Answer:
65000g
24.325 hrs
7500m
Answer:
I) 65000 g II)24.325 hours III)7500 m
Explanation:
I) 1 kg = 1000 g
65 kg = 65 * 1000 g = 65000 g
II) 1 hour = 3600 seconds
1 second = 1/3600 hours
87570 seconds = 87570 * 1/3600 hours =24.325 hours
III) 1 km = 1000 m
7.5 km = 7.5 * 1000 m = 7500 m
is there any machine that is 100% efficient? why?why not
Answer:
No, it's not there.
Explanation:
For a machine to be 100% efficient, it has to be with an output which is equal to its input. But machines have an out put less than an input, hence efficiency below 100%.
What is the relation between the weight of a body and acceleraton due to gravity?
Answer:
All objects on Earth, regardless of their mass, accelerate due to gravity at the same rate - that is, 9.8 m/sec2. The weight of an object can be calculated using the formula for force - F = m * a - where F equals the weight of the object and now the acceleration (a) is the acceleration of gravity (g).
state the term used to describe the turning force exerted by the man pushing down on a lever to lift one end of a heavy log
The term used to describe the turning force exerted when pushing an object is effort.
What is effort?The is the input force or force applied at one point of a lever in order to overcome a load.
The relationship between effort, load and mechanical advantage of a lever is given as;
M.A = L/E
where;
M.A is mechanical advantageL is the loadE is the applied force or effortThus, the term used to describe the turning force exerted when pushing an object is effort.
Learn more about effort here: https://brainly.com/question/24237657
Derive the following equations. :a=u-v by t
The heat required to raise 3 kg of copper from 0°C to 10°C raises 1kg of lead from 10°C to 100°C. If the specific heat capacity of copper is 0.095 cal/g°C,find the specific heat capacity of lead.
The specific heat capacity of lead has been determined to be 0.032 cal/g°C.
The specific heat capacity of a substance is the amount of heat required to increase the temperature of its unit mass by 1 Kelvin rise in temperature. There is no phase change during the process. This can be expressed as:
Q = mcT
c = [tex]\frac{Q}{mT}[/tex]
Where c is the specific heat capacity of the substance, Q is the quantity of heat required, m is the mass of the substance and T is its change in temperature.
In the given question, the heat emitted by the copper mass would be absorbed by the lead mass.
So that;
heat emitted by copper = heat absorbed by lead
[tex]m_{c}[/tex] [tex]c_{c}[/tex]([tex]T_{2}[/tex] - [tex]T_{1}[/tex]) = [tex]m_{l}[/tex][tex]c_{l}[/tex]([tex]T_{2}[/tex] - [tex]T_{1}[/tex])
With the given information in the question, the above equation is expressed as:
3 * 0.095 * (10 - 0) = 1 * [tex]c_{l}[/tex]* (100 - 10)
3*0.095*10 = [tex]c_{l}[/tex] * 90
2.85 = [tex]c_{l}[/tex]*90
[tex]c_{l}[/tex] = [tex]\frac{2.85}{90}[/tex]
= 0.031667
[tex]c_{l}[/tex] = 0.032 cal/g°C
Therefore, the specific heat capacity of lead is 0.032 cal/g°C.
For more clarifications, visit: https://brainly.com/question/22991121
Which are characteristics of a prokaryotic cell? Select three options.
O contains DNA
O lacks DNA
O contains ribosomes
O lacks ribosomes
O contains a nucleus
O lacks a nucleus
I NEED THIS QUICKLY
Answer:
A. Contains DNA
C. Contains ribosomes
F. Lacks a nucleus
Explanation:
Which property do the elements in each column of the representative elements series of the periodic table have in common?(1 point)
number of neutrons
number of orbitals
number of valence electrons
number of protons
The property that the elements in each column of the representative elements series of the periodic table have in common is: number of valence electrons.
An atom can be defined as the smallest unit comprising of matter that forms all chemical elements. Thus, atoms are basically the building blocks of matters and as such determines or defines the structure of a chemical element.
Generally, atoms are typically made up of three distinct particles and these are protons, neutrons and electrons.
Periodic table is an organized tabular array of all the chemical elements arranged in order of increasing atomic number (in rows).
Valence electrons can be defined as the number of electrons present in the outermost shell of an atom. Valence electrons are used to determine whether an atom or group of elements found in a periodic table can bond with others. Thus, this property is typically used to determine the chemical properties of elements.
In the periodic table, chemical elements that are having the same number of valence electrons are found in the same column.
This ultimately implies that, all the chemical elements such as Hydrogen, Sodium, etc., with one (1) valence electrons in their outermost shell (S-orbital) are found in the first (1st) column of the periodic table.
In conclusion, property that the chemical elements in each column of the representative elements series of the periodic table have in common is number of valence electrons.
Find more information: https://brainly.com/question/18214726
e. write unit of the following physical quantities
Answer:
electric current=ampere(A)
force=Newton (N)
area=metres square(m^2)
power=watt(w)
density=kg/m3
amount of substance =mole per cubic meter (mol/m3).
volume=cubic meter (m3),
Answer:
thanks for brainlist brother.........
Part B After producing electricity in many different ways, describe what causes electricity to flow in the coil? In your response, describe the types of forces acting on the electrons and how they result in movement.
Explanation:
If a coil of wire is placed in a changing magnetic field, a current will be induced in the wire. ... A changing magnetic field through a coil of wire therefore must induce an emf in the coil which in turn causes current to flow.
Due to the flow of the current run, the coil magnetic field is produced. Magnetic fields result in magnetic force.
What is electric force?The electric force between the two charges is directly propotional to the product of the charge and inversly propotional to the square of the distance between them.
A current will be generated in a wire coil if it is put in a changing magnetic field. As a result, a changing magnetic field through a coil of wire must create an emf in the coil, causing the current to flow.
A current is induced in a coil of wire when it is put in a changing magnetic field. Something generates an electric field that drives the charges around the wire, causing the current to flow.
Hence due to the flow of the current in the coil magnetic field is produced.
To learn more about the electric force refer to the link;
https://brainly.com/question/1076352
Describe the laws of liquid pressure and Explain the term fluid. (Please give the correct answer, it's really urgent)
Answer:
The laws of liquid pressure are
(i) Pressure inside the liquid increases with the depth from the free surface of the liquid.
(ii) Pressure is same at all points on a horizontal plane, in case of stationary liquid.
(iii) Pressure is same in all directions about a point inside the liquid.
(iv) Pressure at same depth is different in different liquids. It increases with the increase in the density of the liquid.
(v) A liquid will always seek its own level.
A Fluid is any liquid or gas or generally any material that cannot sustain a tangential, or shearing, force when at rest.
Explanation:
# Astronaut fells weightlessness in a spacecraft why?
Answer:
......... ........ ... .... .... . .. .......
.....
Explanation:
........mmmmmmmmmmm
A 20 kg truck drives in a circle of radius 4 m at 10m/s. What causes
the circular motion?
A. Normal Force
B. Friction
C. Tension
D. Gravity
Answer:
Normal force
Explanation:
The force is centipetral forceCalculating :-
Mass=m=20kgRadius=r=4mVelocity=10m/s=vWe know
[tex]\boxed{\sf F_c=\dfrac{mv^2}{r}}[/tex]
[tex]\\ \sf\longmapsto F_c=\dfrac{20(10)^2}{4}[/tex]
[tex]\\ \sf\longmapsto F_c=\dfrac{20(100)}{4}[/tex]
[tex]\\ \sf\longmapsto F_c=\dfrac{2000}{4}[/tex]
[tex]\\ \sf\longmapsto F_c=500N[/tex]
Mercury is used in thermometer.Give reason
Answer:
Mercury is the only one in liquid state at room temperature
I NEED HELP ASAP!!!
What is the average speed shown on the graph between point A and point D?
Answer:
5/3 m/s or
6 km/h
Explanation:
really ? the average speed is just the straight connection in the graph from A to D.
that means the travel time was 40-10 seconds = 30 seconds.
and the distance traveled was 60-10 = 50 meters.
so, the average speed was
50 meters / 30 seconds
to bring this to standard m/s
5 m / 3 s = 5/3 m/s
or to standard km/h
an hour has 60 minutes or 120 30-seconds intervals
50 m/ 30 s × 120/120 = 6000 m / h = 6 km/h
please help me with my question I will like and mark as brainliest for the first correct answer due tomorrow morning
Answer:
1845.26 ?
Explanation:
18.46 × 99.96= 1845.2616 = 1845.26
im not entirely sure though
An empty cardboard box falls from a high platform. Through the use of special equipment it was found that the energy of the cardboard box at the top of the fall was more than the energy of the box at the bottom of the fall. Explain.
Answer:
The mechanical energy of the cardboard box, M.E. = K.E. + P.E.
Where;
P.E. = The potential energy of the cardboard box = m·g·h
K.E. = The kinetic energy of the cardboard box = (1/2)·m·v²
Where;
m = Mass of the cardboard box
g = The (constant) acceleration due to gravity ≈ 9.81 m/s²
h = The height of the cardboard box
v = The velocity of the cardboard box
At the top of the fall, where h = The height of the platform = [tex]h_{platform}[/tex], and v = 0 (the box is initially at rest at the top), the M.E. is given as follows;
[tex]M.E._{top}[/tex] = P.E. + K.E. = m·g·[tex]h_{platform}[/tex] + (1/2) × m × 0² = m·g·[tex]h_{platform}[/tex]
However, at the bottom of the fall, the height of the box, h = 0, the velocity of the box, v = 0, therefore, the total energy at the bottom, after the box comes to rest, [tex]M.E._{bottom}[/tex] = 0
Therefore;
The total energy of the box at the top of the fall, .[tex]M.E._{top}[/tex] = m·g·[tex]h_{platform}[/tex] was more than the total energy of the box at the bottom of the fall,
[tex]M.E._{bottom}[/tex] = 0
Explanation:
2. A person jogs 4.0 km in 32 minutes, then 2.0 km in 22 minutes, and finally 1.0 km in 16 minutes.
What is the jogger's average speed in km per minute?
Answer:
0.1 km/min
Explanation:
7 / 70 = 0.1km/min
5. Which one of the following factors is directly proportional to density of liquid? (a) Temperature (b) Volume of liquid (c) Upthrust (d) Density of object
Answer:
A
The upthrust on a floating body is in upwards direction and is equal to the weight of the liquid displaced
B
The upthrust is directly proportional to the density of the liquid in which the solid is immersed
C
The upthrust is directly proportional to the volume of the fluid displaced by a solid
The upthrust acts on the body in upward direction at the center of buoyancy.
Upthrust is equal to the weight of liquid displaced by object and weight of liquid will depend on its density.
Upthrust is F=Vρg ,where V is the volume of liquid displaced and ρ is the density of fluid.
The total lateral pressure acting on an immersed object on one side is equal and in opposite direction to the total lateral pressure acting on the other side.
An airplane starts from rest and undergoes a uniform acceleration of 10.8 m/s^2 for 16.7 s seconds before leaving the ground. What is its displacement?
Answer:
3012.012m
Explanation:
s=it +1/2(10.8)(16.7)^2
A uniform, solid sphere of radius 2.50 cm and mass 4.75 kg starts with a purely translational speed of 3.00 m/s at the top of an inclined plane. The surface of the incline is 2.75 m long, and is tilted at an angle of 22.0∘ with respect to the horizontal. Assuming the sphere rolls without slipping down the incline, calculate the sphere's final translational speed v2 at the bottom of the ramp.
Answer:
The final translational seed at the bottom of the ramp is approximately 4.84 m/s
Explanation:
The given parameters are;
The radius of the sphere, R = 2.50 cm
The mass of the sphere, m = 4.75 kg
The translational speed at the top of the inclined plane, v = 3.00 m/s
The length of the inclined plane, l = 2.75 m
The angle at which the plane is tilted, θ = 22.0°
We have;
[tex]K_i[/tex] + [tex]U_i[/tex] = [tex]K_f[/tex] + [tex]U_f[/tex]
K = (1/2)×m×v²×(1 + I/(m·r²))
I = (2/5)·m·r²
K = (1/2)×m×v²×(1 + 2/5) = 7/10 × m×v²
U = m·g·h
h = l×sin(θ)
h = 2.75×sin(22.0°)
∴ 7/10×4.75×3.00² + 4.75×9.81×2.75×sin(22.0°) = 7/10 × 4.75×[tex]v_f[/tex]² + 0
7/10×4.75×3.00² + 4.75×9.81×2.75×sin(22.0°) ≈ 77.93
∴ 77.93 ≈ 7/10 × 4.75×[tex]v_f[/tex]²
[tex]v_f[/tex]² = 77.93/(7/10 × 4.75)
[tex]v_f[/tex] ≈ √(77.93/(7/10 × 4.75)) ≈ 4.84
The final translational seed at the bottom of the ramp, [tex]v_f[/tex] ≈ 4.84 m/s.
You toss an apple across the room to a friend. Which of the following statements is true about the apple at the top of its trajectory?
A. Its acceleration is zero.
B. The horizontal component of its velocity is zero.
C. The vertical component of its velocity is 9.8 m/s down.
D. Its acceleration is 9.8 m/s2 down.
valancy of an atom is +2. what does it mean.
Answer: I hope you find it useful
Explanation: Group 2 elements have two valence electrons. The two valence electrons are easily lost in the formation of chemical bonds. Once the two electrons are lost, the atom then has a full outer shell and is therefore more stable.
so, if an atom has valency 2 , then it means that the atom can combine with 2 other atoms .
why do the other animals listen to old major speak in the barn late on night?
6. 15. A boy takes 5 seconds to reach each point from ‘A’ to ‘B’, ‘B’ to ‘C’ and ‘C’ to ‘D’ as
shown in the diagram. If AB = BC = CD = 20 m then which of the following information is
correct when the boy reaches point D from point A via BC?
Explanation:
Could you also show the diagram
Our Moon a. was a separate small planet before it was captured by the Earth's gravity. b. spun off the fast-spinning Earth during the early formation of the Solar System. c. coalesced from gas and dust in its current place next to the Earth. d. was formed by the collision of the Earth with a Mars-sized protoplanet.
Answer:
d. was formed by the collision of the Earth with a Mars-sized protoplanet.
According to the The giant-impact hypothesis the Moon was formed from the debris of a collision between the Earth and a Mars-sized protoplanet.
A bike travels at 3.0 m/s, and then accelerates to a speed of
8.5 m/s in a time of 2.5 seconds. The average acceleration of
the bike is
m/s2
The average acceleration of the bike is 2.2 m/s²
What is average acceleration?Acceleration, rate at which velocity changes with time, in terms of both speed and direction.
A point or an object moving in a straight line is accelerated if it speeds up or slows down.
According to the question,
Given, initial velocity, u=3.0m/s and final velocity v=8.5 m/s
Time = 2.5 seconds
If a be the acceleration.
a = [tex]\frac{v-u}{t}[/tex]
a = [tex]\frac{8.5 - 3.0}{2.5s}[/tex]
⟹ a=2.2 m/s²
So, The average acceleration of the bike is 2.2 m/s²
Learn more about average acceleration here:
https://brainly.com/question/2303856
#SPJ2
any person for the job he applied Force moment or torque
Answer:
i think torque is the answer not confirmed
A stone is thrown into a pond. Five waves were made from the same source in 10 seconds.
The frequency of the wave for the stone thrown in the pond is 0.5Hertz.
The question does not specify what to calculate but we can look for the frequency of the wave.
Frequency is the number of oscillations completed in one second. This is interpreted as:
x oscillations = 1second
If Five waves were made from the same source in 10 seconds for a stone that is thrown inside the pond, then:
5 oscillations = 10seconds
Divide both expressions to get x (the required frequency)
x/5 =1/10
Cross multiply
10x = 5
Divide both sides by 10
10x/10 = 5/10
x = 1/2
x = 0.5Hertz
Hence the frequency of the wave is 0.5Hertz.
NB: The period of the wave is simply the reciprocal of the frequency.
Learn more here: https://brainly.com/question/13728731
difference between uniform motion and non uniform motion
Answer:
Uniform motion is a type of motion that is characterized as the motion of an object wherein the object moves in a straight line and its velocity remains unchanged along that line, regardless of the duration of time, as it occupies equal distances at equal time interval and Non-uniform motion is described as the motion of an object wherein the object moves at different speeds and does not cover the same distance at equal time intervals, regardless of the duration of the time interval.
Answer:
hope it's help you
Explanation:
In Uniform motion, the movement of a body is along the straight line with constant speed. In non uniform motion, the movement of a body is along the straight line with variable speed. In uniform motion, the body covers equal distance in an equal interval of time.
Robin fired a bullet of mass 100 gm from a gun of mass 5 kg. The bullet leaves the gun with a speed of 400 m/s. After penetrating 4 cm of a plank of 10 cm, the bullet loses one third of its initial velocity.
a. Calculate the backward velocity of the gun?
b. Can the bullet penetrate the plank of the wood completely? Explain mathematically.
please help
(a) The recoil or backward velocity of the gun is 8 m/s.
(b) The bullet cannot penetrate the plank of the wood completely.
The given parameters include;
mass of the bullet, m₁ = 100 g = 0.1 kgmass of the gun, m₂ = 5 kginitial velocity of the bullet, u₁ = 400 m/sthickness of the plank, x = 10 cm(a) The backward or recoil velocity of the gun is calculated by applying the principle of conservation of linear momentum.
let the backward or recoil velocity of the gun = u₂m₁u₁ + m₂u₂ = 0
m₂u₂ = -m₁u₁
[tex]u_2 = -\frac{m_1u_1}{m_2} \\\\u_2 = - \frac{0.1 \times 400}{5} \\\\u_2 = -8 \ m/s[/tex]
Thus, the recoil or backward velocity of the gun is 8 m/s.
(b) determine if the bullet can penetrate the plank of the wood completely
the bullet traveled 4 cm and lost ¹/₃ of u₁the remaining distance to completely penetrate the plank = 6 cmthe final velocity of the bullet at 4 cm, v = 400 - ¹/₃ x 400 m/s = 266.67 m/sthe acceleration of the bullet is calculated as;
v² = u₁² + 2as
2as = v² - u²
[tex]a = \frac{v^2 -u_1^2}{2s} \\\\a = \frac{(266.67)^2 -(400)^2}{2\times 0.04} = -1.111 \times 10^6 \ m/s^2[/tex]
Finally, determine the distance traveled by the bullet when it comes to a complete stop, that is the final velocity = 0
[tex]v_f^2 = v^2 + 2ad\\\\2ad = v_f^2 - v^2\\\\d = \frac{v_f^2 - v^2}{2a} \\\\d = \frac{(0) - (266.67)^2}{2(-1.111\times 10^6)} \\\\d = 0.032 \ m[/tex]
d = 3.2 cm
The total distance traveled by the bullet inside the plank = 4 cm + 3.2 cm = 7.2 cm
Therefore, the bullet cannot penetrate the plank completely.
To learn more about linear momentum visit: https://brainly.com/question/15869303
