Complete question:
A charge of 15C is moving with velocity of 6.2 x 10³ m/s which makes an angle of 48 degrees with respect to the magnetic field. If the force on the particle is 4838 N, find the magnitude of the magnetic field.
a. 0.06 T
b. 0.08 T
c. 0.07 T
d. 0.05 T
Answer:
The magnitude of the magnetic field is 0.07 T.
Explanation:
Given;
magnitude of the charge, q = 15C
velocity of the charge, v = 6.2 x 10³ m/s
angle between the charge and the magnetic field, θ = 48°
the force on the particle, F = 4838 N
The magnitude of the magnetic field can be calculated by applying Lorentz force formula;
F = qvBsinθ
where;
B is the magnitude of the magnetic field
B = F / vqsinθ
B = (4838) / (6.2 x 10³ x 15 x sin48)
B = 0.07 T
Therefore, the magnitude of the magnetic field is 0.07 T.
1) True or False:
Atomic mass number is the number of neutrons and protons.
2) True or False:
Fe (iron) has 26 protons. Hint: protons equal what number?
3) True or False:
A photon of infrared light has less energy than a photon of red light.
Answer:
1.true
Explanation:
Answer:
1. True
2. True
3. True
Explanation for Question 1.
A nucleus consists of a bunch of protons and neutrons; these are known as nucleons. The atomic mass number, which is the total number of nucleons;
So, this sentence says that the atomic number is the number of protons and neutrons.
Explanation for Question 2.
Iron has 26 protons.
The number of protons = the atomic number.
So, the atomic number should be 26 also,
When we see the periodic table, Iron's atomic number is 26, so the statement is true.
Explanation for Question 3.
Red photons of light carry about 1.8 electron volts of energy. Infrared radiation has longer waves than red light, and thus oscillates at a lower frequency and carries less energy.
So, the above statement proves that the photon of infrared light has less energy than the photon of red light.
Five wheels are connected as shown in the figure. Find the velocity of the block “Q”, if it is known that: RA= 5 [m], RB= 10 [m], RD= 6 [m], RE=12 [m].
Answer:
-5 m/s
Explanation:
The linear velocity of B is equal and opposite the linear velocity of E.
vB = -vE
vB = -ωE rE
10 m/s = -ωE (12 m)
ωE = -0.833 rad/s
The angular velocity of E is the same as the angular velocity of D.
ωE = ωD
ωD = -0.833 rad/s
The linear velocity of Q is the same as the linear velocity of D.
vQ = vD
vQ = ωD rD
vQ = (-0.833 rad/s) (6 m)
vQ = -5 m/s
A screen is placed a distance dd to the right of an object. A converging lens with focal length ff is placed between the object and the screen. In terms of f, what is the smallest value d can have for an image to be in focus on the screen?
Answer:
2f
Explanation:
The formula for the object - image relationship of thin lens is given as;
1/s + 1/s' = 1/f
Where;
s is object distance from lens
s' is the image distance from the lens
f is the focal length of the lens
Total distance of the object and image from the lens is given as;
d = s + s'
We earlier said that; 1/s + 1/s' = 1/f
Making s' the subject, we have;
s' = sf/(s - f)
Since d = s + s'
Thus;
d = s + (sf/(s - f))
Expanding this, we have;
d = s²/(s - f)
The derivative of this with respect to d gives;
d(d(s))/ds = (2s/(s - f)) - s²/(s - f)²
Equating to zero, we have;
(2s/(s - f)) - s²/(s - f)² = 0
(2s/(s - f)) = s²/(s - f)²
Thus;
2s = s²/(s - f)
s² = 2s(s - f)
s² = 2s² - 2sf
2s² - s² = 2sf
s² = 2sf
s = 2f
Explain why the two plates of a capacitor are charged to the same magnitude when a battery is connected to the capacitor.
Answer:
This is because the same electron removed from the positively charged plate is what is taken to the negatively charged plate, maintaining the same amount of electron according to the conservation of charge in an electric circuit.
Explanation:
In any circuit, electrons are neither created nor destroyed according to the laws of conservation of charge, but are transferred from one point to another on the circuit. When the plates of a capacitor are connected to battery, the battery pushes the electron to move due to its potential difference. Electrons are then moved from the positive plate, at a steady rate, to the negative plate. The removal of electrons from the positive plate is what leaves it positively charged from deficiency of electrons, and the addition of electrons at the negatively charged plate is what leaves the plate negatively charge from excess of electrons. From this, we can see that the same electrons removed from the positively charged plate are taken to the negatively charged plate.
A 0.500 H inductor is connected in series with a 93 Ω resistor and an ac source. The voltage across the inductor is V = −(11.0V)sin[(500rad/s)t]. What is the voltage across the resistor at 2.09 x 10-3 s? Group of answer choices 205 V 515 V 636 V 542 V
Answer:
205 V
V[tex]_{R}[/tex] = 2.05 V
Explanation:
L = Inductance in Henries, (H) = 0.500 H
resistor is of 93 Ω so R = 93 Ω
The voltage across the inductor is
[tex]V_{L} = - IwLsin(wt)[/tex]
w = 500 rad/s
IwL = 11.0 V
Current:
I = 11.0 V / wL
= 11.0 V / 500 rad/s (0.500 H)
= 11.0 / 250
I = 0.044 A
Now
V[tex]_{R}[/tex] = IR
= (0.044 A) (93 Ω)
V[tex]_{R}[/tex] = 4.092 V
Deriving formula for voltage across the resistor
The derivative of sin is cos
V[tex]_{R}[/tex] = V[tex]_{R}[/tex] cos (wt)
Putting V[tex]_{R}[/tex] = 4.092 V and w = 500 rad/s
V[tex]_{R}[/tex] = V[tex]_{R}[/tex] cos (wt)
= (4.092 V) (cos(500 rad/s )t)
So the voltage across the resistor at 2.09 x 10-3 s is which means
t = 2.09 x 10⁻³
V[tex]_{R}[/tex] = (4.092 V) (cos (500 rads/s)(2.09 x 10⁻³s))
= (4.092 V) (cos (500 rads/s)(0.00209))
= (4.092 V) (cos(1.045))
= (4.092 V)(0.501902)
= 2.053783
V[tex]_{R}[/tex] = 2.05 V
A resistor made of Nichrome wire is used in an application where its resistance cannot change more than 1.35% from its value at 20.0°C. Over what temperature range can it be used (in °C)?
Answer:
Pls seeattached file
Explanation:
A resistor made of Ni chrome wire is used in an application where its resistance cannot be more than 1.35 % so its temperature range will be from 33.75 to -33.75 °C.
What is Resistance?Electrical resistance, or resistance to electricity, is a force that opposes the flow of current. Ohms are used to expressing resistance values.
When there is an electron difference between two terminals, electricity will flow from high to low. In opposition to that flow is resistance. As resistance rises, the current declines. On the other side, when the resistance falls, the current rises.
According to the question,
R = R₀ (1 + α ΔT)
(1 + 0.0135)R₀ = R₀(1 + α ΔT)
ΔT = (1 + 0.0135) / α
= 0.0135 / 0.0004
= 33.75 °C.
ΔT = [(1 - 0.0135) -1]/0.004
= -33.75 °C
To get more information about Resistance :
https://brainly.com/question/11431009
#SPJ5
Suppose a 58-turn coil lies in the plane of the page in a uniform magnetic field that is directed into the page. The coil originally has an area of 0.150 m2. It is stretched to have no area in 0.100 s. What is the magnitude (in V) and direction (as seen from above) of the average induced emf if the uniform magnetic field has a strength of 1.10 T? magnitude V direction ---Select--- †\
Answer:
95.7v
Explanation
Using Faraday's law of electromagnetic induction we know that rate of change in magnetic flux will induce EMF in closed loop
So it is given as
E= Ndစ/dt
E= N BA-0/ deta t
Given that
N = 58turns
B = 1.10T
A = 0.150m^²
Deta t= 0.1s
now we have
E = 58(1.10x0.150)/0.1
= 95.7v
Magnetic flux is decreasing, so the direction of the current will be to aid the decreasing flux $decrease= CLOCKWISE
Explanation:
what is the average flow rate in of gasoline to the engine of a plane flying at 700 km/h if it averages 100.0 km/l
Answer:
1.94cm³/s
Explanation:
1L = 1000cm³
Ihr = 3600s
So
Using
Average flow rate
Fr= 1L/100Km x 700Km/1hr x 1hr/3600s x 1000cm³/ 1L
= 1.94cm³/s
Take an electric field sensor and move it in a straight line, crossing the equipotential lines. Describe the relationship between the distance between the equipotential lines and the strength of the electric field.
Answer:
E = - dV / dx
Explanation:
The equipotential lines are lines or surfaces that have the same power, therefore we can move in them without carrying out work between equipotential lines, work must be carried out, therefore the electric field changes.
The electric field and the potential are related by
E = - dV / dx
therefore when the change is faster, that is, the equipotential lines are closer, the greater the electric field must be.
Light of wavelength 520 nm is incident a on a diffraction grating with a slit spacing of 2.20 μm , what is the angle from the axis for the third order maximum?
Answer:
θ = 45.15°
Explanation:
We need to use the grating equation in this question. The grating equation is given as follows:
mλ = d Sin θ
where,
m = order number = 3
λ = wavelength of light = 520 nm = 5.2 x 10⁻⁷ m
d = slit spacing = 2.2 μm = 2.2 x 10⁻⁶ m
θ = angle from the axis = ?
Therefore,
(3)(5.2 x 10⁻⁷ m) = (2.2 x 10⁻⁶ m) Sin θ
Sin θ = (3)(5.2 x 10⁻⁷ m)/(2.2 x 10⁻⁶ m)
Sin θ = 0.709
θ = Sin⁻¹(0.709)
θ = 45.15°
The same heat transfer into identical masses of different substances produces different temperature changes. Calculate the final temperature in degrees Celsius when 1.50 kcal of heat enters 1.50 kg of the following, originally at 15.0°C.(a) water
(b) concrete
(c) steel
(d) mercury
Answer:
Final temperature Water = 20.99-degree celsius
Final temperature Concrete = 24.98 degree celsius
Final temperature Steel = 50.1 degree celsius
Final temperature Mercury = 29.26 degree celsius
Explanation:
Given the mass of each substance = 1.50 kg
Ti = 15
Q = 1.5 kcal = 6276 joule
We have to use the heat capacity of each object so find the heat capacity from the table.
Heat capacity of water = 4186 J/kg degree celsius.
Heat capacity of concrete = 840 J/kg degree celsius.
Heat capacity of steel = 452 J/kg degree celsius.
Heat capacity of mercury = 139 J/kg degree celsius.
Use the below formula to find the final temperature.
[tex]T_f = T_i + \frac{Q}{mc_w} \\[/tex]
[tex]\text{Temperature in the case of water.} \\= 20 + \frac{6276}{1.5 \times 4186 } \\= 20.99 \ degree \ celsius \\\text{Temperature in the case of concrete.} \\= 20 + \frac{6276}{1.5 \times 840 } \\= 24.98 \ degree \ celsius \\\text{Temperature in the case of steel.} \\= 20 + \frac{6276}{1.5 \times 452 } \\= 29.26 \ degree \ celsius \\\text{Temperature in the case of mercury.} \\= 20 + \frac{6276}{1.5 \times 139 } \\= 50.1 \ degree \ celsius \\[/tex]
A Galilean telescope adjusted for a relaxed eye is 36.2 cm long. If the objective lens has a focal length of 39.5 cm , what is the magnification
Answer:
The magnification is [tex]m = 12[/tex]
Explanation:
From the question we are told that
The object distance is [tex]u = 36.2 \ cm[/tex]
The focal length is [tex]v = 39.5 \ cm[/tex]
From the lens equation we have that
[tex]\frac{1}{f} = \frac{1}{u} + \frac{1}{v}[/tex]
=> [tex]\frac{1}{v} = \frac{1}{f} - \frac{1}{u}[/tex]
substituting values
[tex]\frac{1}{v} = \frac{1}{39.5} - \frac{1}{36.2}[/tex]
[tex]\frac{1}{v} = -0.0023[/tex]
=> [tex]v = \frac{1}{0.0023}[/tex]
=> [tex]v =-433.3 \ cm[/tex]
The magnification is mathematically represented as
[tex]m =- \frac{v}{u}[/tex]
substituting values
[tex]m =- \frac{-433.3}{36.2}[/tex]
[tex]m = 12[/tex]
A car moving east at 45 km/h turns and travels west at 30 km/h. What is the
magnitude and direction of the change in velocity?
mahalle 1.11
Explanation:
Change in Velocity = final velocity - initial velocity
Change in velocity = 30km/h - (- 45km/h )
= 75 km/h due west
A 26-g rifle bullet traveling 220 m/s embeds itself in a 3.8-kg pendulum hanging on a 2.7-m-long string, which makes the pendulum swing upward in an arc, Determine the vertical and horizontal component of the pendulum's maximum displacement
Answer:
displacements are 0.776m, 0.114m
Explanation:
We were given mass of 26-g rifle bullet , then we can convert to Kg since
Momentum is conserved here.
The initial momentum before impact = (Mi * Vi)
Where Mi= initial given mass
Vi=initial velocity given
= 0.026 * 220 = 5.72 kgm/s
The final momentum after impact is (Mf * Vf )
Mf= final mass
5.72=( 3.82* Vf )
= 5.72/ 3.82
= 1.497 m/s
the speed of the pendulum bob with bullet afterwards= 1.497 m/s
the total energy after the collision is the addition of the kinetic energy of the bob+bullet and the potential energy of the bob and bullet, potential energy can be taken as zero.
M = 3.82 kg the mass of the bob containing the bullet
E(total) = ¹/₂MV² = 1/2 * (3.82kg)*(1.497m/s)² = 4.280J
When the Bob got to highest point the kinetic energy is zero and the potential energy is due to the increase in height of the bob, and the addition of the potential and kinetic energies still equal the total energy from before
E(total) = Mgh + 0 = Mgh = 4.280J
solving for h and substituting,
h = 4.280 J/(9.8m/s^2*3.82kg) = 0.114 m
Since the height is found,we the angle of the pendulum at the top of the swing can also be determined
A = arccos[(2.7 - 0.114) / 2.7] or A = 16.71degrees
Since A is known, the displacement along the horizontal axis can be calculated as
x = 2.7* sin(A) = 0.776m
therefore, displacement is 0.776m, 0.114m
the vertical and horizontal component of the pendulum's maximum displacement are displacement is 0.776m, 0.114m
A thin film of soap with n = 1.37 hanging in the air reflects dominantly red light with λ = 696 nm. What is the minimum thickness of the film?
Answer:
The thickness is [tex]t = 1.273 *10^{-7} \ m[/tex]
Explanation:
From the question we are told that
The refractive index of the film is [tex]n = 1.37[/tex]
The wavelength is [tex]\lambda = 696 \ nm = 696 *10^{-9 } \ m[/tex]
Generally the condition for constructive interference in a film is mathematically represented as
[tex]2 * t = [m + \frac{1}{2} ] \lambda_k[/tex]
Here t is the thickness of the film , m is the order number (0, 1, 2, 3 ... )
[tex]\lambda _k[/tex] is the wavelength of light that is inside the film , this is mathematically evaluated as
[tex]\lambda _k = \frac{ \lambda }{ n}[/tex]
[tex]\lambda _k = \frac{ 696 *10^{-9}}{ 1.37}[/tex]
[tex]\lambda _k = 5.095 *10^{-7 } \ m[/tex]
So for m = 0
[tex]t = [ 0 + \frac{1}{2} ] \lambda _k * \frac{1}{2}[/tex]
substituting values
[tex]t = [ 0 + \frac{1}{2} ] (5.095 *10^{-7}) * \frac{1}{2}[/tex]
[tex]t = 1.273 *10^{-7} \ m[/tex]
An undiscovered planet, many light-years from Earth, has one moon, which has a nearly circular periodic orbit. If the distance from the center of the moon to the surface of the planet is 2.165×105 km and the planet has a radius of 4175 km and a mass of 6.70×1022 kg , how long (in days) does it take the moon to make one revolution around the planet? The gravitational constant is 6.67×10−11N·m2/kg2 .
Answer:
364days
Explanation:
Pls see attached file
Explanation:
The moon will take 112.7 days to make one revolution around the planet.
What is Kepler's third law?The period of the satellite around any planet only depends upon the distance between the planet's center and satellite and also depends upon the planet's mass.
Given, the distance from the moon's center to the planet's surface,
h = 2.165 × 10⁵ km,
The radius of the planet, r = 4175 km
The mass of the planet = 6.70 × 10²² kg
The total distance between the moon's center to the planet's center:
a = r +h = 2.165 × 10⁵ + 4175
a = 216500 + 4175
a = 220675
a = 2.26750 × 10⁸ m
The period of the planet can be calculated as:
[tex]T =2\pi \sqrt{\frac{a^3}{Gm} }[/tex]
[tex]T =2\3\times 3.14 \sqrt{\frac{(2.20675 \times 10^8)^3}{(6.67\times 10^{-11}).(6.70\times 10^{22})} }[/tex]
T = 9738253.26 s
T = 112.7 days
Learn more about Kepler's law, here:
https://brainly.com/question/1608361
#SPJ5
An emf is induced in response to a change in magnetic field inside a loop of wire. Which of the following changes would increase the magnitude of the induced emf? A. Straighten the wire out to be flat B. Reduce the resistance of the wire of which the loop is made C. Turning the plane of the loop to be parallel to the magnetic field D. Reducing the diameter of the loop
Answer:
changing the magnetic field more rapidly
Explanation:
According to Faraday's law, whenever there is a change in the magnetic lines of force, it leads the production of induced emf. The magnitude of induced emf is proportional to to the rate of change of flux.
Hence if the magnetic field inside a loop of wire is changed rapidly, the magnitude of induced emf increases in accordance with Faraday's law of electromagnetic induction stated above when the magnetic field is changed more rapidly, hence the answer.
Specific heat is a measurement of the amount of heat energy input required for one gram of a substance to increase its temperature by one degree Celsius. Solid lithium has a specific heat of 3.5 J/g·°C. This means that one gram of lithium requires 3.5 J of heat to increase 1°C. Plot the temperature of 1g of lithium after 3.5, 7, and 10.5 J of thermal energy are added.
Answer:
ΔT = 1ºC , 2ºCand 3ºC
Explanation:
In this exercise they indicate the specific heat of lithium
let's calculate the temperature increase as a function of the heat introduced
Q = m [tex]c_{e}[/tex] ΔT
ΔT = Q / m c_{e}
calculate
for Q = 3.5 J
ΔT = 3.5 / (1 3.5)
ΔT = 1ºC
For Q = 7.0 J
ΔT = 7 / (1 3.5)
ΔT = 2ºC
for Q = 10.5 J
ΔD = 10.5 / (1 3.5)
ΔT = 3ºC
we see that this is a straight line, see attached
light of wavelength 550 nm is incident on a diffraction grating that is 1 cm wide and has 1000 slits. What is the dispersion of the m = 2 line?
Answer:
The dispersion is [tex]D = 2.01220 *10^{5} \ rad/m[/tex]
Explanation:
From the question we are told that
The wavelength of the light is [tex]\lambda = 550 \ = 550 *10^{-9} \ n[/tex]
The width of the grating is[tex]k = 1\ cm = 0.01 \ m[/tex]
The number of slit is N = 1000 slits
The order of the maxima is m = 2
Generally the spacing between the slit is mathematically represented as
[tex]d = \frac{k}{N}[/tex]
substituting values
[tex]d = \frac{ 0.01}{1000}[/tex]
[tex]d = 1.0 *10^{-5} \ m[/tex]
Generally the condition for constructive interference is
[tex]d\ sin(\theta ) = m * \lambda[/tex]
substituting values
[tex]1.0 *10^{-5} sin (\theta) = 2 * 550 *10^{-9}[/tex]
[tex]\theta = sin^{-1} [\frac{ 2 * 550 *10^{-9}}{ 1.0 *10^{-5}} ][/tex]
[tex]\theta = 6.315^o[/tex]
Generally the dispersion is mathematically represented as
[tex]D = \frac{ m }{d cos(\theta )}[/tex]
substituting values
[tex]D = \frac{ 2 }{ 1.0 *10^{-5} cos(6.315 )}[/tex]
[tex]D = 2.01220 *10^{5} \ rad/m[/tex]
An electron is trapped between two large parallel charged plates of a capacitive system. The plates are separated by a distance of 1 cm and there is vacuum in the region between the plates. The electron is initially found midway between the plates with a kinetic energy of 11.2 eV and with its velocity directed toward the negative plate. How close to the negative plate will the electron get if the potential difference between the plates is 100 V? (1 eV = 1.6 x 10-19 J)
Answer:
The electron will get at about 0.388 cm (about 4 mm) from the negative plate before stopping.
Explanation:
Recall that the Electric field is constant inside the parallel plates, and therefore the acceleration the electron feels is constant everywhere inside the parallel plates, so we can examine its motion using kinematics of a constantly accelerated particle. This constant acceleration is (based on Newton's 2nd Law:
[tex]F=m\,a\\q\,E=m\,a\\a=\frac{q\,E}{m}[/tex]
and since the electric field E in between parallel plates separated a distance d and under a potential difference [tex]\Delta V[/tex], is given by:
[tex]E=\frac{\Delta\,V}{d}[/tex]
then :
[tex]a=\frac{q\,\Delta V}{m\,d}[/tex]
We want to find when the particle reaches velocity zero via kinematics:
[tex]v=v_0-a\,t\\0=v_0-a\,t\\t=v_0/a[/tex]
We replace this time (t) in the kinematic equation for the particle displacement:
[tex]\Delta y=v_0\,(t)-\frac{1}{2} a\,t^2\\\Delta y=v_0\,(\frac{v_0}{a} )-\frac{a}{2} (\frac{v_0}{a} )^2\\\Delta y=\frac{1}{2} \frac{v_0^2}{a}[/tex]
Replacing the values with the information given, converting the distance d into meters (0.01 m), using [tex]\Delta V=100\,V[/tex], and the electron's kinetic energy:
[tex]\frac{1}{2} \,m\,v_0^2= (11.2)\,\, 1.6\,\,10^{-19}\,\,J[/tex]
we get:
[tex]\Delta\,y= \frac{1}{2} v_0^2\,\frac{m (0.01)}{q\,(100)} =11.2 (1.6\,\,10^{-19})\,\frac{0.01}{(1.6\,\,10^{-19})\,(100)}=\frac{11.2}{10000} \,meters=0.00112\,\,meters[/tex]Therefore, since the electron was initially at 0.5 cm (0.005 m) from the negative plate, the closest it gets to this plate is:
0.005 - 0.00112 m = 0.00388 m [or 0.388 cm]
An object is made of glass and has the shape of a cube 0.13 m on a side, according to an observer at rest relative to it. However, an observer moving at high speed parallel to one of the object's edges and knowing that the object's mass is 2.0 kg determines its density to be 7300 kg/m3, which is much greater than the density of glass. What is the moving observer's speed (in units of c) relative to the cube
Answer:
The velocity is [tex]v = 2.6*10^{8} \ m/s[/tex]
Explanation:
From the question we are told that
The side of the cube is [tex]l = 0.13 \ m[/tex]
The mass of the object is [tex]m = 2.0 \ kg[/tex]
The density of the object is [tex]\rho = 7300 \ kg / m^3[/tex]
Generally the volume of the object according to the moving observer is mathematically represented as
[tex]V =\frac{m}{\rho}[/tex]
[tex]V =\frac{2}{7300}[/tex]
[tex]V = 2.74*10^{-4} \ m^3[/tex]
Therefore the length of the side as observed by the observer on high speed is mathematically represented as
[tex]L = \sqrt[3]{V}[/tex]
[tex]L = \sqrt[3]{2.74 *10^{-4}}[/tex]
[tex]L =0.065[/tex]
Now the original length of side is mathematically represented as
[tex]L= l * \sqrt{ (1 - ( \frac{ v}{c})^2 )}[/tex]
Where c is the speed of light with value [tex]c = 3.0*10^{8} \ m/s[/tex]
So
[tex]v = \sqrt{1 - [\frac{L}{l}]^2} * c[/tex]
=> [tex]v = \sqrt{1 - [\frac{0.065}{0.13}]^2} * c[/tex]
=> [tex]v = 2.6*10^{8} \ m/s[/tex]
A 0.50-T magnetic field is directed perpendicular to the plane of a circular loop of radius 0.25 m. What is the magnitude of the magnetic flux through the loop
Answer:
The magnitude of the magnetic flux through the loop is 0.0982 T.m²
Explanation:
Given;
magnitude of magnetic field, B = 0.5 T
radius of the loop, r = 0.25 m
Area of the loop is given by;
A = πr²
A = 3.142 x (0.25)²
A = 0.1964 m²
The magnitude of the magnetic flux through the loop is given by;
Ф = BA
Where;
B is the magnitude of the magnetic field
A is area of the field
Ф = 0.5 x 0.1964
Ф = 0.0982 T.m²
Therefore, the magnitude of the magnetic flux through the loop is 0.0982 T.m²
Which of the following explains why a “control” is important in a case-control study of a disease? The researchers need to control the bias that those who contracted the disease may create when they talk to others. The researchers need to compare those who contracted the disease to those who did not. The researchers need to compare those who contracted the disease to those who contracted previous diseases. The researchers need to control the disease so that it is not spread further.
The researchers need to compare those who contracted the disease to those who did not.
A double-slit experiment is performed with light of wavelength 620 nm. The bright interference fringes are spaced 2.3 mm apart on the viewing screen. What will the fringe spacing be if the light is changed to a wavelength of 360 nm?
Answer:
1.34 mm
Explanation:
A double slit experiment is conducted with a light which has a wavelength of 620 nm
The fringes are separated 2.3 mm apart
The light is changed to a wavelength length of 360 nm
Let x represent the fringe spacing as a result of the change in wavelength
Therefore,the fringe spacing can be calculated as follows
2.3mm/x= 620nm/360nm
Multiply both sides
x × 620= 2.3×360
620x= 828
x= 828/620
x= 1.34 mm
Which best identifies the requirements for work to be performed? an object that has a force acting on it an object that is moving and has no net force a force acting on a motionless object a force that moves an object
Answer:
a force that moves an object
Explanation:
the formula for work is force * distance
This question involves the concepts of work, force, and displacement.
The statement that best identifies the requirements for work to be performed is "a force that moves an object".
Work is defined as the product of force applied on an object and the distance moved by the object. Mathematically,
Work = (Force)(Displacement)
Hence, both the applied force and the displacement of the object as a result of the application of the force is necessary for the work to be done. If any one of these values becomes zero, the work automatically becomes zero, which means no work is performed.
Learn more about work here:
https://brainly.com/question/4095205
At what speed (in m/s) will a proton move in a circular path of the same radius as an electron that travels at 7.45 ✕ 106 m/s perpendicular to the Earth's magnetic field at an altitude where the field strength is 1.10 ✕ 10−5 T
Answer:
The speed of the proton is 4059.39 m/s
Explanation:
The centripetal force on the particle is given by;
[tex]F = \frac{mv^2}{r}[/tex]
The magnetic force on the particle is given by;
[tex]F = qvB[/tex]
The centripetal force on the particle must equal the magnetic force on the particle, for the particle to remain in the circular path.
[tex]\frac{mv^2}{r} = qvB\\\\r = \frac{mv^2}{qvB} \\\\r = \frac{mv}{qB}[/tex]
where;
r is the radius of the circular path moved by both electron and proton;
⇒For electron;
[tex]r = \frac{(9.1*10^{-31})(7.45*10^6)}{(1.602*10^{-19})(1.1*10^{-5})}\\\\r = 3.847 \ m[/tex]
⇒For proton
The speed of the proton is given by;
[tex]r = \frac{mv}{qB}\\\\mv = qBr\\\\v = \frac{qBr}{m} \\\\v = \frac{(1.602*10^{-19})(1.1*10^{-5})(3.847)}{1.67*10^{-27}} \\\\v = 4059.39 \ m/s[/tex]
Therefore, the speed of the proton is 4059.39 m/s
The metal wire in an incandescent lightbulb glows when the light is switched on and stops glowing when it is switched off. This simple
process is which kind of a change?
OA a physical change
OB. a chemical change
OC. a nuclear change
OD
an ionic change
B. A chemical change
Explanation:
I'm guessing ?
The bar magnet is pushed toward the center of a wire loop. Looking down from the top view (would appear the magnet is coming up toward the observer); Which is true? A. There is no induced current in the loop B. There is a counterclockwise induced current in the loop C. There is not enough information to correctly answer the question D. There is a clockwisee induced current in the loop
Answer:
Explanation:
B. There is a counterclockwise induced current in the loop
Explanation:
This in line with the right hand grip rule,
The right hand rule states that: to determine the direction of the magnetic force on a positive moving charge, ƒ, point the thumb of the right hand in the direction of v, the fingers in the direction of B, and a perpendicular to the palm points in the direction of F.
The near point (the smallest distance at which an object can be seen clearly) and the far point (the largest distance at which an object can be seen clearly) are measured for six different people.
Near Point(cm) Far Point(cm)
Avishka 40 [infinity]
Berenice 30 300
Chadwick 25 500
Danya 25 [infinity]
Edouard 80 200
Francesca 50 [infinity]
Of the farsighted people, rank them by the power of the lens needed to correct their hyperopic vision. Rank these from largest to smallest power required.
1. Berenice
2. Avishka
3. Francesca
4. Edouard
Answer:
1. Berenice = 0.67 D
2. Avishka = 1.50 D
3. Francesca = 2.00 D
4. Edouard = 2.75 D
Explanation:
The farsighted people are those with near point greater than 25 cm.
They include Avishka, Berenice, Edouard and Francisca.
A converging lens is needed to correct farsightedness, or hyperopia, therefore, the focal length, f, is positive. The image formed is virtual and on the same side of the lens. Thus the image distance is negative
From the lens formula, 1/f = 1/v 1/u; but v is negative
Therefore, 1/f = 1/u - 1/v
But, power of a lens = 1/f in meters.
Therefore, P = 1/u - 1/v
For Avishka, u = 25 cm or 0.25 m, v = 0.4 m
P = 1/ 0.25 - 1/0.4 = 1.5 D
For Berenice, u = 0.25 m, v = 0.3 m
P = 1/0.25 - 1/0.30 =0.7 D
For Edouard, u = 0.25 m, v = 0.80 m
P = 1/0.25 - 1/0.80 =2.75 D
For Francesca, u = 0.25 m, v = 0.50 m
P = 1/0.25 - 1/0.5 = 2.0 D
When The farsighted people are those with a near point greater than 25cm.
Berenice is = 0.67 D
Avishka is = 1.50 D
Francesca is = 2.00 D
Edouard is = 2.75 D
What is Hyperopic Vision?
When The farsighted people are those with a near point greater than 25 cm. Then, They include Avishka, Berenice, Edouard, and also Francisca.
Also, A converging lens is needed to correct farsightedness, or hyperopia, thus, When the focal length, f, is positive. Also, The image formed is virtual and also on the same side of the lens. hence the image distance is negative.
Also, From the lens formula, 1/f = 1/v 1/u; but v is negative
Thus, 1/f = 1/u - 1/v
But, when the power of a lens = 1/f in meters.
Thus, P = 1/u - 1/v
For Avishka, u = 25 cm or 0.25 m, v = 0.4 m
After that, P = 1/ 0.25 - 1/0.4 = 1.5 D
Then, For Berenice, u = 0.25 m, v = 0.3 m
Now, P = 1/0.25 - 1/0.30 =0.7 D
For Edouard, u = 0.25 m, v is = 0.80 m
Then, P = 1/0.25 - 1/0.80 is =2.75 D
Now, For Francesca, u = 0.25 m, v is = 0.50 m
Therefore, P = 1/0.25 - 1/0.5 = 2.0 D
Find more information about Hyperopic Vision here:
https://brainly.com/question/25676535
A charming friend of yours who has been reading a little bit about astronomy accompanies you to the campus observatory and asks to see the kind of star that our Sun will ultimately become, long, long after it has turned into a white dwarf. Why is the astronomer on duty going to have a bit of a problem satisfying her request? a. All the old stars in our Galaxy are located in globular clusters and all of these are too far away to be seen with the kind of telescope a college or university campus would have. b. After being a white dwarf, the Sun will explode, and there will be nothing left to see. c. The universe is not even old enough to have produced any white dwarfs yet d. Astronomers only let people with PhD's look at these stellar corpses; it's like an initiation rite for those who become astronomers. e. After a white dwarf cools off it becomes too cold and dark to emit visible light
Answer:
b
Explanation:
