A pipe branches symmetrically into two legs of length L, and the whole system rotates with angular speed ω around its axis of symmetry. Each branch is inclined at angle α to the axis of rotation. Liquid enters the pipe steadily, with zero angular momentum, at volume flow rate Q. The pipe diameter, D, is much smaller than L. Obtain an expression for the external torque required to turn the pipe. What additional torque would be required to impart angular acceleration ω_ ?

Answer:

A fan pushes hot air out of a vent and into a room. The hot air displaces cold air in the room, causing the cold air to move closer to the floor.

The hot air displacing the cold air is an example of  transfer by

Explanation:

Answer:

t = 2.94 x 10⁶ years

Explanation:

The equation used in the case of constant speed is:

s = vt

t = s/v

where,

s = distance = 12 light years

s = (12 light years)(9.461 x 10¹² km/light year) =  113.532 x 10¹² km

v = speed = 440 km/hr

t = time passed = ?

Therefore,

t = (113.532 x 10¹² km)/(440 km/hr)

t = 2.58 x 10¹¹ hr

Now, converting it to years:

t = (2.58 x 10¹¹ hr)(1 year/8766 hr)

t = 2.94 x 10⁶ years

Answer:

Option A, Sea Breeze

Explanation:

Ssea breeze is a wind that blows from the ocean or any water body to the nearby land mass. This breeze is cold as compared to the air on land. The water in water bodies has high specific heat capacity and hence takes longer time to cool as compared to the surrounding objects. The warmer air over the land rises upward thereby reducing the pressure on land and hence the sea breeze starts flowing from region of high pressure (i.e above the water body) towards the low pressure region that is the land.

Hence, option A is correct

Answer:

The thickness of the door is 0.4230 m

Explanation:

Given;

mass of bullet, m = 0.009 kg

initial velocity of the bullet, u = 803 m/s

final velocity of the bullet, v = 617 m/s

average resistive force of the door on the bullet, F = 5620 N

Apply Newton's second law of motion;

Force exerted by the door on the bullet = Force of the moving bullet

F = ma

where;

F is applied force

m is mass

a is acceleration

Also, Force exerted by the door on the bullet = Force of the moving bullet

[tex]F =ma, \ But \ a =\frac{dv}{dt} = \frac{u-v}{t} \\\\F = \frac{m(u-v)}{t}[/tex]

where;

v is the final velocity of the bullet

u is initial velocity of the bullet

t is time

We need to calculate the time spent by the bullet before it passes through the door.

[tex]t = \frac{m(u-v)}{F} \\\\t = \frac{0.009(803-617)}{5620} = 0.0002979 \ s[/tex]

Distance traveled by the bullet within this time period = thickness of the door

This distance is equivalent to the product of average velocity and time

[tex]S = (\frac{u+v}{2}) t[/tex]

where;

s is the distance traveled

[tex]S = (\frac{u+v}{2}) t\\\\S = (\frac{803+617}{2}) 0.0002979\\\\S = 0.4230 \ m[/tex]

Therefore, the thickness of the door is 0.4230 m

Answer: A. Balloons can be filled with air.

C. Air has mass.

Explanation:

Learn more https://brainly.com/question/3238218

Balloons are able to be filled with air and air has mass.

Answer:

The current pass the [tex]R_2[/tex] is  [tex]I = 0.25 A[/tex]

Explanation:

The diagram for this question is shown on the first uploaded image  

From the question we are told that

    The voltage  is  [tex]V = 3V[/tex]

     The first resistance is  [tex]R_1 = 7 \Omega[/tex]

     The second resistance is  [tex]R_2 = 5 \Omega[/tex]

Since the resistors are connected in series their equivalent resistance is  

       [tex]R_{eq} = R_1 +R_2[/tex]

Substituting values

         [tex]R_{eq} = 7 + 5[/tex]

         [tex]R_{eq} = 12 \Omega[/tex]

Since the resistance are connected in serie the current passing through the circuit  is the same current passing through [tex]R_2[/tex] which is mathematically evaluated as

        [tex]I = \frac{V}{R_{eq}}[/tex]

Substituting values  

      [tex]I = \frac{3}{12}[/tex]

      [tex]I = 0.25 A[/tex]

Answer:

Groups and culture helps in influencing our values,ethics and beliefs. This influence should always be questioned through the process of thinking critically.

This best summarizes the relationship between groups and culture and critical thinking.

Answer:

Question 3: 2.25 watts

Question 4: 405 joules

Explanation:

question 3:

Current =0.5 amps

Voltage =4.5 volts

Power= current x voltage

Power=0.5 x 4.5

power=2.25 watts

Question 4

Current =0.5 amps

Voltage =4.5v

Time=3 minutes

Time =3x60

Time =180 seconds

Energy=current x voltage x time

Energy =0.5 x 4.5 x 180

Energy =405 joules

Answer:

There will be no change in the angular momentum of the system.

Explanation:

Total angular momentum of the system  will remain unchanged . We can apply law of conservation of momentum because no external torque is acting on the system . There is increase in the momentum of inertia due to dropping of ball of putty . In order to conserve angular momentum , the system decreases its angular velocity . Hence the final angular momentum remains unchanged .  

Answer:

L= 276.4 mm

Explanation:

Given that

E= 180 GPa

d= 3.7 mm

F= 1890 N

ΔL= 0.45 mm

We know that ,elongation due to load F in a cylindrical bar is given as follows

[tex]\Delta L =\dfrac{FL}{AE}[/tex]

[tex]L=\dfrac{\Delta L\times AE}{F}[/tex]

Now by putting the values in the above equation we get

[tex]L=\dfrac{0.45\times 10^{-3}\times \dfrac{\pi}{4}\times (3.7\times 10^{-3})^2\times 108\times 10^9}{1890}\ m[/tex]

L=0.2764 m

L= 276.4 mm

Therefore the length of the specimen will be 276.4 mm

Answer:

The angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].

Explanation:

Initial angular speed of a CD player is 0 and final angular speed is 41.8 rad/s. Time to change the angular speed is 3 s.

It is required to find the angular acceleration. The change in angular speed of the CD player divided by time taken is called its angular acceleration. It can be given by :

[tex]a=\dfrac{\omega_f-\omega_i}{t}\\\\a=\dfrac{41.8-0}{3}\\\\a=13.94\ rad/s^2[/tex]

So, the angular acceleration of CD player is [tex]13.93\ rad/s^2[/tex].

Answer:

b) 20 kJ

Explanation:

Efficiency of carnot engine = (T₁ - T₂ ) / T₁  Where T₁ is temperature of hot source  and T₂ is temperature of sink .

T₁ = 270 + 273 = 543K

T₂ = 50 + 273 = 323 K

Putting the given values of temperatures

efficiency = (543 - 323) / 543

= .405

heat input = 50 KJ

efficiency = output work / input heat energy

.405 = output work / 50

output work = 20.25 KJ.

= 20 KJ .

Answer:

Electron

Explanation:

Because electron are not hadrons so electron are not affected by strong force

Particles that can not be affected by strong forces are electrons.

Electrons are the rotating material around the nucleus of an atomic element in orbit.

Atoms have electrostatic energy between their electrons. This force is not broken by a force as strong as nuclear power.

Strong force is a fundamental interaction of nature that acts between subatomic particles of matter.

There are four basic forces in nature:

Therefore, particles that are unaffected by strong force are electrons.

To learn more about strong force here

https://brainly.com/question/9910823

#SPJ2

Answer:

a) 1504.8 J

b) 991.76 J

c) 0J

d) 0J

Explanation:

(a) The work done by the force P on the box is given by the following formula:

[tex]W_P=Px[/tex]

P: applied force = 171N

x: distance in which the for P is applied = 8.80m

you replace the values of P and x and obtain:

[tex]W_P=(171N)(8.80m)=1504.8J[/tex]

(b) The work don by the friction force is:

[tex]W_f=F_fx=\mu N x=\mu Mg x[/tex]

μ = coefficient of kinetic friction = 0.250

M: mass of the box = 46.0kg

g: gravitational constant = 9.8 m/s^2

[tex]W_f=(0.250)(46.0kg)(9.8m/s^2)(8.80m)=991.76J[/tex]

(c) The Normal force is

[tex]N=Mg=(46.0kg)(9,8m/s^2)=450.8N[/tex]

but this force does not do work on the box because the direction is perpendicular to the direction of the force P.

[tex]W_N=0J[/tex]

(d) the same as before:

[tex]W_g=0J[/tex]

Answer:

A.  falling water

Explanation:

I got it right on Edgenuity. Good luck on your quiz.

In hydroelectric plants, water falls on turbine and makes it rotate. In generator, this mechanical energy transforms into electrical energy.

Hydroelectric power is generated by turbines that turn the potential energy of falling or swiftly flowing water into mechanical energy, which is then used to power generators. The most popular renewable energy source in the early 21st century was hydroelectricity, which in 2019 accounted for more than 18% of the world's total power producing capacity.

Water is gathered or stored at a higher elevation during the production of hydroelectric power and then transported through substantial pipes or tunnels (penstocks) to a lower elevation; the difference between these two elevations is referred to as the head. The falling water turns turbines as it nears the bottom of the pipelines. In turn, the turbines power generators, which transfer the mechanical energy of the turbines into electricity.

Learn more about  hydroelectric power here:

https://brainly.com/question/15228003

#SPJ2

Answer:

 6 m/s

Explanation:

Given that :

mass of the block   m =  200.0 g  = 200 × 10⁻³ kg

the horizontal spring constant   k  =  4500.0 N/m

position of the block (distance x) = 4.00 cm  = 0.04 m

To determine the speed the block will be traveling when it leaves the spring; we applying the  work done on the spring as it is stretched (or compressed) with the kinetic energy.

i.e [tex]\frac{1}{2} kx^2 = \frac{1}{2} mv^2[/tex]

[tex]kx^2 = mv^2[/tex]

[tex]4500* 0.04^2 = 200*10^{-3} *v^2[/tex]

[tex]7.2 =200*10^{-3}*v^{2}[/tex]

[tex]v^{2} =\frac{7.2}{200*10^{-3}}[/tex]

[tex]v =\sqrt{\frac{7.2}{200*10^{-3}}}[/tex]

v = 6 m/s

Hence,the speed the block will be traveling when it leaves the spring is  6 m/s

Answer:

The Object will immediately begin moving toward the left

Explanation:

Because the force of thirteen is greater than ten and applied to the opposite side

Answer:

Explanation:

Let v₁ and v₂ be velocities at lowest and topmost position . Let r be the radius of the circle .

Let N₁ and N₂ be the normal reaction force .

At the top position

centripetal force = N₂ + mg ;  so

N₂ + mg  = m v₂² / r

At the bottom  position

centripetal force = N₁ - mg ;  so

N₁ - mg  = m v₁² / r

subtracting these two equations

N₁ - mg - N₂ - mg = m v₁² / r  - m v₂² / r

N₁ - N₂ - 2mg = 1/r (m v₁²   - m v₂²  )

N₁ - N₂ - 2mg = 1/r x mg x 2r  ( loss of potential energy = gain of kinetic energy )

N₁ - N₂ =  2mg +  2mg

= 4 mg .

Answer:

Mercury is rocky

Explanation:

Answer:

Rocky

Explanation:

It has no atmosphere so it cannot hold gas.

Answer:

v_max = (1/6)e^-1 a

Explanation:

You have the following equation for the instantaneous speed of a particle:

[tex]v(t)=ate^{-6t}[/tex]   (1)

To find the expression for the maximum speed in terms of the acceleration "a", you first derivative v(t) respect to time t:

[tex]\frac{dv(t)}{dt}=\frac{d}{dt}[ate^{-6t}]=a[(1)e^{-6t}+t(e^{-6t}(-6))][/tex]  (2)

where you have use the derivative of a product.

Next, you equal the expression (2) to zero in order to calculate t:

[tex]a[(1)e^{-6t}-6te^{-6t}]=0\\\\1-6t=0\\\\t=\frac{1}{6}[/tex]

For t = 1/6 you obtain the maximum speed.

Then, you replace that value of t in the expression (1):

[tex]v_{max}=a(\frac{1}{6})e^{-6(\frac{1}{6})}=\frac{e^{-1}}{6}a[/tex]

hence, the maximum speed is v_max = ((1/6)e^-1)a

Answer:

Explanation:

We shall use Ampere's circuital law to find magnetic field at required point.

The point is outside the circumference of two given wires so whole current will be accounted for .

Ampere's circuital law

B = ∫ Bdl = μ₀ I

line integral will be over circular path of radius r = 41 cm .

Total current  I  = 5A -3A = 2A .

∫ Bdl = μ₀ I

2π r B = μ₀ I

2π x .41  B = 4π x 10⁻⁷ x 2

B = 2 x 10⁻⁷ x 2 / .41

= 9.75 x 10⁻⁷ T . It will be along - ve Y - direction.

Answer:

-7.23 rad/s

Explanation:

Given that

Mass of the cockroach, m = 0.157 kg

Radius of the disk, r = 14.9 cm = 0.149 m

Rotational Inertia, I = 5.92*10^-3 kgm²

Speed of the cockroach, v = 2.92 m/s

Angular velocity of the rim, w = 3.89 rad/s

The initial angular momentum of rim is

Iw = 5.92*10^-3 * 3.89

Iw = 2.3*10^-2 kgm²/s

The initial angular momentum of cockroach about the axle of the disk is

L = -mvr

L = -0.157 * 2.92 * 0.149

L = -0.068 kgm²/s

This means that we can get the initial angular momentum of the system by summing both together

2.3*10^-2 + -0.068

L' = -0.045 kgm²/s

After the cockroach stops, the total inertia of the spinning disk is

I(f) = I + mr²

I(f) = 5.92*10^-3 + 0.157 * 0.149²

I(f) = 5.92*10^-3 + 3.49*10^-3

I(f) = 9.41*10^-3 kgm²

Final angular momentum of the disk is

L'' = I(f).w(f)

L''= 9.41*10^-3w(f)

Using the conservation of total angular momentum, we have

-0.068 = 9.41*10^-3w(f) + 0

w(f) = -0.068 / 9.41*10^-3

w(f) = -7.23 rad/s

Therefore, the speed of the lazy Susan after the cockroach stops is -7.23 and is directed in the opposite direction of the initial lazy Susan angular speed

b)

The mechanical energy of the cockroach is not converted as it stops

Answer:

Explanation:

The problem is based on Newton's law of cooling .

According to Newton's law

dQ / dt = k ( T - T₀ ) ,

dT / dt = k' ( T - T₀ )          ; dT / dt is rate of fall of temperature.

T is average  temperature of hot body , T₀ is temperature of surrounding .

In the first case rate of fall of temperature = (210 - 191) / 2.5

= 7.6 degree / s

average temperature T = (210 + 191) /2

= 200.5  

Putting in the equation

7.6 = k' ( 200.5  - 64 )

k' = 7.6 / 136.5

= .055677

In the second case :---

In the second case, rate of fall of temperature = (191 - 156) / t  

= 35 / t   , t is time required.

average temperature T = (156 + 191) /2

= 173.5  

Putting in the equation

35 / t = .05567 ( 173.5 - 64 )

t = 5.74 minute .

Answer:147 joules

Explanation:

Mass=m=5kg

Acceleration due to gravity=g=9.8m/s^2

Height=h=3 meter

Potential energy=m x g x h

Potential energy=5 x 9.8 x 3

Potential energy=147 joules

Answer: R.A.M

Explanation:

Answer:

Check the explanation

Explanation:

Kindly check the attached image below to see the step by step explanation to the question above.

Answer:

Answer: the true statement form the given statements is “the athletes is not doing any work because he does not move weight”

Explanation:

The athlete isn’t doing any work because he doesn’t move the weight is the correct statement.

Here ,

Hence there is no work done by the athlete

Therefore ,The athlete isn’t doing any work because he doesn’t move the weight is the correct statement

Learn more about Work done here

https://brainly.com/question/25573309

#SPJ2

Answer:

Total internal reflection (TIR) is the phenomenon that involves the reflection of all the incident light off the boundary. TIR only takes place when both of the following two conditions are met: the light is in the more dense medium and approaching the less dense medium.

Explanation: Hope i helped!!!