A mass m = 0.6 kg is released from rest at the top edge of a hemispherical bowl with radius = 1.1 meters. The mass then slides without friction down the inner surface toward the bottom of the bowl. At a certain point of its path the mass achieves a speed v = 3.57 m/s. At this point, what angle \theta\:θ ( in degrees) does the mass make with the top of the bowl?

Answers

Answer 1

Answer:

The  angle is  [tex]\theta = 36.24 ^o[/tex]

Explanation:

From the question we are told that

    The  mass is  [tex]m = 0.6 \ kg[/tex]

     The radius is  [tex]r = 1.1 \ m[/tex]

     The speed is  [tex]v = 3.57 \ m /s[/tex]

According to  the law of energy conservation

  The  potential energy of the mass at the top is equal to the kinetic energy at the bottom i.e

      [tex]m * g * h = \frac{1}{2} * m * v^2[/tex]

 =>    [tex]h = \frac{1}{2 g } * v^2[/tex]

Here h is the vertical distance traveled by the mass  which is also mathematically represented as

      [tex]h = r * sin (\theta )[/tex]

So

     [tex]\theta = sin ^{-1} [ \frac{1}{2* g* r } * v^2][/tex]

substituting values

     [tex]\theta = sin ^{-1} [ \frac{1}{2* 9.8* 1.1 } * (3.57)^2][/tex]

     [tex]\theta = 36.24 ^o[/tex]


Related Questions

As the frequency of the ac voltage across a capacitor approaches zero, the capacitive reactance of that capacitor:_______.
a. approaches zero.
b. approaches infinity.
c. approaches unity.
d. none of the above.

Answers

Answer:

b. approaches infinity

Explanation:

Because Capacitive reactance is given as Xc = 1/ωC

So we can see that the value of capacitive reactance and therefore its overall impedance (in Ohms) decreases to zero as the frequency increases acting like a short circuit.

Same as the frequency approaches zero or DC, the capacitors reactance increases to infinity, acting like an open circuit which is why capacitors block DC

A pulley 326 mm in diameter and rotating initially at 4.00 revolutions per second receives a constant angular acceleration of 2.25 radians per second squared by a drive belt. What is the linear velocity of the belt after 5.00 seconds

Answers

Answer:

The linear velocity, v = 5.93 m/s

Explanation:

To find the linear velocity after 5 seconds, we find its angular velocity after 5 seconds using

ω' = ω + αt where ω = initial angular speed = 4.00 rev/s = 4.00 × 2π rad/s = 25.13 rad/s, ω' =  = final angular speed, α = angular acceleration = 2.25 rad/s² and t = time = 5.00 s

ω' = ω + αt

= 25.13 rad/s + 2.25 rad/s² × 5.00 s

= 25.13 rad/s + 11.25 rad/s

= 36.38 rad/s

The linear velocity v is gotten from v = rω' where r = radius of pulley = 326 mm/2 = 163 mm = 0.163 m

v = rω'

= 0.163 m × 36.38 rad/s

= 5.93 m/s

So, the linear velocity  v = 5.93 m/s

A merry-go-round spins freely when Diego moves quickly to the center along a radius of the merry-go-round. As he does this, it is true to say that

Answers

Answer:

A) the moment of inertia of the system decreases and the angular speed increases.

Explanation:

The complete question is

A merry-go-round spins freely when Diego moves quickly to the center along a radius of the  merry-go-round. As he does this, It is true to say that

A) the moment of inertia of the system decreases and the angular speed increases.

B) the moment of inertia of the system decreases and the angular speed decreases.

C) the moment of inertia of the system decreases and the angular speed remains the same.

D) the moment of inertia of the system increases and the angular speed increases.

E) the moment of inertia of the system increases and the angular speed decreases

In angular momentum conservation, the initial angular momentum of the system is conserved, and is equal to the final angular momentum of the system. The equation of this angular momentum conservation is given as

[tex]I_{1} w_{1} = I_{2} w_{2}[/tex]    ....1

where [tex]I_{1}[/tex] and [tex]I_{2}[/tex] are the initial and final moment of inertia respectively.

and [tex]w_{1}[/tex] and [tex]w_{2}[/tex] are the initial and final angular speed respectively.

Also, we know that the moment of inertia of a rotating body is given as

[tex]I = mr^{2}[/tex]    ....2

where [tex]m[/tex] is the mass of the rotating body,

and [tex]r[/tex] is the radius of the rotating body from its center.

We can see from equation 2 that decreasing the radius of rotation of the body will decrease the moment of inertia of the body.

From equation 1, we see that in order for the angular momentum to be conserved, the decrease from [tex]I_{1}[/tex] to [tex]I_{2}[/tex] will cause the angular speed of the system to increase from [tex]w_{1}[/tex] to [tex]w_{2}[/tex] .

From this we can clearly see that reducing the radius of rotation will decrease the moment of inertia, and increase the angular speed.

A semi-circular loop consisting of one turn of wire is place in the x-y plane. A constant magnetic field B=1.7T points along the negative z-axis(into the page), and a current I=0.7A flows counterclockwisefrom the positive z-axis. The net magnetic force on the circular section of the loop points in what direction? What is the net magnetice force on the circular section of the loop?

Answers

Answer:

The direction of net magnetic force on the circular section of the loop is in the positive y-axis

The net magnetic force on the circular section of the loop is 3.74 N

Explanation:

The magnetic field strength [tex]B[/tex] = 1.7 T

the current [tex]I[/tex] = 0.7 A

The diameter of the loop = 2 m

the length of the circular section of the semi-circular loop [tex]l[/tex] = πd/2

==> [tex]l[/tex] = (3.142 x 2)/2 = 3.142 m

The force on the semi-circular is given as

F = [tex]BIl[/tex] sin ∅

but the loop is perpendicular to the field, therefore

sin ∅ = sin 90° = 1

F = 1.7 x 0.7 x 3.142 x 1 = 3.74 N

The right hand rule states that "if the fingers of the right hand are held parallel to each other in the direction of the magnetic field, and the thumb is held at right angle to the other fingers in the direction of the flow of current. The palm will push in the direction of the magnetic force on the conductor".

According to the right hand rule, the direction of net magnetic force on the circular section of the loop is in the positive y-axis

Question 18(Multiple Choice Worth 2 polnis)
When riding your skateboard you crash into a curb, the skateboard stops, and you continue moving forward. Which law of
motion is being described in this scenario?
O Law of Universal Gravitation
o Newton's Second Law of Motion
o Law of Conservation of Energy
o Newton's First Law of Motion​

Answers

Last point, Newton’s first law of motion is the correct answer.

Hope this helps ya

a car moves for 10 minutes and travels 5,280 meters .What is the average speed of the car?​

Answers

Answer:use the formular distance over time i.e distance/time. Make sure to convert the distance from metres to kilometers and time from minutes to hours .

Explanation:

The average speed of the car is 31,680 meters per hour.

To calculate the average speed of the car, you need to divide the total distance traveled by the time it took to travel that distance.

Given:

Time taken (t) = 10 minutes = 10 minutes × (1 hour / 60 minutes) = 10/60 hours = 1/6 hours

Distance traveled (d) = 5,280 meters

Average Speed (v) = Distance (d) / Time (t)

Average Speed (v) = 5280 meters / (1/6) hours

To simplify, when you divide by a fraction, it's equivalent to multiplying by its reciprocal:

Average Speed (v) = 5280 meters × (6/1) hours

Average Speed (v) = 31,680 meters per hour

Hence, the average speed of the car is 31,680 meters per hour.

To know more about average speed here

https://brainly.com/question/17661499

#SPJ2

A city of Punjab has a 15 percent chance of wet weather on any given day. What is the probability that it will take a week for it three wet weather on 3 separate days? Also find its Standard Deviation

Answers

Answer:

so the probability will be = 0.062

Standard deviation =  0.8925

Explanation:

The probability of rain = 15% = 15/100= 0.15

and the probability of no rain=q = 1-p= 1-0.15= 0.85

The number of trials = 7

so the probability will be

7C3 * ( 0.15)^3 (0.85)^4= 35* 0.003375 * 0.52200 =0.06166= 0.062

Taking this as binomial as the p and q are constant and also the trials are independent .

For a binomial distribution

Standard deviation = npq= 0.15 *0.85 *7= 0.8925

3. Which of the following accurately describes circuits?
O A. In a parallel circuit, the same amount of current flows through each part of the circuit
O B. In a series circuit, the amount of current passing through each part of the circuit may vary
O C. In a series circuit, the current can flow through only one path from start to finish
O D. In a parallel circuit, there's only one path for the current to travel.

Answers

Answer:

Option (c)

Explanation:

In a Series circuit, as the components are connected end-to-end ,the current can flow through only one path from start to finish.

(C.) is the only correct statement in the list of choices.

In a series circuit, the current can flow through only one path from start to finish.

The earth has a vertical electric field at the surface,pointing down, that averages 102 N/C. This field is maintained by various atmosphericprocesses, including lightning.
What is the excess charge on the surface of the earth? inC

Answers

Answer:

[tex]q = -461532.5 \ C[/tex]

Explanation:

From the question we are told that

     The  electric filed is  [tex]E = 102 \ N/C[/tex]  

Generally according to Gauss law

=>   [tex]E A = \frac{q}{\epsilon_o }[/tex]

Given that  the electric field is pointing downward  , the equation become

    [tex]- E A = \frac{q}{\epsilon_o }[/tex]

Here   [tex]q[/tex] is the excess charge on the surface of the earth

          [tex]A[/tex] is the surface  area of the of the earth which is mathematically represented as

     [tex]A = 4\pi r^2[/tex]

Where r is the radius of the earth which has a value [tex]r = 6.3781*10^6 m[/tex]

 substituting values

    [tex]A = 4 * 3.142 * (6.3781*10^6 \ m)^2[/tex]

    [tex]A =5.1128 *10^{14} \ m^2[/tex]

So

   [tex]q = -E * A * \epsilon _o[/tex]

Here [tex]\epsilon_o[/tex] s the permitivity of free space with value

          [tex]\epsilon_o = 8.85*10^{-12} \ m^{-3} \cdot kg^{-1}\cdot s^4 \cdot A^2[/tex]

substituting values

     [tex]q = -102 * 5.1128 *10^{14} * 8.85 *10^{-12}[/tex]

     [tex]q = -461532.5 \ C[/tex]

A girl is sitting on the edge of a pier with her legs dangling over the water. Her soles are 80.0 cm above the surface of the water. A boy in the water looks up at her feet and wants to touch them with a reed. (nwater =1.333). He will see her soles as being:____

a. right at the water surface.
b. 53.3 cm above the water surface.
c. exactly 80.0 cm above the water surface.
d. 107 cm above the water surface.
e. an infinite distance above the water surface.

Answers

Answer:

d. 107 cm above the water surface.

Explanation:

The refractive index of water and air = 1.333

The real height of the girl's sole above water = 80.0 cm

From the water, the apparent height of the girl's sole will be higher than it really is in reality by a factor that is the refractive index.

The boy in the water will therefore see her feet as being

80.0 cm x 1.333 = 106.64 cm above the water

That is approximately 107 cm above the water

Light passes from a material with index of refraction 1.3 into one with index of refraction 1.2. Compared to the incident ray, what happens to the refracted ray?

Answers

Answer:

It bends away from the normal

Explanation:

From Snell's law of Refraction, when a ray passes from a medium of lower Refractive index to a medium with higher Refractive index, the Refractive ray will bend towards the normal. However, when the ray passes from a medium of higher Refractive index to a medium of lower Refractive index, the Refractive ray will bend away from the normal.

Now, from the question we are told that Light passes from a material with index of refraction 1.3 into one with index of refraction 1.2.

This means from a higher Refractive index to a lower one and from Snell's law as earlier said, the refracted ray will bend away from the normal

The refracted ray is seen to bend away from the normal.

Let us recall that an optically denser medium will have a higher refractive index. This means that the medium with a refractive index of  1.3  is the denser medium and the medium with a refractive index of  1.2 is the less dense medium.

From the statement in the question, we can boldly say that light is travelling from a denser to less dense medium given the values of the refractive index given. When light is travelling from a denser to a less dense medium, the refracted ray bends away from the normal.

Learn more: https://brainly.com/question/1445383

An electron moving in the direction of the +x-axis enters a magnetic field. If the electron experiences a magnetic deflection in the -y direction, the direction of the magnetic field in this region points in the direction of the:______

Answers

Answer:

-z axis

Explanation:

According to the left hand rule for an electron in a magnetic field, hold the thumb of the left hand at a right angle to the rest of the fingers, and the rest of the fingers parallel to one another. If the thumb represents the motion of the electron, and the other fingers represent the direction of the field, then the palm will push in the direction of the force on the electron. In this case, the left hand will be held out with the thumb pointing to the right (+x axis), and the palm facing your body (-y axis). The magnetic field indicated by the other fingers will point down in the the -z axis.

PLEASE HELP FAST Five-gram samples of brick and glass are at room temperature. Both samples receive equal amounts of energy due to heat flow. The specific heat capacity of brick is 0.22 cal/g°C and the specific heat capacity of glass is 0.22 cal/g°C. Which of the following statements is true? 1.The temperature of each sample will increase by the same amount. 2.The temperature of each sample will decrease by the same amount. 3.The brick will get hotter than the glass. 4.The glass will get hotter than the brick.

Answers

Answer:

1.The temperature of each sample will increase by the same amount

Explanation:

This is because, since their specific heat capacities are the same and we have the same mass of each substance, and the same amount of energy due to heat flow is supplied to both the glass and brick at room temperature, their temperatures would thereby increase by the same amount.

This is shown by the calculation below

Q = mcΔT

ΔT = Q/mc where ΔT = temperature change, Q = amount of heat, m = mass of substance and c = specific heat capacity of substance.

Since Q, m and c are the same for both substances, thus ΔT will be the same.

So, the temperature of each sample will increase by the same amount

ametal of mass 0.6kg is heated by an electric heater connected to 15v batter when the ammeter reading is 3A its tempeeature rises feom 20c to 85c in 10 minutes calculate the s.h.c of metal cylinder​

Answers

Answer:

692 J/kg/°C

Explanation:

Electric energy added = amount of heat

Power × time = mass × SHC × increase in temperature

Pt = mCΔT

(15 V × 3 A) (10 min × 60 s/min) = (0.6 kg) C (85°C − 20°C)

C = 692 J/kg/°C

At what speed (in m/s) will a proton move in a circular path of the same radius as an electron that travels at 7.45 ✕ 106 m/s perpendicular to the Earth's magnetic field at an altitude where the field strength is 1.10 ✕ 10−5 T

Answers

Answer:

The speed of the proton is 4059.39 m/s

Explanation:

The centripetal force on the particle is given by;

[tex]F = \frac{mv^2}{r}[/tex]

The magnetic force on the particle is given by;

[tex]F = qvB[/tex]

The centripetal force on the particle must equal the magnetic force on the particle, for the particle to remain in the circular path.

[tex]\frac{mv^2}{r} = qvB\\\\r = \frac{mv^2}{qvB} \\\\r = \frac{mv}{qB}[/tex]

where;

r is the radius of the circular path moved by both electron and proton;

⇒For electron;

[tex]r = \frac{(9.1*10^{-31})(7.45*10^6)}{(1.602*10^{-19})(1.1*10^{-5})}\\\\r = 3.847 \ m[/tex]

⇒For proton

The speed of the proton is given by;

[tex]r = \frac{mv}{qB}\\\\mv = qBr\\\\v = \frac{qBr}{m} \\\\v = \frac{(1.602*10^{-19})(1.1*10^{-5})(3.847)}{1.67*10^{-27}} \\\\v = 4059.39 \ m/s[/tex]

Therefore, the speed of the proton is 4059.39 m/s

¿Qué resistencia debe ser conectada en paralelo con una de 20 Ω para hacer una
resistencia combinada de 15 Ω?

Answers

Answer:

60 Ω

Explanation:

R(com) = 15 Ω

1/R(com) = 1/R1 + 1/R2 + 1/R3 ..... + 1/Rn

1/15 = 1/20 + 1/R2

1/R2 = 1/15 - 1/20

1/R2 = (4 - 3) / 60

1/R2 = 1/60

R2 = 60 Ω

así, la combinada de resistencia necesaria es 60 Ω

A spherical balloon has a radius of 6.95 m and is filled with helium. The density of helium is 0.179 kg/m3, and the density of air is 1.29 kg/m3. The skin and structure of the balloon has a mass of 950 kg. Neglect the buoyant force on the cargo volume itself. Determine the largest mass of cargo the balloon can lift. Express your answer to two significant figures and include the appropriate units.

Answers

volume of balloon

= 4/3 T R3

= 4/3 x 3.14 x 6.953

= 1405.47 m3

uplift force

= volume of balloon x density of air x 9.8

= = 1405.47 x 1.29 x 9.8

= 1813.05 x 9.8 N

weight of helium gas

= volume of balloon x density of helium x

9.8

= 1405.47 x .179 x 9.8

= 251.58 x 9.8 N

Weight of other mass = 930 x 9.8 N Total weight acting downwards

= 251.58 x 9.8 +930 x 9.8

= 1181.58 x 9.8 N

If W be extra weight the uplift can balance

1181.58 × 9.8 + W × 9.8 = 1813.05 * 9.8

1181.58+W=1813.05

W= 631.47 kg

Equipotential lines are lines with equal electric potential (for example, all the points with an electric potential of 5.0 V). Using the plot tool that comes with voltmeter (pencil icon) make two equipotential lines at r = 0.5 m and r = 1.5 m. Enable electric field vectors in the simulation. Put an electric field sensor at different points on the equipotential line and note the direction of the electric field vector. What can you conclude about the direction of the electric field vector in relation to the equipotential lines?

The direction for each field vector is perpendicular to equipotential lines.

Take a snapshot of the simulation showing equipotential lines and paste to a word document.

Answers

....................

Two wires carry current I1 = 73 A and I2 = 31 A in the opposite directions parallel to the x-axis at y1 = 3 cm and y2 = 13 cm. Where on the y-axis (in cm) is the magnetic field zero?

Answers

Answer:

The position on the y-axis where the magnetic field is zero is at y = 10 cm

Explanation:

The magnetic field B due to a long straight wire carrying a current, i at a distance R from the wire is given by

B = μ₀i/2πR

Now, let y be the point where the magnetic fields of both wires are equal.

So, the magnetic field due to wire 1 carrying current i₁ = 73 A is

B₁ = μ₀i₁/2π(y - 3) and

the magnetic field due to wire 2 carrying current i₂ = 31 A is

B₂ = μ₀i₂/2π(13 - y)

At the point where the magnetic field is zero, B₁ = B₂. So,

μ₀i₁/2π(y - 3) = μ₀i₂/2π(13 - y)

cancelling out μ₀ and 2π, we have

i₁/(x - y) = i₂/(13 - y)

cross-multiplying, we have

(13 - y)i₁ = (y - 3)i₂

Substituting the values of i₁ and i₂, we have

(13 - y)73 = (y - 3)31

949 - 73y = 31y - 93

Collecting like terms, we have

949 + 93 = 73y + 31y

1042 = 104y

dividing through by 104, we have

y = 1042/104

y = 10.02 cm

y ≅ 10 cm

So, the position on the y-axis where the magnetic field is zero is at y = 10 cm

A toroidal solenoid with 400 turns of wire and a mean radius of 6.0 cm carries a current of 0.25 A. The relative permeability of the core is 80.
(a) What is the magnetic field in the core?
(b) What part of the magnetic field is due to atomic currents?

Answers

Answer:

A) 0.0267 T

B) 0.0263 T

Explanation:

Given that

The number of turns, N = 400

Radius of the wire, r = 6 cm = 0.06 m

Current in the wire, I = 0.25 A

Relative permeability, K(m) = 80

See the attached picture for the calculation

A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?

Answers

Answer:

Explanation:

According to Equations of Projectile motion :

[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]

vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec

(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec

[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]

(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m

[tex]Horizontal Range = vcosx * t[/tex]

(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m

The difference between a DC and an AC generator is that
a. the DC generator has one unbroken slip ring.
b. the AC generator has one unbroken slip ring
c. the DC generator has one slip ring splitin two halves.
d. the AC generator has one slip ring split in two halves.
e The DC generator has twounbroken sip rings

Answers

Answer:

The AC generator has one unbroken slip ring

Explanation:

In physics, the application of electromagnetic induction can be seen in generators and dynamos. Electromagnetic induction is the process of generating electricity using magnets. It found applications in generators and the types of generator they found application is in AC and DC generator.

An AC generator is also called a Dynamo. A DC generator contains what is called a SPLIT RING fixed to the end of the coil which can be separated and coupled back according to the name "split". An AC generator also called a Dynamo makes use of a SLIP ring which cannot be divided into two. It comes as an entity. The presence of this rings is what differentiates a DC generator from an AC generator.

We can replace split rings with slip rings when converting a DC generator to an AC generator and vice versa.

It can therefore be concluded that the difference between a DC and an AC generator is that the AC generator has one unbroken slip ring.

The speed of sound through air is 340 m/s. If a person hears the clap of thunder 9.6 s after seeing the bolt of lightning, how far away is the lightning?

Answers

Explanation:

Distance = speed × time

d = (340 m/s) (9.6 s)

d = 3264 m

A 3200-lb car is moving at 64 ft/s down a 30-degree grade when it runs out of fuel. Find its velocity after that if friction exerts a resistive force with magnitude proportional to the square of the speed with k

Answers

Answer:

The velocity is 40 ft/sec.

Explanation:

Given that,

Force = 3200 lb

Angle = 30°

Speed = 64 ft/s

The resistive force with magnitude proportional to the square of the speed,

[tex]F_{r}=kv^2[/tex]

Where, k = 1 lb s²/ft²

We need to calculate the velocity

Using balance equation

[tex]F\sin\theta-F_{r}=m\dfrac{d^2v}{dt^2}[/tex]

Put the value into the formula

[tex]3200\sin 30-kv^2=m\dfrac{d^2v}{dt^2}[/tex]

Put the value of k

[tex]3200\times\dfrac{1}{2}-v^2=m\dfrac{d^2v}{dt^2}[/tex]

[tex]1600-v^2=m\dfrac{d^2v}{dt^2}[/tex]

At terminal velocity [tex]\dfrac{d^2v}{dt^2}=0[/tex]

So, [tex]1600-v^2=0[/tex]

[tex]v=\sqrt{1600}[/tex]

[tex]v=40\ ft/sec[/tex]

Hence, The velocity is 40 ft/sec.

Consider a wire of a circular cross-section with a radius of R = 3.17 mm. The magnitude of the current density is modeled as J = cr2 = 9.00 ✕ 106 A/m4 r2. What is the current (in A) through the inner section of the wire from the center to r = 0.5R?

Answers

Answer:

The current is  [tex]I = 8.9 *10^{-5} \ A[/tex]

Explanation:

From the question we are told that

     The  radius is [tex]r = 3.17 \ mm = 3.17 *10^{-3} \ m[/tex]

      The current density is  [tex]J = c\cdot r^2 = 9.00*10^{6} \ A/m^4 \cdot r^2[/tex]

      The distance we are considering is  [tex]r = 0.5 R = 0.001585[/tex]

Generally current density is mathematically represented as

          [tex]J = \frac{I}{A }[/tex]

Where A is the cross-sectional area represented as

         [tex]A = \pi r^2[/tex]

=>      [tex]J = \frac{I}{\pi r^2 }[/tex]

=>    [tex]I = J * (\pi r^2 )[/tex]

Now the change in current per unit length is mathematically evaluated as

        [tex]dI = 2 J * \pi r dr[/tex]

Now to obtain the current (in A) through the inner section of the wire from the center to r = 0.5R we integrate dI from the 0 (center) to point 0.5R as follows

         [tex]I = 2\pi \int\limits^{0.5 R}_{0} {( 9.0*10^6A/m^4) * r^2 * r} \, dr[/tex]

         [tex]I = 2\pi * 9.0*10^{6} \int\limits^{0.001585}_{0} {r^3} \, dr[/tex]

        [tex]I = 2\pi *(9.0*10^{6}) [\frac{r^4}{4} ] | \left 0.001585} \atop 0}} \right.[/tex]

        [tex]I = 2\pi *(9.0*10^{6}) [ \frac{0.001585^4}{4} ][/tex]

substituting values

        [tex]I = 2 * 3.142 * 9.00 *10^6 * [ \frac{0.001585^4}{4} ][/tex]

        [tex]I = 8.9 *10^{-5} \ A[/tex]

A small helium-neon laser emits red visible light with a power of 5.40 mW in a beam of diameter 2.30 mm.

Required:
a. What is the amplitude of the electric field of the light? Express your answer with the appropriate units.
b. What is the amplitude of the magnetic field of the light?
c. What is the average energy density associated with the electric field? Express your answer with the appropriate units.
d. What is the average energy density associated with the magnetic field? Express your answer with the appropriate units.

E) What is the total energy contained in a 1.00-m length of the beam? Express your answer with the appropriate units.

Answers

Answer:

A. 990v/m

B.330x10^-8T

C.2.19x10^-6J/m³

D.1.45x10^-11J

Explanation:

See attached file

Two hoops, staring from rest, roll down identical incline planes. The work done by nonconservative forces is zero. The hoops have the same mass, but the larger hoop has twice the radius. Which hoop will have the greater total kinetic energy at the bottom

Answers

Answer:

They both have the same total K.E at the bottom

Explanation:

This Is because If assuming no work is done by non conservative forces, total mechanical energy must be conserved

So

K1 + U1 = K2 + U2

But If both hoops start from rest, and and at the bottom of the incline the level for gravitational potential energy is zero for reference

thus

K1 = 0 , U2 = 0

ΔK = ΔU = m g. h

But if the two inclines have the same height, and both hoops have the same mass m,

So difference in kinetic energy, must be the same for both hoops.

"A thin film with an index of refraction of 1.50 is placed in one of the beams of a Michelson interferometer. If this causes a shift of 8 bright fringes in the pattern produced by light of wavelength 540 nm, what is the thickness of the film?"

Answers

Answer:

The film thickness is 4.32 * 10^-6 m

Explanation:

Here in this question, we are interested in calculating the thickness of the film.

Mathematically;

The number of fringes shifted when we insert a film of refractive index n and thickness L in the Michelson Interferometer is given as;

ΔN = (2L/λ) (n-1)

where λ is the wavelength of the light used

Let’s make L the subject of the formula

(λ * ΔN)/2(n-1) = L

From the question ΔN = 8 , λ = 540 nm, n = 1.5

Plugging these values, we have

L = ((540 * 10^-9 * 8)/2(1.5-1) = (4320 * 10^-9)/1 = 4.32 * 10^-6 m

A car moving at 36 m/s passes a stationary police car whose siren has a frequency of 500 Hz. What is the change in the frequency (in Hz) heard by an observer in the moving car as he passes the police car? (The speed of sound in air is 343 m/s.)

Answers

Answer:

Change in the frequency (in Hz) = 104.96 Hz

Explanation:

Given:

Speed of sound in air (v) = 343 m/s

Speed of car (v1) 36 m/s

Frequency(f) = 500 Hz

Find:

Change in the frequency (in Hz)

Computation:

Frequency hear by the observer(before)(f1) = [f(v+v1)] / v

Frequency hear by the observer(f1) = [500(343+36)] / 343

Frequency hear by the observer(f1) = 552.48 Hz

Frequency hear by the observer(after)(f2) = [f(v-v1)] / v

Frequency hear by the observer(f2) = [500(343-36)] / 343

Frequency hear by the observer(f2) = 447.52 Hz

Change in the frequency (in Hz) = f1 - f2

Change in the frequency (in Hz) = 552.48 Hz - 447.52 Hz

Change in the frequency (in Hz) = 104.96 Hz

The advantage of a hydraulic lever is A : it transforms a small force acting over a large distance into a large force acting over a small distance. B : it transforms a small force acting over a small distance into a large force acting over a large distance. C : it allows you to exert a larger force with less work. D : it transforms a large force acting over a large distance into a small force acting over a small distance. E : it transforms a large force acting over a small distance into a small force acting over a large distance.

Answers

Answer:

A) it transforms a small force acting over a large distance into a large force acting over a small distance.

Explanation:

The hydraulic lever works based on Pascal's law of transmission of pressure through a fluid. In the hydraulic lever, the pressure transmitted is the same.

Pressure transmitted P = F/A

where F is the force applied

and A is the area over which the force is applied.

This pressure can be manipulated on the input end as a small force applied over a small area, and then be transmitted to the output end as a large force over a large area.

F/A = f/a

where the left side of the equation is for the output, and the right side is for the input.

The volume of the displaced fluid will be the same on both ends of the hydraulic lever. Since we know that

volume V = (area A) x (distance d)

this means that the the piston on the input smaller area of the hydraulic lever will travel a greater distance, while the piston on the larger output area of the lever will travel a small distance.

From all these, we can see that the advantage of a hydraulic lever is that it transforms a small force acting over a large distance into a large force acting over a small distance.

Other Questions
list 2 forms of computer output On a plane trip, baggage over 40 pounds is charged at the rate per pound of 1% of the one-way fare. The charge for a bag weighing 52 pounds on a trip where the one-way fare is $98 is: Tony knew there was a solution to his math problem in one of four textbooks. He got some information from his classmates about it: Andy: "The solution is in either book 1 or 2"; Billy: "The solution is in either book 3 or 4"; Charlie: "The solution is in book 4"; Danny: "There is no solution in book 3". Emily helped Tony by saying that only one of his classmates was right, and the other three were mistaken. Which book has the solution in it? standard form of 6,32,94,000 describe classification as a work in progress discuss the characteristics of the three domains: Bacteria, Archaea, and Eukarya describe classification by cladistics summarize how molecular evidence reveals species relatedness identify the structures and shapes of viruses describe different types of viral infections please solve quick Drag each label to the correct location.Match each description to a type of primary sourcepersonal scrapbook,government census data,corporate business records,university archives-the population of the three largest cities in the US In 2010 - a picture of what junior prom dresses looked like in 1998 -the vote from a shareholders meeting in 1997 - a graph showing net profits and losses for 2003 - publications by English Department faculty members in 1963.- the number of citizens under the age 18 in 1960 - alumni association bylaws from 1989 - a ticket stub from the movie Titanic Write down the name of the shape for question D. Please help! The standard overhead applied is based on the ______ level of activity multiplied by the predetermined overhead rate. Hankins Corporation has 8.1 million shares of common stock outstanding, 300,000 shares of 4.1 percent preferred stock outstanding, par value of $100; and 185,000 bonds with a semiannual coupon rate of 5.5 percent outstanding, par value $2,000 each. The common stock currently sells for $57 per share and has a beta of 1.15, the preferred stock has a par value of $100 and currently sells for $99 per share, and the bonds have 18 years to maturity and sell for 107 percent of par. The market risk premium is 6.6 percent, T-bills are yielding 3.3 percent, and the companys tax rate is 24 percent.A. What is the firms market value capital structure?B. If the company is evaluating a new investment project that has the same risk as the firms typical project, what rate should the firm use to discount the projects cash flows?Solve for:A. DebtPreferred StockEquityB. Discount Rate pros and cons of jose balta,please help me I got a test of 21 questions leave your number if you answer them and get 80 percent on Ill pay you if you get 100 Ill pay really good On January 1, Power House Co. prepaid the annual rent of $10,140. Prepare the journal entry to record this transaction. A monopolist's maximized rate of economic profits is $1500 per week. Its weekly output is 500 units, and at this output rate, the firm's marginal cost is $32 per unit. The price at which it sells each unit is $42 per unit. At these profit and output rates, what are the firm's average total cost and marginal revenue? Simplify the radical On a coordinate plane, triangle A B C is shown. Point A is at (negative 2, negative 4), point B is at (2, negative 1), and point C is at (3, negative 4). Triangle ABC is an isosceles triangle in which side AB = AC. What is the perimeter of triangle ABC? 5 + StartRoot 10 EndRoot units 10 + StartRoot 10 EndRoot units 10 StartRoot 10 EndRoot units 50 units TB MC Qu. 9-100 The following labor standards have been ... The following labor standards have been established for a particular product: Standard labor-hours per unit of output 9.6 hours Standard labor rate $ 13.40 per hour The following data pertain to operations concerning the product for the last month: Actual hours worked 7,400 hours Actual total labor cost $ 96,200 Actual output 950 units What is the labor efficiency variance for the month Choose the best answer to the following question. Explain your reasoning with one or more complete sentences. At 11:00 you place a single bacterium in a bottle, and at 11:01 it divides into 2 bacteria, which at 11:02 divide into 4 bacteria, and so on. How many bacteria will be in the bottle at 11:30? The table shows the relationship between the cost of renting a car from the Wrecko Car Rental Company and the number of days for the rental. Draw a scatter plot and find an equation for the line of best fit. Use the equation to determine the cost of renting a car for 20 days. Days Cost 1 $44 2 $67 3 $90 4 $113 7 $182 10 $251 Hi, can anyone please help me come up with 7 maths questions that have the answer 10. It would be great if these questions were on the 8th grade level. Plz help fast.