Answer:
67.56kg
Explanation:
Fapp+mg = ma
Fapp= applied force
mg = reactional force
g = acceleration due to gravity
Where g = 9.8m/s^2 a= 5 m/s2, Fapp= 1000N.
1000N = ma + mg
1000N = m( a+g )
1000N = m ( 5+9.8)
1000N = m×14.8
m = 1000÷14.8
m = 67.56kg.
Hence the mass of the wagon will be 67.56kg
Rafael swings a baseball bat with a force of 25 N. The baseball bat exerts a force of 5 N on the baseball. What is the mechanical advantage of the baseball bat? The mechanical advantage of the baseball bat is
Answer:
0.2
Explanation:
Mechanical Advantage is defined as the ratio of force output with respect to the force input. Thus,
MA = output / input
MA = 5 / 25
MA = 1/5
MA = 0.2
Since this value is less then one. Even though it's tagged a mechanical advantage, in reality it would be mechanical disadvantage.
Therefore, we can say that the mechanical advantage of the baseball bat is 0.2
Answer:
0.2
Explanation:
Which happens during the day at the beach?
A. The water is warmer than the land, and air sinks over the water
B. The water is cooler than the land, and air sinks over the water
C. The water is warmer than the land, and air rises over the water
D. The water is cooler than the land, and air rises over the water
Answer:
c
Explanation:
not sure i think heating beach
a man is trying to move a piano by himself, but it will not move, what force must they overcome to start the piano moving?
Answer:
The friction of the piano and the weight
Explanation:
Two water waves meet at the same point, one having a displacement above equilibrium of 60 cm and the other having a displacement above equilibrium of 80 cm.
Answer:
The resultant displacement is 140 cm
Explanation:
say first displacement d₁ is 60 cm
and second displacement d₂ is 80 cm
Resultant displacement = d₁ + d₂
= 60 + 80
= 140 cm
Answer:
Explanation:
To solve this problem it will be necessary to apply the interference principle.
Under this principle interference is understood as a phenomenon in which two or more waves overlap to form a resulting wave of greater, lesser or equal amplitude. In this case, if both are at the same point, the result of the total displacement will be the sum of the individual displacements, therefore
[tex]x = \sum h_i\\\\x = 60cm + 80cm\\\\x =140cm[/tex]
Therefore the resulting displacement above equilibrium is 140cmwhy are the group 17 elements the most reactive of the nonmetal elements a)they are the biggest elements b)they have the fewest electrons c)they are located on the farthest right side of the periodic table d)they require only one electron to fill their outer energy level
Answer:
I think the answer is D-they require onky one electron to fill their outer energy level.
An air-track glider attached to a spring oscillates between the 10.0 cm mark and the 61.0 cm mark on the track. The glider completes 11.0 oscillations in 31.0 s
Answer:
T = 2.82 seconds.
The frequency [tex]\mathbf{f = 0.36 \ Hz}[/tex]
Amplitude A = 25.5 cm
The maximum speed of the glider is [tex]\mathbf{v = 56.87 \ rad/s}[/tex]
Explanation:
Given that:
the time taken for 11 oscillations is 31 seconds ;
SO, the time taken for one oscillation is :
[tex]T = \frac{31}{11}[/tex]
T = 2.82 seconds.
The formula for calculating frequency can be expressed as :
[tex]f = \frac{1}{T}[/tex]
[tex]f = \frac{1}{2.82}[/tex]
[tex]\mathbf{f = 0.36 \ Hz}[/tex]
The amplitude is determined by using the formula:
[tex]A = \frac{d}{2}[/tex]
The limits that the spring makes the oscillations are from 10 cm to 61 cm.
The distance of the glider is, d = (61 - 10 )cm = 51 cm
Replacing 51 for d in the above equation
[tex]A = \frac{51}{2}[/tex]
A = 25.5 cm
The maximum speed of the glider is:
[tex]v = A \omega[/tex]
where ;
[tex]\omega = \frac{2 \pi}{T}[/tex]
[tex]\omega = \frac{2 \pi}{2.82}[/tex]
[tex]\omega = 2.23 \ rad/s[/tex]
[tex]v = A \omega[/tex]
[tex]v = 25.5 *2.23[/tex]
[tex]\mathbf{v = 56.87 \ rad/s}[/tex]
The rigid beam is supported by the three suspender bars. bars ab and ef are made of aluminum and bar cd is made of steel. if each bar has a cross-sectional area of 450 mm2, determine the maximum value of p if the allowable stress is (σallow)st = 200 mpa for the steel and ( σallow)al = 150 mpa for the aluminum. est = 200 gpa and eal = 70 gpa.
Answer:
Pmax = 67.5 KN
Explanation:
We need to calculate the maximum allowable value of P for both aluminum and steel bars.
FOR STEEL BARS:
Since,
(σallow)st = (Pmax)st/A
where,
(σallow)st = maximum allowable stress of steel bar = 200 MPa = 2 x 10⁸ Pa
A = Cross-sectional area of steel bar = 450 mm² = 0.45 x 10⁻³ m²
(Pmax)st = Maximum allowable force for steel bar = ?
Therefore,
2 x 10⁸ Pa = (Pmax)st/0.45 x 10⁻³ m²
(Pmax)st = (2 x 10⁸ Pa)(0.45 x 10⁻³ m²)
(Pmax)st = 9 x 10⁴ N = 90 KN
FOR Aluminum BARS:
Since,
(σallow)al = (Pmax)al/A
where,
(σallow)al = maximum allowable stress of Al bar = 150 MPa = 1.5 x 10⁸ Pa
A = Cross-sectional area of Aluminum bar = 450 mm² = 0.45 x 10⁻³ m²
(Pmax)al = Maximum allowable force for Aluminum bar = ?
Therefore,
1.5 x 10⁸ Pa = (Pmax)al/0.45 x 10⁻³ m²
(Pmax)al = (1.5 x 10⁸ Pa)(0.45 x 10⁻³ m²)
(Pmax)al = 6.75 x 10⁴ N = 67.5 KN
Since,
(Pmax)al < (Pmax)st
Therefore,
The maximum allowable force will be:
Pmax = (Pmax)al
Pmax = 67.5 KN
Jenny and Fred both play a long note on their trombones. A stationary observer hears the sound increasing and decreasing repeatedly in loudness. Which of these must be true?
A.The sound waves from the two trombones have slightly different frequencies.
B. The sound waves from the two trombones have the same frequency.
C. The sound waves from the two trombones have slightly different amplitudes.
D. The sound waves from the two trombones have the same wavelength.
E. The sound waves from the two trombones have slightly different velocities.
Answer:
A.The sound waves from the two trombones have slightly different frequencies.
Explanation:
This is because, a difference in frequency of waves from two different sources would result in either constructive or destructive interference of the waves. Thereby, causing the observer to hear the sound increasing or decreasing.
Answer:
A.The sound waves from the two trombones have slightly different frequencies.
Are carbon compounds rigid and strong
This diagram shows a baseball’s motion. Which statement is best supported by the diagram?
a
Maximum Gravitational potential energy is at point R.
b
Kinetic energy becomes potential energy between points P and Q.
c
Kinetic energy becomes potential energy between points R and S.
d
Maximum kinetic energy is at point R.
Answer:
A
Explanation:
maximum gravitional potential energy is at point R
explain nuclear fusion briefly
Answer:
Nuclear fusion is the process in which two atomic nuclei are fused together into a larger single nucleus, releasing energy in the process. ... In proton-proton fusion, four hydrogen atoms are fused into a single helium-4 atom, releasing a lot of energy in the process.
Explanation:
The passage helps the reader to draw conclusions about which character's perspective? ºAlec ºAlice ºAlec's father ºAlec's mother
Answer:
I think it might be A: Alec but tell me if I'm wrong
Explanation:
Answer:
a
Explanation:
i did it on e d g e n u i t y
What is the formula for velocity???
Explanation:
divide the distance by the time it takes to travel that same distance, then add your direction to it.
Or change in displacement divided by change in time.
Se tienen 2 vectores cuyos módulos están en la misma razón que 5 y 2. Si cuando forman 53º su resultante mide 3√29u, ¿Cuánto mide el mayor vector?
Answer:
|v2| = 3.27
Explanation:
You have two vector v1 and v2. The relation between the magnitudes of both vectors is given by:
[tex]\frac{|v_1|}{|v_2|}=\frac{5}{2}[/tex]
Furthermore, the projection (the dot product) of one vector on the other one is given by the following formula:
[tex]v_1 \cdot v_2 = |v_1||v_2|cos\theta[/tex]
The dot product between v1 and v2 is 3√29. If you multiply the right hand side of the last equation by |v2|/|v2| you obtain:
[tex]3\sqrt{29}=\frac{|v_1|}{|v_2|}|v_2|^2cos(53\°)[/tex]
you do |v2| the subject of the formula:
[tex]|v_2|=\sqrt{\frac{|v_2|}{|v_1|}\frac{3\sqrt{29}}{cos53\°}}\\\\|v_2|=\sqrt{\frac{2}{5}\frac{3\sqrt{29}}{cos53\°}}=3.27[/tex]
Un semáforo de 80N cuelga del punto medio de un cable de 30m tendido entre 2 postes. Halle la tensión en cada segmento del cable si éste tiene un pandeo que lo hace descender una distancia vertical de 1m
Answer:
T1 = T2 = 602.33 N
Explanation:
I attached an image of the forces diagram below.
The x component of the forces for this cases is:
[tex]\Sigma F_x=T_1cos\theta-T_2cos\theta=0\\\\T_1cos\theta=T_2cos\theta\\\\T_1=T_2[/tex]
And the y components:
[tex]\Sigma F_y=T_1sin\theta+T_2sin\theta-W=0\\\\T_1=T_2=T\\\\\Sigma F_y=2Tsin\theta=W\\\\T=\frac{W}{2sin\theta}[/tex]
The angle is calculated by using the information about the length of the cable and the vertical distance of the traffic light:
[tex]\theta=tan^{-1}(\frac{1}{15})=3.81\°[/tex]
Thus, you obtain:
[tex]T=\frac{80N}{2(sin3.81\°)}=601.33N[/tex]
hence, the tension in both segments of the cable is 602.33 N
Which of the following are two factors that determine speed?
a. acceleration and time
b. distance and time
c. velocity and time
d. motion and time
Answer:
B) Distance and Time
Explanation:
Equation for speed: S = D / T
Speed equals the distance you traveled divided by the amount of time it took to get to that destination.
The two factors which are required to determine the speed of a object are distance traveled by it and time taken by it.
What is speed?The speed is the rate at which the total distance by a object is traveled in the time taken.
Speed of a object can be given as,
[tex]s=\dfrac{d}{t}[/tex]
Here, (d) is the distance traveled by the object and (t) is time taken but the object to cover that distance.
As the unit of the distance is measured in the meter and the time measure in the second. Thus the speed of a object is measured in the meter per second.
In the vehicles the speed of vehicle is also measured in the kilometre per hour or miles per hour.
Hence, the two factors which are required to determine the speed of a object are distance traveled by it and time taken by it.
Thus the option B is the correct option.
Learn more about the speed here;
https://brainly.com/question/359790
30
. Which of the following represents the
statement "The difference of two square
numbers is positive
Answer:
In mathematics, the difference of two squares is a squared (multiplied by itself) number subtracted from another squared number. Every difference of squares may be factored according to the identity. in elementary algebra.
Explanation:
What is motion ,terms used to measure motion ,examples etc
Answer:
A physic term
Explanation:
Answer:
Cambio de lugar o de posición de un cuerpo en el espacio.
Explanation:
How far can you get away from your little brother with a paintball marker if you can travel at 3 m/s and you have 15s before he sees you?
Heat pumps move heat from __________ to __________ areas & REQUIRES energy. *
A. cold, hot
B. hot, cold
What is the electrical power when the current is 20 amps and the voltage is 15 volts? *
A. 35 watts
B. 1.33 watts
C. 300 watts
Work is a transfer of matter. *
A. True
B. False
Which phrases describe all the outer planets’ motion? Select two options.
no rotation
fast rotation
slow revolution
opposite revolution
north to south rotation
Answer:
Fast rotation
Slow revolution
Explanation:
Solar system has 8 planets. 4 inner rocky planets - Mercury, Venus, Earth and Mars and 4 outer gaseous planets - Jupiter, Saturn, Uranus and Neptune. The outer planets have few common features.
They are gaseous. There period of revolution is larger than the inner planets which means that they have slow revolution about the Sun. One day on the outer planets is smaller than the inner planets which means they have fast rotation.
For example, Jupiter has revolves around sun in 11.86 Earth years and rotates about axis in 9.8 Earth hours. Uranus revolves around sun in 84 Earth years and rotates on its axis 17.9 Earth hours.
Answer:
Fast rotation
Slow revolution
Explanation:
did the test
Which structure connects muscles to bone?
Answer: tendons connect muscles to bones
Explanation:
An ice skater spins at 2.5 rev/s when his arms are extended. He draws his arms in and spins at 10.0 rev/s. By what factor does his moment of inertia change in the process?
Answer:
The moment of inertia decreased by a factor of 4
Explanation:
Given;
initial angular velocity of the ice skater, ω₁ = 2.5 rev/s
final angular velocity of the ice skater, ω₂ = 10.0 rev/s
During this process we assume that angular momentum is conserved;
I₁ω₁ = I₂ω₂
Where;
I₁ is the initial moment of inertia
I₂ is the final moment of inertia
[tex]I_2 = \frac{I_1 \omega_1}{\omega_2} = \frac{I_1*2.5}{10} \\\\I_2 = 0.25I_1 = \frac{1}{4}I_1[/tex]
Therefore, the moment of inertia decreased by a factor of 4
2. A new racecar track is being created, and the owners want the cars to complete 10
miles in 7 laps. What does the diameter of the track have to be to meet their
requirements?
Answer:
0.45 miles
Explanation:
since, car will be running on the edge of track, distance covered in one lap by car will be equal to circumference of track.\
we will use value of pi as 22/7
Circumference for any circular shape is given by [tex]\piD[/tex][tex]\pi D[/tex]
Hence, in one lap [tex]\pi D[/tex] distance will be covered
in 7 laps [tex]7 \pi D[/tex] distance will be covered.
but is given that 7 laps should be equal to 10 miles
so 10 miles will be equal to [tex]7\pi D[/tex]
[tex]7\pi D= 10 \ miles\\=> 7*(22/7)* D= 10 \ miles\\=> 22D = 10 \ miles\\=> D = 10/22 \ miles\\=> D = 0.45 \ miles[/tex]
Thus, diameter of track will be 0.45 miles to meet the requirement.
mix 4 L of 30°C water is 6 L of 40°C water and you’ll have water at what temperature?
Answer:
dont know
Explanation:
need points
Which energy output objects work with the turbine?
Examples of pure substances are elements and _________.
A. Mixtures
B. Compounds
Answer:
b
Explanation:
Answer:
b
Explanation:
trust
What has an ionised atom lost or gained?
Protons
Gamma Rays
Electrons
Neutrons
Answer:
Electrons
Explanation:
Ionised atoms loose and gain electrons.
hope it helps!
What causes atoms to bond together
?!?
Answer:
electrostatic attraction
Explanation:
Atoms form chemical bonds with other atoms when there's an electrostatic attraction between them. This attraction results from the properties and characteristics of the atoms' outermost electrons, which are known as valence electrons.
Choose the best definition for velocity
1. How fast something is going
2. Speed in a certain direction
3. Which direction something is going
4. Something speeding up