1 point
40 The diagram below shows an electrical circuit made up of a cell and three loads. The
voltage established by the cell and the resistance of each load is marked on the
diagram. Select the current flowing through the 3-ohm load.
www
1 ohm
12V
2 ohms
WWW
3 ohms
www
A. 4 amps
B. 2 amps
C. 5 amps
D. 0.25 amps
SPS106 DOK 3

Answer:

F = 9.675Hz

Explanation:

pls for certain reasons let us make

3 loops : 6$/4 = L

6$/4 = 2

$ = 4/3 = 1.333

V = F x $

F = V/$

F = 12.9/1.333 = 9.675Hz

F = 9.675Hz

Answer:

161,000 cm

Explanation:

1 mi × (1.61 km/mi) × (1000 m/km) × (100 cm/m) = 161,000 cm

Answer:

Wavelength = 1 meters

Explanation:

Given that,

Number of oscillations is 5

It passes through a point in 0.5 s

The speed of sound was recorded to be 10 m/s.

We need to find the wavelength of the sound.

Firstly, we will find frequency of this wave. Total no of oscillations per unit time is called frequency. So,

[tex]f=\dfrac{5}{0.5}\\\\f=10\ Hz[/tex]

Now the speed of wave in terms of wavelength and frequency is given by :

[tex]v=f\lambda[/tex]

Here, [tex]\lambda[/tex] = wavelength

[tex]\lambda=\dfrac{v}{f}\\\\\lambda=\dfrac{10\ m/s}{10\ Hz}\\\\\lambda=1\ m[/tex]

So, the wavelength of the sound is 1 meters.

In a food web, the removal of any trophic level upsets the balance within the web and can cause its eventual collapse. Because producers capture solar energy and convert it to food energy, their loss would affect every other level of the food web.

The removal of the producers would cause the collapse of the entire food web. Primary consumers or herbivores, which feed on producers directly, would die off. The next to be affected would be the secondary consumers or carnivores that eat the primary consumers. Higher level consumers would suffer as organisms from lower trophic levels start to die off. Decomposers would break down the bodies of dead organisms, returning their basic elements and compounds to the environment. However, even these dead organisms would run out and the entire food web would collapse.

Hope you like the answer.

Explanation:

Some Uses of Electromagnetic waves :

(A) Microwaves

(B) X - Rays (produced by slowing fast moving electrons)

(C) Radio Waves

Explanation:

Hi, there!!

Energy is defined as the capacity or ability to do work. It's SI unit is Joule.

here,

Joule = (kg×m×m)/(s×s)

= kg×m^2/s^2.

Therefore, the derived unit is kg.m^2 by s^2.

Hope it helps...

Answer:

Cows,Pigs,Chicken. They are always in farm

Answer:

yes

Explanation:

this is simple

the horizontal line is adjacent

the vertical line is opposite

recall that cos x=adj/hyp

adj=hyp(cos x)

while opp=hyp(sin x)

Answer:

The correct option is;

3. The total mechanical energy is constant as the block moves back and forth

Explanation:

The total mechanical energy is the sum of the potential and kinetic energies of the system

For a system that is isolated from the effects of external forces, but being acted upon by the internal conservative forces within the system, the total mechanical energy is constant

For a black and spring system, we have total mechanical energy, E = 1/2×K×A².

Where;

K = Constant

A = The amplitude of motion

Therefore, where there is no loss to friction, with A, remaining constant, the total mechanical energy will be constant.

Answer:

stationary in an electric field.

moving perpendicular to a magnetic field.

moving perpendicular to an electric field.

Explanation:

Negative charge: In physics, the term "negative charge" is defined as a phenomenon that consists of a surplus or different electrons in any field i.e magnetic or electric field.

However, the correct answer in the question above, would be:

"stationary in an electric field".

"moving perpendicular to a magnetic field".

"moving perpendicular to an electric field".

Answer:

I do not agree with the answer.

Because in reality, the atom has 2 main parts and 3 subatomic particles.

Explanation:

The parts of an atom are:

- The crust: It is the outer part of the atom and is the place where the electrons are.

- The nucleus: It is the central part of the atom and is the place that contains the protons and neutrons.

The subatomic particles of the atom are:

- Electrons: They are negatively charged particles that go in the atom's crust and are divided into specific sections.

- Protons: They are particles with a positive electric charge, the number of protons in the nucleus of an atom is what determines the atomic number of an element.

- Neutrons: They are atoms with no electric charge.

Answer:

The evaporation time gradually increased with the increase in surfactant concentration, i.e., from water to the concentration level of 0.005%. Furthermore, the evaporation time is significantly reduced, even lower than that of water containing relatively high concentrations from 0.01% to 0.1%.

Answer:

The momentum of an object is equal to the product of its mass and its velocity.

Explanation:

Consider an object of mass [tex]m[/tex] travelling at a velocity [tex]\vec{v}[/tex]. The momentum [tex]\vec{p}[/tex] of this object would be:

[tex]\vec{p} = m \cdot \vec{v}[/tex].

For the law of conservation of momentum, consider two objects: object [tex]\rm a[/tex] and object [tex]\rm b[/tex]. Assume that these two objects collided with each other.

The sum of the momentum of the two objects would be:

Assume that the system of these two objects is isolated. By the law of conservation of momentum, the sum of the momentum of these two objects should be the same before and after the collision. That is:

[tex]m_{\rm a}\cdot \vec{v}_{\rm a}(\text{initial}) + m_{\rm b}\cdot \vec{v}_{\rm b}(\text{initial}) = m_{\rm a}\cdot \vec{v}_{\rm a}(\text{final}) + m_{\rm b}\cdot \vec{v}_{\rm b}(\text{final})[/tex].

Answer:  392N

Explanation: W=mg

                 W= 40x9.8

                     = 392N

Answer:

[tex]\large \boxed{\sf 392.4 \ N}[/tex]

Explanation:

[tex]\sf Weight \ (N) =mass \ (kg) \times acceleration \ of \ gravity \ (m/s^2)[/tex]

[tex]W=mg[/tex]

[tex]W=40 \times 9.81[/tex]

[tex]W= 392.4[/tex]

Answer:

The angular acceleration α = 14.7 rad/s²

Explanation:

The torque on the rod τ = Iα where I = moment of inertia of rod = mL²/12 where m =mass of rod  and L = length of rod = 4.00 m. α = angular acceleration of rod

Also, τ = Wr where W = weight of rod = mg and r = center of mass of rod = L/2.

So Iα = Wr

Substituting the value of the variables, we have

mL²α/12 = mgL/2

Simplifying by dividing through by mL, we have

mL²α/12mL = mgL/2mL

Lα/12 = g/2

multiplying both sides by 12, we have

Lα/12 × 12 = g/2 × 12

αL = 6g

α = 6g/L

α = 6 × 9.8 m/s² ÷ 4.00 m

α = 58.8 m/s² ÷ 4.00 m

α = 14.7 rad/s²

So, the angular acceleration α = 14.7 rad/s²

Answer:

The time she takes to reach the water from when she jumps off the platform is 1.71 s

Explanation:

According to the equations of motion, we have;

v = u - g·t

v² = u² - 2·g·s

s₁ = u₁·t₁ + 1/2·g₁·t₁²

The given parameters are;

The height of the platform (assumption: above the water) = 10 m

The velocity with which she jumps, u = 3 m/s

The acceleration due to gravity, g = 9.81 m/s²

The height to which she jumps, s, is found as follows;

v² = u² - 2·g·s

At maximum height, v = 0, which gives;

0 = 3² - 2×9.81×s

2×9.81×s = 3² = 9

s = 9/(2×9.81) = 0.4587 m

s = 0.4587 m

The time to maximum height, t, is found as follows;

v = u - g·t

0 = 3 - 9.81×t

9.81×t = 3

t = 3/9.81 = 0.3058 s

The total distance, s₁ from maximum height to the water surface = s + 10 = 0.4587 + 10 = 10.4587 m = 10.46 m

The time to reach the water from maximum height, t₁, is found as follows;

s₁ = u₁·t₁ + 1/2·g₁·t₁²

Where;

s₁ =  The total distance from maximum height to the water surface = 10.46 m

u₁ = The initial velocity, this time from the maximum height = 0 m/s

g₁ = The acceleration due to gravity, g (positive this time as the diver is accelerating down) = 9.81 m/s²

t₁ = The time to reach the water from maximum height

Substituting the values gives;

s₁ = u₁·t₁ + 1/2·g₁·t₁²

10.46 = 0·t₁ + 1/2·9.81·t₁²

t₁²= 10.46/(1/2×9.81) = 2.13 s²

t₁ = √2.13  = 1.46 s

Total time = t₁ + t = 1.46 + 0.3058 = 1.7066 ≈ 1.71 s.

Therefore, the time she takes to reach the water from when she jumps off the platform = 1.71 s.

Answer:

38.024 KWh

Explanation

250 watts multiplied with 5 hours daily multiplied with 28 days monthly equals 35000 Watt hours. Divided by a 1000 to get the KWh equals 35 KWh.

= 250×5hrs× 28days

= 35000watts

= 35000/1000

= 35KWh

Four 6 watt lightbulbs equals 24 watts 4x6=24

Hence, 24×4.5hrs×30days

= 3024watts

= 3024/1000

= 3.024KWhr

The total amount of energy consumed in the month of February = 35 KWh + 3.024 KWh = 38.024 KWh

Note that I had to use 28days since we are considering the month of February.

Answer:

1,860

Explanation:

Answer:

Height of pole = Height of giraffe

Explanation:

Given:

Height of giraffe = 20 ft

Height of pole = 240 inch

Find:

Which is taller

Computation:

Height of giraffe = 20 ft

We know that 1 ft = 12 inch

So,

Height of giraffe = 20 × 12 inch

Height of giraffe = 240 inch

and

Height of pole = 240 inch

Height of pole = Height of giraffe

Answer: React with the skin

Explanation:

lab safety test Safety goggles and an apron must be worn when handling chemicals labeled corrosive because they React with the skin

Answer:

A)0.00966 N/C

B) counterclockwise direction

Explanation:

We are given;

Diameter of the metal ring; d = 4.3 cm

Radius;r = 2.15 cm = 0.021- m

Initial magnetic field, B = 1.12 T

Rate of decrease of the magnetic field;dB/dt = 0.23 T/s

Now, as a result of change in magnetic field, an emf will be induced in it. Thus, , electric field is induced and given by the formula :

∫E•dr = d/dt∫B.A •dA

This gives;

E(2πr) = dB/dt(πr²)

Gives;. 2E = dB/dt(r)

E = dB/dt × 2r

We are given;

E = 0.23 × 2(0.021)

E = 0.00966 N/C

The magnitude of the electric field induced in the ring has a magnitude of 0.00966 N/C

B) The direction of electric field will be in a counterclock wise direction when viewed by someone on the south pole of the magnet

Answer:

a)0.51°

b)1.47×10^-4m

Explanation:

a)for a single slit experiment, the minima that has an angle of θ towards the centre needs to satisfy the expression below.

bsin(θ)= mλ.........................(*)

Where b= width of the slit

The distance on the screen from Central angle can be expressed as

Sin(θ)= y/d............. (**)

d and y is the horizontal distance between slit and screen

If we input eqn(**) into equation (*) we have

y= mλd/b................(z)

In order to find angle (θ) we have

(θ)= sin-(1.99×10^-2)/2.25

= 0.51°

Therefore, angle of diffraction θ of the second minimum is 0.51°

b)to find the width of the sloth using eqn(z) by substitute the values, we have

b= (2)(649×10^-9)(2.25)/1.99×10^-2

b= 1.47×10^-4m

Therefore, the width of the slit is 1.47×10^-4m

Answer:

1. a) Astronomers use the parallax method to measure the distance to nearby stars, but

we can’t use it to measure the distance to stars in other galaxies. Why not? Why isn’t the

parallax method useful for measuring the distances to stars in other galaxies?

They are so distant that the parallax is too small to be measured since parallax varies

inversely with distance.

b) Instead of the parallax method, we use the standard candle method to measure the

distance to stars in other galaxies. In particular, we use the standard candle method to

measure the distances to Cepheid variable stars in other galaxies. What is special about

Cepheid variable stars that makes them useful for this purpose?

We can figure out their luminosities from their periods of variation. Then if we measure

their fluxes we can calculate their distances.

2. a) From what were the protons and electrons in your body made, and roughly when

were they made?

They were made from energy (or gamma rays) very soon after the big bang (in the first

second). 400,000 years later they got together to make hydrogen atoms.

b) From what were the carbon atoms in your body made, and where were they made?

They were not made in the big bang. They were made much later inside of stars or in

supernovae. They were made by fusion from lighter atoms.

3. Make two sketches of the Milky Way Galaxy, one an edge-on view and one a face-on

view, labeling the various parts of the galaxy.

You should have labeled the

Answer:

1. Tienes 1 kg de fruta.

2. Queda por recorrer 1/4 km.

3. Ambos pesan lo mismo.

Explanation:

1. Tienes 1/2 kg y cuando te doy 1/4 te queda:

[tex] m = \frac{1}{2} - \frac{1}{4} = \frac{1}{4} [/tex]

Ahora cuando te doy 3/4 kg te queda en total:

[tex] m_{T} = \frac{1}{4} + \frac{3}{4} = 1 kg [/tex]

Por lo tanto, tienes 1 kg de fruta al final.

2. Si falta por recorrer la mitad de la mitad, tenemos:

[tex] d = \frac{1/2}{2} = \frac{1}{4} [/tex]

Entonces, queda por recorrer 1/4 km.

3. El peso (P) del hierro es:

[tex] P = m*g [/tex]    

[tex] P = (1 + 1/2)kg*9.81 m/s^{2} = 14.72 N [/tex]

Y el peso de la paja es:

[tex] P = 3/2 kg*9.81 m/s^{2} = 14.72 N [/tex]

Por lo tanto, ambos pesan lo mismo.

Espero que te sea de utilidad!

Answer: C. when the forces acting on the object are balanced.

Answer:

c

Explanation:

Answer:

30°

Explanation:

The angle between the normal and the vertical is the same as the angle between the incline and the horizontal.  We can show this with geometry.

Answer:

The velocity and direction after 1 second is 8.1 m/s downwards

Explanation:

The equation of motion for an object in free fall can be written as follows;

v = u + g×t

Where;

v = The final velocity of the object

u = The initial velocity of the object = 0 m/s

g = The acceleration due to gravity = 9.81 m/s²

The velocity after one second is given by the velocity equation as follows;

v = 0 + 9.81 m/s² * 1 s = 9.81 m/s

The direction of the is downwards due to the attraction by the Earth's gravitational field which acts towards the Earth's center

Therefore, the velocity and direction after 1 second is 8.1 m/s downwards.

Answer:

Take up space

Explanation:

Actually we know this by the definition of matter which states that "matter is any substance that has mass and takes up space by having volume."

hope it helped you:)

Answer:

we learned that an object that is vibrating is acted upon by a restoring force. The restoring force causes the vibrating object to slow down as it moves away from the equilibrium position and to speed up as it approaches the equilibrium position. It is this restoring force that is responsible for the vibration. So what forces act upon a pendulum bob? And what is the restoring force for a pendulum? There are two dominant forces acting upon a pendulum bob at all times during the course of its motion. There is the force of gravity that acts downward upon the bob. It results from the Earth's mass attracting the mass of the bob. And there is a tension force acting upward and towards the pivot point of the pendulum. The tension force results from the string pulling upon the bob of the pendulum. In our discussion, we will ignore the influence of air resistance - a third force that always opposes the motion of the bob as it swings to and fro. The air resistance force is relatively weak compared to the two dominant forces.

The gravity force is highly predictable; it is always in the same direction (down) and always of the same magnitude - mass*9.8 N/kg. The tension force is considerably less predictable. Both its direction and its magnitude change as the bob swings to and fro. The direction of the tension force is always towards the pivot point. So as the bob swings to the left of its equilibrium position, the tension force is at an angle - directed upwards and to the right. And as the bob swings to the right of its equilibrium position, the tension is directed upwards and to the left. The diagram below depicts the direction of these two forces at five different positions over the course of the pendulum's path.

that's what I know so far