantaloupe weighed between 4.5 and 6.3 pounds. Fuller estimates a reasonable weight of all the cantaloupes to be 21.2 pounds. If x = 7, what is the value of 4(x - 5) PLEASE HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! The voucher system of control: Multiple Choice Is a set of procedures and approvals designed to control cash receipts and the acceptance of obligations. Establishes procedures for verifying, approving, and recording obligations for eventual cash disbursement. Establishes procedures for receiving checks for the sale of verified, approved, and recorded activities. Applies only when multiple purchases are made from the same supplier. Is required in large companies but not beneficial for small to mid-sized companies. Help me filling the blanks using correct preposition.Iam confused in A and B optionsa] The children are playing ______the tree.b] There is a bicycle ______ the children.c] There are three apples ____the table.d] There is a dog _______ the table.e] Some birds are flying ____the sky. Metals and energy currency futures contracts are actively traded on Group of answer choices propane. gold. All of the options are correct. gold and silver. silver. HELP ASAP!!!! Read the text and choose the option with the correct answer for the question. Hola! Me llamo Vanessa y soy de Texas. Hoy es el 12 de diciembre y estoy en mi dormitorio con muchas maletas porque la prxima semana voy a visitar a mi amiga Miriam y a conocer a su familia. Vamos a ir de excursin por su pas, Ecuador, y despus a explorar los pases de Chile y Per. Esta noche voy a hacer mis maletas y a preparar mi viaje a Sudamrica. En diciembre en Texas hace fro y viento, pero en Ecuador, Per y Chile hace sol y calor porque es verano. En mi maleta voy a poner camisas, unos vestidos, mi traje de bao, mis chanclas, mis tenis y claro mis gafas de sol! Pero tambin voy a empacar mis botas, unos pantalones, un abrigo y un gorro porque tambin vamos a escalar y explorar las montaas de los Andes. Miriam dice que vamos a visitar Guayaquil y Salinas en Ecuador, y Trujillo, Per y Copiap, Chile. Voy a consultar el mapa y ver unos videos por internet para saber un poco ms sobre mis destinos. Mi mam est un poco nerviosa, pero yo estoy muy emocionada! Based on the text, what element of the narrative is Miriam? Tema Protagonista Escenario Personaje Section AMultiple ChoiceRead the questions carefully and draw a circle around the letter of the correct answer.1. Where were these ceramic figures of a Bactrian camel and groom once placed?A. in the palaces of Chinese emperorsB. in the huts of poor villagersC. in the tombs of wealthy aristocrats or merchantsD. in the homes of wealthy aristocrats or merchantsEnglish Metal 1 has a larger work function than metal 2. Both are illuminated with the same short-wavelength ultraviolet light. Do electrons from metal 1 have a higher speed, a lower speed, or the same speed as electrons from metal 2? Explain. A swap bank Group of answer choices (A) can act as a broker, bringing together counterparties to a swap. (B) can act as a dealer, standing ready to buy and sell swaps. (C) both (A) and (B). (D) only sometimes (A) but never ever (B). In October, Vaughn Company reports 21,200 actual direct labor hours, and it incurs $118,830 of manufacturing overhead costs. Standard hours allowed for the work done is 23,300 hours. The predetermined overhead rate is $4.95 per direct labor hour. Compute the total overhead variance. Describe how the graph of y= x2 can be transformed to the graph of the given equation. y = (x - 13)2 + 6 At what speed, as a fraction of c, will a moving rod have a length 65% that of an identical rod at rest Match each political leader to the correct Latin American country. Which statement explains how a DNA mutation causes sickle-cell anemia?(1 point) What is the solution to the system of equations? -2x-3y+z=-6, z=6, 3x-y+z=13