A child is trying to throw a ball over a fence. She gives the ball an initial speed of 8.0 m/s at an angle of 40° above the horizontal. The ball leaves her hand 1.0 m above the ground and the fence is 2.0 m high. The ball just clears the fence while still traveling upwards and experiences no significant air resistance. How far is the child from the fence?

Answers

Answer 1

Answer:

the child is 1.581 m far from the fence

Explanation:

The diagrammatic illustration that give a better view of what the question denote can be seen in the image attached below.

From the image attached below, let assume that the release point is the origin, then equation of the motion (x) is as follows:

[tex]x - x_o = u_xt[/tex]

[tex]\mathtt{x = u_xt \ \ \ since (x_o = 0)}[/tex]  ---- (1)

the equation of the motion y is :

[tex]\mathtt{y - y_o =u_yt - 0.5 gt^2}[/tex]

[tex]\mathtt{y = u_yt-4.9t^2 \ \ \ since (y_o =0)}[/tex]

[tex]\mathtt{ 1= (u \ sin 40^0)t -4.9 \ t^2 }[/tex]

[tex]\mathtt{1 = 8 sin 40^0 t - 4.9 t^2}[/tex]

[tex]\mathtt{1 = 5.14t - 4.9t^2}[/tex]

[tex]\mathtt{4.9t^2 - 5.14t +1 = 0}[/tex]

By using the quadratic formula, we have;

[tex]\mathtt{ \dfrac{ -b \pm \sqrt{b^2 - 4ac}}{2a}} }[/tex]

where;

a = 4.9,   b = -5.14     c = 1

[tex]= \mathtt{ \dfrac{ -(-5.14) \pm \sqrt{(-5.14)^2 - 4(4.9)(1)}}{2(4.9)}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{26.4196 -19.6}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14 \pm \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ \sqrt{6.8196}}{9.8} \ \ OR \ \ \dfrac{ 5.14- \sqrt{6.8196}}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 5.14+ 2.6114}{9.8} \ \ OR \ \ \dfrac{ 5.14- 2.6114}{9.8}} }[/tex]

[tex]= \mathtt{ \dfrac{ 7.7514}{9.8} \ \ OR \ \ \dfrac{ 2.5286}{9.8}} }[/tex]

[tex]= \mathbf{ 0.791 \ \ OR \ \ 0.258} }[/tex]

In as much as the ball is traveling upward, then we consider t= 0.258sec.

From equation (1)

[tex]\mathtt{x = u_x(0.258)}[/tex]

[tex]\mathtt{x = ucos 40^0 (0.258)}[/tex]

[tex]\mathtt{x = 8 \ cos 40^0 (0.258)}[/tex]

[tex]\mathbf{x = 1.581 \ m}[/tex]

Thus, the child is 1.581 m far from the fence

A Child Is Trying To Throw A Ball Over A Fence. She Gives The Ball An Initial Speed Of 8.0 M/s At An

Related Questions

A solid block is attached to a spring scale. When the block is suspended in air, the scale reads 21.2 N; when it is completely immersed in water, the scale reads 18. 2 N. What are the volume and density of the block?

Answers

Answer:

7066kg/m³

Explanation:

The forces in these cases (air and water) are: Fa =mg =ρbVg Fw =(ρb −ρw)Vg where ρw = 1000 kg/m3 is density of water and ρb is density of the block and V is its density. We can find it from this two equations:

Fa /Fw = ρb / (ρb −ρw) ρb = ρw (Fa /Fa −Fw) =1000·(1* 21.2 /21.2 − 18.2)

= 7066kg/m³

Explanation:

Answer:

The volume of the block is 306 cm³

The density of the block is 7.07 g/cm³

Explanation:

Given;

weight of block in air, [tex]W_a[/tex] = 21.2 N

Weight of block in water, [tex]W_w[/tex] = 18.2 N

Mass of the block in air;

[tex]W_a = mg[/tex]

21.2 = m x 9.8

m = 21.2 / 9.8

m = 2.163 kg

mass of the block in water;

[tex]W_w = mg[/tex]

18.2 = m x 9.8

m = 18.2 / 9.8

m = 1.857 kg

Apply Archimedes principle

Mass of object in air  - mass of object in water = density of water   x  volume                  of object

2.163 kg - 1.857 kg = 1000 kg/m³ x Volume of block

0.306 kg = 1000 kg/m³ x Volume of block

Volume of the block = [tex]\frac{0.306 \ kg}{1000 \ kg/m^3}[/tex]

Volume of the block = 3.06 x 10⁻⁴ m³

Volume of the block = 306 cm³

Determine the density of the block

[tex]Density = \frac{mass}{volume} \\\\Density =\frac{2163 \ g}{306 \ cm^3} \\\\Density = 7.07 \ g/cm^3[/tex]

c) If the ice block (no penguins) is pressed down even with the surface and then released, it will bounce up and down, until friction causes it to settle back to the equilibrium position. Ignoring friction, what maximum height will it reach above the surface

Answers

Answer:

y = 20.99 V / A

there is no friction    y = 20.99 h

Explanation:

Let's solve this exercise in parts: first find the thrust on the block when it is submerged and then use the conservation of energy

when the block of ice is submerged it is subjected to two forces its weight  hydrostatic thrust

         

              F_net= ∑F = B-W

the expression stop pushing is

              B = ρ_water g V_ice

where rho_water is the density of pure water that we take as 1 10³ kg / m³ and V is the volume d of the submerged ice

We can write the weight of the body as a function of its density rho_hielo = 0.913 10³ kg / m³

             W = ρ-ice g V

              F_net = (ρ_water - ρ_ ice) g V

this is the net force directed upwards, we can find the potential energy with the expression

            F = -dU / dy

            ΔU = - ∫ F dy

            ΔU = - (ρ_water - ρ_ ice) g ∫ (A dy) dy

            ΔU = - (ρ_water - ρ_ ice) g A y² / 2

we evaluate between the limits y = 0,  U = 0, that is, the potential energy is zero at the surface

             U_ice = (ρ_water - ρ_ ice) g A y² / 2

now we can use the conservation of mechanical energy

starting point. Ice depth point

             Em₀ = U_ice = (ρ_water - ρ_ ice) g A y² / 2

final point. Highest point of the block

             [tex]Em_{f}[/tex] = U = m g y

as there is no friction, energy is conserved

            Em₀ = Em_{f}

            (ρ_water - ρ_ ice) g A y² / 2 = mg y

let's write the weight of the block as a function of its density

            ρ_ice = m / V

            m = ρ_ice V

we substitute

             (ρ_water - ρ_ ice) g A y² / 2 = ρ_ice V g y

              y = ρ_ice / (ρ_water - ρ_ ice) 2 V / A

let's substitute the values

             y = 0.913 / (1 - 0.913) 2 V / A

             y = 20.99 V / A

This is the height that the lower part of the block rises in the air, we see that it depends on the relationship between volume and area, which gives great influence if there is friction, as in this case it is indicated that there is no friction

                V / A = h

where h is the height of the block

                 y = 20.99 h

What is the thinnest soap film (excluding the case of zero thickness) that appears black when illuminated with light with a wavelength of 580 nm

Answers

Answer:

Explanation:

In case of soap film , light gets reflected from denser medium , hence interference takes place between two waves , one reflected from upper and second from lower surface . For destructive interference the condition is

2μt = nλ where μ is refractive index of water , t is thickness , λ is wavelength of light and n is an integer .

2 x 1.34 x t = 1  x 580

t = 216.42 nm .

Thickness must be 216.42 nm .

Can abnormality exist outside of a cultural context

Answers

you should search this up and put your own thoughts into it, it’s always good to learn something new!!

A typical ten-pound car wheel has a moment of inertia of about 0.35kg *m2. The wheel rotates about the axle at a constant angular speed making 70.0 full revolutions in a time interval of 4.00 seconds. What is the rotational kinetic energy K of the rotating wheel? Express answer in Joules

Answers

Answer:

The  rotational kinetic energy is  [tex]K = 2116.3 \ J[/tex]

Explanation:

From the question we are told that

    The moment of inertia  is  [tex]I = 0.35 \ kg \cdot m^2[/tex]

    The number of revolution is N  =  70 revolution

     The  time taken is  t  =  4.0  s

   

Generally the angular velocity is mathematically represented as

      [tex]w = \frac{2 \pi N }{t }[/tex]

substituting values

      [tex]w = \frac{2* 3.142 * 70 }{4 }[/tex]

       [tex]w = 109.97 \ rad/s[/tex]

     

The rotational kinetic energy K i mathematically represented as

       [tex]K = \frac{1}{ 2} * I * w^2[/tex]

substituting values

       [tex]K = \frac{1}{ 2} * 0.35 * (109.97)^2[/tex]

       [tex]K = 2116.3 \ J[/tex]

Exercise 2.4.5: Suppose we add possible friction to Exercise 2.4.4. Further, suppose you do not know the spring constant, but you have two reference weights 1 kg and 2 kg to calibrate your setup. You put each in motion on your spring and measure the frequency. For the 1 kg weight you measured 1.1 Hz, for the 2 kg weight you measured 0.8 Hz. a) Find k (spring constant) and c (damping constant). Find a formula for the mass in terms of the frequency in Hz. Note that there may be more than one possible mass for a given frequency. b) For an unknown object you measured 0.2 Hz, what is the mass of the object? Suppose that you know that the mass of the unknown object is more than a kilogram.

Answers

Answer:

a) k = 95.54 N / m,   c =   19.55 , b)      m₃ = 0.9078 kg

Explanation:

In a simple harmonic movement with friction, we can assume that this is provided by the speed

          fr = -c v

when solving the system the angular value remains

          w² = w₀² + (c / 2m)²

They give two conditions

1) m₁ = 1 kg

     f₁ = 1.1 Hz

the angular velocity is related to frequency

         w = 2π f₁

Let's find the angular velocity without friction is

         w₂ = k / m₁

we substitute

        (2π f₁)² = k / m₁ + (c / 2m₁)²

2) m₂ = 2 kg

    f₂ = 0.8 Hz

        (2π f₂)² = k / m₂ + (c / 2m₂)²

we have a system of two equations with two unknowns, so we can solve it

we solve (c / 2m)² is we equalize the expression

           (2π f₁)² - k / m₁ = (2π f₂²) 2 - k / m₁

           k (1 / m₂ - 1 / m₁) = 4π² (f₂² - f₁²)

           k = 4π² (f₂² -f₁²) / (1 / m₂ - 1 / m₁)

a) Let's calculate

           k = 4 π² (0.8² -1.1²) / (½ -1/1)

           k = 39.4784 (1.21) / (-0.5)

           k = 95.54 N / m

now we can find the constant of friction

              (2π f₁) 2 = k / m₁ + (c / 2m₁)²

           c2 = ((2π f₁)² - k / m₁) 4m₁²

           c2 = (4ππ² f₁² - k / m₁) 4 m₁²

let's calculate

           c² = (4π² 1,1² - 95,54 / 1) 4 1²

           c² = (47.768885 - 95.54) 8

           c² = -382.1689

           c =   19.55    

b) f₃ = 0.2 Hz

   m₃ =?

              (2πf₃)² = k / m₃ + (c / 2m₃) 2

we substitute the values

              (4π² 0.2²) = 95.54 / m₃ + 382.1689 2/4 m₃²

              1.579 = 95.54 / m₃ + 95.542225 / m₃²

let's call

              x = 1 / m₃

              x² = 1 / m₃²

- 1.579 + 95.54 x + 95.542225 x² = 0

              60.5080 x² + 60.5080 x -1 = 0

                x² + x - 1.65 10⁻² = 0

                  x = [1 ±√ (1- 4 (-1.65 10⁻²)] / 2

                  x = [1 ± 1.03] / 2

                  x₁ = 1.015 kg

                  x₂ = -0.015 kg

Since the mass must be positive we eliminate the second results

                  x₁ = 1 / m₃

                 m₃ = 1 / x₁

                  m₃ = 1 / 1.1015

             

Given three resistors of different values, how many possible resistance values could be obtained by using one or more of the resistors?

Answers

Answer:

8 possible combinations

Assuming R 1, R 2 and R 3 be three different Resistance

1- all three in series

2-all three in parallel

3- R 1 and R 2 in series and parallel with R 3

4-R 1 and R 3 in series and parallel with R 2

5-R 2 and R 3 in series and parallel with R 1

6- R 1 and R 2

in parallel and series with R 3

7-R 1 and R 3 in parallel and series with R 2

8-R 2 and R 3 in V with R 1

A resistor and an inductor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the inductor is

Answers

Answer:

The voltage is equal to the batteries terminal voltage

Explanation:

Explanation:

) Calculate current passing in an electrical circuit if you know that the voltage is 8 volts and the resistance is 10 ohms

Answers

Explanation:

Hey, there!

Here, In question given that,

potential difference (V)= 8V

resistance (R)= 10 ohm

Now,

According to the Ohm's law,

V= R×I { where I = current}

or, I = V/R

or, I = 8/10

Therefore, current is 4/5 A or 0.8 A.

(A= ampere = unit of current).

Hope it helps...

How wide is the central diffraction peak on a screen 2.20 mm behind a 0.0328-mmmm-wide slit illuminated by 588-nmnm light?

Answers

Answer:

[tex]y = 0.0394 \ m[/tex]

Explanation:

From the question we are told that

        The  distance of the screen is  [tex]D = 2.20 \ m[/tex]

       The distance of separation of the slit is  [tex]d = 0.0328 \ mm = 0.0328*10^{-3} \ m[/tex]

        The  wavelength of light is  [tex]\lambda = 588 \ nm = 588 *10^{-9} \ m[/tex]

Generally the condition for constructive interference is

            [tex]dsin\theta = n * \lambda[/tex]

=>        [tex]\theta = sin^{-1} [ \frac{ n * \lambda }{d } ][/tex]

here n = 1 because we are considering the central diffraction peak

=>        [tex]\theta = sin^{-1} [ \frac{ 1 * 588*10^{-9} }{0.0328*10^{-3} } ][/tex]

=>       [tex]\theta = 1.0274 ^o[/tex]

Generally the width of central diffraction peak on a screen is mathematically evaluated as

           [tex]y = D tan (\theta )[/tex]

substituting values

        [tex]y = 2.20 * tan (1.0274)[/tex]

        [tex]y = 0.0394 \ m[/tex]

A thermos bottle works well because:

a. its glass walls are thin
b. silvering reduces convection
c. vacuum reduces heat radiation
d. silver coating is a poor heat conductor
e. none of the above

Answers

Answer:

A thermos bottle works well because:

A) Its glass walls are thin

Answer:

A thermos bottle works well because:

C

Vacuum reduces heat radiation

When a monochromatic light of wavelength 433 nm incident on a double slit of slit separation 6 µm, there are 5 interference fringes in its central maximum. How many interference fringes will be in the central maximum of a light of wavelength 632.9 nm for the same double slit?

Answers

Answer:

The number of interference fringes is  [tex]n = 3[/tex]

Explanation:

From the question we are told that

     The wavelength is  [tex]\lambda = 433 \ nm = 433 *10^{-9} \ m[/tex]

      The distance of separation is  [tex]d = 6 \mu m = 6 *10^{-6} \ m[/tex]

       The  order of maxima is m =  5

       

The  condition for constructive interference is

       [tex]d sin \theta = n \lambda[/tex]

=>     [tex]\theta = sin^{-1} [\frac{5 * 433 *10^{-9}}{ 6 *10^{-6}} ][/tex]

=>    [tex]\theta = 21.16^o[/tex]

So at  

      [tex]\lambda_1 = 632.9 nm = 632.9*10^{-9} \ m[/tex]

   [tex]6 * 10^{-6} * sin (21.16) = n * 632.9 *10^{-9}[/tex]

=>    [tex]n = 3[/tex]

   

Scouts at a camp shake the rope bridge they have just crossed and observe the wave crests to be 9.70 m apart. If they shake the bridge twice per second, what is the propagation speed of the waves (in m/s)?

Answers

Answer:

The speed of the wave is 19.4 m/s

Explanation:

The wave's crest to crest distance (the wavelength of this rope's wave) λ= 9.70 m

The bridge is shaken twice, meaning that two wavelengths passed a given point on the rope per sec. The frequency of a wave is the amount of that wave that passes a given point in a second.

this means that the frequency f = 2 Hz

The speed of a wave = fλ = 9.70 x 2 = 19.4 m/s

A straight wire that is 0.56 m long is carrying a current of 2.6 A. It is placed in a uniform magnetic field, where it experiences a force of 0.24 N. The wire makes an angle of 900 with the magnetic field. What is the magnitude of the magnetic field

Answers

Answer:

0.165Tesla

Explanation:

The Force experienced by the wire in the uniform magnetic field is expressed as F = BILsin∝ where;

B is the magnetic field (in Tesla)

I is the current (in amperes)

L is the length of the wire (in meters)

∝ is the angle that the conductor makes with the magnetic field.

Given parameters

L = 0.56 m

I = 2.6A

F = 0.24N

∝  = 90°

Required

magnitude of the magnetic field (B)

Substituting the given values into the formula given above we will have;

F = BILsin∝

0.24 = B * 2.6 * 0.56 sin90°

0.24 =  B * 2.6 * 0.56 (1)

0.24 = 1.456B

1.456B = 0.24

Dividing both sides by 1.456 will give;

1.456B/1.456 = 0.24/1.456

B ≈ 0.165Tesla

Hence the magnitude of the magnetic field is approximately 0.165Tesla

Structures on a bird feather act like a diffraction grating having 8500 lines per centimeter. What is the angle of the first-order maximum for 577 nm light shone through a feather?

Answers

Answer:

29.5°

Explanation:

To find the distance d

d = 1E10^-2/8500lines

= 1.17x 10-6m

But wavelength in first order maximum is 577nm

and M = 1

So

dsin theta= m. Wavelength

Theta= sin^-1 (m wavelength/d)

= Sin^-1 ( 1* 577 x10^-8m)/1.17*10^-6

= 493*10^-3= sin^-1 0.493

Theta = 29.5°

There are 5510 lines per centimeter in a grating that is used with light whose wavelegth is 467 nm. A flat observation screen is located 1.03 m from the grating. What is the minimum width that the screen must have so the centers of all the principal maxima formed on either side of the central maximum fall on the screen

Answers

Answer:

1.696 nm

Explanation:

For a diffraction grating, dsinθ = mλ where d = number of lines per metre of grating = 5510 lines per cm = 551000 lines per metre and λ = wavelength of light = 467 nm = 467 × 10⁻⁹ m. For a principal maximum, m = 1. So,

dsinθ = mλ = (1)λ = λ

dsinθ = λ

sinθ = λ/d.

Also tanθ = w/D where w = distance of center of screen to principal maximum and D = distance of grating to screen = 1.03 m

From trig ratios 1 + cot²θ = cosec²θ

1 + (1/tan²θ) = 1/(sin²θ)

substituting the values of sinθ and tanθ we have

1 + (D/w)² = (d/λ)²

(D/w)² = (d/λ)² - 1

(w/D)² = 1/[(d/λ)² - 1]

(w/D) = 1/√[(d/λ)² - 1]

w = D/√[(d/λ)² - 1] = 1.03 m/√[(551000/467 × 10⁻⁹ )² - 1] = 1.03 m/√[(1179.87 × 10⁹ )² - 1] = 1.03 m/1179.87 × 10⁹  = 0.000848 × 10⁻⁹ = 0.848 × 10⁻¹² m = 0.848 nm.

w is also the distance from the center to the other principal maximum on the other side.

So for both principal maxima to be on the screen, its minimum width must be 2w = 2 × 0.848 nm = 1.696 nm

So, the minimum width of the screen must be 1.696 nm

The velocity function (in meters per second) is given for a particle moving along a line. Find the total distance traveled by the particle during the given interval

Answers

Answer:

s=((vf+vi)/2)t vf is final velocity and vi is initial velocity

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?

Answers

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

       

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

A jumbo jet has a mass of 100,000 kg. The thrust of each of its four engines is 50,000 N. What is the jet's acceleration in meters per second squared right before taking off? Neglect air resistance and friction.

Answers

Answer:

The acceleration is   [tex]a =2\ m/s^2[/tex]

Explanation:

From the question we are told that

       The  mass of the jumbo jet is  [tex]m_j = 100000\ kg[/tex]

        The thrust is  [tex]F_k = 50000 \ N[/tex]

Generally given that the jet has four engines the total thrust is  

        [tex]F_t = 4 * F_k[/tex]

substituting values

       [tex]F_t = 4 * 50000[/tex]

      [tex]F_t = 200000 \ N[/tex]

Generally the acceleration of the is mathematically represented as

         [tex]a = \frac{F_t}{m}[/tex]

substituting values

       [tex]a =2 \frac{N}{kg}[/tex]

Now  

        [tex]N = kg \cdot m/s^2[/tex]

Hence

         [tex]a =2 \frac{kg * \cdot m/s^2}{kg}[/tex]

        [tex]a =2\ m/s^2[/tex]

Water flows at speed v in a pipe of radius R. At what speed does the water flow through a constriction in which the radius of the pipe is R/3

Answers

Answer:

   v₂ = 9 v

Explanation:

For this exercise in fluid mechanics, let's use the continuity equation

           v₁ A₁ = v₂ A₂

where v is the velocity of the fluid, A the area of ​​the pipe and the subscripts correspond to two places of interest.

The area of ​​a circle is

           A = π R²

let's use the subscript 1 for the starting point and the subscript 2 for the part with the constraint

     

In this case v₁ = v and the area is

            A₁ = π R²

in the second point

           A₂= π (R / 3)²

we substitute in the continuity equation

           v π R² = v₂ π R² / 9

            v = v₂ / 9

           

            v₂ = 9 v

A solenoid inductor has an emf of 0.80 V when the current through it changes at the rate 10.0 A/s. A steady current of 0.20 A produces a flux of 8.0 μWb per turn.

Required:
How many turns does the inductor have?

Answers

Answer:

The number of turns of the inductor is 2000 turns.

Explanation:

Given;

emf of the inductor, E = 0.8 V

the rate of change of current with time, dI/dt = 10 A/s

steady current in the solenoid, I = 0.2 A

flux per turn, Ф = 8.0 μWb per

Determine the inductance of the solenoid, L

E = L(dI/dt)

L = E / (dI/dt)

L = 0.8 / (10)

L = 0.08 H

The inductance of the solenoid is given by;

[tex]L = \frac{\mu_o N^2 A}{l}[/tex]

Also, the magnetic field of the solenoid is given by;

[tex]B = \frac{\mu_o NI}{l}[/tex]

I is 0.2 A

[tex]B = \frac{\mu_oN(0.2)}{l} = \frac{0.2\mu_o N}{l}[/tex]

[tex]\frac{B}{0.2 } = \frac{\mu_o N}{l}[/tex]

[tex]L = \frac{\mu_o N^2 A}{l} \\\\L = \frac{\mu_o N }{l} (NA)\\\\L = \frac{B}{0.2} (NA)\\\\L = \frac{BA}{0.2} (N)[/tex]

But Ф = BA

[tex]L = \frac{\phi N}{0.2} \\\\\phi N = 0.2 L\\\\N = \frac{0.2 L}{\phi} \\\\N = \frac{0.2 *0.08}{8*10^{-6}}\\\\N = 2000 \ turns[/tex]

Therefore, the number of turns of the inductor is 2000 turns.

This question involves the concepts of magnetic flux, magnetic field, and inductance.

The inductor has "2000" turns.

The magnetic field due to an inductor coil is given as follows:

[tex]B=\frac{\mu_o NI}{L}\\\\[/tex]

where,

B = magnetic field

μ₀ = permeability of free space \

N = No. of turns

I = current = 0.2 A

L = length of inductor

Therefore,

[tex]\frac{\mu_oN}{L}=\frac{B}{0.2\ A}---------- eqn(1)[/tex]

Now, the inductance of a solenoid is given by the following formula:

[tex]E = L\frac{dI}{dt}\\\\L = \frac{E}{\frac{dI}{dt}}[/tex]

The inductance of solenoid can also be given using the following formula:

[tex]L = \frac{\mu_o N^2A}{L}[/tex]

comparing both the formulae, we get:

[tex]\frac{E}{\frac{dI}{dt}}= \frac{\mu_oN^2A}{L}\\\\E=\frac{dI}{dt}\frac{\mu_oN}{l}(NA)\\\\using\ eqn (1):\\\\E=\frac{dI}{dt}\frac{B}{0.2}(NA)\\\\[/tex]

where,

BA = magnetic flux = [tex]\phi[/tex] = 8 μWb/turn = 8 x 10⁻⁶ Wb/turn

N = No. of turns = ?

E = E.M.F = 0.8 volts

[tex]\frac{dI}{dt}[/tex] = rate of change in current = 10 A/s

Therefore,

[tex]0.8=(10)\frac{8\ x\ 10^{-6}}{0.2}N\\\\N=\frac{(0.8)(0.2)}{8\ x\ 10^{-5}}[/tex]

N = 2000 turns

Learn more about magnetic flux here:

brainly.com/question/24615998?referrer=searchResults

The attached picture shows the magnetic flux.

When the current in a toroidal solenoid is changing at a rate of 0.0200 A/s, the magnitude of the induced emf is 12.7 mV. When the current equals 1.50 A, the average flux through each turn of the solenoid is 0.00458 Wb. How many turns does the solenoid have?

Answers

Answer:

[tex]N = 208 \ turns[/tex]

Explanation:

From the question we are told that

    The  rate of  current change is  [tex]\frac{di }{dt} = 0.0200 \ A/s[/tex]

    The  magnitude of the induced emf is  [tex]\epsilon = 12.7 \ mV = 12.7 *10^{-3} \ V[/tex]

     The  current is  [tex]I = 1.50 \ A[/tex]

      The  average  flux is  [tex]\phi = 0.00458 \ Wb[/tex]

Generally the number of  turns the number of turn the solenoid has is mathematically represented as  

            [tex]N = \frac{\epsilon_o * I}{ \phi * \frac{di}{dt} }[/tex]

substituting values

           [tex]N = \frac{ 12.7*10^{-3} * 1.50 }{ 0.00458 * 0.0200 }[/tex]

            [tex]N = 208 \ turns[/tex]

       

A circular loop of wire of area 25 cm2 lies in the plane of the paper. A decreasing magnetic field B is coming out of the paper. What is the direction of the induced current in the loop?

Answers

Answer:

counterclockwise

Explanation:

given data

area = 25 cm²

solution

We know that a changing magnetic field induces the current and induced emf is express as

[tex]\epsilon = -N \frac{d \phi }{dt}[/tex]     ..................................1

and we will get here direction of the induced current in the loop that is express by the Lens law that state that the direction of induces current is such that the magnetic flux due to the induced current opposes the change in magnetic flux due to the change in magnetic field

so when magnetic field decrease and point coming out of the paper.

so induced current in the loop will be counterclockwise

In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?

Answers

Answer:

The wavelength is  [tex]\lambda = 419 \ nm[/tex]

Explanation:

From the question we are told that

   The  distance of separation is   [tex]d = 3.34 *10^{-5} \ m[/tex]

   The  distance of the screen is  [tex]D = 3.30 \ m[/tex]

      The  order of the fringe is  n =  7

     The distance of separation of  fringes is y =  29.0 cm = 0.29 m

   

Generally the wavelength of the light is mathematically represented as

          [tex]\lambda = \frac{y * d }{ n * D}[/tex]

substituting values

         [tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]

        [tex]\lambda = 4.19*10^{-7}\ m[/tex]

        [tex]\lambda = 419 \ nm[/tex]

A long solenoid consists of 1700 turns and has a length of 0.75 m.The current in the wire is 0.48 A. What is the magnitude of the magnetic field inside the solenoid

Answers

Answer:

1.37 ×10^-3 T

Explanation:

From;

B= μnI

μ = 4π x 10-7 N/A2

n= number of turns /length of wire = 1700/0.75 = 2266.67

I= 0.48 A

Hence;

B= 4π x 10^-7 × 2266.67 ×0.48

B= 1.37 ×10^-3 T

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W

Answers

Complete Question

At what rate must Uranium 235 undergo fission by neutron bombardment to generate energy at a rate of 100 W (1 W = 1 J/s)? Assume each fission reaction releases 200 MeV of energy.

Answer

a. Approximately [tex]5*10^{10}[/tex] fissions per second.

b. Approximately [tex]6*10^{12 }[/tex]fissions per second.

c. Approximately [tex]4*10^{11}[/tex] fissions per second.

d. Approximately [tex]3*10^{12}[/tex] fissions per second.

e. Approximately[tex]3*10^{14}[/tex] fissions per second.

Answer:

The correct option is  d

Explanation:

From the question we are told that

       The energy released by each fission reaction [tex]E = 200 \ MeV = 200 *10^{6} * 1.60 *10^{-19} =3.2*10^{-11} \ J /fission[/tex]

Thus to generated  [tex]100 \ J/s[/tex] i.e  (100 W  ) the rate of fission is  

              [tex]k = \frac{100}{3.2 *10^{-11} }[/tex]

              [tex]k =3*10^{12} fission\ per \ second[/tex]

When using science to investigate physical phenomena, which characteristic of the event must exist? predictable repeatable provable readable

Answers

Answer:

Not sure but I believe predictable.

Explanation:

Phenomena usually consists of :

- A history, a date in which the physical phenomenon has occurred.

- A source, a place or reason to why or where the physical phenomena has occured.

According to this, I want to say predictable.

It is not repeatable, there are one-time phenomenons that have occurred that scientists to this day still have not recorded again such as the Big Bang.

It is not provable. Most of the theories earlier scientists and historians have predicted have not yet been proved. Yet rather, somehow, they have been explored and investigated.

It is not readable. This is self explanatory, some things scientists investigate are not written down, nor read. It starts with a mental theory and then immediately goes to the next phase of investigation.

W is the work done on the system, and K, U, and Eth are the kinetic, potential, and thermal energies of the system, respectively. Any energy not mentioned in the transformation is assumed to remain constant; if work is not mentioned, it is assumed to be zero.

1. Give a specific example of a system with the energy transformation shown.
W→ΔEth

2. Give a specific example of a system with the energy transformation shown.

a. Rolling a ball up a hill.
b. Moving a block of wood across a horizontal rough surface at constant speed.
c. A block sliding on level ground, to which a cord you are holding on to is attached .
d. Dropping a ball from a height.

Answers

Answer:

1) a block going down a slope

2) a) W = ΔU + ΔK + ΔE, b) W = ΔE, c)  W = ΔK, d) ΔU = ΔK

Explanation:

In this exercise you are asked to give an example of various types of systems

1) a system where work is transformed into internal energy is a system with friction, for example a block going down a slope in this case work is done during the descent, which is transformed in part kinetic energy, in part power energy and partly internal energy that is represented by an increase in the temperature of the block.

2)

a) rolling a ball uphill

In this case we have an increase in potential energy, if there is a change in speed, the kinetic energy also increases, if the change in speed is zero, there is no change in kinetic energy and there is a change in internal energy due to the stationary rec in the point of contact

 W = ΔU + ΔK + ΔE

b) in this system work is transformed into internal energy

      W = ΔE

c) There is no friction here, therefore the work is transformed into kinetic energy

    W = ΔK

d) if you assume that there is no friction with the air, the potential energy is transformed into kinetic energy

      ΔU = ΔK

A particle with charge q and momentum p, initially moving along the x-axis, enters a region where a uniform magnetic field* B=(B0)(k) extends over a width x=L. The particle is deflected a distance d in the +y direction as it traverses the field. Determine the magnitude of the momentum (p).

Answers

Answer:

Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

Explanation:

So, from the question, we are given that the charge = q, the momentum = p.

=> From the question We are also given that, "initially, there is movement along the x-axis which then enters a region where a uniform magnetic field* B = (B0)(k) which then extends over a width x = L, the distance = d in the +y direction as it traverses the field."

Momentum,P = mass × Velocity, v -----(1).

We know that for a free particle the magnetic field is equal to the centrepetal force. Thus, we have the magnetic field = mass,.m × (velocity,v)^2 / radius, r.

Radius,r = P × v / B0 -----------------------------(2).

Centrepetal force = q × B0 × v. ----------(3).

(If X = L and distance = d)Therefore, the radius after solving binomially, radius = (d^2 + 2 L^2) / 2d.

Equating Equation (2) and (3) gives;

P = B0 × q × r.

Hence, the Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

Which statement belongs to Dalton’s atomic theory? Atoms have a massive, positively charged center. Atoms cannot be created or destroyed. Atoms can be broken down into smaller pieces. Electrons are located in energy levels outside of the nucleus.

Answers

Answer:

the correct statement is

* atoms cannot be created or destroyed

Explanation:

The Datlon atomic model was proposed in 1808 and represents atoms as the smallest indivisible particle of matter, they were the building blocks of matter and are represented by solid spheres.

Based on the previous descriptive, the correct statement is

* atoms cannot be created or destroyed

Answer:

the Answer is b hope it help

Explanation:

Other Questions
Considera Usted que las condiciones de vulnerabilidad ante un Tsunami son las mismas para todas las poblaciones? Justifique su respuesta con tres argumentaciones. Find the distance between the points P and Q shown. Question 6 options: A. 73 B. 13 C. 5 D. 65 Find the weight of a pine tree that has a circumference of 14 inches and a height of 120 feet. Use the equation: W = b0 + b1(D2H) why did columbus seize the town referred to in the document above? Corporation has found that % of its sales in any given month are credit sales, while the remainder are cash sales. Of the credit sales, Corporation has experienced the following collection pattern: 20% received in the month of the sale 40% received in the month after the sale 24% received two months after the sale 16% of the credit sales are never received November sales for last year were , while December sales were . Projected sales for the next three months are as follows: January sales. . . . . . . . . . . . . . . . $150,000 February sales. . . . . . . . . . . . . . . $130,000 March sales. . . . . . . . . . . . . . . . . $175,000 Requirement Prepare a cash collections budget for the first quarter, with a column for each month and for the quarter. (Round your answers to the nearest whole dollar.) Sweeney Corporation Cash Collections Budget For the Months of January through March January Cash sales Collections on credit sales: 20% Month of sale 40% Month after 24% Two months after Total cash collections Enter any number in the edit fields and then click Check An When the nuclide carbon-14 undergoes beta decay: The name of the product nuclide is . The symbol for the product nuclide is What is the issue with the work? It is wrong. Please answer this for points! Given the data: Ag2O(s), = 31.1 kJ mol-1, S = +121.3 J mol-1 K-1 Ag(s), = 0.00 kJ mol-1, S = +42.55 J mol-1 K-1 O2(g), = 0.00 kJ mol-1, S = +205.0 J mol-1 K-1 Calculate the temperature at which = 0 for the reaction, Ag2O(s) 2 Ag(s) + O2(g). Assume that, since the physical states do not change, and are independent of temperature between 50.0 C and 950.0 C. Name four breeds of cattle An octagonal pyramid ... how many faces are there, how many vertices and how many edges? A triangular prism ... how many faces are there, how many vertices and how many edges? a triangular pyramid ... how many faces are there, how many vertices and how many edges? A sample of 36 observations is selected from one population with a population standard deviation of 4.2. The sample mean is 101.5. A sample of 50 observations is selected from a second population with a population standard deviation of 5.0. The sample mean is 100.1. Conduct the following test of hypothesis using the 0.10 significance level.H0 : 1 = 2H1 : 1 2a.This is a_________tailed test.b. State the decision rule. (Negative values should be indicated by a minus sign. Round your answers to 2 decimal places.)The decision rule is to reject H0 if z is ___________the interval.c. Compute the value of the test statistic. (Round your answer to 2 decimal places.) Value of the test statistic d. What is your decision regarding H0?e. What is the p-value? (Round your answer to 4 decimal places.) g The electronic structure of which ONE of the following species cannot be adequately described by a single Lewis formula? (In other words, the electronic structure of which one can only be described by drawing two or more resonance structures?) A) C2H4 B) SO3 2 C) SO3 D) C3H8 E) HCN Abigail obtained 18.9 grams of calcium carbonate after performing a reaction. From her calculations, she knew she should have obtained 9.9 grams. What was her percent error? Round your answer to one place behind the decimal. Do not include the unit. A student lab group is brainstorming the design of an experiment that uses an ammeter (measures current) and different resistors to determine the effect of the resistance of a resistor upon the current in a simple circuit. Which Post-it note describes the most effective design?Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data. Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Move the ammeter to a different location in the circuit. Measure the current at this new location. Continue moving the ammeter to different locations within the circuit but be careful to keep the resistor in a fixed location. Measure and record all current values. Obtain a variety of batteries and build several circuits. Make sure that each circuit has at least one resistor and make sure that the resistance values are different in the different circuits. Place various ammeters in each circuit. Measure the number of batteries and the current for each of the circuits. Record the resistance values used in each of these circuits. Put a 10.0-ohm resistor in a circuit with a single D-cell. Measure the current in the circuit. Add a second D-cell and measure the current with two D-cells. Repeat trials for three, four, and five D-cells, being careful to get accurate current measurements for a fixed amount of resistance in each trial. I'm really confused with this plz help Question 5 of 10How did the English colonists profit from the slave trade?A. They sold the slaves to the colonies of other countries.B. They used slave labor to produce cash crops.C. They put well-trained slaves in their armies.D. They traded slaves to the natives for supplies. Reread "Our Backyard Is 85 Million Acres." Which options support the author's choice of using a proposition-and-support structure to develop his argument? A study of 25 graduates of four-year public colleges revealed the mean amount owed by a student in student loans was $55,051. The standard deviation of the sample was $7,568.Required:a. Construct a 90% confidence interval for the population mean.b. Confidence interval for the population men between _______ up to_______________ analyze how an American identity developed in New England in the 17th century what recent major breakthroughs are attributed to engineers in improving the quality of our everyday lives?