A barge is hauled along a straight-line section of canal by two horses harnessed to tow ropes and walking along the tow paths on
either side of the canal. Each horse pulls with a force of 839 N at an angle of 15° with the centerline of the canal. Find the sum of these
two forces on the barge.
answer in ___kN

Answer:

100Hz

Explanation:

In a full wave rectifier, the fundamental frequency of the ripple is twice that of input frequency. Given the input frequency of 50 Hz, the fundamental frequency will be 2 × 50 = 100Hz

Answer:

HZ 100 is the right answer hope you like it

Answer:

enchantment table language

Explanation:

Answer:  

t = 1.27 x 10⁹ s  

Explanation:  

First, we will find the volume of the wire:

Volume = V = AL  

where,  

A = Cross-sectional area of wire = πr² = π(1 cm)² = π(0.01 m)² = 3.14 x 10⁻⁴ m²  

L = Length of wire = 150 km = 150000 m  

Therefore,    

V = 47.12 m³

Now, we will find the number of electrons in the wire:  

No. of electrons = n = (Electrons per unit Volume)(V)  

n = (8.43 x 10²⁸ electrons/m³)(47.12 m³)  

n = 3.97 x 10³⁰ electrons  

Now, we will use the formula of current to find out the time taken by each electron to cross the wire:

[tex]I =\frac{q}{t}[/tex]  

where,  

t = time = ?  

I = current = 500 A  

q = total charge = (n)(chareg on one electron)  

q = (3.97 x 10³⁰ electrons)(1.6 x 10⁻¹⁹ C/electron)  

q = 6.36 x 10¹¹ C  

[tex]500\ A = \frac{6.36\ x\ 10^{11}\ C}{t}\\\\t = \frac{6.36\ x\ 10^{11}\ C}{500\ A}[/tex]

Therefore,

t = 1.27 x 10⁹ s

The least distance up to which we can see the objects clearly without any strain is called least distance of distinct vision. Least distance of distinct vision for a normal human being is 25cm. For young people, the least distance of distant vision will be within 25cm which however it varies with age.

Answer:

25 you said ? thats incorecct

Explanation:

Answer:

The correct answer would be - Low pitch.

Explanation:

As it is known that if frequency increases then pitch will be increase as well as pitch depends on frequency, Now for the question it is mentioned that the tube closed on one end frequency is:

f = v/2l

Where,

l = length of the tube

v = velocity of longitudinal wave of gas filled in the tube

Now increase with the temperature the density of the gas decreases and velocity v is inversely proportional to density of gas so velocity increases. So if there is an increase in frequency so pitch also increases. As the temperature inside the house is at 750 F more than outsideat 450 Fso pitch is more inside and the pitch is low outside.

Answer:

0.28 J

Explanation:

Let the mass of the object is 0.5 kg

The maximum velocity of the object is 1.06 m/s.

We need to find the kinetic energy at that time. It is given by :

[tex]K=\dfrac{1}{2}mv^2\\\\=\dfrac{1}{2}\times 0.5\times (1.06)^2\\\\K=0.28\ J[/tex]

So, the required kinetic energy is equal to 0.28 J.

Answer:

10.01 cm

Explanation:

Given that,

The time delay between transmission and the arrival of the reflected wave of a signal using ultrasound traveling through a piece of fat tissue was 0.13 ms.

The average propagation speed for sound in body tissue is 1540 m/s.

We need to find the depth when the reflection occur. We know that, the distance is double when transmitting and arriving. So,

[tex]v=\dfrac{2d}{t}\\\\d=\dfrac{vt}{2}\\\\d=\dfrac{1540\times 0.13\times 10^{-3}}{2}\\\\d= $$0.1001\ m[/tex]

or

d = 10.01 cm

So, the reflection will occur at 10.01 cm.

Answer:

B has greater potential

Explanation:

We know;

Potential Energy (PE) = mgh

where, m=mass of body

g=acceleration due to gravity

h=height of body

From the formula,

PE is directly proportional to the mass of the body

so the body with greater mass has greater potential.

Answer:

The electric potential energy is 6.72 x 10^-11 J.

Explanation:

Potential difference, V = 4.2 x 10^8 V

charge of electron, q = - 1.6 x 10^-19 C

Let the potential energy is U.

U = q V

U = 1.6 x 10^-19 x 4.2 x 10^8

U = 6.72 x 10^-11 J

Answer:

Renewable energy is a type of energy that can be renewed easily, such as sunlight. By using Solar panels to collect the suns energy, we are not depleting it, so this source is renewable.

Non-renewable  energy is something that cannot easily be replenished. An example would be oil because oil takes millions of years to form and cannot be renewed easily.

Answer:

v₂ = 15.24 m / s

Explanation:

This is an exercise in fluid mechanics

Let's write Bernoulli's equation, where the subscript 1 is for the factory pipe and the subscript 2 is for the tank.

          P₁ + ½ ρ v₁² + ρ g y₁ = P₂ + ½ ρ v₂² + ρ g y₂

They indicate the pressure in the factory P₁ = 140000 Pa, the velocity

v₁ = 5.5 m / s and the initial height is zero y₁ = 0

the tank is at a pressure of P2 = 2000 Pa and a height of y₂ = 6.0 m

          P₁ -P₂ + ρ g (y₁ -y₂) + ½ ρ v₁² = ½ ρ v₂²

let's calculate

         140,000 - 2000 + ρ 9.8 (0- 6) + ½ ρ 5.5² = ½ ρ v₂²

         138000 - ρ 58.8 + ρ 15.125 = ½ ρ v2²

         v₂² = 2 (138000 /ρ - 58.8 + 15.125)

         v₂ = [tex]\sqrt{\frac{276000}{\rho } - 43.675 }[/tex]

In the exercise they do not indicate what type of liquid is being used, suppose it is water with

           ρ = 1000 kg / m³

           v₂ = [tex]\sqrt{\frac{276000}{1000} - 43.675}[/tex]

           v₂ = 15.24 m / s

Answer:

7.28×10⁻⁵ T

Explanation:

Applying,

F = BILsin∅............. Equation 1

Where F = magnetic force, B = earth's magnetic field, I = current flowing through the wire, L = Length of the wire, ∅ = angle between the field and the wire.

make B the subject of the equation

B = F/ILsin∅.................. Equation 2

From the question,

Given: F = 0.16 N, I = 68 A, L = 34 m, ∅ = 72°

Substitute these values into equation 2

B = 0.16/(68×34×sin72°)

B = 0.16/(68×34×0.95)

B = 0.16/2196.4

B = 7.28×10⁻⁵ T

Answer:

[tex]\omega=109.67\ rad/s[/tex]

Explanation:

Given that,

The speed of the ball, u = 34 m/s

The ball is 0.310 m from the elbow joint.

We need to find the angular velocity (in rad/s) of the forearm.

We know that,

[tex]v=r\omega\\\\\omega=\dfrac{v}{r}\\\\\omega=\dfrac{34}{0.31}\\\\\omega=109.67\ rad/s[/tex]

So, the required angular velocity of the forearm is 109.67 rad/s.

Answer:no

Explanation:because 0.9*(30*60)=0.9*1800=1620

The turtle has already won the race

Yes rabbit will win the race will distance in 3.2 hours and turtle will cover in 27 hours

It is given

[tex]V_{t} = 0.9 \frac{m}{s}[/tex]

[tex]V_{r} = 9 \frac{m}{s}[/tex]

[tex]D=1500 m[/tex]

Time taken by turtle  

 [tex]T= \dfrac{D}{V_{t} }=\dfrac{1500}{0.9_{} }[/tex]

[tex]T=1666 minutes= 27 hours[/tex]

Time taken by  rabbit

[tex]T= \dfrac{D}{V_{r} }=\dfrac{1500}{9_{} }[/tex]

[tex]T=166 minutes[/tex]

since rabbit started 30 minutes after turtle then

[tex]T= 136+30=196 minutes[/tex]

[tex]T= 3.2 hours[/tex]

Hence Yes rabbit will win the race will distance in 3.2 hours and turtle will cover in 27 hours

To know more about average velocity follow

https://brainly.com/question/6504879

Answer:

The elastic extensibility of a piece of string is .08. If the string is 100 cm long, how long will the string be when it is stretched to the point where it becomes plastic? is your ansewer dont take tension

The string will be 108 cm long when it is stretched to the point where it becomes plastic.

Elasticity in physics and materials science refers to a body's capacity to withstand a force that causes distortion and to recover its original dimensions once the force has been withdrawn.

When sufficient loads are applied, solid objects will deform; if the material is elastic, the object will return to its original size and shape after the weights have been removed. Unlike plasticity, which prevents this from happening and causes the item to stay deformed,

Given parameters:

The elastic extensibility of a piece of string is 0.08.

The string is 100 cm long.

Hence,  it becomes plastic, after  it is stretched up to = 100 × 0.08 cm = 8 cm.  The string will be 108 cm long.

Learn more about elasticity here:

https://brainly.com/question/28790459

#SPJ5

At STP, 1 mole of an ideal gas occupies a volume of about 22.4 L. So if n is the number of moles of this gas, then

n / (19.2 L) = (1 mole) / (22.4 L)   ==>   n = (19.2 L•mole) / (22.4 L) ≈ 0.857 mol

If the sample has a mass of 12.0 g, then its molecular weight is

(12.0 g) / n ≈ 14.0 g/mol

Check attached photo

Check attached photo

Answer:

Explanation:

1. If C = A + B then the lines A and B may have the same magnitude or they may not. The direction of A for example may be northwest ↖️ and the direction of B must be south ⬇️ because the arrow of A and the point of B must connect. Then C’s direction is west ⬅️ because it shouldn’t be as equilibrium.

2. If C = 0 t means the force is at equilibrium. That means all forces add up to zero. A’s direction for example may be northeast ↗️ and the direction of B may be south ⬇️ and the direction of C must be west if it has to be at equilibrium.

The magnitude of A and B must be equal

Answer:

0.5849Weber

Explanation:

The formula for calculating the magnetic flus is expressed as:

[tex]\phi = BAcos \theta[/tex]

Given

The magnitude of the magnetic field B = 3.35T

Area of the loop = πr² = 3.14(0.24)² = 0.180864m²

angle of the wire loop θ = 15.1°

Substitute the given values into the formula:

[tex]\phi = 3.35(0.180864)cos15.1^0\\\phi =0.6058944cos15.1^0\\\phi =0.6058944(0.9655)\\\phi = 0.5849Wb[/tex]

Hence the magnetic flux Φ through the loop is 0.5849Weber

Answer:

1) Law of Universal Gravitation     Gravity is an attractive force

5) General relativity               Gravity is due to the curvature of spacetime

Explanation:

In this exercise you are asked to relate the correct theory and its explanation

Theory Explanation

1) Law of Universal Gravitation              Gravity is an attractive force

2) Law of universal gravitation              Mass and distance affect force

3) Classical mechanics                           time and space are absolute

4) Special relativity                                 Time and space are relative

5) General relativity                                Gravity is due to the curvature of

                                                               spacetime

6) General relativity                                 Mass affects the curvature of space - time

Answer:

Explanation:

edge2022

Answer:

no, all substances doesnot conduct heat

Answer:

No, all substances do not conduct heat easily because it depends on the nature of the substance. Some are good conductors of heat and some are bad. Therefore, it depends on their characteristics and their ability to conduct heat.

The bad conductors of heat are water, air, plastic, wood, etc.

Gold, Silver, Copper, Aluminium, Iron, etc. are good heat conductors as well as electrical conductors.

Answer:

b. approaches zero.

Explanation:

The phenomenon is known as length contraction.

Length contraction is a result of Einstein's special theory of relativity. This theory states that an observer in an inertial frame of reference will observe a decrease in the length of any moving object placed at another inertial frame of reference.

let the length of the train = L

Let the length observed when the train is in motion = L₀

Apply Einstein's special theory of relativity;

[tex]L_0 = L \times \sqrt{1 - \frac{v^2}{c^2} } \\\\where;\\\\v \ is \ the \ velocity \ of \ the \ train\\\\c \ is \ the \ speed \ of \ light\\\\[/tex]

from the equation above, when v = 0, the length observed is equal to the initial length of the train. (L₀ = L)

As the velocity of the train (v) approaches the speed of light (c), the length of the train observed (L₀) becomes smaller than the initial length of the train (L).  (L₀ < L)

Eventually, when v equals c, we will have a square root of zero (0), and the length observed will become zero.  (L₀ = 0)

Thus, the length of this object, as measured by a stationary observer approaches zero

Answer:

The required fraction is 0.023.

Explanation:

Given that

Mass of a car, m = 1030 kg

Mass of 4 wheels = 12 kg

We need to find the fraction of the total kinetic energy of the car is due to rotation of the wheels about their axles.

The rotational kinetic energy due to four wheel is

[tex]=4\times \dfrac{1}{2}I\omega^2\\\\=4\times \dfrac{1}{2}\times \dfrac{1}{2}mR^2(\dfrac{v}{R})^2\\\\=mv^2[/tex]

Linear kinetic Energy of the car is:

[tex]=\dfrac{1}{2}mv^2\\\\=\dfrac{1}{2}\times Mv^2[/tex]

Fraction,

[tex]f=\dfrac{mv^2}{\dfrac{1}{2}Mv^2}\\\\f=\dfrac{m}{\dfrac{1}{2}M}\\\\f=\dfrac{12}{\dfrac{1}{2}\times 1030}\\\\=0.023[/tex]

So, the required fraction is 0.023.

Answer:

Option D. ²²²₉₀Th

Explanation:

Let the unknown be ⁿₘZ. Thus, the equation becomes:

²²⁶₉₂U —> ⁴₂He + ⁿₘZ

Next, we shall determine n, m and Z. This can be obtained as follow:

For n:

226 = 4 + n

Collect like terms

226 – 4 = n

222 = n

n = 222

For m:

92 = 2 + m

Collect like terms

92 – 2 = m

90 = m

m = 90

For Z:

ⁿₘZ => ²²²₉₀Z => ²²²₉₀Th

Therefore, the complete equation becomes:

²²⁶₉₂U —> ⁴₂He + ⁿₘZ

²²⁶₉₂U —> ⁴₂He + ²²²₉₀Th

Thus, the unknown is ²²²₉₀Th

Answer:

 I = - m 16  the two impulses are the same,

Explanation:

The impulse is given by the relationship

         I = Δp

         I = p_f - p₀

in this case the final velocity is zero therefore p_f = 0

        I = -p₀

For driver A the steering wheel impulse is

        I = - m v₀

        I = - m 16

For driver B, the airbag gives an impulse

        I = - m 16

We can see that the two impulses are the same, the difference is that in the air bag more time is used to give this impulse therefore the force on the driver is less

Answer:

So the correct answer is letter e)

Explanation:

The electric field of an infinite yz-plane with a uniform surface charge density  (σ) is given by:

[tex]E=\frac{\sigma }{2\epsilon_{0}}[/tex]

Where ε₀ is the electric permitivity.

As we see, this electric field does not depend on distance, so the correct answer is letter e)

I hope it helps you!

Answer:

a) required area is 1.1318 m²

b) the maximum potential difference that can be applied across the compactor is 1931.1 V

Explanation:

Given the data in the question;

dielectric constant εr = 2.35

distance between plates ( thickness ) d = 0.0785 mm = 7.85 × 10⁻⁵ m

dielectric strength = 49.5 MV/m

a)

given that capacity capacitor C = 0.3 uF = 0.3 × 10⁻⁶ F

To find the Area, we use the following the expression.

C = ε₀εrA / d

we know that The permittivity of free space, ε₀ = 8.854 x 10⁻¹²  (F/m)

we substitute

0.3 × 10⁻⁶ = [ (8.854 x 10⁻¹²) × 2.35 × A  ] /  7.85 × 10⁻⁵

A = [ (0.3 × 10⁻⁶) × (7.85 × 10⁻⁵) ] / [ 2.35 × (8.854 x 10⁻¹²) ]

A = 2.355 × 10⁻¹¹ / 2.08069 × 10⁻¹¹

A = 1.1318 m²

Therefore, required area is 1.1318 m²

b)

the maximum potential difference that can be applied across the compactor.

We use the following expression;

⇒ 1/2 × dielectric strength × thickness d

we substitute

⇒ 1/2 × ( 49.5 × 10⁶ V/m ) × ( 7.85 × 10⁻⁵ m )

⇒ 1931.1 V

Therefore, the maximum potential difference that can be applied across the compactor is 1931.1 V

Answer: [tex]283.2\times 10^{-9}\ nC[/tex]

Explanation:

Given

Cross-sectional area [tex]A=0.4\ cm^2[/tex]

Dielectric constant [tex]k=4[/tex]

Dielectric strength [tex]E=2\times 10^8\ V/m[/tex]

Distance between capacitors [tex]d=5\ mm[/tex]

Maximum charge that can be stored before dielectric breakdown is given by

[tex]\Rightarrow Q=CV\\\\\Rightarrow Q=\dfrac{k\epsilon_oA}{d}\cdot (Ed)\quad\quad [V=E\cdot d]\\\\\Rightarrow Q=k\epsilon_oAE\\\\\Rightarrow Q=4\times 8.85\times 10^{-12}\times 0.4\times 10^{-4}\times 2\times 10^8\\\\\Rightarrow Q=28.32\times 10^{-8}\\\\\Rightarrow Q=283.2\times 10^{-9}\ nC[/tex]

Answer:

The maximum charge is 7.08 x 10^-8 C.

Explanation:

Area, A = 0.4 cm^2

K = 4

Electric field, E = 2 x 10^8 V/m

separation, d = 5 mm = 0.005 m

Let the capacitance is C and the charge is q.

[tex]q = CV\\\\q=\frac{\varepsilon o A}{d}\times E d\\\\q = \varepsilon o A E\\\\q = 8.85\times 10^{-12}\times0.4\times 10^{-4}\times 2\times 10^8\\\\q = 7.08\times 10^{-8}C[/tex]

Answer:

0

Explanation:

The speed of the ball when it reaches the floor is 0 because when an object is at rest or in uniform motion, it has no speed/velocity

The final speed of the ball when it reaches the floor is 7.10 m/s.

The conservation of energy is a fundamental principle in physics that states that energy cannot be created or destroyed, but only converted from one form to another or transferred from one system to another. In other words, the total amount of energy in a closed system remains constant over time, even though it may be converted from one form to another.

This principle is based on the first law of thermodynamics, which states that the total energy of a closed system is always conserved, and can only be changed by the transfer of heat, work, or matter into or out of the system. The conservation of energy has important applications in various fields of physics, including mechanics, thermodynamics, and electromagnetism, and is a fundamental principle in the understanding of the natural world.

Here in the Question,

We can use the conservation of energy to solve this problem. Initially, the ball has kinetic energy due to its motion on the tabletop, but no potential energy since it is at a constant height. When the ball rolls off the edge of the table, it loses some kinetic energy due to friction but gains potential energy as it moves upward. When it reaches the floor, it has gained potential energy but lost kinetic energy due to friction. We can assume that the energy lost due to friction is converted to thermal energy, so the total energy of the system is conserved.

Let's start by calculating the potential energy gained by the ball as it moves from the edge of the table to the floor:

ΔPE = mgh

where ΔPE is the change in potential energy, m is the mass of the ball, g is the acceleration due to gravity, and h is the vertical distance traveled by the ball.

ΔPE = (0.50 kg)(9.81 m/s^2)(1.0 m) = 4.905 J

Now we can use the conservation of energy to find the final kinetic energy of the ball, which will allow us to calculate its final speed:

KEi + ΔPEi = KEf + ΔPEf

where KEi and ΔPEi are the initial kinetic and potential energies of the ball, respectively, and KEf and ΔPEf are the final kinetic and potential energies of the ball, respectively.

Since the ball is not bouncing, we can assume that its initial and final potential energies are zero. Therefore:

KEi = KEf + ΔKE

where ΔKE is the change in kinetic energy due to friction.

We can assume that the coefficient of kinetic friction between the ball and the incline is constant, and use the work-energy principle to find ΔKE:

Wfric = ΔKE

where Wfric is the work done by friction.

The work done by friction can be expressed as:

Wfric = ffricd

where ffric is the force of friction and d is the distance traveled by the ball on the incline.

The force of friction can be expressed as:

ffric = μmg

where μ is the coefficient of kinetic friction, and m and g have their usual meanings.

Putting it all together, we get:

KEi = KEf + ffricd

KEi = KEf + μmgd

(1/2)mv^2 = (1/2)mu^2 + μmgd

v^2 = u^2 + 2gd

where u is the initial speed of the ball on the tabletop, and v is the final speed of the ball on the floor.

Plugging in the given values, we get:

v^2 = (5.0 m/s)^2 + 2(9.81 m/s^2)(1.0 m)

v^2 = 50.405

v = 7.10 m/s

Therefore, the final speed of the ball when it reaches the floor is 7.10 m/s.

To learn more about  the Law of Conservation of Momentum click:

https://brainly.com/question/30487676

#SPJ2

Answer:

28 j

Explanation:

because when you add you get 28