A 900.0kg car is traveling at 11.0m/s. What is the momentum of this car?

Answers

Answer 1

The momentum of the car is 9900 kg m/s.

What is momentum?

The momentum of an object is defined as the product of its mass and velocity. In this case, the momentum of the car can be calculated using the following formula:

Momentum = mass x velocity

Here, the mass of the car is 900.0 kg and its velocity is 11.0 m/s. Substituting these values into the formula, we get:

Momentum = 900.0 kg x 11.0 m/s

Momentum = 9900 kg m/s

Therefore, the momentum of the car is 9900 kg m/s.

Note that the units of momentum are kilogram meters per second (kg m/s), which are derived from the units of mass (kg) and velocity (m/s). Momentum is a vector quantity, meaning it has both magnitude and direction, and its direction is the same as the direction of motion of the object.

To know more about momentum visit :-

https://brainly.com/question/1042017

#SPJ1


Related Questions

an open vertical tube has water in it. a tuning fork vibrates over its mouth. as the water level is lowered in the tube, the seventh resonance is heard when the water level is 217.75 cm below the top of the tube.

Answers

The speed of sound is found out to be 349.4 ms⁻¹ from the frequency of the seventh resonance heard when the water level is 217.75 cm below the top of the tube.

What is the frequency?

Frequency of wave:

v = nλ

where, v = speed of sound, n = frequency, λ = wavelength

Speed of sound:

v = frequency n × wavelength λ

Frequency, n = v/λ

Wavelength, λ = v/n

The 7th resonance frequency of the tuning fork is given by:

n = 7 × f

where, f is the frequency of the tuning fork

Speed of sound, v = nλ

Speed of sound, v = 7fλ

Speed of sound, v = 7 × 256 Hz × λ

λ = 1.3671 m

Distance travelled by the sound wave in the water column is L = h + l

where, h = length of the air column and l = length of water column where the resonance was heard.

L = h + l

L = 217.75 cm + 50 cm

L = 267.75 cm = 2.6775 m

Length of the air column, h = L - l

where, l = length of water column where the resonance was heard.

h = 2.6775 m - 0.5 m

h = 2.1775 m

Wavelength of sound wave in air column, λ₁ = 4h

λ₁ = 4 × 2.1775 m

λ₁ = 8.71 m

Frequency of the sound wave in air column is given by:

n = v/λ₁

n = 349.4 ms⁻¹ / 8.71 m

n = 40.112 Hz

The 7th resonance frequency of the tuning fork is given by:

n = 7 × f

40.112 Hz = 7 × f

Frequency of the tuning fork, f = 5.73 Hz.

Learn more about Frequency here:

https://brainly.com/question/14316711

#SPJ11

The velocity of a particle moving along the x axis changes from vi to vs For which values of vi and vf is the total work done on the particle positive? vi = 5 m / s, vf = - 2 m / s vi = - 2 m / s, vf = - 5 m / s vi = 5 m / s, vf = 2 m / s vi = - 5 m / s, vf = - 2 m / s vi = - 5 m / s, vf = 2 m / s

Answers

The total work done on a particle is given by the formula:

W = (1/2)mvf^2 - (1/2)mvi^2

where m is the mass of the particle, vi is the initial velocity, and vf is the final velocity.

For vi = 5 m/s and vf = 2 m/s, the final velocity is less than the initial velocity, so the total work is positive.

For vi = -2 m/s and vf = -5 m/s, the final velocity is less than the initial velocity, so the total work is positive.

For vi = -5 m/s and vf = 2 m/s, the final velocity is greater than the initial velocity, so the total work is negative.

For vi = 5 m/s and vf = -2 m/s, the final velocity is greater than the initial velocity, so the total work is negative.

For vi = -5 m/s and vf = -2 m/s, the final velocity is less than the initial velocity, so the total work is positive.

Therefore, the total work done on the particle is positive for vi = 5 m/s and vf = 2 m/s, and for vi = -2 m/s and vf = -5 m/s.

What   works ?

In order for work to be done, there must be a displacement of the object in the direction of the force applied. If the force and displacement are perpendicular, then no work is done.

Work can be positive, negative, or zero, depending on the direction of the force and the displacement. Positive work is done when the force and the displacement are in the same direction, negative work is done when they are in opposite directions, and zero work is done when there is no displacement or when the force and displacement are perpendicular.

Work is a transfer of energy, and as such it can change the kinetic energy, potential energy, or both of an object.

To know more about Work visit :

https://brainly.com/question/18094932

#SPJ1

A gas is compressed at a constant pressure from a volume of 10 m3 to a volume of 4 m3 , then work done on the system is:
a) nRT ln 1/6
b) nRT In2/5
c) nRT In 5/2
d) nRT In 6

Answers

None of the answer options provided are correct as they all involve calculations that assume certain values for the pressure, volume, and temperature of the gas.

What is Constant Pressure?

Constant pressure is a thermodynamic process in which the pressure of a system remains constant during the process. This means that any change in volume or temperature of the system must be accompanied by a corresponding change in some other property, such as the amount of heat added or removed from the system.

Since the gas is compressed at a constant pressure, the work done on the system can be calculated as:

W = -PΔV

In this case, P is constant, so we have:

W = -P(V2 - V1)

W = -P(4 m^3 - 10 m^3)

W = -P(-6 m^3)

W = 6P m^3

Since we are not given any information about the type of gas or its properties, we cannot use the ideal gas law to calculate the pressure P. Therefore, we cannot determine the exact value of the work done on the system.

Learn more about Constant Pressure from given link

https://brainly.com/question/2139620

#SPJ1

A copper water tank of mass 20 kg contains 150 kg of water at 15°C. Calculate the energy needed to heat the water and the tanks to 55°C

Answers

The energy needed to heat the water and the copper tank to 55°C is 25,083,080 J.

Q = mCΔT

m = 150 kg (mass of water)

C = 4.18 J/g°C (specific heat capacity of water)

ΔT = 55°C - 15°C = 40°C (change in temperature)

Using the formula, we get:

[tex]Q_{water}[/tex] = mCΔT

[tex]Q_{water}[/tex] = (150 kg) x (4.18 J/g°C) x (40°C)

[tex]Q_{water}[/tex] = 25,080,000 J

m = 20 kg (mass of tank)

C = 0.385 J/g°C (specific heat capacity of copper)

ΔT = 55°C - 15°C = 40°C (change in temperature)

Using the formula, we get:

[tex]Q_{tank}[/tex] = mCΔT

[tex]Q_{tank}[/tex] = (20 kg) x (0.385 J/g°C) x (40°C)

[tex]Q_{tank}[/tex]= 3080 J

Finally, we can add the two energies together to get the total energy needed:

[tex]Q_{total}[/tex] = [tex]Q_{water}[/tex] [tex]+[/tex] [tex]Q_{tank}[/tex]

[tex]Q_{total}[/tex] [tex]= 25,080,000 J + 3080 J[/tex]

[tex]Q_{total}[/tex] [tex]= 25,083,080 J[/tex]

Energy is a fundamental concept that refers to the ability of a physical system to do work or cause a change. It is a scalar quantity that is measured in units of joules (J) in the International System of Units (SI). According to the law of conservation of energy, energy cannot be created or destroyed, but it can be transformed from one form to another. This means that the total amount of energy in a closed system remains constant.

Energy is a crucial concept in many areas of physics, including mechanics, thermodynamics, and electromagnetism. Understanding energy is essential for understanding how the physical world works, and it has numerous applications in technology and everyday life, from powering our homes and vehicles to the production of food and the functioning of our bodies.

To learn more about Energy visit here:

brainly.com/question/2409175

#SPJ4

1 80 kg scaffold is 5.80 m long. it is hanging with two wires, one from each end. a 580 kg box sits 1 m from the left end. what is the tension in the right hand side wire?

Answers

The tension in the right-hand side wire is 6525 N.

Given:

Weight of the scaffold = 180 kgLength of the scaffold = 5.8 mWeight of the box = 580 kgDistance of the box from left end = 1 mLet the tension in the left wire = T1Let the tension in the right wire = T2

To find: Tension in the right-hand side wireWe know that the sum of forces acting in a vertical direction should be equal to 0 as there is no acceleration in the vertical direction. ∑Fv = 0In the horizontal direction, there are no forces acting on the system.

∑Fh = 0Now considering forces in the vertical direction: T1 + T2 = (Weight of scaffold + Weight of the box) gT1 + T2 = (180 + 580) x 9.8T1 + T2 = 7644 N1. From the diagram, we can see that the box is nearer to the left side. Hence, the tension force in the left wire is greater than the tension force in the right wire.

T1 > T22. Let's take moments about the right end of the scaffold as shown in the figure below.

∑Mr = 0T1 × 5.8 = T2 × 1T2 = 5.8/1 × T1T2 = 5.8T1

Now, we can substitute the value of T2 in equation (1):

T1 + T2 = 7644N6.8 T1 = 7644 N  T1 = 1125 N

To find T2, we can substitute the value of T1 in equation (2):

T2 = 5.8 × T1T2 = 5.8 × 1125 N T2 = 6525 N

Therefore, the tension in the right-hand side wire is 6525 N.

Learn more tension: https://brainly.com/question/4001686

#SPJ11

Consider the spectra of the two main sequence stars below (Star 1 on the left and Star 2 on the right) and sort the statements into the true or false bins. The intensity axes are not necessarily on the same scale. 350 450 550 Wavelength (nm) 350 45Q750 650 750 Wavelength (nm) true false Star 1 has a longer lifetime than Star 2 Star 2 is bluer than Star 1 Star 2 has a lower mass than Star 1 Star 1 has prominent hydrogen lines Star 2 has a higher luminosity than Star 1 Star 2 is cooler than Star 1.

Answers

. Additionally, Star 1 has prominent hydrogen lines, indicating a lower temperature than Star 2. Therefore, the statements can be sorted into the true and false bins as indicated above.

True: Star 1 has a longer lifetime than Star 2; Star 2 is bluer than Star 1; Star 2 has a lower mass than Star 1; Star 1 has prominent hydrogen lines.

False: Star 2 has a higher luminosity than Star 1; Star 2 is cooler than Star 1.

The spectra of the two main sequence stars illustrate some differences between the two stars. Star 1 is on the left and has a longer lifetime than Star 2, which is on the right. This is evident from the intensity axes that are not on the same scale. Star 2 has a lower mass than Star 1, is bluer than Star 1, and has a lower luminosity

for such more questions on hydrogen lines

https://brainly.com/question/30461609

#SPJ11

Which of the following characterizes the Kuiper belt?
A. It is a disk-like region between the outer planets and the Oort cloud.
B. It is up to 100,000 AU in size and spherical in shape.
C. It lies between the orbits of Mars and Jupiter.
D. It is a stable region just ahead of Jupiter in its orbit.
E. It is the region occupied by the Earth-crossing Apollo asteroids.

Answers

The Kuiper belt is a disk-like region between the outer planets and the Oort cloud. Thus, option A is correct


The Kuiper belt, also known as the trans-Neptunian region, is a doughnut-shaped region of space beyond Neptune that is home to an estimated 100,000 tiny, icy objects.

It is named after Dutch-American astronomer Gerard Kuiper, who first proposed its existence in 1951.

The belt ranges in distance from 30 to 50 astronomical units (AU) from the Sun, which is about 2.8 to 4.7 billion miles away.

The Kuiper belt objects are believed to be remnants from the formation of the solar system. They are small and mostly made up of ice and dust, similar to comets.

Some Kuiper belt objects, such as Pluto and Eris, are classified as dwarf planets.

Learn more about the Kuiper belt here:

https://brainly.com/question/3955749

#SPJ11

A convex lens is shown here with an arrow in the left indicating the light moving through the lens. Assuming that
the lens is made of material that has a higher density than the air, predict the direction of the light after it passes
through the lens.

A The light will bend downward significantly as is indicated by arrow D.

B The light will bend upward as is indicated by arrow A.

C The light will continue on its straight path, as indicated by arrow B.

D The light will bend downward slightly as is indicated by arrow C.



Picture

Answers

Answer:

B The light will bend upward as is indicated by arrow A.

Explanation:

I just did the progress learning test

the potential difference across the ion channel is 70 mv . what is the power dissipation in the channel?

Answers

The power dissipation in the ion channel is 4.9 mW given that the potential difference across the ion channel is 70 mv

The power dissipated by a resistor is given by the formula:P = V² / RwhereP = PowerV = VoltageR = Resistance

The power dissipated in the ion channel is unknown. However, we can consider the ion channel to have a resistance of 1 Ω. This is because the resistance of an ion channel is very small and close to zero. So, we can assume the resistance of the ion channel as 1 Ω.As we know the potential difference across the ion channel, we can use the above formula to find the power dissipated in the ion channel.P = (70 mV)² / 1 ΩP = 0.0049 W = 4.9 mW

Therefore, the power dissipation in the ion channel is 4.9 mW.

More on power: https://brainly.com/question/29347465

#SPJ11

Imagine another solar system, with a star of the same mass as the Sun. Suppose a planet with a mass twice that of Earth (2MEarth) orbits at a distance of 1 AU from the star. What is the orbital period of this planet? Hint: Think about how the mass of the Sun compares with the mass of the Earth. a. 3 months b. 6 months
c. 1 year d. 2 years
e. It would not be able to orbit at this distance.

Answers

The correct answer is option D.2 years

What is Kepler's third law of planetary motion?

According to Kepler's Third Law of Planetary Motion, T² is proportional to r³, where T is the period of revolution of the planet and r is the distance between the planet and the star.

In order to solve for T,  

AU = 1

Astronomical Unit = the average distance between the Earth and the Sun = 149.6 million kilometres

Therefore, the planet is orbiting at a distance of 149.6 million kilometres from the star.

Substituting the values of r and solving for

T².T² ∝ r³T² ∝ (149.6)³T²

= (149.6)³T²

= 3.522 x 10¹²T

= √3.522 x 10^¹²T

= 1.87 x 10⁶ seconds

T = 31,100 minutes

T = 518 hours

T = 21.6 days

T = 2 years

Therefore, the orbital period of the planet with twice the mass of Earth orbiting at a distance of 1 AU from a star with the same mass as the Sun is 2 years.

To know more about Kepler's third law of planetary motion:

https://brainly.com/question/4978861

#SPJ11

as noted in this chapter, plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality. soil erosion increases the silt load in water and this literally smothers living organisms, particularly plants and invertebrate species. runoff water can carry pollutants, particularly pesticides and herbicides from agricultural land. read the description of each landscape and rank them from best stream quality to worst stream quality. 1: streams cutting through small farms with several different crop types and natural vegetation buffers between the fields and the streams. 2: a large floodplain area covered with lowland forests and swamps full of emergent vegetation, with small streams cutting through the area. 3: an urban housing development where the trees growing along the streams were removed and replaced with lawns. 4: a system of large farms with no buffer vegetation between the fields and the streams that cut through the farms. question list (4 items) (drag and drop into the appropriate area) landscape 1 landscape 2 landscape 3 landscape 4 correct answer list best stream quality

Answers


Plants help to reduce water runoff and soil erosion, both of which affect the health of streams and rivers by impacting water quality.

Soil erosion increases the silt load in the water, which can smother living organisms, particularly plants and invertebrate species. Runoff water can carry pollutants, particularly pesticides, and herbicides from agricultural land.

Landscape 1 (streams cutting through small farms with a variety of crop types and natural vegetation buffers between the fields and the streams) would be the best quality, followed by Landscape 2 (a large floodplain area covered in lowland forests and swamps full of emergent vegetation, with small streams cutting through the area) and Landscape 3 (an urban housing development where the streams are surrounded by emergent vegetation).

Learn more about water quality at  brainly.com/question/20848502

#SPJ11

please help!!
If an object were in motion, how might you use a magnet to change the direction of its motion? Diagram the setup and explain your reasoning.​

Answers

If the object in motion has some magnetic properties or contains a magnet, we can use another magnet to change its direction of motion by exerting a force on it through magnetic interaction. This principle is known as the Lorentz force.

Here's how we can set up the experiment:

Take a magnet and place it on a flat surface.

Take another magnet or the object with magnetic properties that is in motion.

Hold the magnet or the object in your hand and bring it close to the stationary magnet without touching it.

Move the magnet or the object towards the stationary magnet and observe its behavior.

If the magnet or the object has the same polarity as the stationary magnet, they will repel each other, and the motion of the object will be deflected in a direction away from the stationary magnet. If the magnet or the object has opposite polarity to the stationary magnet, they will attract each other, and the motion of the object will be deflected in a direction towards the stationary magnet.

Here's a diagram to help you visualize the setup:

                 N   S          N   S

       __________    __________

      |                       |  |                     |

      |   M1               |  |           M2     |

      |__________|  |__________|

              ( )                             ( )

               |                               |

        Motion              Stationary

        Object                 Magnet

In this diagram, M1 represents the motion object or magnet, and M2 represents the stationary magnet. The N and S represent the North and South poles of the magnets. The arrows indicate the direction of motion and the direction of the magnetic field.

As we move M1 towards M2, the magnetic interaction will exert a force on M1, causing it to change its direction of motion. The direction of deflection will depend on the polarity of the magnets.

Note: It's important to keep in mind that the magnetic force is only one of the many factors that can affect the motion of an object. Other factors such as friction, air resistance, and gravitational forces can also play a significant role.

To know more about  Motion visit :-

https://brainly.com/question/453639

#SPJ1

Star A is identical to Star B, but Star A is twice as far from us as Star B. Therefore, _______________.

Answers

Star A's light will take longer to reach us.

The width of the cube was 18. 45 mm. The density of the cube was 8. 0 × 103 kg/m3

Calculate the mass of the cube

Answers

The required mass of the cube when width of the cube and density of the cube are specified is calculated to be 0.0502 kg.

The width of the cube is given as 18.45 mm = 18.45 × 10⁻³ m

The density of the cube is given as 8 × 10³ kg/m³.

Mass of the cube is to be found out.

The general formula for density of a cube is given by, V = s³

where,

V is volume

s is side/width/height (As they are all equal in a cube)

So, the volume of the cube is,

V = (18.45 × 10⁻³)³ = 0.01845³ = 6.28 × 10⁻⁶ m³

Now, we know the general equation for density as, mass upon unit volume.

Mathematically, D = m/V

Making m as subject, we have,

Mass m = D × V = 8 × 10³ × 6.28 × 10⁻⁶ = 50.24× 10⁻³ kg = 0.0502 kg

Thus, the required mass is calculated to be 0.0502 kg.

To know more about density:

https://brainly.com/question/952755

#SPJ4

an incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kpa. determine the change in enthalpy. multiple choice question. 0 kj/kg 0.9 kj/kg 10 kj/kg 900 kj/kg

Answers

The change in enthalpy of an incompressible substance with a density of 1000 kg/m³ that is isothermally compressed from 100 to 1000 kPa is 0 kJ/kg.

What is enthalpy?

Enthalpy is a measure of the total energy of a thermodynamic system. In addition, it incorporates the energy that is supplied to the system as heat, as well as any energy that is used as work. Enthalpy is represented by the symbol H and is usually calculated in units of joules (J).

What is an incompressible substance?

An incompressible substance is one that cannot be compressed or compressed to a significant degree. Liquids are examples of such materials. They are often described as having a constant density because, unlike gases, they do not easily change in volume in response to pressure or temperature changes. Therefore, the change in enthalpy is 0 kJ/kg.

Learn more about Enthalpy here: https://brainly.com/question/16985375.

#SPJ11

a ceiling fan is turned on and a net torque of 2.3 n*m applied to the blades. the blades have a total moment of inertia of 0.39 kg*m^2. what is the angular acceleration of the blades?

Answers

The angular acceleration of the blades  is 5.897 rad/s². It can be calculated using the formula α as the ratio of torque to moment of Inertia.

The torque is a rotational or twisting force. Angular acceleration is the rate at which the angular velocity of an object changes, measured in radians per second squared (rad/s²).

Given the torque and moment of inertia, we may utilize the following formula to find the angular acceleration of the blades:

[tex]\alpha= \dfrac{Torque}{Moment \; of \; inertia}\\\alpha= \dfrac{\tau}{I}[/tex]

where τ is the torque in newton-meters (N-m),I is the moment of inertia in kg-m², α is the angular acceleration in radians per second squared (rad/s²).

Rearranging the formula to solve for α gives:

[tex]\alpha=2.3/0.39\\=5.897 rad/s^2[/tex]

Therefore, the angular acceleration of the blades is 5.897 rad/s².

For further information about angular acceleration click on below link:

https://brainly.com/question/30238727

#SPJ11

If you stand on one foot while holding your other leg up behind you, your muscles apply a force to hold your leg in this raised position. We can model this situation as in Figure 1). The leg pivots at the knee joint, and the force that holds the leg up is provided by a tendon attached to the lower leg as shown Assume that the lower leg and the foot have a combined mass of 3.6kg, and that the combined center of gravity is at the center of Figure he knot What is the magnitude of this force? The london provides you hold your leg in this position the upper legeerts a force Express your answer with the appropriate units the lower le TARO? Value Units Sube

Answers

To keep the leg in the raised position, the tendon should provide 160N force.

The rotating force or moment of a force around a particular axis or pivot point is measured by torque. The tendency of a force to cause an object to spin along an axis is described as a vector quantity, torque.

Given: combined mass of the lower leg and the foot, m = 3.6kg

position of the center of gravity, r1 = 25cm

r = 0.25m

distance between tendon and lower leg, r2 = 5cm = 0.05m

torque applied will be τ = 3.6 × 10 × 0.25

τ = 8 N-m

the force applied by tendon

F = τ/ r2

F = 8/ 0.05

F = 160N

Therefore, To keep the leg in the raised position, the tendon should provide 160N force.

To know more about torque, click here:

https://brainly.com/question/29024338

#SPJ12

In a P-N-P transistor application, the solid state device is turned on when the
base is negative with respect to the emitter.
A P-N-P transistor conducts between the emitter and collector (is turned on) when a small amount of current flows into the base. This current flows when the emitter-base junction is forward biased. It is forward biased when the base is negative with respect to the emitter.

Answers

A P-N-P transistor is turned on when the base is negative with respect to the emitter.

How the transistor is turned on when the base is negative with respect to the emitter

The operation of a P-N-P transistor is based on the principle of a semiconductor diode. When a small current is applied to the base, it causes a larger current to flow through the emitter and collector. This is because the base-emitter junction is forward-biased, allowing electrons to flow from the emitter to the base. At the same time, the collector-base junction is reverse-biased, allowing holes to flow from the base to the collector.

This flow of electrons and holes produces a current gain. The amount of current gain depends on the type of transistor and the amount of current applied to the base.

Learn more about transistors here:

https://brainly.com/question/1426190

#SPJ1

true or false if the whole picture plane is affected by aerial diffusion, it stops being an effective indicator of depth.

Answers

If the whole picture plane is affected by aerial diffusion, it stops being an effective indicator of depth - this statement is true.

Aerial diffusion is the scattering of light by particles in the air. These particles cause distant objects to appear fainter and bluer than closer objects, leading to a decrease in visual clarity and the ability to perceive depth. Aerial diffusion can be utilized in painting and drawing to create an atmospheric perspective, which produces a sense of depth by making objects are that further away appear hazier and less distinct than those that are closer. However, if the entire picture plane is affected by aerial diffusion, this can make it difficult to distinguish between objects at different depths, which can result in a lack of clarity and depth perception in the painting or drawing.

A picture plane is a theoretical plane that corresponds to the surface of a painting or drawing. The picture plane is where the artist organizes and arranges the various elements of the composition to create a visual representation of a scene. The picture plane is where the viewer's eye interacts with the artwork, and where the illusion of depth and space is created. In this context, the picture plane is an important factor in the creation of depth and atmosphere in a painting or drawing.

Learn more about aerial diffusion:

https://brainly.com/question/1381101

#SPJ11

A converging lens of focal length 20cm Forms a real Image of 4cm high of an object which is 5cm high. If the Image is 36cm away from the lens, determine by graphical method the position of the object.​

Answers

Answer:

in image

Explanation:

I don't think so it helped but through this you can do the question exactly like this ( in this way) ...

An apple fell 6.0 m from a tree to the ground. What additional information is needed to calculate both the gravitational potential energy of the apple and its kinetic energy?

the volume of the apple and the time the apple was in the air
the mass of the apple and the amount of energy lost to air resistance
the average acceleration of the apple and the time the apple was in the air
the average velocity of the apple and the amount of energy lost to friction

Answers

For calculation of potential energy mass of the apple , average acceleration of the apple and height of apple is required.

Energy While for calculation of kinetic energy volume of the apple and time the apple was in air, the average velocity of the apple and amount of energy lost to friction is required.Based on the force exerted on the two objects, the potential energy equation is determined. P.E. = mgh, where m is the mass in kilograms, g is the acceleration caused by gravity (9.8 m/s2 at the earth's surface), and h is the height in meters, is the formula for gravitational force.The relationship between kinetic energy and an object's mass and squared velocity is given by K.E. = 1/2 m v2. If the mass is measured in kilograms and the speed is measured in meters per second, the kinetic energy is measured in kilogram-meters squared per second squared.

For more information on kinetic and potential energy kindly visit to

https://brainly.com/question/11749818

#SPJ1

The position of a toy locomotive moving on a straight track along the x axis is given by the equation x = t^3 - 6t^2 + 9t, where x is in meters and t is in seconds. The net force on the locomotive is equal to zero when t is equal to (A) zero (B) 2 s (C) 3 s (D) 4 s (E) 5 s

Answers

Option C, The net force on the toy locomotive moving on a straight track along the x-axis is equal to zero at t=3s.

A force is any push or pull that results in a modification in the state of motion of an object. The net force on an object is the combination of all forces acting on it in a specific direction. An object in motion will continue to move in a straight line at a steady velocity unless acted upon by a net force, according to Newton's first law of motion. The equation of motion for the toy locomotive is as follows:

x = t³ - 6t² + 9t

We must differentiate this equation twice to determine the acceleration of the toy locomotive.

a = x′′= 6t - 12, At time t = 3 seconds, the net force on the toy locomotive is zero. This occurs when the acceleration of the toy locomotive equals zero.

6t - 12 = 0t = 2

Therefore, the net force on the toy locomotive moving on a straight track along the x-axis is equal to zero at t = 3 seconds.

Learn more about force and locomotive at : https://brainly.com/question/14206785

#SPJ11

a proton accelerates from rest in a uniform electric field of 600 n/c. at one later moment, its speed is 1.50 mm/s (nonrelativistic because v is much less than the speed of light). find the time interval, in ms, that the proton takes to reach this speed. flag question: question 11

Answers

The proton accelerates from rest in a uniform electric field of 600 n/c. In order to find the time interval it takes for the proton to reach a speed of 1.50 mm/s.

We need to use the equation v = v₀ + at, where v is the final velocity, v₀ is the initial velocity (which is 0 in this case), a is the acceleration, and t is the time interval. The acceleration of the proton in the electric field is a = E/m, where E is the electric field and m is the mass of the proton. Substituting these values into the equation gives us:

1.50 mm/s = 0 + (600 n/c/1.67 x 10⁻²⁷ kg) x t

Rearranging the equation and solving for t gives us the time interval:
t = 1.50 mm/s/(600 n/c/1.67 x 10⁻²⁷ kg)

t = 8.33 x 10⁻¹³ s

t = 8.33 ms

Therefore, it takes the proton 8.33 ms to accelerate from rest to a speed of 1.50 mm/s in the uniform electric field of 600 n/c.

Learn more about proton accelerates at https://brainly.com/question/21595065

#SPJ11

Find the angle ϕ between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value. Express your answer in degrees to four significant figures

Answers

"The required angle Ф between the filter's polarizing axis and the direction of polarization of light necessary to increase the ratio of the clouds' intensity to that of the blue sky so that it is three times the normal value is 65.9°."

A photographer wants to click a picture of a cloud formation, the ratio of clouds intensity to that of the blue sky photographer uses polarizing filter from Malus law,

I = I₀ cos²Ф

So, I f = I i cos²Ф

As the light from cloud is polarized, its intensity reduces to half.

I c = I₀/2

The intensity of light from sky is polarized light.

I s = I₀ cos²Ф

Hence, the ratio of intensities is,

I c/I s = (I₀/2)/(I₀ cos²Ф)

3 = (I₀/2)/(I₀ cos²Ф)

cos²Ф = 1/6

Thus, the required angle is Ф = cos⁻¹(1/√6) = 65.9°

To know more about angles:

https://brainly.com/question/28562350

#SPJ4

a rectangular field is twice as long as it is wide. the perimeter of the field is 450 yards. find the dimensions of the field. you must find an equation to represent the situation and solve.

Answers

The dimensions of the field can be found to be 75 yards in width and 150 yards in length.

Given:
Let the width of the rectangular field be x
Length of the rectangular field = 2x
Perimeter of the rectangular field = 450 yards


Formula Used:
Perimeter of a rectangle = 2 (l + w)

Where l and w are the length and width of the rectangle respectively.

Solution:
As per the question,
Perimeter of the rectangular field = 450 yards


Therefore, 2(Length + Width) = 450
2(x + 2x) = 450
2(3x) = 450
6x = 450
x = 75
Therefore, the width of the rectangular field is 75 yards
Length of the rectangular field = 2x = 2 × 75 = 150 yards

Hence, the dimensions of the field are 75 yards by 150 yards.

To know more perimeter, refer here:

https://brainly.com/question/30252651#

#SPJ11

given what you learned from the figure, rank these types of light in order of increasing energy. 1. radio 2. infrared 3. orange 4. green 5. ultraviolet

Answers

Answer:

✓ 1. radio 2. infrared 3. orange 4. green 5. ultraviolet

Explanation:

Why are masses listed on the periodic table not whole #'s. Ex. 15.9999 for oxygen?​

Answers

The masses listed on the periodic table are not whole numbers because they represent the weighted average of all the naturally occurring isotopes of an element.

What are Isotopes ?

Isotopes are atoms of the same element that have different numbers of neutrons in their nuclei, resulting in slightly different masses. Since the abundance of each isotope in nature can vary, the weighted average takes into account the abundance of each isotope and their corresponding masses, resulting in a decimal value. For example, oxygen has three naturally occurring isotopes, with mass numbers of 16, 17, and 18.

Why only O-16 isotopes ?

The most abundant isotope is oxygen-16, but the other isotopes are also present in trace amounts, leading to a weighted average of 15.9994 amu (atomic mass units). This is why the mass listed on the periodic table for oxygen is 15.999, which is a rounded value of the weighted average.

To know more about isotopes , visit :

https://brainly.com/question/11680817

#SPJ1

The masses listed on the periodic table are not whole numbers because they represent the average atomic mass of all the naturally occurring isotopes of an element, taking into account their relative abundances.

What are isotopes ?

Isotopes are atoms of the same element that have different numbers of neutrons in their nucleus, which affects their atomic mass. Some isotopes of an element are more abundant than others, and their relative abundances are taken into account when calculating the average atomic mass.

For example, oxygen has three naturally occurring isotopes: oxygen-16, oxygen-17, and oxygen-18. Oxygen-16 is the most abundant isotope, making up about 99% of all oxygen atoms. Oxygen-17 and oxygen-18 are much less abundant, but they still contribute to the overall atomic mass of the element.

The atomic mass listed on the periodic table for oxygen (15.9994) is the weighted average of the atomic masses of all three isotopes, taking into account their relative abundances. This average is not a whole number because the isotopes have different atomic masses and abundances, and their contributions to the overall average are weighted accordingly.

To know more about Periodic table visit :-

https://brainly.com/question/1173237

#SPJ1

Suppose you watch a leaf bobbing up and down as ripples pass it by in a pond. You notice that it does two full up and down bobs each second. Which statement is true of the ripples on the pond?
They have a frequency of 2 hertz.

Answers

The correct statement of the ripples on the pond is that they have a frequency of 2 hertz.

In physics, the number of cycles of a periodic wave that occur in a unit of time is known as the frequency of that wave. Its unit is hertz (Hz), which indicates cycles per second.A hertz is a unit of frequency that indicates how many times per second a wave oscillates. The amount of time it takes for one complete cycle of the wave is inversely proportional to its frequency. A wave with a high frequency oscillates more frequently than one with a low frequency.What is hertz (Hz)?Hertz (Hz) is the standard unit of frequency. One hertz (Hz) is equal to one cycle per second, meaning that a wave with a frequency of 2 Hz repeats twice in one second. Therefore, the frequency of the ripples on the pond is 2 hertz.

More on frequency: https://brainly.com/question/25811461

#SPJ11

An electroscope is a device with a metal knob, a metal stem, and freely hanging metal leaves used to detect charges. The diagram below shows a positively charged leaf electroscope.
As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will
remain the same
increase

Answers

As a positively charged glass rod is brought near the knob of the electroscope, the separation of the leaves will increase.

What is Charge?

Charge is a fundamental property of matter that determines how objects interact with each other through the electromagnetic force. It is a physical property that can be positive or negative and can be measured in coulombs (C).

This is because the positively charged glass rod will induce a negative charge on the metal knob of the electroscope. The negative charges will repel the electrons in the metal leaves, causing them to move away from each other and increasing their separation. The greater the amount of charge on the glass rod, the greater the separation between the leaves will be.

Learn more about Charge from given link

https://brainly.com/question/18102056

#SPJ1

A 1500 kg car is moving to the right with a speed of 20.0 m/s when it collides with a wall and reboubds at a speed of 5.00 m/s.

If the collision lasts for 250 ms, then the magnitude of the average force acring on the car is _____ kN (the answer is 150 but I'm not sure how)
pls help!! ​

Answers

Answer:

See below.

Explanation:

When the 1500 kg car collides with the wall and rebounds at a speed of 5.00 m/s, we can calculate the change in the car's velocity using the following formula:

Δv = v2 - v1

Where Δv is the change in velocity, v2 is the final velocity, and v1 is the initial velocity. Substituting the given values, we get:

Δv = 5.00 m/s - 20.0 m/s

Δv = -15.0 m/s

The negative sign indicates that the direction of the car's velocity has reversed, or that the car is now moving to the left. To calculate the magnitude of the change in velocity, we take the absolute value:

|Δv| = |-15.0 m/s|

|Δv| = 15.0 m/s

Therefore, the magnitude of the change in velocity is 15.0 m/s.

Now,

To find the magnitude of the average force acting on the car during the collision, we can use the impulse-momentum theorem, which states that:

Impulse = change in momentum

Average force = Impulse / time

The change in momentum of the car is given by:

Δp = mΔv

where Δv is the change in velocity calculated in the previous answer and m is the mass of the car.

Δp = 1500 kg × (-15.0 m/s)

Δp = -22500 kg·m/s

The impulse acting on the car during the collision is equal to the change in momentum:

Impulse = Δp = -22500 kg·m/s

To find the magnitude of the average force acting on the car during the 250 ms collision, we divide the impulse by the duration of the collision:

Average force = Impulse / time

Average force = -22500 kg·m/s / 0.250 s

Average force ≈ -90,000 N

The negative sign indicates that the force is in the opposite direction of the car's motion, or to the left. Therefore, the magnitude of the average force acting on the car during the collision is approximately 90,000 N.

Other Questions
Produce a list of all customers who live in the state of Florida and have ordered books about computers.a)SELECT DISTINCT c.lastname, c.customer#FROM books b, orders o, orderitems i, customers cWHERE c.customer# = o.customer#AND o.order# = i.order#AND i.isbn = b.isbnAND c.state = 'FL'AND b.category = 'COMPUTER';b)SELECT DISTINCT c.lastname, customer#FROM books b JOIN orderitems USING (isbn)JOIN orders USING (order#)JOIN customers c USING (customer#)WHERE c.state = 'FL'AND b.category = 'COMPUTER'; Which of the following activities would violate a provision of the NPA and Board Rule 217.11(2), Standards of Nursing Practice, relating to the practice of nursing by a LVN? A. Assisting in the evaluation of a client's response to nursing interventions. B. Practicing in any setting without an appropriate practice supervisor who is at least telephonically available. C. Collaborating with the RN to revise the nursing care plans for assigned clients. D. Making assignments to other licensed nurses and to unlicensed assistive personnel when working in a supervisory position. A crane lifts an object weighing 25000N up with a constant speed of 0.8m/s. calculate the capacity of that crane Classify the compounds as a strong acid, weak acid, strong base, or weak base.Strong acid ______Weak acid ______Strong base ______Weak base ______Aswer Bank : HI, HCN, NH3, Sr(OH)2, H2S03, H2S04, LiOH What part of the temporal bone does the mandible articulate with what is the name of this joint? Jose and his children went into a grocery store where they sell apples for $2.25 each and mangos for $1.25 each. Jose has $20 to spend and must buy at least 9 apples and mangos altogether. Also, he must buy at least 3 apples and at most 9 mangos. If x represents the number of apples purchased and y represents the number of mangos purchased, write and solve a system of inequalities graphically and determine one possible solution. When household debt levels rise:a. the ability to get more credit rises.b. families are less able to spend in the current period.c. investment levels rise.d. tax payments will be higher.e. none of the above juveniles who exhibit characteristics similar to antisocial personality disorder are diagnosed with conduct disorder. The peptide portion of any protein without its prosthetic group is called ______. A. Apoprotein B. Preprotein C. Holoprotein D. Euprotein The mean height of 15 pupils is 159 cm. One of these pupils is 148 cm and leaves the group. Determine the new mean height of the group. Give your answer correct to 1 decimal place. Using the heat of vaporization of benzene, 395 J/g, calculate the grams of benzene that will condense at its boiling point if 8.44 kJ is removed. Actors who have played Hannibal Lecter, Bane, Freddie and Jason have had to convey emotional intensity and attitude while contending with the following:Group of answer choicesdemanding directorscomplicated scriptsfacial appliancesdifficult vocal patterns how does the cybersecurity goal of preserving data integrity relate to the goal of authenticating users? 9. After taking a bath, Myra used her cotton towel in dying her hair and body. The towelabsorbed the water and make them dry easily. Which of the following statement istrue?A. Cotton towel is not an example of porous material.B. The softness of the towel made her hair and body dry.C. Some materials such as towels cannot absorb liquid enough.D. The towel is a porous material that has plenty of spaces inside thatabsorbs liquid. Which of the following BEST describes horizontal integration?the economic development of flatlands in the American westa company owns all the businesses that supply it with raw goods and necessary serviceswhen the government lets businesses operate without restrictionsa company acquires similar competing businesses and merges them into a single entity The ___ test for estimating vo2 max is based on the principle that your heart rate returns to resting levels after exercise faster when you have a higher level of cardiorespiratory fitness.1.5 mile runstep cycle ergometer1-mile walk use the newton-raphson method to find an approximate value of 37 . use the method until successive approximations obtained by calculator are identical. an appropriate function to use for the approximation would be f (x) = A x^2 + B x^3 + C x + D where A= B= C= D=If c1 = 2, then c2 = ___23= ____ The Stamp-M-Out Company manufactures rubber stamps. An inspector finds that there are 10 defective stamps in a sample of 700. a) What is the probability that a randomly selected stamp will be defective?b) According to Stamp-M-Out Company quality control standards no more than 3.5% of stamps produced may be defective. Does Stamp-M-Out Company need to adjust its manufacturing process to meet this standard? Which of the following methodologies can help you assess gender issues relevant to nutrition? _____ are found in literature and provide a general explanation as to what the researcher hopes to find in a study or a lens through which to view the needs of participants and communities in a study.a. Theoriesb. Theoretical Orientationc. Frameworkd. Both a and b