A 5.0 Ω resistor is hooked up in series with a 10.0 Ω resistor followed by a 20.0 Ω resistor. The circuit is powered by a 9.0 V battery. Draw a labeled circuit diagram for the circuit described using correct symbols. Calculate the equivalent resistance. Calculate the voltage drop across each resistor in the circuit.
Answers
(a) Attached to the response as Figure 1.
(b) 35.0Ω
(c) Across 5.0Ω = 1.3V
Across 10.0Ω = 2.6Ω
Across 20.0Ω = 5.2Ω
Explanation:(a) The labelled circuit using the correct symbols (for the resistors and battery) has been attached to this response.
(b) Since the resistors are hooked up in series, their equivalent resistance R, is found by adding the individual resistances of the resistors (R₁, R₂ and R₃). i.e
R = R₁ + R₂ + R₃ -------------------(i)
Where;
R₁ = 5.0 Ω
R₂ = 10.0 Ω
R₃ = 20.0 Ω
Substitute these values into equation (i) as follows;
∴ R = 5.0 Ω + 10.0 Ω + 20.0 Ω
∴ R = 35.0 Ω
Therefore, the equivalent resistance is ∴ R = 35.0Ω
(c) When resistors are connected in series, the same current passes through them. To get the current through each resistor;
i. First, replace the resistors by their equivalent resistor as calculated above. The diagram has been attached to this response.
ii. As seen in the diagram, the current flowing through the equivalent resistor can be calculated using Ohm's law as follows;
V = I R ------------------(ii)
Where;
V = Voltage supplied to the circuit = 9.0V
I = Current through the circuit
R = Resistance of the equivalent resistor = 35.0Ω
Substitute these values into equation (ii)
9.0 = I x 35.0
I = [tex]\frac{9.0}{35.0}[/tex]
I = 0.26A
This is also the current flowing through each of the resistors separately.
iii. Calculate the voltage drop across
1. 5.0 Ω resistor
Applying Ohm's law from equation (ii)
V = I x R
Where;
V = voltage drop across the 5.0Ω resistor
I = current through the 5.0Ω resistor = 0.26A
R = resistance of the 5.0Ω resistor = 5.0Ω
=> V = 0.26 x 5.0
=> V = 1.3V
2. 10.0 Ω resistor
Applying Ohm's law from equation (ii)
V = I x R
Where;
V = voltage drop across the 10.0Ω resistor
I = current through the 10.0Ω resistor = 0.26A
R = resistance of the 10.0Ω resistor = 10.0Ω
=> V = 0.26 x 10.0
=> V = 2.6V
3. 20.0 Ω resistor
Applying Ohm's law from equation (ii)
V = I x R
Where;
V = voltage drop across the 20.0Ω resistor
I = current through the 20.0Ω resistor = 0.26A
R = resistance of the 20.0Ω resistor = 10.0Ω
=> V = 0.26 x 20.0
=> V = 5.2V
Related Questions
E=kq/r^2 chứng minh điện thế V=kq/r từ mối liên hệ giữa điện trường E và điện thế V
Answers
Answer:
hindi ko maintindihan teh
If you are driving a car with a velocity of -25 m/s and you have an acceleration of -2 m/s^2, are you speeding up or slowing down? Why?
Answers
Answer:
Hmmm...
This is a bit tricky
Ok...
Negative Velocity means you're Moving in the Opposite direction....
Negative Acceleration (deceleration) means you're slowing down.
Deceleration would mean slowing down if you were Moving with a Positive velocity.
But In this case...
You're Moving with negative velocity and Negative acceleration...
This simply means that the acceleration and velocity vector are in the same direction....
Its means that...
"YOU'RE SPEEDING UP"
Just that you're doing it in the opposite direction.
Hope this helps.
7. An electric train moving at 20km/hrs
. Accelerates to a speed of 30km/hrs. in
20 sec, find the distance travelled in meters during the period of
acceleration
Answers
Answer
NB:
- speed, U is measure in m/s
- acceleration, a is measured in m/s²
-time t in seconds , s
Therefore conversation must be made
Speed U = 20km/hrs
=20km÷1hr
But 20km= 20×1000=20000m
1hr= 1×60min×60sec=3600s
U=20000÷3600=5.56m/s
a=30km/hrs
=30km÷1hr
But 30km=30×1000=30000
1hr=3600s
a=30000÷3600=8.33m/s²
From the equation of motion
S=Ut + ½ at².
Where s= distance
S = 5.56m/s × 20s + ½(8.33m/s²)(20s)²
S = 1777.3m
nariz (am
miria amy
0 = 0 +260 + (0)
U= 29 mb
6= ut +1 (04)
Car I was sitting at rest when it nous hit from
the rear by car 2 of identical mass. Both cant had
their heaks on and they stidled together Guy
in the original directioned of motion. If the stopping
force is notx (Combined weight of the cars), die
u=0 to find the approximate speed of car a just
before the collision took place on
Answers
Answer:
33 mph
Explanation:
My best guess
Transfer of thermal energy between air molecules in closed room is an example of
conduction
convection
radiation
Answer and I will give you brainiliest
Answers
Answer: Conduction
Explanation: Conduction is the process by which heat energy is transmitted through collisions between neighboring atoms or molecules. Conduction occurs more readily in solids and liquids, where the particles are closer to together, than in gases, where particles are further apart.
Are you aware of human rights violation happening in the community and explain
Answers
Answer:
Individuals who commit serious violations of international human rights or humanitarian law, including crimes against humanity and war crimes, may be prosecuted by their own country or by other countries exercising what is known as “universal jurisdiction.”
5. Tests performed on a 16.0 cm strip of the donated aorta reveal that it stretches 3.37 cm when a 1.80 N pull is exerted on it. (a) What is the force constant of this strip of aortal material
Answers
Answer:
53.41 N/m
Explanation:
From Hooke's law,
Applying,
F = ke............. Equation 1
Where F = Force, e = extension, k = force constant of the aortal material
Make k the subject of the equation
k = F/e............. Equation 2
From the question,
Given: F = 1.8 N, e = 3.37 cm = 0.0337 m
Substitute these values into equation 2
k = 1.8/(0.0337)
k = 53.41 N/m
Hence the force constant of the aortal material is 53.41 N/m
One way families influence healthy technology use is when siblings explain the use of media to each other. Which of these outfits would you expect if this guideline was followed?
Answers
Answer:
The answer would be C.
Explanation:
This is what I would expect when you show someone else how to do something then is also known as teaching.
Please Mark as Brainliest
Hope this Helps
help asap PLEASE I will give u max everything all that
steps if possible
Answers
Explanation:
2. [tex]R_T = R_1 + R_2 + R_3 = 625\:Ω + 330\:Ω + 1500\:Ω[/tex]
[tex]\:\:\:\:\:\:\:= 2455\:Ω = 2.455\:kΩ[/tex]
3. Resistors in series only need to be added together so
[tex]R_T = 8(140\:Ω) = 1120\:Ω = 1.12\:kΩ[/tex]
A rocket at fired straight up from rest with a net upward acceleration of 20 m/s2 starting from the ground. After 4.0 s, the thrusters fail and the rocket continues to coast upward with insignificant air resistance. (a) What is the maximum height reached by the rocket
Answers
Answer:
The maximum height reached by the rocket is 486.53 m
Explanation:
Given;
initial velocity of the rocket, u = 0
acceleration of the rocket, a= 20 m/s²
duration of the rocket first motion, t = 4 s
The distance traveled by the rocket before its thrust failed
h₁ = ut + ¹/₂at²
h₁ = 0 + ¹/₂ x 20 x 4²
h₁ = 160 m
The second distance moved by the rocket is calculated as follows;
The velocity of the rocket before its thrust failed;
v = u + at
v = 0 + 20 x 4
v = 80 m/s
This becomes the initial velocity for the second stage
At maximum height, the final velocity = 0
[tex]v_f^0 = v_i^2 - 2gh_2\\\\0 = (80)^2 - (2 \times 9.8)h_2\\\\0 = 6400 - 19.6h_2\\\\19.6h_2 = 6400\\\\h_2 = \frac{6400}{19.6} \\\\h_2 = 326.53 \ m[/tex]
The maximum height reached by the rocket = h₁ + h₂
= 160 + 326.53
= 486.53 m
steps btw if possible
asap pls I will give u everyting
Answers
Answer:
(4) 50 ohms (5) 11.76 ohms
Explanation:
In the parallel combination, the equivalent resistance is given by :
[tex]\dfrac{1}{R}=\dfrac{1}{R_1}+\dfrac{1}{R_2}+....[/tex]
4. When three 150 ohms resistors are connected in parallel, the equivalent is given by :
[tex]\dfrac{1}{R}=\dfrac{1}{150}+\dfrac{1}{150}+\dfrac{1}{150}\\\\R=50\ \Omega[/tex]
5. Three resistors of 20 ohms, 40 ohms and 100 ohms are connected in parallel, So,
[tex]\dfrac{1}{R}=\dfrac{1}{20}+\dfrac{1}{40}+\dfrac{1}{100}\\\\=11.76\ \Omega[/tex]
Hence, this is the required solution.
A rock is pulled back in a slingshot as shown in the diagram below. The elastic on the slingshot is displaced 0.2 meters from its initial position. The rock is pulled back with a force of 10 newtons.
When the rock is released, what is its kinetic energy?
Answers
Answer:
id
Explanation:
i don't know
The rock takes 8.16s to return to its release point. Given that the elastic band provides a speed of 40m/s to the rock in 10 cm stretch.
What will be the speed of the rock?Initial speed of the rock, u = 40m/s
Final position of the rock s = 0m taking the release point as reference. The rock takes 8.16s to return to its release point. Given that the elastic band provides a speed of 40m/s to the rock in 10 cm stretch.
Nuclear energy is a useful source of power but has disadvantages. The disadvantage of nuclear energy is it produces dangerous waste.
Initial speed of the rock, u = 40m/s
Final position of the rock s = 0m taking the release point as reference
From the second equation of motion:
solving above we get:
t = 0s or t = 8.16s, t =0 seconds is neglected since it represents the initial position which is the same as the final position at t = 8.16s
So, the rock takes 8.16 seconds to return to the release point.
Therefore, The rock takes 8.16s to return to its release point. Given that the elastic band provides a speed of 40m/s to the rock in 10 cm stretch.
Learn more about speed of rock on:
brainly.com/question/11049671
#SPJ2
Please help I need this done
Answers
why material selection is important to design and manufacturing?
Answers
Answer:
. You want your product to be as strong and as long lasting as possible. There are also the safety implications to consider. You see, dangerous failures arising from poor material selection are still an all too common occurrence in many industries. yep that the answer have a Great day
Explanation:
(◕ᴗ◕✿)
Hai điện tích điểm Q1 = 8 C, Q2 = –6
C đặt tại hai điểm A, B cách nhau 0,1
m trong không khí. Tính cường độ điện
trường do hai điện tích này gây ra tại
điểm M, biết MA = 0,2 m
Answers
Answer:
English please
Explanation:
I don't understand the question
Two children stretch a jump rope between them and send wave pulses back and forth on it. The rope is 3.3 m long, its mass is 0.52 kg, and the force exerted on it by the children is 47 N. (a) What is the linear mass density of the rope (in kg/m)
Answers
Answer:
The linear mass density of rope is 0.16 kg/m.
Explanation:
mass, m = 0.52 kg
force, F = 47 N
length, L = 3.3 m
(a) The linear mass density of the rope is defined as the mass of the rope per unit length.
Linear mass density = m/L = 0.52/3.3 = 0.16 kg/m
c) You wish to put a 1000-kg satellite into a circular orbit 300 km above the earth's surface. (a)
What speed, period, and radial acceleration will it have? (b) How much work must be done to the
satellite to put it in orbit? (c) How much additional work would have to be done to make the
Answers
Answer:
Scalar
Explanation:
No direction
If you drive first at 40 km/h west and later at 60 km/h west, your average velocity is 50 km/h west.
Answers
and what else? is that all?
plz answer the question
Answers
Answer:
Ray A = Incidence ray
Ray B = Reflected ray
Explanation:
From the law of reflection,
Normal: This is the line that makes an angle of 90° with the reflecting surface.
Ray A is the incidence ray: This is the ray that srikes the surface of a reflecting surface. The angle formed between the normal and the incidence ray is called the incidence angle
Ray B is the reflected ray: This is the ray leaves the surface of a reflecting surface. The angle formed between the reflected ray and the normal is called reflected angle
Copy the diagram. add a voltmeter to show how you would measure the voltage of the cell
Answers
Answer: the answer is 23voltage
Explanation: because the voltage and time put together is 23
A cement block accidentally falls from rest from the ledge of a 53.4-m-high building. When the block is 19.4 m above the ground, a man, 2.00 m tall, looks up and notices that the block is directly above him. How much time, at most, does the man have to get out of the way
Answers
Answer:
The time required by the man to get out of the way is 0.6 s.
Explanation:
height of building, H = 53.4 m
height of block, h = 19.4 m
height of man, h' = 2 m
Let the velocity of the block at 19.4 m is v.
use third equation of motion
[tex]v^2 = u^2 + 2 gh\\\\v^2 = 0 + 2 \times 9.8 \times (53.4 - 19.4)\\\\v = 25.8 m/s[/tex]
Now let the time is t.
Use second equation of motion
[tex]h = u t + 0.5 gt^2\\\\19.4 - 2 = 25.8 t + 4.9 t^2\\\\4.9 t^2 + 25.8 t - 17.4= 0 \\\\t = \frac{-25.8\pm\sqrt{665.64 + 341.04}}{9.8}\\\\t = \frac{-25.8\pm31.7}{9.8}\\\\t = 0.6 s, - 5.9 s[/tex]
Time cannot be negative so time t = 0.6 s.
A large dump truck can move 1,170 tons/h of gravel from one point to another on a work site. What is this rate in lb/s
Answers
Answer:
The rate of the dump truck is 650 [tex]\frac{lb}{s}[/tex]
Explanation:
A large dump truck can move 1,170 tons/h of gravel from one point to another on a work site.
To convert the units from tons/h to lb/s, you should know that:
1 ton= 2000 lb1 h= 3600 s (1 h= 60 minutes and 1 minute= 60 seconds)To carry out the unit conversion you must perform the following steps:
[tex]1170 \frac{ton}{h}*\frac{2000 lb}{1 ton} *\frac{1 h}{3600 s}[/tex]
Solving:
[tex]1170 \frac{ton}{h}*=650 \frac{lb}{s}[/tex]
So, the rate of the dump truck is 650 [tex]\frac{lb}{s}[/tex]
Its volume is 20 cm3, and its mass is 100 grams. What is the sample’s density?
Answers
100/20 = 5
The density is 5
The wave functions for states of the hydrogen atom with orbital quantum number l=0 are much simpler than for most other states, because the angular part of the wave.
a. True
b. False
Answers
When two bodies at different temperatures are placed in thermal contact with each other, heat flows from the body at higher temperature to the body at lower temperature until them both acquire the same temperature. Assuming that there is no loss of heat to the surroundings, the heatSingle choice.
(1 Point)
(a) gained by the hotter body will be equal to the heat lost by the colder body
(b) the heat gained by the hotter body will be less than the heat lost by the colder body
(c) the heat gained by the hotter body will be greater than the heat lost by the colder body
(d) the heat lost by the hotter body will be equal to the heat gained by the colder body.
Answers
Answer:
Part d is correct.
Pete is investigating the solubility of salt (NaCl) in water. He begins to add 50 grams of salt to 100 grams of
room temperature tap water in a beaker. After adding all of the salt and stirring for several minutes, Pete
notices a solid substance in the bottom of the beaker. Which statement best explains why there is a solid
substance in the bottom of the beaker?
A. The salt he is using is not soluble in water.
B. The salt is changing into a new substance that is not soluble in water,
C. The dissolving salt is causing impurities in the water to precipitate to the bottom
D. The water is saturated and the remaining salt precipitates to the bottom
Answers
Answer:
would the answer be c
Explanation: that what i think in my opian
Answer:
A
Explanation:
The speed of a 2.0-kg object changes from 30 m/s to 40 m/s during a 5.0-second time interval.
During this same time interval, the velocity of the object changes its direction by 90°. What is the
magnitude of the average total force acting on the object during this time interval?
a. 30 N
b. 20 N
c. 15 N
d. 40 N
e. 10 N
Which is the correct answer?
Answers
Answer:
F = 2 * 30 / 5 = 12 N to stop forward motion
F = 2 * 40 / 5 = 16 N to accelerate to 90 degrees
(12^2 + 16^2)^1.2 = 20 N average force applied
The magnitude of the average total force acting on the object during this time interval is 20 N.
The given parameters:
Mass of the object, m = 2.0 kgInitial velocity, u = 30 m/sFinal velocity, v = 40 m/sTime of motion, t = 5.0 sThe magnitude of the average total force acting on the object during this time interval is calculated as follows;
[tex]F = \frac{mv }{t} \\\\F_1 = \frac{2(40)}{5} \\\\F_1 = 16\ N\\\\F_2= \frac{2(30)}{5} \\\\F_2 = 12 \ N\\\\F = \sqrt{F_1^2 + F_2^2} \\\\F = \sqrt{16^2 + 12^2} \\\\F = 20 \ N[/tex]
Learn more about resultant force here: https://brainly.com/question/25239010
Calculate the rms speed of helium atoms near the surface of the Sun at a temperature of about 5100 K. Express your answer to two significant figures and include the appropriate units.
Answers
Answer:
[tex]V_{rms}=5.6*10^3m/s[/tex]
Explanation:
From the question we are told that:
Temperature [tex]T=5100K[/tex]
Generally the equation for RMS Speed is mathematically given by
[tex]V_{rms}=\sqrt{\frac{3kT}{m}}[/tex]
Where
[tex]K=Boltzman's constant[/tex]
[tex]K=1.38*10^{-23}[/tex]
And
[tex]M=molecular mass[/tex]
[tex]M=4*1.67*10^{-27}[/tex]
[tex]V_{rms}=\sqrt{\frac{3(1.38*10^{-23})5100}{4*1.67*10^{-27}}}[/tex]
[tex]V_{rms}=5.6*10^3m/s[/tex]
An amusement park ride whisks you vertically upward. You travel at a constant speed of 15 m/s during the entire ascent. You drop your phone 4.0 s after you (and your phone) begin your ascent from ground level.
a. How high above the ground is your phone when you drop it?
b. Find the maximum height above the ground reached by your phone.
Answers
Answer:
a. 60 m
b. 71.48 m
Explanation:
Below are the calculations:
a. The phone's height above the ground = Speed x Time
The phone's height above the ground = 15 x 4 = 60 m
b. Speed when phone drops, u = 15 m/s
At maximum height, v = 0
Use below formula:
v² = u² -2gh
0 = 15² + 2 × 9.8 × h
h = 11.48 m
Total height = 60 + 11.48 = 71.48 m
Kaseem is taking his bicycle for a ride. His bicycle is a system, and its main purpose is to provide transportation. What is the main input into this system? What is the desired output of this system?
