A fish in an aquarium with flat sides looks out at a hungry cat. To the fish, does the distance to the cat appear to be less than the actual distance, the same as the actual distance, or more than the actual distance? Explain.

Explanation:

Change in Velocity = final velocity - initial velocity

Change in velocity = 30km/h - (- 45km/h )

= 75 km/h due west

Answer:

Cardiovascular exercise is the activity use that aerobic metabolism and cellular reaction.

Explanation:

Answer:

a force that moves an object

Explanation:

the formula for work is force * distance

This question involves the concepts of work, force, and displacement.

The statement that best identifies the requirements for work to be performed is "a force that moves an object".

Work is defined as the product of force applied on an object and the distance moved by the object. Mathematically,

Work = (Force)(Displacement)

Hence, both the applied force and the displacement of the object as a result of the application of the force is necessary for the work to be done. If any one of these values becomes zero, the work automatically becomes zero, which means no work is performed.

Learn more about work here:

https://brainly.com/question/4095205

The color that is reflected when a red card is illuminated by red light is white.

The color an object is perceived to have, depends on the frequency of light it reflects.

If white light incidents on a red filter, red is transmitted while blue and green are absorbed.

Consequently, when a red card is illuminated by red light, the red card will  reflect back almost all the incident light on it, causing it to appear brighter which creates an  illusion of white color to the eyes.

Thus, we can conclude the color that is reflected when a red card is illuminated by red light is white.

Learn more here:https://brainly.com/question/3495999

Answer:

95.7v

Explanation

Using Faraday's law of electromagnetic induction we know that rate of change in magnetic flux will induce EMF in closed loop

So it is given as

E= Ndစ/dt

E= N BA-0/ deta t

Given that

N = 58turns

B = 1.10T

A = 0.150m^²

Deta t= 0.1s

now we have

E = 58(1.10x0.150)/0.1

= 95.7v

Magnetic flux is decreasing, so the direction of the current will be to aid the decreasing flux $decrease= CLOCKWISE

Explanation:

Answer:

The average power dissipated is 72 W.

Explanation:

Given;

peak voltage of the AC circuit, V₀ = 120 V

resistance of the resistor, R = 100 -ohm

The average power dissipated by the resistor is given by;

[tex]P_{avg} = \frac{1}{2} I_oV_o= I_{rms}V_{rms} = \frac{V_{rms}^2}{R}[/tex]

where;

[tex]V_{rms}[/tex] is the root-mean-square-voltage

[tex]V_{rms} = \frac{V_o}{\sqrt{2}} \\\\V_{rms} = \frac{120}{\sqrt{2}}\\\\V_{rms} = 84.853 \ V[/tex]

The average power dissipated by the resistor is calculated as;

[tex]P_{avg} = \frac{V_{rms}^2}{R}\\\\P_{avg} = \frac{84.853^2}{100}\\\\P_{avg} = 72 \ W[/tex]

Therefore, the average power dissipated is 72 W.

The correct answer is C. The inner planets are also called terrestrial planets.

Explanation:

Our solar system includes a total of eight planets. Additionally, planets are classified into broad categories including inner planets and outer planets. The inner planets category applies to planets such as Earth, Mercury, or Mars because these are located within the asteroid belt (region of asteroids between Mars and Jupiter). Moreover, inner planets differ from others due to their composition as they are composed of rocks and metals. Also, due to this composition, these are known as terrestrial planets. According to this, the statement that best describes inner planets is "The inner planets are also called terrestrial planets".

Answer:

The answer is c.) The inner planets are also called terrestrial planets.

Explanation:

Answer:

ΔT = 1ºC , 2ºCand 3ºC

Explanation:

In this exercise they indicate the specific heat of lithium

let's calculate the temperature increase as a function of the heat introduced

          Q = m [tex]c_{e}[/tex] ΔT

          ΔT = Q / m c_{e}

calculate

 for Q = 3.5 J

         ΔT = 3.5 / (1 3.5)

         ΔT = 1ºC

For Q = 7.0 J

         ΔT = 7 / (1 3.5)

         ΔT = 2ºC

for Q = 10.5 J

         ΔD = 10.5 / (1 3.5)

         ΔT = 3ºC

we see that this is a straight line, see attached

Explanation:

Given that,

Initial speed of the rock, u = 30 m/s

The acceleration due to gravity at the surface of the moon is 1.62 m/s².

We need to find the time when the rock is ascending at a height of 180 m.

The rock is projected from the surface of the moon. The equation of motion in this case is given by :

[tex]h=ut-\dfrac{1}{2}gt^2\\\\180=30t-\dfrac{1}{2}\times 1.62t^2[/tex]

It is a quadratic equation, after solving whose solution is given by:

t = 7.53 s

or

t = 8 seconds

(e)If it is decending, v = -20 m/s

Now t' is the time of descending. So,

[tex]v=-u+gt\\\\t=\dfrac{v+u}{g}\\\\t=\dfrac{20+30}{1.62}\\\\t=30.86\ s[/tex]

Let h' is the height of the rock at this time. So,

[tex]h'=ut-\dfrac{1}{2}gt^2\\\\h'=30\times 30.86-\dfrac{1}{2}\times 1.62\times 30.86^2\\\\h'=154.40\ m[/tex]

or

h' = 155 m

Answer:

The AC generator has one unbroken slip ring

Explanation:

In physics, the application of electromagnetic induction can be seen in generators and dynamos. Electromagnetic induction is the process of generating electricity using magnets. It found applications in generators and the types of generator they found application is in AC and DC generator.

An AC generator is also called a Dynamo. A DC generator contains what is called a SPLIT RING fixed to the end of the coil which can be separated and coupled back according to the name "split". An AC generator also called a Dynamo makes use of a SLIP ring which cannot be divided into two. It comes as an entity. The presence of this rings is what differentiates a DC generator from an AC generator.

We can replace split rings with slip rings when converting a DC generator to an AC generator and vice versa.

It can therefore be concluded that the difference between a DC and an AC generator is that the AC generator has one unbroken slip ring.

B. A chemical change

Explanation:

I'm guessing ?

Answer:

changing the magnetic field more rapidly

Explanation:

According to Faraday's law, whenever there is a change in the magnetic lines of force, it leads the production of induced emf. The magnitude of induced emf is proportional to to the rate of change of flux.

Hence if the magnetic field inside a loop of wire is changed rapidly, the magnitude of induced emf increases in accordance with Faraday's law of electromagnetic induction stated above when the magnetic field is changed more rapidly, hence the answer.

Answer:

B. mineral oil – density of 0.910 g/mL.

Explanation:

Hello,

In this case, since the density is known as the degree of compactness a body has (mass in the occupied volume), the higher the density, the higher the weight of the body, therefore, if submerged into a liquid it could float if less dense than the liquid or sink if more dense than the liquid.

In such a way, since the rubber is more dense than mineral (0.960 g/mL > 0.910 g/mL) oil but less dense than distilled water (0.960 g/mL < 1.0 g/mL) we can say that B. mineral oil – density of 0.910 g/mL is directly above it when submerged.

Best regards.

The researchers need to compare those who contracted the disease to those who did not.

Answer:

The torque is 11.27 N m

Explanation:

Recall that torque is the vector product of the force times the distance to the pivoting point. So in our case, the distance to the pivoting point is the radius of the cylinder (0.05 m), and the force is given by the weight of the bucket full of water (W = 9.8 * 23 N = 225.4 N)

Then the torque is: 0.05 * 225.4 N m = 11.27 N m

Answer:

The resultant vector is [tex]\vec R = \vec A + \vec B = 7.196\,i + 6.464\,j[/tex].

Explanation:

First, each vector is determined in terms of absolute coordinates:

6-meter vector with direction: 30º north of east.

[tex]\vec A = (6\,m)\cdot (\cos30^{\circ} \,i + \sin 30^{\circ}\,j)[/tex]

[tex]\vec A = 5.196\,i + 3\,j[/tex]

4-meter vector with direction: 30º east of north.

[tex]\vec B = (4\,m)\cdot (\cos 60^{\circ}\,i + \sin 60^{\circ}\,j)[/tex]

[tex]\vec B = 2\,i + 3.464\,j[/tex]

The resultant vector is obtaining by sum of components:

[tex]\vec R = \vec A + \vec B = 7.196\,i + 6.464\,j[/tex]

The resultant vector is [tex]\vec R = \vec A + \vec B = 7.196\,i + 6.464\,j[/tex].

Answer:

1.34 mm

Explanation:

A double slit experiment is conducted with a light which has a wavelength of 620 nm

The fringes are separated 2.3 mm apart

The light is changed to a wavelength length of 360 nm

Let x represent the fringe spacing as a result of the change in wavelength

Therefore,the fringe spacing can be calculated as follows

2.3mm/x= 620nm/360nm

Multiply both sides

x × 620= 2.3×360

620x= 828

x= 828/620

x= 1.34 mm

Answer:

The magnification is  [tex]m = 12[/tex]

Explanation:

From the question  we are told that

   The object distance is [tex]u = 36.2 \ cm[/tex]

     The focal length is  [tex]v = 39.5 \ cm[/tex]

From the lens equation we have that

         [tex]\frac{1}{f} = \frac{1}{u} + \frac{1}{v}[/tex]

=>     [tex]\frac{1}{v} = \frac{1}{f} - \frac{1}{u}[/tex]

substituting values

       [tex]\frac{1}{v} = \frac{1}{39.5} - \frac{1}{36.2}[/tex]

       [tex]\frac{1}{v} = -0.0023[/tex]

=>   [tex]v = \frac{1}{0.0023}[/tex]

=>   [tex]v =-433.3 \ cm[/tex]

The magnification is mathematically represented as

         [tex]m =- \frac{v}{u}[/tex]

substituting values

        [tex]m =- \frac{-433.3}{36.2}[/tex]

         [tex]m = 12[/tex]

Answer:

θ = 45.15°

Explanation:

We need to use the grating equation in this question. The grating equation is given as follows:

mλ = d Sin θ

where,

m = order number = 3

λ = wavelength of light = 520 nm = 5.2 x 10⁻⁷ m

d = slit spacing = 2.2 μm = 2.2 x 10⁻⁶ m

θ = angle from the axis = ?

Therefore,

(3)(5.2 x 10⁻⁷ m) = (2.2 x 10⁻⁶ m) Sin θ

Sin θ = (3)(5.2 x 10⁻⁷ m)/(2.2 x 10⁻⁶ m)

Sin θ = 0.709

θ = Sin⁻¹(0.709)

θ = 45.15°

Image is missing, so i have attached it

Answer:

19.04 × 10⁻⁴ T in the +x direction

Explanation:

We are told that the point P which is equidistant from the wires. (R = 5.00 cm). Thus distance from each wire to O is R.

Hence, the magnetic field at P from each wire would be; B = μ₀I/(2πR)

We are given;

I = 2.4 A

R = 5 cm = 0.05 m

μ₀ is a constant = 4π × 10⁻⁷ H/m

B = (4π × 10⁻⁷ × 2.4)/(2π × 0.05)

B = 9.6 × 10⁻⁴ T

To get the direction of the field from each wire, we will use Flemings right hand rule.

From the diagram attached:

We can say the field at P from the top wire will point up/right

Also, the field at P from the bottom wire will point down/right

Thus, by symmetry, the y components will cancel out leaving the two equal x components to act to the right.

If the mid-point between the wires is M, the the angle this mid point line to P makes with either A or B should be same since P is equidistant from both wires.

Let the angle be θ

Thus;

sin(θ) = (1.3/2)/5

θ = sin⁻¹(0.13) = 7.47⁰

The x component of each field would be:

9.6 × 10⁻⁴cos(7.47) = 9.52 × 10⁻⁴ T

Thus, total field = 2 × 9.52 × 10⁻⁴ = 19.04 × 10⁻⁴ T in the +x direction

The magnitude of the magnetic field at the point P will be "9.6 × 10⁻⁴ T".

The region of the environment close to something like a magnetic entity or a current-carrying body wherein this same magnetic forces caused by the body as well as a current might well be sensed.

According to the question,

Current, I = 2.4 A

Radius, R = 5 cm or,

                = 0.05 m

Constant, μ₀ = 4π × 10⁻⁷ H/m

We know the relation,

The magnetic field, B = [tex]\frac{\mu_0 I}{2 \pi R}[/tex]

By substituting the values in the above relation, we get

                                    = [tex]\frac{4 \pi\times 10^{-7}\times 2.4}{2 \pi\times 0.05}[/tex]

                                    = 9.6 × 10⁻⁴ T

Thus the above answer is appropriate.

Find out more information about magnetic field here:

https://brainly.com/question/14411049

Answer:

1. Berenice  = 0.67 D

2. Avishka  = 1.50 D

3. Francesca  = 2.00 D

4. Edouard = 2.75 D

Explanation:

The farsighted people are those with near point greater than 25 cm.

They include Avishka, Berenice, Edouard and Francisca.

A converging lens is needed to correct farsightedness, or hyperopia, therefore, the focal length, f, is positive. The image formed is virtual and on the same side of the lens. Thus the image distance is negative

From the lens formula, 1/f = 1/v  1/u; but v is negative

Therefore, 1/f = 1/u - 1/v

But, power of a lens = 1/f in meters.

Therefore,  P =  1/u - 1/v

For Avishka, u = 25 cm or 0.25 m, v = 0.4 m

P = 1/ 0.25 - 1/0.4 = 1.5 D

For Berenice, u = 0.25 m, v = 0.3 m

P = 1/0.25 - 1/0.30 =0.7 D

For Edouard, u = 0.25 m, v = 0.80 m

P = 1/0.25 - 1/0.80 =2.75 D

For Francesca, u = 0.25 m, v = 0.50 m

P = 1/0.25 - 1/0.5 = 2.0 D

When The farsighted people are those with a near point greater than 25cm.

Berenice is = 0.67 D

Avishka is = 1.50 D

Francesca is = 2.00 D

Edouard is = 2.75 D

When The farsighted people are those with a near point greater than 25 cm. Then, They include Avishka, Berenice, Edouard, and also Francisca.

Also, A converging lens is needed to correct farsightedness, or hyperopia, thus, When the focal length, f, is positive. Also, The image formed is virtual and also on the same side of the lens. hence the image distance is negative.

Also, From the lens formula, 1/f = 1/v 1/u; but v is negative

Thus, 1/f = 1/u - 1/v

But, when the power of a lens = 1/f in meters.

Thus, P = 1/u - 1/v

For Avishka, u = 25 cm or 0.25 m, v = 0.4 m

After that, P = 1/ 0.25 - 1/0.4 = 1.5 D

Then, For Berenice, u = 0.25 m, v = 0.3 m

Now, P = 1/0.25 - 1/0.30 =0.7 D

For Edouard, u = 0.25 m, v is = 0.80 m

Then, P = 1/0.25 - 1/0.80 is =2.75 D

Now, For Francesca, u = 0.25 m, v is = 0.50 m

Therefore, P = 1/0.25 - 1/0.5 = 2.0 D

Find more information about Hyperopic Vision here:

https://brainly.com/question/25676535

Answer:

Pls seeattached file

Explanation:

A resistor made of Ni chrome wire is used in an application where its resistance cannot be more than 1.35 % so its temperature range will be from 33.75 to -33.75 °C.

Electrical resistance, or resistance to electricity, is a force that opposes the flow of current. Ohms are used to expressing resistance values.

When there is an electron difference between two terminals, electricity will flow from high to low. In opposition to that flow is resistance. As resistance rises, the current declines. On the other side, when the resistance falls, the current rises.

According to the question,

R = R₀ (1 + α ΔT)

(1 + 0.0135)R₀ = R₀(1 + α ΔT)

ΔT = (1 + 0.0135) / α

= 0.0135 / 0.0004

= 33.75 °C.

ΔT = [(1 - 0.0135) -1]/0.004

= -33.75 °C

To get more information about Resistance :

https://brainly.com/question/11431009

#SPJ5

Answer:

b

Explanation:

The correct answer is D. An average city

Explanation:

A neutron star differs from others due to its massive density, this means a lot of matter is compressed in a small area. Indeed, neutron stars have a mass of around 1.4 to 2.8 times the mass of the sun. But these are considerably small as they only measure around 20 kilometers, which is the size of an average city. Additionally, neutron stars are this dense because they are the result of a regular star exploding, which leads to a super-dense core, or neutron star. In this context, the mass of a neutron star is compressed to the size of an average city.

Answer:

2f

Explanation:

The formula for the object - image relationship of thin lens is given as;

1/s + 1/s' = 1/f

Where;

s is object distance from lens

s' is the image distance from the lens

f is the focal length of the lens

Total distance of the object and image from the lens is given as;

d = s + s'

We earlier said that; 1/s + 1/s' = 1/f

Making s' the subject, we have;

s' = sf/(s - f)

Since d = s + s'

Thus;

d = s + (sf/(s - f))

Expanding this, we have;

d = s²/(s - f)

The derivative of this with respect to d gives;

d(d(s))/ds = (2s/(s - f)) - s²/(s - f)²

Equating to zero, we have;

(2s/(s - f)) - s²/(s - f)² = 0

(2s/(s - f)) = s²/(s - f)²

Thus;

2s = s²/(s - f)

s² = 2s(s - f)

s² = 2s² - 2sf

2s² - s² = 2sf

s² = 2sf

s = 2f

Answer:

The magnitude of the magnetic flux through the loop is 0.0982 T.m²

Explanation:

Given;

magnitude of magnetic field, B = 0.5 T

radius of the loop, r = 0.25 m

Area of the loop is given by;

A = πr²

A = 3.142 x (0.25)²

A = 0.1964 m²

The magnitude of the magnetic flux through the loop is given by;

Ф = BA

Where;

B is the magnitude of the magnetic field

A is area of the field

Ф = 0.5 x 0.1964

Ф = 0.0982 T.m²

Therefore, the magnitude of the magnetic flux through the loop is 0.0982 T.m²

Answer:

The speed of the proton is 4059.39 m/s

Explanation:

The centripetal force on the particle is given by;

[tex]F = \frac{mv^2}{r}[/tex]

The magnetic force on the particle is given by;

[tex]F = qvB[/tex]

The centripetal force on the particle must equal the magnetic force on the particle, for the particle to remain in the circular path.

[tex]\frac{mv^2}{r} = qvB\\\\r = \frac{mv^2}{qvB} \\\\r = \frac{mv}{qB}[/tex]

where;

r is the radius of the circular path moved by both electron and proton;

⇒For electron;

[tex]r = \frac{(9.1*10^{-31})(7.45*10^6)}{(1.602*10^{-19})(1.1*10^{-5})}\\\\r = 3.847 \ m[/tex]

⇒For proton

The speed of the proton is given by;

[tex]r = \frac{mv}{qB}\\\\mv = qBr\\\\v = \frac{qBr}{m} \\\\v = \frac{(1.602*10^{-19})(1.1*10^{-5})(3.847)}{1.67*10^{-27}} \\\\v = 4059.39 \ m/s[/tex]

Therefore, the speed of the proton is 4059.39 m/s

Answer:

This is because the same electron removed from the positively charged plate is what is taken to the negatively charged plate, maintaining the same amount of electron according to the conservation of charge in an electric circuit.

Explanation:

In any circuit, electrons are neither created nor destroyed according to the laws of conservation of charge, but are transferred from one point to another on the circuit. When the plates of a capacitor are connected to battery, the battery pushes the electron to move due to its potential difference. Electrons are then moved from the positive plate, at a steady rate, to the negative plate. The removal of electrons from the positive plate is what leaves it positively charged from deficiency of electrons, and the addition of electrons at the negatively charged plate is what leaves the plate negatively charge from excess of electrons. From this, we can see that the same electrons removed from the positively charged plate are  taken to the negatively charged plate.

Answer:

Explanation:

B. There is a counterclockwise induced current in the loop

Explanation:

This in line with the right hand grip rule,

The right hand rule states that: to determine the direction of the magnetic force on a positive moving charge, ƒ, point the thumb of the right hand in the direction of v, the fingers in the direction of B, and a perpendicular to the palm points in the direction of F.

Answer:

displacements are 0.776m, 0.114m

Explanation:

We were given mass of 26-g rifle bullet , then we can convert to Kg since

Momentum is conserved here.

The initial momentum before impact = (Mi * Vi)

Where Mi= initial given mass

Vi=initial velocity given

= 0.026 * 220 = 5.72 kgm/s

The final momentum after impact is (Mf * Vf )

Mf= final mass

5.72=( 3.82* Vf )

= 5.72/ 3.82

= 1.497 m/s

the speed of the pendulum bob with bullet afterwards= 1.497 m/s

the total energy after the collision is the addition of the kinetic energy of the bob+bullet and the potential energy of the bob and bullet, potential energy can be taken as zero.

M = 3.82 kg the mass of the bob containing the bullet

E(total) = ¹/₂MV² = 1/2 * (3.82kg)*(1.497m/s)² = 4.280J

When the Bob got to highest point the kinetic energy is zero and the potential energy is due to the increase in height of the bob, and the addition of the potential and kinetic energies still equal the total energy from before

E(total) = Mgh + 0 = Mgh = 4.280J

solving for h and substituting,

h = 4.280 J/(9.8m/s^2*3.82kg) = 0.114 m

Since the height is found,we the angle of the pendulum at the top of the swing can also be determined

A = arccos[(2.7 - 0.114) / 2.7] or A = 16.71degrees

Since A is known, the displacement along the horizontal axis can be calculated as

x = 2.7* sin(A) = 0.776m

therefore, displacement is 0.776m, 0.114m

the vertical and horizontal component of the pendulum's maximum displacement are displacement is 0.776m, 0.114m