A piece of coaxial cable has 75ohms Characteristics impedance and a nominal capacitance of 69pF/m. what is its inductance per meter ? If the diameter of the inner conductor is 0.584mm, and the dielectric constant of the insulation is 2.23, what is the outer diameter of the conductor ?​

Answers

Answer 1

Answer:

A) L = 0.388 μm

B) D = 3.78 mm

Explanation:

We are given;

Characteristics impedance; Z_o = 75 ohms

Nominal capacitance; C = 69pF/m = 69 × 10^(-12) F/m

dielectric constant; k = 2.23

Inner diameter of conductor; d = 0.584 mm

A) Now formula for Characteristics impedance is given as;

Z_o = √(L/C)

Where L is the inductance per metre.

Making L the subject, we have;

L = (Z_o)²C

L = 75² × 69 × 10^(-12)

L = 0.388 × 10^(-6) m

L = 0.388 μm

B) To get the outer diameter, we will use the formula;

Z_o = (138/√k) log(D/d)

Where;

D is outer diameter.

Thus, Plugging in the relevant values;

75 = (138/√2.23) × log (D/0.584)

log (D/0.584) = 0.81158611538

(D/0.584) = 10^(0.81158611538)

D/0.584 = 6.48016576435

D = 6.48016576435 × 0.584

D = 3.78 mm


Related Questions

Which statement describes the relay between minerals and rocks ?

Answers

Answer:

•○●□■hey hi!■□●○•

Explanation:

Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.

☆♡hope this helps♡☆

The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of 5 KN. Find the diameter of bolt required according to I. Maximum principal stress theory; 2. Maximum shear stress theory; 3. Maximum principal strain theory, 4. Maximum strain energy theory, and 5 Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson's ratio = 0.3​

Answers

Answer:

hey. its a big question. solved from *c hegg

Explanation:

Which of the following conditions were present in over 80% of paddling fatalities from 1995-2000?

Answers

Answer:

80% of the people that were killed weren't wearing a safety flotation device ( in correct terminology Personal Flotation Device, or PFD )

Explanation:

Hence they drowned due to the lack of safety.

The condition present in over 80% of paddling fatalities is that the victims were said to be not wearing a personal flotation device (PFD).

What is paddling in the sea?

The act of paddling is known to be a sport or something one can do for fun or for games.

Conclusively, a lot of paddling fatalities 1995-2000 was due to the fact that the people who were engage in the sport or act were not putting on  a personal flotation device (PFD) and this can lead to death or drowning.

Learn more about  paddling fatalities from

https://brainly.com/question/3787626

A O.1m³ rigid tank contains steam initially as 500k pa and 200°C. The steam is now allowed to cool until the temperature drops to 50°C. Determine the amount of heat transfer during the process and the final pressure in the tank​

Answers

Answer:

Check it out here

Explanation:

what the different methods to turn on thyrister and how can a thyrister turned off​

Answers

Answer:

forward voltage triggering

temperature triggering

dv/dt triggering

light triggering

gate triggering

Then turning off;

Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals

Explanation:

hope it helps

To avoid a possible collision with a manned airplane, you climb your unmanned aircraft to yield the right of way. In doing so, your unmanned aircraft reached an altitude greater than 600 feet AGL. To whom must you report the deviation?

Answers

Answer:

you have to report to the federal aviation administration upon request

Explanation:

An unmanned aircraft can also be a drone it is an aircraft that does not have passengers or a human pilot.

Such an aircraft could be fully autonomous but most times they have a human pilot who controls it remotely.

Now you have to report this deviation to the federal aviation administration. This body is responsible for the enforcement of regulations that have to do with the manufacture, operation and maintenance of aircrafts. The body makes sure there is an efficient and safe system for a navigation and they also control air traffic.

what does mean setbacks with MRT station?

Answers

The term “setback” refers to the distance (measured in feet) a house or structure must be from the front, side and rear property lines. Setbacks allow for access to underground utilities and distance between properties.

Flat plate collector can provide temperature upto_____​

Answers

Answer:

80⁰C

Explanation:

80°C.

Normal flat plate collectors can deliver heat at temperatures up to 80°C. Deficiency rates for normal flat plate collectors can be classified as visual losses, which produce with cumulative angles of the incident sunshine, and thermal losses, which upsurge fast with the working temperature intensities

Question in Statistics and Probability 2

Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
 
State the Null and the Alternative Hypotheses. 

Answers

I have this questions For a confidence level of 80% with a sample size of 21, find the critical t value answer key then u can help?

Magnetic particle testing can be done only on metals that can be magnetized.
True or false

Answers

the answer to this it true

True or false: You can create a network with two computers.



Answer
True

Answers

To create a computer network, you must have at least two computers. ... A protocol is a standard set of rules and procedures for the control of communications in a network. TRUE. Two computers using TCP/IP can communicate even if they are based on different hardware and software platforms. So your right :)

Hope this helps :)
True u must use two computers

Rafel knows that lessons learned is a valuable aid to future projects. When should he and his team address
lessons learned on a project?
Select an answer:
Add lessons learned as a topic in status meetings
Review past lessons learned so a new one does not have to be created,
Create lessons learned at the end of the project.
Brainstorm lessons learned at the beginning of a project

Answers

Answer: Create lessons learned at the end of the project.

Explanation:

Lessons learned are the experiences that are gotten from a project which should be taken into account for the future projects. Lesson learned are created at the end of the project.

The main objective of the lessons learned is that they show both the positive experience and the negative experience of a project and this will help the future projects that will be undertaken.

I want to explain what 2000 feet looks like to young children so that they can imagine it in class

Answers

Answer:

maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."

Explanation:

sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.

8.50 nC of charge is uniformly distributed along a thin rod of length L = 9.20 cm, which is then bent into a semicircle. What is the magnitude of the electric field at the center of the circle​

Answers

The answer would be 8.65

an atom that gained an electron is called​

Answers

Answer:

Hey mate......

Explanation:

This is ur answer.....

When an atom gains/loses an electron, the atom becomes charged, and is called an ion.

Hope it helps!

Brainliest pls!

Follow me :)

An atom that gained an electron is called an ION.

A steel component with ultimate tensile strength of 800 MPa and plane strain fracture toughness of 20 MPam is known to contain a tunnel (internal) crack of length 1.4 mm. This alloy is being considered for use in a cyclic loading application for which the design stresses vary from 0 to 410 MPa. Would you recommend this alloy for this application

Answers

Complete question:

A steel component with a tensile strength of 800 MPa and fracture toughness Kic=20 MPa Nm is known to contain internal cracks (also called tunnel cracks) with the maximum length of 1.4 mm. This steel is being considered for use in a cyclic loading application for which the designed stresses vary from 0 to 420 MPa. Would you recommend using this steel in this application?

a. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

b. Yes, this because the tensile strength of steel is much higher than the applied highest stress of 420 MPa.

c. Yes, this because the calculated critical stress to fracture for the cracks is higher than the highest applied stress of 420 MPa and the steel can withstand the stress of 420 MPa.

d. No. Although the calculated critical stress to fracture for the cracks is slightly higher than the highest applied stress of 420 MPa and the steel may withstand the static stress of 420 MPa, the cyclic loading may cause rapid fatigue fracture.

Answer:

A. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.

Explanation:

we are not sure if to recommend this alloy for this application given that this material has already been left to experience fatigue degradation. the cyclic load application brings about a growth in the crack. We know that cyclic loading is continuous loading that is useful for the testing of fatigue. Therefore the answer to this question is option a. We cannot make recommendations except fatigue testing has been carried out.

thank you!

once scientist has asked a question conducted an investigation and analyzed the data his or hwr goalis to​

Answers

Answer:

hola

Explanation:

Explanation:

so its an question?..........

hỗ trợ mình với được không các bạn

Answers

Answer:

Explanation:

Be bop

Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?

a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions

Answers

A project is meant to achieve clearly defined goals within present constraints

The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)

a. Scope creep

The reason for the selecting the above option is as follows;

In project management, alongside work planned in a work package, authorized work to be performed can come from;

The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcome

A scope creep, however, is generally is due to the inclusion of the end

users of the project at a time that is behind schedule, insufficient analysis of

the requirements, and project complexity underestimation. and consists of

changes made after a project has commenced

A scope creep therefore, changes the amount of work to be done which

therefore alters the project timeline, and due to project, budgetary, and

end user constraints, CANNOT be a source of authorized work to be

performed

The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep

Learn more about scope creep here:

https://brainly.com/question/14061926

A 2-stage dcv that has an internal pilot does not work well (if at all) on

Answers

Answer:

i really font onow why tbh eot you

The impeller shaft of a fluid agitator transmits 20 kW at 430 rpm. If the allowable shear stress in the impeller shaft must be limited to 65 MPa, determine (a) the minimum diameter required for a solid impeller shaft. (b) the maximum inside diameter permitted for a hollow impeller shaft if the outside diameter is 36 mm. (c) the percent savings in weight realized if the hollow shaft is used instead of the solid shaft. (Hint: The weight of a shaft is proportional to its cross-sectional area.)

Answers

Given :

Power, P = 20 kW

Speed, N = 430 rpm

Allowable shear stress, τ = 65 MPa

Torque in the shaft is given by :

[tex]$P=\frac{2 \pi NT}{60}$[/tex]

[tex]$T=\frac{60 \times 20 \times 10^3}{2 \pi \times 430}$[/tex]

T = 444.37 N.m

Diameter of the solid shaft is

[tex]$d=\sqrt[3]{\frac{16 T}{\pi \tau}}[/tex]

[tex]$d=\sqrt[3]{\frac{16 \times 444.37}{3.14 \times 65}}[/tex]

[tex]$d=\sqrt[3]{34.83} $[/tex]

d = 3.265 m

d = 326.5 mm

Internal diameter of the hollow shaft is :

[tex]$\frac{T}{\frac{\pi}{32} \left( d_0^4 - d_i^4 \right)}=\frac{\tau}{d_0/2}$[/tex]

[tex]$\frac{444.37}{\frac{3.14}{32} \left( 0.036^4 - d_i^4 \right)}=\frac{65 \times 10^6}{0.036/2}$[/tex]

[tex]$\frac{444.37}{0.09 \left( 1.6 \times 10^{-6} - d_i^4 \right)}=\frac{65 \times 10^6}{0.018}$[/tex]

[tex]$\frac{7.99}{ \left( 1.6 \times 10^{-6} - d_i^4 \right)}=5850000$[/tex]

[tex]$1.3\times 10^{-6} = 1.6 \times 10^{-6} - d_i^4 \right)}$[/tex]

[tex]$d_i^4=300000$[/tex]

[tex]$d_i = 23.40$[/tex] mm

Percentage savings in the weight is given by :

Percentage saving = [tex]$\frac{W_{solid}-W_{hollow}}{W_{solid}}\times100$[/tex]

                                 [tex]$=\frac{V_{solid}-V_{hollow}}{V_{solid}}\times100$[/tex]

                                 [tex]$=\frac{d^2 - (d_0^2 - d_i^2)}{d^2} \times 100$[/tex]

                               [tex]$=\frac{(326.5)^2 - (0.036^2 - (32.40)^2)}{(326.5)^2} \times 100$[/tex]

                                 [tex]$=\frac{106602 - \left(1.29 \times 10^{-3} - 1049.76 \right)}{106602} \times 100$[/tex]

                                  [tex]$=\frac{106602 - 1049 }{106602} \times 100$[/tex]

                                  [tex]$=\frac{105553 }{106602} \times 100$[/tex]

                                  = 99.01 %

Tech A says that the voltage regulator controls the strength of the rotor s magnetic field. Tech B says that the voltage regulator is installed between the output terminal of the alternator and the positive terminal of the battery. Who is correct?

Answers

Answer:

Voltage Regulator

Technician A is correct.

Explanation:

Technician B is not correct.  The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B.  Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct.  The computer can also be used to control the output of the alternator by controlling the field current.

1) (30 pts ) Oxygen (O2) flows through a pipe, entering at at 4 m/sec at 10000 kPa, 227oC. For a pipe inside diameter of 3.0 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas

Answers

Complete Question

Nitrogen (N2) flows through a pipe, entering at at 4 m/sec at 1000 kPa, 2270C. For a pipe inside diameter of 3 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas Then using your ideal gas mass flow rate find the rate at which enthalpy enters the pipe (kJ/sec) NO Cp, Cv, k permitted

Answer:

[tex]H=9.91kJ/sec[/tex]

Explanation:

From the question we are told that:

Velocity [tex]v=4 m/sec[/tex]

Pressure [tex]P=1000kPa[/tex]

Temperature [tex]T=227 \textdegree C[/tex]

Diameter [tex]d=3cm=>0.03m[/tex]

Generally the equation for volumetric Flow Rate is mathematically given by

[tex]V_r=(\frac{\pi*d^2}{4}v)[/tex]

[tex]V_r=(\frac{\pi*(0.03)^2}{4} *4)[/tex]

[tex]V_r=0.002827m^3/s[/tex]

Generally the equation for mass Flow Rate is mathematically given by

[tex]m_r=\frac{PV_r}{RT}[/tex]

[tex]m_r=\frac{1000*0.002827}{0.297*(227+273)}[/tex]

[tex]m_r=0.019kg/sec[/tex]

Generally the equation for mass Flow Rate is mathematically given by

Using gas Table for enthalpy Value

[tex]T=500K=>h=520.75kg[/tex]

Therefore

[tex]H=mh[/tex]

[tex]H=0.019*520.75[/tex]

[tex]H=9.91kJ/sec[/tex]

. Bơm kiểu piston tác dụng đơn có áp suất p=0,64 Mpa và lưu lượng Q=3,5 l/s. Xác định tốc độ quay của trục bơm và công suất của bơm nếu biết đường kính piston D=150 mm; bán kính tay quay R=60 mm; hiệu suất thể tích của bơm là 0=0,94; hiệu suất chung của bơm b=0,80.

Answers

Answer:

not understand language

Question 1 of 8.
What should you do to drive safely in the station?
Turn on your hazard lights
Roll your windows down and turn off the radio
Maintain idle speed (below 5mph)
All of the above
Mark for follow up

Answers

Answer: all of the above

Explanation:

To drive safely in the station, the correct option is D. All of the above.

It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.

One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights

Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.

In conclusion, the correct option is D.

Read related link on:

https://brainly.com/question/18889428

A resistor has code 104 printed on it .What is the resistive value of this resistor ​

Answers

Answer:

X = 1 (1st digit in the code)

Y = 0 (2nd digit)

Z = 4 (3rd multiplier digit)

104 → 10 × 10^4 Ω

→ 10 × 10000Ω

→ 100 kΩ

resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).

Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.

When we use numbers, let's assume that we have 3 single-digit numbers abc.

So if the code in our resistor is abc, this will mean that the resistance of the resistor is:

ab×10^c Ω

Using this general rule we can see that if the code is 104, then the resistance will be:

r = 10×10^4 Ω

 = 100,000 Ω

Then we can conclude that the resistive value of this resistor is  100,000 Ω

If you want to learn more, you can read:

https://brainly.com/question/74415

A recessed luminaire bears no marking indicating that it is ""Identified for Through- Wiring."" Is it permitted to run branch-circuit conductors other than the conductors that supply the luminaire through the integral junction box on the luminaire?

Answers

Answer:

No it is not permitted

Explanation:

It is not permitted  because as per NEC 410.21 policy no other conductor is allowed to be passed through integral junction box luminaries unless such conductor supply recessed luminaries.

The marking will show that the Luminaries is of the right construction or right installation to ensure that the the conductors ( in the outer boxes ) will not be exposed to temperatures greater than the conductor rating, hence the lack of marking makes it not to be permitted.

The secondary coil of a step-up transformer provides the voltage that operates an electrostatic air filter. The turns ratio of the transformer is 41:1. The primary coil is plugged into a standard 120-V outlet. The current in the secondary coil is 1.2 x 10-3 A. Find the power consumed by the air filter.

Answers

Answer:

  5.9 watts

Explanation:

The secondary voltage is the primary voltage multiplied by the turns ratio:

  (120 V)(41) = 4920 V

The power is the product of voltage and current:

  (4920 V)(1.2·10^-3 A) = (4.92)(1.2) W = 5.904 W

The power consumed is about 5.9 watts.

You are given a pot of hot tea (350 mL) at a temperature of 85°C and a quantity of ice at -12°C. Determine the absolute minimum amount of ice you can add to the hot tea so that at equilibrium you have iced tea (ie. a very, very small amount of ice and some water). You can assume tea has the same density (1.00 g/mL) and specific heat (4190 J/kgK) as liquid water. The heat of fusion of H2O is 3.33x10^5 J/kg. The specific heat of ice is 2090 J/kgK.

Answers

Answer:

348 g

Explanation:

The heat gained by the ice equals the heat lost by the hot tea.

Also, since we require a very, very small amount of ice and some water, to still have some ice, the temperature of the hot tea has to decrease to the melting point of ice which is 0°C. So, the final temperature of the mixture is 0 °C.

So, mc(T - T') + mL = -MC(T - T") where m = mass of ice, c =  specific heat of ice = 2090 J/kgK., T = final temperature of mixture = 0 °C, T' = initial temperature of ice = -12 °C, L = heat of fusion of H2O = 3.33 × 10⁵ J/kg, M = mass of hot tea = ρV where ρ = density of tea = 1.00 g/mL and V = volume of hot tea = 350 mL. So, M = ρV = 1.00 g/mL × 350 mL = 350 g = 0.350 kg, C = specific heat of tea = 4190 J/kgK and T" = initial temperature of tea = 85 °C.

Making m subject of the formula, we have

mc(T - T') + mL = -MC(T - T")

m[c(T - T') + L] = -MC(T - T")  

m = -MC(T - T")/[c(T - T') + L]

substituting the values of the variables into the equation, we have

m = -MC(T - T")/[c(T - T') + L]

m = -0.350 kg × 4190 J/kgK(0 °C - 85 °C.)/[2090 J/kgK(0 °C. - (-12 °C)) + 3.33 × 10⁵ J/kg]

m = -1466.5 J/kK(- 85 °C)/[2090 J/kgK(0 °C + 12 °C)) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[2090 J/kgK(12 °C) + 3.33 × 10⁵ J/kg]

m = 124652.5 J/[25080 J/kg + 3.33 × 10⁵ J/kg]

m = 124652.5 J/358080 J/kg

m = 0.3481 kg

m = 348.1 g

m ≅ 348 g

So, the minimum amount of ice to be added is 348 g.

what is tracer lathe machine​

Answers

Answer: The tracer lathe is a roughing operation for the output shaft on rear wheel drive transmissions.

Explanation:

Other Questions
A 4.17 L volume of oxygen gas measured at 7.62 C is expanded to a new volume of 4.50 L. Calculate the temperature (in oC) of the gas at the higher volume, assuming no change in pressure. Review questions:How many measures are in the next song?What is the time signature?What next song starts with an incomplete measure. True or false Where can you find the missing beat? *Please help* Mrs.Click has a strawberry patch in her garden. It's border is 4/5 meters wide and 3/2 meters long. What is the area of Mrs.Clicks Garden? WHAT IS THE RIGHTAlthough I'm not a rich man...A.I'm lucky with women.B.I always get what i want.C.I travel very much.D.No wrong. What was the plum pudding atomic model 1. What did Americans fear during the 1950s, and what did the government do about it? 2. How did Americans respond to government actions? Who did they support, and what did they oppose? to saveOcopiarO hacer clicOguardarO bajar This is a list of the heights ( each nearest cm ) of 12 children150 134 136 139 131 141132 134 136 137 150 146Select the type of the data.DiscreteContinuousCategoricalQualitativechoose oneNO FAKE ANSWERS FIRST MARKED BRAINLIST if the velocity of a vehicle starting from rest reaches 5m/2s in 2seconds, is the velocity of the vehicle uniform ?explain. Use dimensional analysis to solve the following problems. Pay attention to correct use of units and correct use of significant figures in calculations. Please show work!Convert 0.2502 grams of calcium nitrate to moles. How many atoms are contained in 3.80 moles of magnesium? A probability experiment consists of rolling a fair 10-sided die. Find the probability of the event below. rolling a 10 The planning committee routinely shut down disagreement and encouraged allegiance to the leader's ideas. What is the term for this type of group dynamic In the 1908 London Olympics, the400-meter race was introduced. WyndhamHalswelle of Great Britain won with a timeof 50.0 seconds. In 1996, Michael Johnsonof the United States ran the 400-meter racewith a time of 43.18 seconds, which is thecurrent record. If they had been racingtogether, approximately how many meterswould Halswelle still have had to run afterJohnson finished the race? The thermal efficiency (in %) of a system that undergoes a power cycle while receiving 1000 kJ of energy by heat transfer from a hot reservoir at 1000 K and discharging 500 kJ of energy by heat transfer to a cold reservoir at 400 K is: What is the factor that you must rememberbefore investing that has to do with howrisky the investment is? Please help ASAP!! What is the value of x? HELP PLS!Why was Lincolns suspension of habeas corpus legally questionable?1- The Constitution forbids the suspension of habeas corpus.2- Suspension required a nationwide referendum.3- Each state decides the right to suspend habeas corpus. 4- Only Congress had the right to suspend habeas corpus. Which sentence describes a mission statement most accurately?-A mission statement describes policies-A mission statement describes a company purpose -A mission statement describes employees benefits-A mission statement describes employee right empat kepentingan dasar perluasan kuasa kepada kerajaan pada zaman dahulu Put the correct forms of the verbs into the gabs using simple present in the sentences.1. They _ at birds (to look)2. John and Ama _ hello (to say)3. He _ the laptop (to repair)4. The cat _ under tree (to sit)5. She_ the lunch bag (to forget)