The banana will slide a distance of 20.75 m on the pavement before coming to a stop.
we have
v² = u² + 2ghv² = 0.5² + 2 × 9.8 × 5v²
= 0.25 + 98v² = 98.25v
= √98.25v
≈ 9.91 m/s
When the banana reaches the pavement, the force of friction is responsible for the stopping of the banana.
The frictional force, f = μR
Here, R is the reaction force that acts perpendicular to the surface. So, R = mg, where m is the mass of the banana and g is the acceleration due to gravity. f = μmg
Also, the force that is responsible for stopping the banana is the frictional force, f.
So, f = ma
Here, a is the acceleration of the banana just after it leaves the ramp and starts moving on the pavement.
So, we can write,
μmg = ma
μg = a
At the instant when the banana leaves the ramp and starts moving on the pavement, its velocity is 9.91 m/s.
Therefore, using the equations of motion,
v² = u² + 2as0 = 9.91² + 2a × ss = (0 - 98.2)/2 × (-0.23)s = 20.75 m
The banana will slide a distance of 20.75 m on the pavement before coming to a stop.
learn more about friction here
https://brainly.com/question/24338873
#SPJ11
If you are driving an oscillatory system at a certain frequency, but the amplitude is much smaller than it could be, you can be certain that If you are driving an oscillatory system at a certain frequency, but the amplitude is much smaller than it could be, you can be certain that The driving frequency is too low. The driving frequency is too high. The driving frequency is not matched to the natural frequency of the oscillatory system.
If you are driving an oscillatory system at a certain frequency, but the amplitude is much smaller than it could be, you can be certain that the driving frequency is not matched to the natural frequency of the oscillatory system.
When an oscillatory system is driven at its natural frequency, it undergoes resonance, resulting in maximum amplitude. However, if the driving frequency is not matched to the natural frequency, the system will not respond with a large amplitude. Instead, the amplitude will be smaller.
In such a case, the oscillatory system is not efficiently absorbing energy from the driving force, and the motion becomes less pronounced. This indicates that the driving frequency does not coincide with the natural frequency of the system, leading to a suboptimal response and a smaller amplitude.
To know more about oscillatory system, click here https://brainly.com/question/28256327
#SPJ11
If he wants the four ring magnets to be attracted to each other, which magnet A, B, C or D should he flip?
Explain your answer
To make the four ring magnets attract each other, he should flip magnet D.
The behavior of magnets is governed by their poles: north (N) and south (S). Like poles repel each other (N-N or S-S), while opposite poles attract each other (N-S).
Looking at the configuration of the magnets, we can determine which one needs to be flipped to achieve attraction. If magnet D is flipped, its north pole (N) will face the south pole (S) of magnet C. Since opposite poles attract, this will create an attractive force between the two magnets.
If magnet A, B, or C is flipped, it will result in like poles facing each other, leading to repulsion rather than attraction.
Therefore, to ensure that the four ring magnets attract each other, magnet D should be flipped so that its north pole (N) faces the south pole (S) of magnet C, allowing for an attractive force between them.
To learn more about ring magnets, here
https://brainly.com/question/28716518
#SPJ4
A car is moving at 44 m/s. On wet concrete, a car decelerate at a rate of 7.31 m/s2. Finding the displacement from the point where the driver sees a traffic light turn red, taking into account his reaction time of 0.56 s to get his foot on the brake
The displacement of the car from the point where the driver sees the traffic light turn red, considering the reaction time, is 23.66 meters.
To calculate the displacement, we need to consider the time it takes for the driver to react and apply the brakes. During this time, the car continues to move at its initial velocity. The formula to calculate displacement is given by:
displacement = initial velocity × time + (1/2) × acceleration × time²
First, we calculate the displacement during the reaction time:
displacement_reaction = initial velocity × reaction time
Next, we calculate the displacement while decelerating:
displacement_deceleration = (1/2) × acceleration × (total time - reaction time)²
Finally, we sum up the two displacements to get the total displacement:
total displacement = displacement_reaction + displacement_deceleration
Plugging in the values, we have:
displacement_reaction = 44 m/s × 0.56 s = 24.64 m
displacement_deceleration = (1/2) × (-7.31 m/s²) × (total time - 0.56 s)²
(total time - 0.56 s) is the time spent decelerating.
Combining the two displacements, we find the total displacement to be approximately 23.66 meters.
Learn more about displacement here:
brainly.com/question/11934397
#SPJ11.
Compare the magnitude of the electromagnetic and gravitational force between two electrons separated by a distance of 2. 00 m. Assume the electrons have a mass of 9. 11 × 10–31 kg and a charge of 1. 61 × 10–19 C. Round to two decimal places. Fe = × 10–29 N Fg = × 10–71 N F Subscript e baseline over F Subscript g baseline. = × 1042.
Fₑ/Fg is 9.63 × 10⁻²². To compare the magnitude of the electromagnetic and gravitational force between two electrons separated by a distance of 2.00 m we can use the Coulomb's law and Newton's law of gravitation formula. The formula for the electric force between two charges is given as: F = kq₁q₂ / r²
Where, k = Coulomb constant = 9 × 10⁹ Nm²C⁻², q₁ and q₂ = charges on the two particles, r = distance between the two particles
For two electrons, q₁ = q₂ = -1.61 × 10⁻¹⁹ , CR = 2.00 m
F = 9 × 10⁹ × (-1.61 × 10⁻¹⁹)² / (2.00)²
= 2.31 × 10⁻²⁸ N
The formula for gravitational force between two particles is given as: F = Gm₁m₂ / r²: where, G = gravitational constant = 6.67 × 10⁻¹¹ Nm²/kg², m₁ and m₂ = masses of the two particles, r = distance between the two particles
For two electrons, m₁ = m₂ = 9.11 × 10⁻³¹ kg, R = 2.00 m
Substituting the values in the formula we get, F = 6.67 × 10⁻¹¹ × (9.11 × 10⁻³¹)² / (2.00)²
= 2.40 × 10⁻⁷ N
Thus, the magnitude of the electromagnetic force is 2.31 × 10⁻²⁸ N and the magnitude of the gravitational force is 2.40 × 10⁻⁷ N.
The ratio of Fe/Fg= (2.31 × 10⁻²⁸)/(2.40 × 10⁻⁷)
= 9.63 × 10⁻²²
Thus, Fₑ/Fg is 9.63 × 10⁻²².
To know more about electric force, refer
https://brainly.com/question/30236242
#SPJ11
Answer:
see picture
Explanation:
What heat energy transfer process is responsible for transferring heat energy from the earth to the air directly above it?.
The heat energy transfer process responsible for transferring heat energy from the Earth to the air directly above it is conduction.
What is Conduction?Conduction is a form of heat transfer in which heat moves from one object to another by direct contact without the requirement of any physical motion of the objects themselves.
Conduction occurs when a heat source, such as the Earth's surface, transfers heat energy to the air molecules in contact with it. The air molecules, which are heated by conduction, then move and collide with other air molecules in the surrounding area, eventually spreading the heat throughout the atmosphere.
Convection is another type of heat transfer that plays a significant role in the transfer of heat from the Earth's surface to the atmosphere. This occurs as air that is heated by conduction rises, creating convection currents that move heat throughout the atmosphere as air circulates in the environment.
learn more about Conduction here
https://brainly.com/question/20493362
#SPJ11
After scientists have a number of ideas about robot movement in mind, what types of tests do they then perform?
After scientists have a number of ideas about robot movement in mind, they then perform various types of tests to validate their theories and see how the robot actually moves in the real world. Robotics engineers design, build, and program robots, and their work focuses on a few key areas such as mechanics, control theory, electronics, and computer programming. Robotics engineers work in a variety of fields and industries, including manufacturing, aerospace, and healthcare. Before a robot is sent to the market, it must go through rigorous testing to ensure that it functions as intended and meets the safety standards set by regulatory bodies.
To test the robot movement, engineers use computer simulations and physical prototypes. Computer simulations allow engineers to test robot behavior and movement in a virtual environment, while physical prototypes are used to test the robot's movement in the real world. Once the robot has been built, the engineers will test it to see if it moves as intended.
They may also conduct tests to see how the robot performs in different environments or under different conditions.Some of the tests that the engineers might perform to validate their theories include:Simulation tests: Simulation tests are computer-based tests that allow engineers to test the robot's behavior and movement in a virtual environment. Engineers can create different scenarios and see how the robot performs in each scenario. This allows them to fine-tune the robot's programming before it is built.
learn more about Robotics engineers
https://brainly.com/question/22788959
#SPJ11
The spring has a spring of 240 n/m how much potential energy is stored in the spring as it is stretched 0.20
To calculate the potential energy stored in a stretched spring, you can use the formula:
Potential Energy (PE) = (1/2) * k * x^2
Where:
k is the spring constant, which is given as 240 N/m in this case.
x is the displacement or stretch of the spring from its equilibrium position, given as 0.20 m in this case.
Substituting the given values into the formula:
PE = (1/2) * 240 * (0.20)^2
= 4.8 J
Therefore, the potential energy stored in the spring as it is stretched 0.20 m is 4.8 joules.
Learn more about spring potential energy here:
brainly.com/question/12528339
#SPJ11
which model best describes how gravity causes star formation? please help<3
The model that best describes how gravity causes star formation is the gravitational collapse model. According to this model, stars form from the gravitational collapse of dense regions within interstellar clouds of gas and dust.
The process begins with a molecular cloud, which is a large cloud of gas and dust in space. Within these molecular clouds, there are regions that are denser than their surroundings, often referred to as dense cores or protostellar cores. These dense cores can contain several times the mass of the Sun.
Under the influence of gravity, the dense core begins to collapse inward. As the core collapses, it becomes denser and hotter due to the increasing pressure. The gravitational energy is converted into thermal energy, raising the temperature and causing the core to heat up.
As the temperature rises, nuclear fusion reactions start to occur at the core's center. These fusion reactions convert hydrogen into helium, releasing enormous amounts of energy in the form of light and heat. This marks the birth of a star, as it begins to emit its own light and heat.
Gravity plays a crucial role throughout this process, providing the force necessary to overcome the outward pressure and hold the collapsing material together. The gravitational collapse model explains how the force of gravity initiates the collapse of interstellar clouds, leading to the formation of stars.
It is important to note that other factors, such as the presence of magnetic fields and turbulence within the cloud, also influence the star formation process. However, gravity is the primary driving force behind the initial collapse and subsequent formation of stars.
To know more about Energy visit-
brainly.com/question/1932868
#SPJ11
After repeated pairings of a metronome with meat powder, Pavlov found that a dog will salivate when the metronome is presented. Food is the ____ and Salivation in reaction to the food is the ______:
The food is the unconditioned stimulus (US), and salivation in reaction to the food is the unconditioned response (UR).
In classical conditioning, the terms used to describe the components of the process are as follows: Unconditioned Stimulus (US): The unconditioned stimulus is the stimulus that naturally and automatically triggers a response without any prior conditioning. In this case, the food is the unconditioned stimulus (US) because it naturally elicits the response of salivation in the dog. Unconditioned Response (UR): The unconditioned response is the unlearned response that occurs naturally in reaction to the unconditioned stimulus. Salivation in reaction to the food is the unconditioned response (UR) because it is an innate response triggered by the presentation of the food. Conditioned Stimulus (CS): The conditioned stimulus is a previously neutral stimulus that, through association with the unconditioned stimulus, comes to elicit a conditioned response. In this case, the metronome is the conditioned stimulus (CS) because, after repeated pairings with the food (unconditioned stimulus), it starts to evoke a salivary response. Conditioned Response (CR): The conditioned response is the learned response that occurs due to the conditioned stimulus. Salivation in reaction to the metronome is the conditioned response (CR) because it is a learned response that is elicited by the conditioned stimulus (metronome) after conditioning has taken place.
Learn more about metronome here:
https://brainly.com/question/15086157
#SPJ11
Driving a car 100m requires the same amount of _____ as pushing it 100m by hand. A. PowerB. Power and EnergyC. TimeD. Work
Driving a car 100m requires the same amount of work as pushing it 100m by hand as the concept of work in physics refers to the transfer of energy when a force is applied over a certain distance.
When driving a car or pushing it by hand, the same amount of work is done because the distance covered is the same. However, it's important to note that the power required to accomplish this work may differ, as power is the rate at which work is done or energy is transferred. So, while the work is the same, the power required for driving a car is typically much higher than the power needed to push it by hand.
To know more about energy, visit
https://brainly.com/question/18771704
#SPJ11
Which statement does not describe a scientific law?
They have been observed by many scientists and are widely accepted.
They explain how and why events occur in the natural world.
They apply to all fields of science.
They describe observations made in the natural world.
Answer:
they explained now and why events occur in the natural word
A force of 25 N is applied to a screwdriver to pry the lid off of a can of paint. The screwdriver applies 75 N of force to the lid. What is the mechanical advantage of the screwdriver?
Answer:
The mechanical advantage of the screwdriver is 3.
Explanation:
The mechanical advantage can be calculated using the formula: mechanical advantage = output force / input force. In this case, the output force is 75 N (the force applied by the screwdriver to the lid), and the input force is 25 N (the force applied to the screwdriver).
Therefore, the mechanical advantage is:
mechanical advantage = 75 N / 25 N = 3.
Hence, the mechanical advantage of the screwdriver is 3.
Learn more about mechanical advantage here: https://brainly.com/question/32030248
#SPJ11.
absorption takes place when the ray strikes the surface at right angle
Absorption of light or radiation occurs when the incident ray strikes the surface at an oblique angle rather than a right angle. When light or radiation strikes a surface at a right angle (perpendicular to the surface), it is more likely to be reflected or transmitted rather than absorbed.
When light strikes a surface at an oblique angle, it has a higher chance of being absorbed by the material. The absorption process involves the transfer of energy from the incident light to the atoms or molecules of the material, causing them to vibrate or undergo electronic transitions, which leads to an increase in the internal energy of the material. It's important to note that the amount of absorption depends on various factors such as the properties of the material, the wavelength of the incident light, and the angle of incidence. Materials have different absorption characteristics at different wavelengths, and the angle of incidence can affect the path length and the interaction of light with the material, influencing the absorption process.
To learn more about light, https://brainly.com/question/31040837
#SPJ11
What is the medical applications of maxwell's wheel experiment ?
The medical applications of Maxwell's wheel experiment will be; Vestibular Assessment, Physical Therapy, Hand-eye Coordination Training, and Kinematic Analysis.
Vestibular Assessment; The rotating motion of Maxwell's wheel can be used to assess vestibular function in individuals with balance disorders or vertigo. By observing the direction and duration of nystagmus (involuntary eye movement), healthcare professionals can gain insights into the functioning of the vestibular system.
Rehabilitation and Physical Therapy; Maxwell's wheel can be used in physical therapy and rehabilitation settings to assess and improve motor coordination, proprioception, and balance control. Patients can be instructed to manipulate the wheel to target specific muscle groups and enhance fine motor skills.
Hand-eye Coordination Training; The precise control required to manipulate the spinning disk in Maxwell's wheel experiment can be utilized for hand-eye coordination training. This is particularly relevant for surgeons and other medical professionals who require dexterity and accuracy in their procedures.
Kinematic Analysis; The motion of Maxwell's wheel can be recorded and analyzed using video or motion capture systems. This analysis can provide insights into the kinematics of different body movements, such as joint angles, velocity, and acceleration.
To know more about Maxwell's wheel here
https://brainly.com/question/31420537
#SPJ4
In applying the right-hand rule as discussed in this section, which is true?.
The right-hand rule is used in the field of electromagnetism. It is a method for determining the direction of a magnetic field related to the direction of the electric current that is creating it.
The right-hand rule is also used to determine the direction of the force on a charged particle moving in a magnetic field. There are two types of right-hand rules in electromagnetism: the right-hand rule for magnetic field direction and the right-hand rule for force direction. The correct statement regarding applying the right-hand rule is that if we hold a current-carrying conductor in the right hand, then the direction of the thumb points towards the direction of the current, then the curling of the fingers represents the direction of the magnetic field around the conductor. This means that if the current flow is in the upward direction in the conductor, then the magnetic field is in the counterclockwise direction around the conductor, and if the current is flowing in the downward direction, then the magnetic field is in the clockwise direction around the conductor. In the case of a loop conductor, we can determine the direction of the magnetic field inside the loop by using the right-hand rule. In this case, if we wrap the fingers of the right hand around the loop in the direction of the current flow, then the direction in which the thumb points gives us the direction of the magnetic field inside the loop. The right-hand rule is a very useful tool in understanding and visualizing the interactions between electric currents and magnetic fields. It is also an essential tool for designing and building electrical devices such as motors and generators. The right-hand rule is a fundamental concept in electromagnetism and is used extensively in many areas of science and engineering.
The right-hand rule is used to determine the direction of a magnetic field related to the direction of the electric current that is creating it. The correct statement regarding applying the right-hand rule is that if we hold a current-carrying conductor in the right hand, then the direction of the thumb points towards the direction of the current, then the curling of the fingers represents the direction of the magnetic field around the conductor. It is a fundamental concept in electromagnetism and is used extensively in many areas of science and engineering.
To know more about magnetic field click:
brainly.com/question/14848188
#SPJ11
A circular swimming pool has a radius of 28 ft. There is a path all the way around the pool that is 4 ft wide. A fence is going to be built around the outside edge of the pool path about how many feet of fencing are needed to go around the pool path use 3. 14 for π 28 ft 4 ft.
Answer:
201.06 feet of fencing are needed to go around the pool path use 3. 14 for π 28 ft 4 ft.
Explanation:
To calculate the total length of fencing needed to go around the pool path, we need to consider the circumference of the outer edge of the path.
The circumference of a circle can be calculated using the formula: C = 2πr, where C is the circumference, π is approximately 3.14, and r is the radius of the circle.
Given that the radius of the circular swimming pool is 28 ft, the radius of the outer edge of the path would be 28 ft + 4 ft (path width) = 32 ft.
Substituting this value into the formula, we can calculate the circumference of the outer edge of the path:
C = 2 * 3.14 * 32 ft ≈ 201.06 ft
Therefore, approximately 201.06 feet of fencing are needed to go around the pool path.
Learn more about circumference of a circle here:
https://brainly.com/question/17130827
#SPJ11
Inertia is the natural tendency of every object to resist change to either speed or direction. Describe a way in which you observe this in your everyday life.
Inertia refers to the natural tendency of every object to resist any change in either speed or direction. Every object tends to maintain its state of motion until an external force acts on it.
Inertia is an essential concept in physics, and it can be observed in everyday life. Here is how you can observe inertia in your everyday life:
When you are in a moving car, and the driver suddenly stops, your body tends to move forward. This is because of inertia. Your body is already in motion, and when the car stops, your body tends to keep moving in the same direction. The seatbelt helps to prevent this movement by exerting a force on your body in the opposite direction.
When you are on a merry-go-round and it starts spinning, you tend to feel a force pushing you away from the center of the ride. This is also due to inertia. Your body is already in motion, and when the ride starts spinning, your body tends to keep moving in the same direction. The force that pushes you away from the center of the ride is known as the centrifugal force.
When you are playing a game of pool, and you hit the cue ball, it tends to keep moving until it comes into contact with another ball or hits the wall of the table. This is also due to inertia. The cue ball is already in motion, and it tends to maintain its state of motion until it comes into contact with another object or hits the wall of the table.
These are just a few examples of how you can observe inertia in your everyday life.
learn more about force here
https://brainly.com/question/30236242
#SPJ11
You push a block with your hand into the wall to hold it stationary. What are the direction of normal force and friction force respectively on the block?.
When you push a block with your hand into the wall to hold it stationary, the direction of the normal force and friction force respectively on the block are as follows: Direction of normal force: It is the force that is exerted perpendicular to the surface of contact between the block and the wall.
In this case, the normal force acts in the upward direction against the weight of the block. It is responsible for balancing the weight of the block and preventing it from sinking into the wall.
Direction of friction force:
It is the force that opposes the motion of the block and acts parallel to the surface of contact between the block and the wall.
The friction force acts in the backward direction opposite to the force applied by the hand on the block.
It is responsible for holding the block stationary and preventing it from sliding down the wall.
Know more about direction here:
https://brainly.com/question/28108225
#SPJ11
A 0.27-kg volleyball has a kinetic energy of 1.8 J. What is the speed of the volleyball?
the speed of the volleyball is 3.85 m/s.
Given: The mass of the volleyball m = 0.27-kg;
The kinetic energy of the volleyball KE = 1.8 J
We know that the kinetic energy of an object is given as:
KE = (1/2)mv²
Where,KE = Kinetic energy of the object
m = Mass of the object
v = Velocity of the object
Substituting the given values in the equation,1.8 = (1/2) × 0.27 × v²
On simplifying, we get:
v² = (2 × 1.8) / 0.27v² = 4 / 0.27v² = 14.81
Taking the square root of both sides, we get:
v = 3.85 m/s
Therefore, the speed of the volleyball is 3.85 m/s.
learn more about speed here
https://brainly.com/question/13943409
#SPJ11
Which word in the statement of this problem allows you to assume that the table is frictionless?.
The word "horizontal" in the statement of the problem allows us to assume that the table is frictionless.
When we say that the table is horizontal, it implies that there is no friction force acting on the surface of the table.
Friction is a force that opposes motion between surfaces that are in contact with each other. In the absence of any frictional force, the object will continue to move at a constant velocity.
The absence of frictional force is a necessary condition to consider the motion of the object as the motion under ideal conditions.
Hence, the word "horizontal" in the statement of the problem allows us to assume that the table is frictionless.
Know more about frictionless here:
https://brainly.com/question/30854343
#SPJ11
What is the period of oscillation of a pendulum that is. 5m long?
. 26 s
1. 42 s
6. 28 s
13. 9 s
Answer:1.42
Explanation:
The athlete at point A runs 150m east, then 70m west and then 100 m east. How do i Determine the resultant force acting on the object?
To determine the resultant force acting on the object we need to find the net displacement. We can find the net displacement by subtracting the total distance travelled in the opposite direction (west) from the total distance travelled in the east direction. We can use this formula: Net displacement = Total displacement in the East direction - Total displacement in the West direction. Once we find the net displacement we can calculate the resultant force acting on the object.
The athlete runs 150m towards east, 70m towards west and again 100m towards east. Thus, total displacement in the East direction = 150m + 100m = 250mTotal displacement in the West direction = 70mNet displacement = Total displacement in the East direction - Total displacement in the West direction= 250m - 70m= 180mTherefore, the net displacement of the athlete is 180m towards east.
This displacement is called as the resultant displacement. Since the athlete has been moving towards east in the positive direction and towards west in the negative direction, thus his resultant displacement is the sum of the positive and negative distances he covered.
learn more about resultant force
https://brainly.com/question/25239010
#SPJ11
Calculate the volume of the cone.
What is the volume of a cone with a height of 27 cm
and a radius of 13 cm? Round your answer to the
nearest tenth.
Use the button on your calculator to complete this
problem.
V=
I cm²
27 cm
13 cm
Rounded to the nearest tenth, the volume of the cone is approximately 4790.6 cm^3.
To calculate the volume of a cone, you can use the formula:
V = (1/3) * π * r^2 * h
Where:
V is the volume of the cone
π is the mathematical constant pi (approximately 3.14159)
r is the radius of the cone's base
h is the height of the cone
Given:
Height (h) = 27 cm
Radius (r) = 13 cm
Let's substitute the values into the formula and calculate the volume:
V = (1/3) * π * (13 cm)^2 * 27 cm
V ≈ 1/3 * 3.14159 * 169 cm^2 * 27 cm
V ≈ 1/3 * 3.14159 * 4563 cm^3
V ≈ 4790.63789 cm^3
Rounded to the nearest tenth, the volume of the cone is approximately 4790.6 cm^3.
To calculate the volume of a cone, you can use the formula:
V = (1/3) * π * r^2 * h
Where:
V is the volume of the cone
π is the mathematical constant pi (approximately 3.14159)
r is the radius of the cone's base
h is the height of the cone
Given:
Height (h) = 27 cm
Radius (r) = 13 cm
Let's substitute the values into the formula and calculate the volume:
V = (1/3) * π * (13 cm)^2 * 27 cm
V ≈ 1/3 * 3.14159 * 169 cm^2 * 27 cm
V ≈ 1/3 * 3.14159 * 4563 cm^3
V ≈ 4790.63789 cm^3
Learn more about the volume here:
https://brainly.com/question/31746007
#SPJ11
An inflatable toy starts with 1. 05 moles of air and a volume of 5. 17 liters. When fully inflated, the volume is 8. 00 liters. If the pressure and temperature inside the toy don’t change, how many moles of air does the toy now contain? A. 2. 05 mol B. 1. 62 mol C. 1. 55 mol D. 0. 679 mol.
The number of moles of air currently present in toy, given that the pressure and temperature are constant is 1.62 mole (option B)
How do i determine the mole air currently present?The following data were obtained from the question:
Initial mole (n₁) = 1.05 moleInitial volume (V₁) = 5.17 litersPressure = ConstantTemperature = ConstantNew volume (V₂) = 8.00 litersNew mole (n₂) =?The new mole of the air currently present can be obtained as follow:
V₁ / n₁ = V₂ / n₂
5.17 / 1.05 = 8 / n₂
Cross multiply
5.17 × n₂ = 1.05 × 8
Divide both side by 5.17
n₂ = (1.05 × 8) / 5.17
= 1.62 mole
Thus, the number of mole currently present is 1.62 mole (option B)
Learn more about number of mole:
https://brainly.com/question/29927685
#SPJ4
A jogger runs 10 miles North in 2 hours. What is the Joggers velocity?
The jogger's velocity would be 5 miles per hour North when he runs 10 miles North in 2 hours.
Velocity is a vector quantity that represents the rate at which an object changes its position. It includes both the magnitude (speed) and the direction of motion. In this case, the jogger runs 10 miles North in 2 hours.
To calculate the velocity, we divide the displacement by the time taken. The displacement is the change in position, which in this case is 10 miles North. The time taken is 2 hours. Therefore, the velocity is 10 miles divided by 2 hours, resulting in a velocity of 5 miles per hour North.
It's important to note that velocity is a vector quantity and includes both magnitude and direction. In this case, the magnitude is 5 miles per hour, and the direction is North.
To know more about , velocity, click here https://brainly.com/question/30559316
#SPJ11
In which of the following scenarios will the frequency decrease? Select all that apply. A. Speed decreases and wavelength remains constant. B. Speed remains constant and wavelength decreases. C. Speed increases by a factor of 2 and wavelength decreases by a factor of 0. 5. D. Speed decreases by a factor of 4 and wavelength increases by a factor of 2. E. Speed remains constant and wavelength increases
The option A is correct. When the speed of a wave remains constant and the wavelength of the wave increases, the frequency of the wave decreases.
The frequency is a measure of the number of waves that pass a point in a given period of time and the speed of a wave is inversely proportional to the frequency. As a result, when the speed of a wave decreases, the frequency of the wave decreases. When the wavelength of a wave decreases, the frequency of the wave increases. Therefore, option B is incorrect. When the speed of a wave increases by a factor of 2 and the wavelength of the wave decreases by a factor of 0.5, the frequency of the wave remains constant.
To learn more about frequency click here https://brainly.com/question/31938473
#SPJ11
A stone is tied to a string and swung along the path of a vertical circle at constant speed. When is the string most likely to break?.
When a stone is tied to a string and swung along the path of a vertical circle at a constant speed, the string is most likely to break at the topmost point of the circle.
The tension in the string is maximum at this point because the weight of the stone is acting in the downward direction, while the tension in the string is acting in the upward direction. The tension in the string is given by the formula: T = mv² / r + mg Where T is the tension in the string, m is the mass of the stone, v is the speed of the stone, r is the radius of the circle, and g is the acceleration due to gravity. The tension in the string is maximum at the topmost point of the circle because the speed of the stone is zero at this point, and the tension in the string is only due to the weight of the stone, which is acting in the downward direction. Therefore, the string is most likely to break at the topmost point of the circle when the stone is swung along the path of a vertical circle at a constant speed. A stone is tied to a string and swung along the path of a vertical circle at a constant speed. The tension in the string is given by the formula T = mv² / r + mg, where T is the tension in the string, m is the mass of the stone, v is the speed of the stone, r is the radius of the circle, and g is the acceleration due to gravity. The tension in the string is maximum at the topmost point of the circle because the speed of the stone is zero at this point, and the tension in the string is only due to the weight of the stone, which is acting in the downward direction. Therefore, the string is most likely to break at the topmost point of the circle when the stone is swung along the path of a vertical circle at a constant speed.
In conclusion, when a stone is tied to a string and swung along the path of a vertical circle at a constant speed, the string is most likely to break at the topmost point of the circle. The tension in the string is maximum at this point because the weight of the stone is acting in the downward direction, while the tension in the string is acting in the upward direction.
To know more about acceleration due to gravity click:
brainly.com/question/21775164
#SPJ11
____________is a cross section of two infinite lines of charge that extend out of the page. Both have linear charge density l. Find an expression for the electric field strength E at height y above the midpoint between the lines.
To find the expression for the electric field strength E at height y above the midpoint between two infinite lines of charge with linear charge density λ, we can use the principle of superposition.
Consider a small section of length dl on one of the lines of charge. The electric field dE produced by this section at point P (midpoint) is given by Coulomb's law:
dE = (k * λ * dl) / (2πε₀r)
where k is Coulomb's constant, ε₀ is the permittivity of free space, and r is the distance from the section dl to point P.
Since the lines of charge are infinite, the electric field contributions from all the sections add up. We integrate this expression over the length of the line of charge:
E = ∫ (k * λ * dl) / (2πε₀r)
Now, we need to express r in terms of y and dl. As the two lines of charge are symmetrically placed with respect to the midpoint,
we have r = √(y² + (dl/2)²).
Substituting this into the integral expression, we have:
E = ∫ (k * λ * dl) / (2πε₀√(y² + (dl/2)²))
Integrating over the length of the line of charge will give the final expression for the electric field strength E at height y above the midpoint between the lines.
Please note that the specific form of the integral will depend on the geometry of the charge distribution, such as the separation between the lines of charge and their orientation.
Learn more about Coulomb's law here:
brainly.com/question/506926
#SPJ11
List 6 stories that are currently in the news that humorists are drawing cartoons about
As an AI language model, I don't have real-time access to current news or the ability to browse the internet. My training data only goes up until September 2021, so I cannot provide you with the most up-to-date information on stories that humorists are currently drawing cartoons about.
However, I can give you a general idea of the types of stories that often attract the attention of humorists and inspire them to create cartoons. Please note that these examples may not be specific to the current news cycle:
Political figures: Humorists often create cartoons about politicians and their actions, speeches, or scandals.
Social issues: Topics like climate change, inequality, or social movements can be a source of inspiration for satirical cartoons.
Pop culture: Current trends, celebrities, or popular events often serve as material for humorists to create cartoons that capture the zeitgeist.
Technology and internet culture: The impact of technology, social media, and the internet on society can provide humorous fodder for cartoonists.
Global events: Major international news, such as elections, conflicts, or diplomatic incidents, may be satirized in cartoons.
Sports: Significant sporting events or controversies in the sports world can be the subject of humorous cartoons.
To stay up to date with the latest news and the cartoons being produced, I recommend checking out news websites, satirical publications, or following humorists and cartoonists on social media platforms.
to know more about language visit:
https://brainly.in/question/49668539
#spj11
Class 8 Cbse Ncert Revision Question's1) When a ball pen refill is rubbed vigorously against polythene, it attractssmall pieces of paper. What makes the refill attract paper?2) Write the use of an electroscope. 3) Explain the purification of copper using electrolysis with the help of anelectric circuit. 4) Write any two uses of electrolysis. 5) Why are multiple images formed when two mirrors are placed at rightangles to each other?6) Why should we not stand under a tree when there is thunder andlightning?7) We electroplate metals with chromium to make car parts, bath taps,kitchen gas burners etc. Why is chromium itself not used for makingthese materials?8) Describe the chemical effect of current on water with the help of adiagram. 9)Paheli wants to deposit silver on an iron spoon. She took silver nitrate(AgNO3) solution in a beaker and set up a simple circuit forelectroplating. Which terminal of the battery should the spoon beconnected to? What material should the other electrode be made of?10) An electric current is passed through a conducting solution. List anythree possible observations. 11) What happens to light when it gets dispersed? Give an example. 12) How are the eyes of the day birds different from night birds?
1) When a ball pen refill is rubbed vigorously against polythene, it attracts small pieces of paper due to the phenomenon of static electricity. The friction between the refill and polythene causes an exchange of electrons, resulting in a charge imbalance. The refill becomes negatively charged, while the polythene becomes positively charged. The negatively charged refill then attracts the positively charged paper bits.
2) An electroscope is used to detect the presence and magnitude of electric charges. It consists of a metal rod with two thin metal leaves attached to the bottom. When a charged object is brought close to the electroscope, the leaves either repel or attract each other, indicating the presence of a charge. By observing the movement of the leaves, we can determine whether the charge is positive or negative and get an idea of its strength.
3) The purification of copper using electrolysis involves passing an electric current through a copper sulfate solution with impure copper as the anode and a pure copper plate as the cathode. The electric current causes the copper ions from the impure copper to move toward the cathode, where they get reduced and deposit as pure copper. The impurities settle at the bottom of the anode as a residue called anode mud.
4) Electrolysis has various applications, including:
- Electroplating: It is used to deposit a layer of metal onto another object for protection, decoration, or other purposes.
- Electrorefining: It is employed to purify metals by removing impurities through electrolysis.
- Electrolytic cells: They are utilized in the production of chemicals and metals, such as aluminum and chlorine.
5) Multiple images are formed when two mirrors are placed at right angles to each other due to the phenomenon of reflection. Each mirror reflects the incident light rays, creating a chain of reflections. The number of images formed depends on the angle between the mirrors and the observer's position. For mirrors at right angles, three images are typically formed: two symmetrical images on one side and a virtual image on the other side.
Learn more about static electricity here:
brainly.com/question/24160155
#SPJ11
