Answer:
B
8.5 km/h east
Explanation:
Relative velocity= Va -Vb
=10-1.5
=8.5 km/h east
The concept relative speed is used when two or more bodies moving with some speed are considered. The relative speed of woman to the boat is 8.5 km/h east. The correct option is B.
What is relative speed?The relative speed of two bodies is defined as the sum of their speeds if they are moving in the opposite direction and it is the difference of their speeds if they are moving in the same direction.
The speed of the moving body with respect to the stationary body is known as the relative speed. The term relative means in comparison to. The relative speed is a scalar quantity.
Here both the boat and women are travelling in the same direction. So the relative speed is given as:
Relative speed = 10 - 1.5 = 8.5 km / h
Therefore the relative speed is 8.5 km/h east.
Thus the correct option is B.
To know more about relative speed, visit;
https://brainly.com/question/11476119
#SPJ7
A weightlifter works out at the gym each day. Part of her routine is to lie on her back and lift a 43 kg barbell straight up from chest height to full arm extension, a distance of 0.53 m .
Part A: How much work does the weightlifter do to lift the barbell one time?
Part B: If the weightlifter does 23 repetitions a day, what total energy does she expend on lifting, assuming a typical efficiency for energy use by the body?
Part C: How many 500 Calorie donuts can she eat a day to supply that energy?
Answer:
A) Workdone = 223.57 N-m
B) 22357 J of energy
C) Number of donuts = 10.7 donuts
Explanation:
A) The work done is calculated from the formula;. Work done = Force × Distance
We are given;
Mass; m = 43 kg
Distance = 0.53 m
Force(weight) = mg = 43 × 9.81
Thus;
Work done = 43 × 9.81 × 0.53
Workdone = 223.57 N-m
B) We are told she does 23 repetitions a day.
Thus, we assume 23% efficiency.
So, Work = Energy
Thus;
At 100% efficiency;
Energy = (223.57/100%) × 23 repetitions = 5142.11 J
Now, since she is only 23% efficient, she will expend; 5142.11/0.23 J = 22357 J of energy to do 5390 J of work.
C) from conversions; 4.18 J = 1 calorie
Thus;
22357 J ÷ 4.18 J/cal = 5348.565 calories
We how many 500 calorie donuts she can eat in a day to supply that energy.
Thus;
Number of donuts = 5348.565 cal ÷ 500 cal /donut
Number of donuts = 10.7 donuts
A hammer is used to hit a nail into a board. Which statement is correct about the forces at play between the nail and the hammer?
O The nail exerts a much smaller force on the hammer in the opposite direction
O The nail exerts a much smaller force on the hammer in the same direction.
The nail exerts an equal force on the hammer in the same direction.
O The nail exerts an equal force on the hammer in the opposite direction.
Answer:
reviewing the final statements, the correct one is the quarter
The nail exerts an equal force on the hammer in the opposite direction.
Explanation:
This is an action-reaction problem or Newton's third law, which states that forces in naturals occur in pairs.
This is the foregoing, the hammer exerts a force on the nail of magnitude F and it will direct downwards, if we call this action and the nail exerts a force on the hammer of equal magnitude but opposite direction bone directed upwards, each force is applied in one of the bodies.
The difference in result that each force is that the force between the nail exerts a very high pressure (relation between the force between the nail area), instead the area of the hammer is much greater, therefore the pressure is small.
When reviewing the final statements, the correct one is the quarter
The nail exerts an equal force on the hammer in the opposite direction.
A velocity selector can be used to measure the speed of a charged particle. A beam of particles is directed along the axis of the instrument. A parallel plate capacitor sets up an electric field E which is oriented perpendicular to a uniform magnetic field B. If the plates are separated by 3 mm and the value of the magnetic field is 0.3 T, what voltage between the plates will allow particles of speed 5 x 105 m/s to pass straight through without deflection? A. 70 V B. 140 V C. 450 V D. 1,400 V E. 2,800 V
Answer:
C. 450v
Explanation:
Using
Voltage= B*distance of separation*velocity
3mm x 0.3T x 5E5m/s
= 450v
Which one of the following lists gives the correct order of the electromagnetic spectrum from low to high frequencies?
A) radio waves, infrared, microwaves, ultraviolet, visible, x-rays, gamma rays
B) radio waves, ultraviolet, x-rays, microwaves, infrared, visible, gamma rays
C) radio waves, microwaves, infrared, visible, ultraviolet, x-rays, gamma rays
D) radio waves, microwaves, visible, x-rays, infrared, ultraviolet, gamma rays
E) radio waves, infrared, x-rays, microwaves, ultraviolet, visible, gamma rays
Answer:
C) radio waves, microwaves, infrared, visible, ultraviolet, x-rays, gamma rays
Explanation:
radio waves have lowest energy , lowest frequency and highest wavelength
gamma rays have highest energy , highest frequency and least wavelength
Answer: C
Explanation:
You have a lightweight spring whose unstretched length is 4.0 cm. First, you attach one end of the spring to the ceiling and hang a 1.8 g mass from it. This stretches the spring to a length of 5.1 cm . You then attach two small plastic beads to the opposite ends of the spring, lay the spring on a frictionless table, and give each plastic bead the same charge. This stretches the spring to a length of 4.3 cm .
Requried:
What is the magnitude of the charge (in nC) on each bead?
Answer:
2.2nC
Explanation:
Call the amount by which the spring’s unstretched length L,
the amount it stretches while hanging x1
and the amount it stretches while on the table x2.
Combining Hooke’s law with Newton’s second law, given that the stretched spring is not accelerating,
we have mg−kx1 =0, or k = mg /x1 , where k is the spring constant. On the other hand,
applying Coulomb’s law to the second part tells us ke q2/ (L+x2)2 − kx2 = 0 or q2 = kx2(L+x2)2/ke,
where ke is the Coulomb constant. Combining these,
we get q = √(mgx2(L+x2)²/x1ke =2.2nC
Radar is used to determine distances to various objects by measuring the round-trip time for an echo from the object. (a) How far away (in m) is the planet Venus if the echo time is 900 s? m (b) What is the echo time (in µs) for a car 80.0 m from a Highway Patrol radar unit? µs (c) How accurately (in nanoseconds) must you be able to measure the echo time to an airplane 12.0 km away to determine its distance within 11.5 m? ns
Answer:
a) 1.35 x 10^11 m
b) 0.53 µs
c) 8 ns
Explanation:
Radar involves the use of radio wave which has speed c = 3 x 10^8 m/s
a) for 900 s,
The distance for a round trip = v x t
==> (3 x 10^8) x 900 = 2.7 x 10^11 m
The distance of Venus is half this round trip distance = (2.7 x 10^11)/2 = 1.35 x 10^11 m
b) for a 80.0 m distance of the car from the radar source, the radar will travel a total distance of
d = 2 x 80 = 160 m
the time taken = d/c = 160/(3 x 10^8) = 5.3 x 10^-7 s = 0.53 µs
c) accuracy in distance Δd = 11.5 m
Δt = accuracy in time = Δd/c = 11.5/(3 x 10^8) = 3.8 x 10^-8 = 38 ns
Light of wavelength 550 nm is incident on a slit having a width of 0.200 mm. The viewing screen is 1.90 m from the slit. Find the width of the central bright fringe
Answer:
The width of Center bright fringe is 10.2mm
Explanation:
Given that if
Y/ L << 1 then
Sin theta will be approx Y/L
So sin theta approx Y/L = lamda/a
Y= a x lambda/a
By substituting
1.9x 10^ -3m x 550*10^-9/ 0.2 x 10^-3m
= 5.2mm
But
Change in y = 2y = 10.4mm
A hot cup of coffee is placed on a table. Which will happen because of conduction? Answer options with 4 options A. The temperature of the coffee will decrease while the temperature of the table decreases. B. The temperature of the coffee will increase while the temperature of the table increases. C. The temperature of the coffee will decrease while the temperature of the table increases. D. The temperature of the coffee will increase while the temperature of the table decreases.
Answer:
C.Explanation:
C. The temperature of the coffee will decrease while the temperature of the table increases.
Find the minimum thickness (in nm) of a soap bubble that appears green when illuminated by white light perpendicular to its surface. Take the wavelength to be 549 nm, and assume the same index of refraction as water (nw
Answer:
103nm
Explanation:
Pls see attached file
A woman was told in 2020 that she had exactly 15 years to live. If she travels away from the Earth at 0.8 c and then returns at the same speed, the last New Year's Day the doctors expect her to celebrate is:
Answer:
2035
Explanation:
The doctor does not travel with the woman, and therefore, he won't experience any relativistic effect on his time. The doctor will judge time by the time here on earth. Technically, the last new year's day the doctor, who is here on earth, would expect the woman to celebrate will be in 2020 + 15 years = 2035
To celebrate a victory, a pitcher throws her glove straight upward with an initial speed of 5.0 m/s. How much time does it take for the glove to return to the pitcher
Answer:
The glove takes 1.02s to return to the pitchers hand.
Explanation:
Given;
initial velocity the pitcher's glove, u = 5 m/s
Apply kinematic equation
s = ut - ¹/₂gt²
where;
g is acceleration due to gravity = 9.8 m/s²
t is the time takes the glove to return to the pitchers hand
s is the displacement of the glove, which will be equal to zero when the glove returns to the pitchers hand. (s = 0)
0 = ut - ¹/₂gt²
ut = ¹/₂gt²
u = ¹/₂gt
gt = 2u
t = (2u) / g
t = (2 x 5) / 9.8
t = 1.02 s
Therefore, the glove takes 1.02s to return to the pitchers hand.
An L-R-C series circuit has L = 0.450 H, C=2.50×10^−5F, and resistance R.
Required:
a. What is the angular frequency of the circuit when R = 0?
b. What value must R have to give a decrease in angular frequency of 10.0 % compared to the value calculated in Part a.
Answer:
298rad/s and 116.96 ohms
Explanation:
Given an L-R-C series circuit where
L = 0.450 H,
C=2.50×10^−5F, and resistance R= 0
In this situation we have a simple LC circuit with angular frequency
Wo = 1√LC
= 1/√(0.450)(2.50×10^-5)
= 1/√0.00001125
= 1/0.003354
= 298rad/s
B) Now we need to find the value of R such that it gives a 10% decrease in angular frequency.
Wi/W° = (100-10)/100
Wi/W° = 90/100
Wi/W° = 0.90 ............... 1
Angular frequency of oscillation
The complete aspect of the solution is attached, please check.
a. The angular frequency of the circuit when R = 0 Ohms is 294.12 rad/s.
b. The value R must have to give a decrease in angular frequency of 10.0 % compared to the initial value is equal to 116.96 Ohms.
Given the following data:
Inductance, L = 0.450 HenryCapacitance, C = [tex]2.50\times 10^{-5}[/tex] Faradsa. To determine the angular frequency of the circuit when R = 0 Ohms:
Mathematically, the angular frequency of a LC circuit is given by the formula:
[tex]\omega = \frac{1}{\sqrt{LC} } \\\\\omega =\frac{1}{\sqrt{0.450 \times 2.50\times 10^{-5}}} \\\\\omega =\frac{1}{\sqrt{1.125 \times 10^{-5}}} \\\\\omega = \frac{1}{0.0034} \\\\\omega = 294.12\;rad/s[/tex]
b. To find the value R must have to give a decrease in angular frequency of 10.0 % compared to the value calculated above:
The mathematical expression is given as follows:
[tex]\frac{\omega_f}{\omega_i} = \frac{100-10}{100} \\\\\frac{\omega_f}{\omega_i} =\frac{90}{100} \\\\\frac{\omega_f}{\omega_i} =0.9[/tex]
[tex](\frac{\omega_f}{\omega_i})^2 = 1 - \frac{R^2C}{4L} \\\\0.90^2=1 - \frac{R^2C}{4L}\\\\R=\sqrt{\frac{4L(1-0.81)}{C}} \\\\R=\sqrt{\frac{4\times 0.450 \times (0.19)}{2.50\times 10^{-5}}}\\\\R = \sqrt{\frac{0.342}{2.50\times 10^{-5}} }\\\\R =\sqrt{13680}[/tex]
R = 116.96 Ohms.
Read more: https://brainly.com/question/23754122
An optical disk drive in your computer can spin a disk up to 10,000 rpm (about 1045 rad/s ). If a particular disk is spun at 998.0 rad/s while it is being read, and then is allowed to come to rest over 0.502 seconds , what is the magnitude of the average angular acceleration of the disk?
Answer:
1988.05 rad/s^2
Explanation:
The angular speed of the optical disk ω = 998.0 rad/s
the time taken to come to rest t = 0.502 s
The magnitude of the average angular acceleration ∝ = ω/t
∝ = 998.0/0.502 = 1988.05 rad/s^2
How much time will elapse if a radioisotope with a half-life of 88 seconds decays to one-sixteenth of its original mass?
Answer:
352 seconds are needed for the radioisotope to decay to one-sixteenth of its original mass.
Explanation:
The decay of radioisotopes are represented by the following ordinary differential equation:
[tex]\frac{dm}{dt} = -\frac{t}{\tau}[/tex]
Where:
[tex]t[/tex] - Time, measured in seconds.
[tex]\tau[/tex] - Time constant, measured in seconds.
[tex]m[/tex] - Mass of the radioisotope, measured in grams.
The solution of this expression is:
[tex]m(t) = m_{o}\cdot e^{-\frac{t}{\tau} }[/tex]
Where [tex]m_{o}[/tex] is the initial mass of the radioisotope, measured in kilograms.
The ratio of current mass to initial mass is:
[tex]\frac{m(t)}{m_{o}} = e^{-\frac{t}{\tau} }[/tex]
The time constant is now calculated in terms of half-life:
[tex]\tau = \frac{t_{1/2}}{\ln2}[/tex]
Where [tex]t_{1/2}[/tex] is the half-life of the radioisotope, measured in seconds.
Given that [tex]t_{1/2} = 88\,s[/tex], the time constant of the radioisotope is:
[tex]\tau = \frac{88\,s}{\ln 2}[/tex]
[tex]\tau \approx 126.957\,s[/tex]
Now, if [tex]\frac{m(t)}{m_{o}(t)} = \frac{1}{16}[/tex] and [tex]\tau \approx 126.957\,s[/tex], the time is:
[tex]t = -\tau \cdot \ln\frac{m(t)}{m_{o}}[/tex]
[tex]t = -(126.957\,s)\cdot \ln \frac{1}{16}[/tex]
[tex]t \approx 352\,s[/tex]
352 seconds are needed for the radioisotope to decay to one-sixteenth of its original mass.
Select the situation for which the torque is the smallest.
a. A 200 kg piece of silver is placed at the end of a 2.5 m tree branch.
b. A 20 kg piece of marble is placed at the end of a 25 m construction crane arm.
c. A 8 kg quartz rock is placed at the end of a 62.5 m thin titanium rod.
d. The torque is the same for two cases.
e. The torque is the same for all cases.
Answer:
e. The torque is the same for all cases.
Explanation:
The formula for torque is:
τ = Fr
where,
τ = Torque
F = Force = Weight (in this case) = mg
r = perpendicular distance between force an axis of rotation
Therefore,
τ = mgr
a)
Here,
m = 200 kg
r = 2.5 m
Therefore,
τ = (200 kg)(9.8 m/s²)(2.5 m)
τ = 4900 N.m
b)
Here,
m = 20 kg
r = 25 m
Therefore,
τ = (20 kg)(9.8 m/s²)(25 m)
τ = 4900 N.m
c)
Here,
m = 8 kg
r = 62.5 m
Therefore,
τ = (8 kg)(9.8 m/s²)(62.5 m)
τ = 4900 N.m
Hence, the correct answer will be:
e. The torque is the same for all cases.
Which of the following frequencies could NOT be present as a standing wave in a 2m long organ pipe open at both ends? The fundamental frequency is 85 Hz.
Answer:
382Hz
Explanation:
The question lacks the required option. Find the complete question in the attachment.
The long organ pipe open at both ends is called an open pipe. The fundamental frequency for an open pipe is expressed as F0 = V/2L
Harmonics are integral multiples of the fundamental frequency. For open pipes its harmonics are 2fo, 3fo, 4fo, 5fo...
Given fundamental frequency f0 to be 85 Hz, the following frequencies will be present as a standing wave;
First overtone f1 = 2fo = 2(85) = 170Hz
Second overtone f2 = 3fo = 3(85) = 255Hz
Third overtone = 4fo = 4(85) = 340Hz
Based on the option it can be seen that the only frequency that is not present as a standing wave is 382Hz
A stationary coil is in a magnetic field that is changing with time. Does the emf induced in the coil depend
Answer:
Explanation:
The e.m.f induced in the coil depend on the following :
(a) No. of turns in the coil
(b) Cross-sectional Area of the coil
(c) Magnitude of Magnetic field
(d) Angular velocity of the coil
6. You push an object, initially at rest, across a frictionless floor with a constant force for a time interval t, resulting in a final speed of v for the object. You then repeat the experiment, but with a force that is twice as large. What time interval is now required to reach the same final speed v?
Answer:
t = t₀ / 2
Explanation:
In this exercise we must use Newton's second law
F = m a
a = F / m
now we can use kinematics
as in object part of rest (v₀ = 0)
v =a t₀
t₀ = v / a
these results are with the first experiment
now repeat the experiment, but F = 2F₀
a = 2F₀ / m = 2 a₀
v = 2 a₀ t
t = v / 2a₀
t = t₀ / 2
The time interval that is required to reach the same final speed (V) is equal to [tex]t=\frac{\Delta t}{2}[/tex].
Given the following data:
Initial speed = 0 m/s (since the object is at rest)Final speed = VTime = [tex]\Delta t[/tex]Speed = VTo find the time interval that is now required to reach the same final speed (V), we would apply Newton's Second Law of Motion:
Mathematically, Newton's Second Law of Motion is given by this formula;
[tex]F = \frac{M(V-U)}{t}[/tex]
Where:
F is the force.V is the final velocity.U is the initial velocity.t is the time.Substituting the given parameters into the formula, we have;
[tex]F = \frac{M(V-0)}{\Delta t}\\\\F = \frac{MV}{\Delta t}[/tex]
When the experiment is repeated, the magnitude of the force is doubled:
[tex]F = 2F[/tex]
Now, we can find the time interval that is required to reach the same final speed (V):
[tex]F = \frac{M(V-0)}{t}\\\\t=\frac{MV}{F}[/tex]
Substituting the value of F, we have:
[tex]t=\frac{MV}{2F} \\\\t=\frac{MV}{\frac{2MV}{\Delta t}} \\\\t=MV \times \frac{\Delta t}{2MV} \\\\t=\frac{\Delta t}{2}[/tex]
Read more here: https://brainly.com/question/24029674
If a convex lens were made out of very thin clear plastic filled with air, and were then placed underwater where n = 1.33 and where the lens would have an effective index of refraction n = 1, the lens would act in the same way
a. as a flat refracting surface between water and air as seen from the water side.
b. as a concave mirror in air.
c. as a concave lens in air.
d. as the glasses worn by a farsighted person.
e. as a convex lens in air.
Answer:
D. A convex lens in air
Explanation:
This is because the air tight plastic under water will reflect light rays in the same manner as a convex lens
Tech A says parallel circuits are like links in a chain. Tech B says total current in a parallel circuit equals the sum of the current flowing in each branch of the circuit. Who is correct?
Answer: Only Tech B is correct.
Explanation:
First, tech A is wrong.
The circuits that can be compared with links in a chain are the series circuit, and it can be related to the links in a chain because if one of the elements breaks, the current can not flow furthermore (because the elements in the circuit are connected in series) while in a parallel circuit if one of the branches breaks, the current still can flow by other branches.
Also in a parallel circuit, the sum of the currents of each path is equal to the current that comes from the source, so Tech B is correct, the total current is equal to the sum of the currents flowing in each branch of the circuit.
A stone is dropped from the upper observation deck of a tower, 50 m above the ground. (Assume g = 9.8 m/s2.) (a) Find the distance (in meters) of the stone above ground level at time t. h(t) = (b) How long does it take the stone to reach the ground? (Round your answer to two decimal places.) s (c) With what velocity does it strike the ground? (Round your answer to one decimal place.) m/s (d) If the stone is thrown downward with a speed of 9 m/s, how long does it take to reach the ground? (Round your answer to two decimal places.)
Answer:
A. Using displacement =Ut + 1/2gt²
=> 0 + 1/2 (-9.8)t²
= -4.9t²
So
h(t) = 50+ displacement
= 50 - 4.9t²
B. To reach the ground
h(t) = 0
So
50-4.9t²= 0
t = √ (50/4.9)
= 3.2s
C. Using
V = u+ gt
U= 0
V= - 9.8(3.2)
= 31.4m/s
D. If u = -9m/s
Then s = ut + 1/2gt²
5t- 1/2gt²
But distance from the ground is
=.> 50-5t- 4.8t²= 0
So t solving the quadratic equation
t= 3.58s
(a) The distance of the stone above the ground level at time t is [tex]h(t) = 50 - 4.9t^2[/tex]
(b) The time taken for the stone to strike the ground is 3.19 s.
(c) The velocity of the stone when it strikes the ground is 31.4 m/s.
(d) The time taken for the stone to reach the ground when thrown at the given speed is 2.41 s.
The given parameters;
height above the ground, h₀ = 50 mThe distance of the stone above the ground level at time t is calculated as;
[tex]h(t) = h_0 - ut - \frac{1}{2} gt^2\\\\h(t) = 50 - 0 -0.5\times 9.8t^2\\\\h(t) = 50 - 4.9t^2[/tex]
The time taken for the stone to strike the ground is calculated as;
[tex]t = \sqrt{\frac{2h}{g} } \\\\t = \sqrt{\frac{2\times 50}{9.8} } \\\\t = 3.19 \ s[/tex]
The velocity of the stone when it strikes the ground is calculated as;
[tex]v =u + gt\\\\v = 0 + 3.2 \times 9.8\\\\v = 31.4 \ m/s[/tex]
The time taken for the stone to reach the ground when thrown at speed of 9 m/s is calculated as;
[tex]50 = 9t + \frac{1}{2} (9.8)t^2\\\\50 = 9t + 4.9t^2\\\\4.9t^2 + 9t - 50 = 0\\\\a = 4.9 \, \ b = 9, \ \ c = -50\\\\solve \ the \ quadratic \ equation\ using \ formula \ method\\\\t = \frac{-b \ \ + /- \ \ \sqrt{b^2 - 4ac} }{2a} \\\\t = \frac{-9 \ \ + /- \ \ \sqrt{(9)^2 - 4(4.9 \times -50)} }{2(4.9)} \\\\t = 2.41 \ s \ \ or \ \ - 4.24 \ s[/tex]
Thus, the time taken for the stone to reach the ground when thrown at the given speed is 2.41 s.
Learn more here:https://brainly.com/question/9527588
You are performing an experiment that requires the highest-possible magnetic energy density in the interior of a very long current-carrying solenoid. Which of the following adjustments increases the energy density?a. Increasing only the length of the solenold while keeping the turns per unit lengh flxed. b. Increasing the number of turns per unit length on the solenold. c. Increasing the cross-sectional area of the solenoid. d. None of these. e. Increasing the current in the solenoid.
Answer:
The correct choice is B & E.
Explanation:
A solenoid is a coil of wire (usually copper) which is used as an electromagnet. Solenoids are used to convert electrical energy to mechanical energy. When this type of device is created it is also called a solenoid. One can increase the energy density within the solenoid or the coil by upping the electric current in the coil.
Cheers!
A wire carries current in the plane of this paper toward the top of the page. The wire experiences a ma netic force toward the right edge of the page. The direction of the magnetic field causing this force is:
A. in the plane of the page and toward the left edge
B. in the plane of the page and toward the bottom edge
C. upward out of the page
D. downward into the page
Answer:
D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left
Explanation:
The magnetic force on a conductor is given by
F = i L x B
bold letters indicate vectors. We can write this expression in the form of magnitudes
F = i L B sin θ
The direction of the force can be found by the rule of the right hand, the thumb points in the direction of the current, the fingers extended in the direction of the magnetic field and the palm gives the direction of the force
Let's apply this expression to the case presented.
A) False. In this case the force is out of the page and is in contradiction with the real force
B) False. In this case the force is zero since the displacement of the current and the field would be parallel
C) False. In this case the force is to the left
D) True. In this case the thumb goes up the page, the fingers are extended out of the page and the palm points to the left
As a skydiver falls, his potential energy ___ and his kinetic energy __
increases,increases
increases,decreases
decreases,increases
decreases, decreases
Answer:
Hey there!
PE=mgh, so as height decreases, so does the potential energy.
KE=mv^2, so as velocity increases, kinetic energy increases.
Thus, the correct answer would be Decreases, Increases.
Let me know if this helps :)
A uniform meter stick is hung at its center from a thin wire. It is twisted and oscillates with a period of 5 s. The meter stick is then sawed off to a length of 0.76 m, rebalanced at its center, and set into oscillation. With what period does it now oscillate?
Answer:
The new time period is [tex]T_2 = 3.8 \ s[/tex]
Explanation:
From the question we are told that
The period of oscillation is [tex]T = 5 \ s[/tex]
The new length is [tex]l_2 = 0.76 \ m[/tex]
Let assume the original length was [tex]l_1 = 1 m[/tex]
Generally the time period is mathematically represented as
[tex]T = 2 \pi \sqrt{ \frac{ I }{ mgh } }[/tex]
Now I is the moment of inertia of the stick which is mathematically represented as
[tex]I = \frac{m * l^2 }{12 }[/tex]
So
[tex]T = 2 \pi \sqrt{ \frac{ m * l^2 }{12 * mgh } }[/tex]
Looking at the above equation we see that
[tex]T \ \ \ \alpha \ \ \ l[/tex]
=> [tex]\frac{ T_2 }{T_1} = \frac{l_2}{l_1}[/tex]
=> [tex]\frac{ T_2}{5} = \frac{0.76}{1}[/tex]
=> [tex]T_2 = 3.8 \ s[/tex]
The magnitude of the magnetic field at point P for a certain electromagnetic wave is 2.12 μT. What is the magnitude of the electric field for that wave at P? (c = 3.0 × 108 m/s)
Answer:
The electric field is [tex]E = 636 \ V/m[/tex]
Explanation:
From the question we are told that
The magnitude of magnetic field is [tex]B = 2.12 \mu T = 2.12*10^{-6} \ T[/tex]
The value for speed of light is [tex]c = 3.0 *10^8 \ m/s[/tex]
Generally the magnitude of the electric field at point P is
[tex]E = B * c[/tex]
substituting values
[tex]E = 2.12 *10^{-6} * 3.0 *10^{8}[/tex]
[tex]E = 636 \ V/m[/tex]
The magnitude of electric field for the wave at point P is 636 V/m.
Given data:
The strength of magnetic field at point P is, [tex]B = 2.12 \;\rm \mu T=2.12 \times 10^{-6} \;\rm T[/tex].
The speed of light is, [tex]c = 3.0 \times 10^{8} \;\rm m/s[/tex].
The given problem is based on the concept of electric field and magnetic field. The electromagnetic wave works on the principle of oscillating magnetic field and electric field at the same region. We can find any of the two using the expression,
[tex]E = B \times c[/tex]
here,
E is the strength of electric field.
Solving as,
[tex]E = (2.12 \times 10^{-6}) \times (3 \times 10^{8})\\\\E = 636 \;\rm V/m[/tex]
Thus, we can conclude that the magnitude of electric field for the wave at point P is 636 V/m.
Learn more about the electric field here:
https://brainly.com/question/15800304
A radiation worker is subject to a dose of 200 mrad/h of maximum QF neutrons for one 40 h work week. How many times the yearly allowable effective dose did she receive?
Answer:
16 times.
Explanation:
The rate of the radiation dose is , R = 200 ×10^{-3} rad/hr
Time consumed, t = 40 hr
The magnitude of Q.F for the neutrons, Q.F = 2
Thus the effective radiation dose is:
[tex]R_{Eff} = Rt(Q.F) \\= 200 \times 10^{-3} \frac{rad}{hr} (40hr)(2) \\= 16 \ rad[/tex]
Thus, the effective dose allowable yearly = 16 times
Are Quantum Physics, Quantum mechanics,Quantum Engagement same?
or, Do they branch of each others
Answer:
The topic of quantum entanglement is at the heart of the disparity between classical and quantum physics: entanglement is a primary feature of quantum mechanics lacking in classical mechanics. ... In the case of entangled particles, such a measurement will affect the entangled system as a wholeExplanation:
Answer:
quantum entanglement is thought to be one of the trickiest concepts in science, but the core issues are simple. And once understood, entanglement opens up a richer understanding of concepts such as the “many worlds” of quantum theory.
Explanation:
Calcular la resistencia de una varilla de grafito de 170 cm de longitud y 60 mm2. Resistividad grafito 3,5 10-5 Ωm
Answer:
R = 0.992 Ω
Explanation:
En esta pregunta, dada la información que contiene, debemos calcular la resistencia de la varilla de grafito.
Matemáticamente,
Resistencia = (resistividad * longitud) / Área De la pregunta;
Resistividad = 3,5 * 10 ^ -5 Ωm
longitud = 170 cm = 1,7 m
Área = 60 mm ^ 2 = 60/1000000 = 6 * 10 ^ -5 m ^ 2
Conectando estos valores a la ecuación anterior, tenemos;
Resistencia = (3.5 * 10 ^ -5 * 1.7) / (6 * 10 ^ -5) =
(3.5 * 1.7) / 6 = 0.992 Ω
A locomotive is pulling three train cars along a level track with a force of 100,000N. The car next to the locomotive has a mass of 80,000kg, next one, 50,000kg, and the last one, 70,000 kg. you can neglect the friction on the cars being pulled.
A) what if the magnitude of the force between that the 80,000-kg car exerts on the 50,000-kg car?
B) what is the magnitude of the force that the 50,000-kg car exerts on the 70,000-kg car?
Answer:
a) 60000 N
b) 35000 N
Explanation:
Force from locomotive = 100000 N
mass of first car = 80000 kg
mass of second car = 50000 kg
mass of third car = 70000 kg
friction is neglected in this system
Total mass of the cars = 80000 + 50000 + 70000 = 200000 kg
All the car in the system will accelerate at the same rate since they are pulled by the same force
We know that force F = ma
where
a is the acceleration of the cars
m is the total mass in the system
from this we can say that
a = F/m
a = 100000/200000 = 0.5 m/s^2
a) The total mass involved in this case = mass of the last two cars after the 80000 kg car = 50000 + 70000 = 120000 kg
therefore force exerted F = ma
F = 0.5 x 120000 = 60000 N
b) The total mass in this case = mass of the third car only = 70000 kg
F = ma
F = 70000 x 0.5 = 35000 N
