1. A physical quantity P is related to four observables a, b and c as follows: P= (a3b 2 /c4 ) The percentage errors of measurements in a, b and c are 1%, 4% and 2% respectively. What is the percentage error in quantity P?

Answers

Answer 1

Answer:

The percentage error in quantity P is 19%.

Explanation:

It is given that,

A physical quantity P is related to four observables a, b and c as follows:

[tex]P=\dfrac{a^3b^2}{c^4}[/tex]

The percentage errors of measurements in a, b and c are 1%, 4% and 2% respectively.

We need to find the percentage error in quantity P. It is given by :

[tex]\dfrac{\Delta P}{P}\times 100=(3\times \dfrac{\Delta a}{a}+2\times \dfrac{\Delta b}{b}+4\times \dfrac{\Delta c}{c})\\\\=3\times 1+2\times 4+4\times 2\\\\\dfrac{\Delta P}{P}\times 100=19\%[/tex]

So, the percentage error in quantity P is 19%.


Related Questions

identify properties of a human body system

Answers

Answer:

integumentary, skeletal, muscular, nervous, endocrine, cardiovascular, lymphatic, respiratory, digestive, urinary, and reproductive

Explanation:

and this is biology not physics

1 point
40 The diagram below shows an electrical circuit made up of a cell and three loads. The
voltage established by the cell and the resistance of each load is marked on the
diagram. Select the current flowing through the 3-ohm load.
www
1 ohm
12V
2 ohms
WWW
3 ohms
www
A. 4 amps
B. 2 amps
C. 5 amps
D. 0.25 amps
SPS106 DOK 3

Answers

Answer:

Option B. 2 A.

Explanation:

The following data were obtained from the question:

Resistance 1 (R1) = 1 Ω

Resistance 2 (R2) = 2 Ω

Resistance 3 (R3) = 3 Ω

Potential difference (V) = 12 V.

Current through the 3 Ω (I3) =?

Next, we shall determine the total resistance of the circuit.

This can be obtained as follow:

Resistance 1 (R1) = 1 Ω

Resistance 2 (R2) = 2 Ω

Resistance 3 (R3) = 3 Ω

Total resistance (R) =.?

R = R1 + R2 + R3

R = 1 + 2 + 3

R = 6 Ω

Next, we shall determine the current flowing in the circuit.

This can be obtained as follow:

From ohm's law,

Voltage (V) = current (I) x resistance (R)

V = IR

Potential difference (V) = 12 V.

Resistance (R) = 6 Ω

Current (I) =?

V = IR

12 = I x 6

Divide both side by 6

I = 12/6

I = 2 A.

Since the circuit is in series connection, therefore, the same current will flow through each resistor.

Therefore, the current through the the 3 Ω load is 2 A.

Convert 85 cm/min to m/s.

Answers

Explanation:

meter=100cm

cm=10^-2 m

min=60 sec

0.0141666667 m / s

The conversion of 85 cm/min would be 0.0133 m/s

What is Velocity?

The total displacement covered by any object per unit of time is known as velocity. It depends on the magnitude as well as the direction of the moving object.

As given in the problem position-time graph of an object.

As we know that slope of the position time curve represents the velocity of the object

As given in the problem we have to convert 85 cm/min to m/s.

Let us first convert the displacement in cm to meters

100 cm = 1 m

1 cm = 1/100 m

85 cm = 85×1/100 m

          = 0.85 m

similarly, convert time given in minutes to the seconds

1 min = 60 s

velocity = displacement /time

velocity  =  0.85 / 60 m/s

             =0.01333 m/s

Thus, we converted  85 cm/m into 0.0133 m/s

Learn more about Velocity from here

brainly.com/question/18084516

#SPJ2

the distance between two successive troughs of wave is 0.4m. If the frequency of the source is 825Hz, calculate the speed of the wave​

Answers

Answer:

speed=330m/s

Explanation:

the speed of wave is given as

speed(meter per second) =frequency(hertz) * wavelength(meters)

so using the above formula we substitute the figures given in the question in the formula we get

speed = 0.4*825

speed =330m/s

note m/s is the si unit for speed which is read as meter per second

therefore speed =330m/s

It is 5.00 km from your home to the physics lab. As part of your physical fitness program, you could run that distance at 10.0 km/hr (which uses up energy at the rate of 700 W ), or you could walk it leisurely at 3.00 km/hr (which uses energy at 290 W ).A. Which choice would burn up more energy? 1. running.2. walking.B. How much energy (in joules) would it burn?C. Why is it that the more intense exercise actually burns up less energy than the less intense one?

Answers

Answer:

a. Walking burns up more energy.

b. 1740 kJ

c. This is because more intense exercise releases a lot of energy in a short period of time, whereas, less intense energy releases it energy gradually over a long period of time.

Explanation:

a. We know energy W = Pt where P = power and t = time.

Now for walking, t = d/v where d = distance = 5.00 km and v = speed = 3.00 km/hr and P = 290 W

So, t = d/v = 5.00 km/3.00 km/hr = 5/3 hr = 5/3 × 3600 s = 6000 s

W = Pt = 290 W × 6000 s = 1740000 = 1740 kJ

Now for running, t = d/v where d = distance = 5.00 km and v = speed = 10.00 km/hr

So, t = d/v = 5.00 km/10.00 km/hr = 0.5 hr = 0.5 × 3600 s = 1800 s and P = 700 W

W = Pt = 700 W × 1800 s = 1260000 = 1260 kJ

Since walking burns up 1740 kJ and running burns up 1260 kJ, walking burns up more energy.

b. It burns up 1740 kJ

c. This is because more intense exercise releases a lot of energy in a short period of time, whereas, less intense energy releases it energy gradually over a long period of time.

Question 2 of 10
Which of the following is an Sl unit?
A. Foot
B. Inch
C. Meter
D. Mile
SUBMIT

Answers

Answer:

C. Meter

Explanation:

The International System of Unit (SI) is gotten from the french word Systeme international is a modern form of metric measurement. It is the system of measurement that is universally accepted. It is from this SI units that all other system of units are derived. There are seven basic SI units which are:

1) Length in Meter (m)

2) Time in Seconds (s)

3) Amount of Substance in mole (m)

4) Electric current in ampere (A)

5) Temperature in kelvin (k)

6) Luminous intensity in candela (cd)

7) Mass in kilogram (kg)

Brandon buys a new seadoo he goes 12 km north from the beach he jumps wakes for 6 km to the east the chases a boat 10 km north what distance did he cover what was his displacement

Answers

Answer:

Distance covered 28 km

displacement is 22.8 km North-East

Explanation:

Distance shows how far apart objects or points are from each other. The distance he covered is the sum of all the distance travelled. Therefore:

Distance covered = 12 km + 6 km + 10 km = 28 km

Displacement is a vector quantity (has direction). It is the overall change in position.

The total distance traveled north = 12 km + 10 km = 22 km

The distance traveled east = 6 km

The displacement (d) is:

d² = 22² + 6² = 484 + 36

d² = 520

d = √520 = 22.8 km

Therefore the displacement is 22.8 km North-East

Distance covered 28 km

displacement is 22.8 km North-East

The calculation is as follows:

Distance covered

= 12 km + 6 km + 10 km

= 28 km

Now

The total distance traveled north = 12 km + 10 km = 22 km

And,  

The distance traveled east = 6 km

So,  

The displacement (d) is:

[tex]d^2 = 22^2 + 6^2\\\\ d^2 = 520\\\\d = \sqrt520[/tex]

= 22.8 km

learn more: https://brainly.com/question/10813422?referrer=searchResults

whats suface tension

Answers

Answer: "Surface tension is a film of a liquid caused by the attraction of the particles in the surface layer by the bulk of the liquid, which tends to minimize surface area."

Hope this helps!

Answer:

Explanation:

Surface tension is the property of a liquid surface. It is an effect where the surface of the liquid is strong.

example - small insects can walk on water as they do not have enough weight to penetrate it.

This image might help you

Hope it helps

plz mark as brainliest!!!!!!!

Marco is conducting an experiment. He knows the wave that he is working with has a wavelength of 32.4 cm. If he measures the frequency as 3 hertz, which statement about the wave is accurate?

Answers

This question is incomplete; here is the complete question:

Marco is conducting an experiment. He knows the wave that he is working with has a wavelength of 32.4 cm. If he measures the frequency as 3 hertz, which statement about the wave is accurate?

A. The wave has traveled 32.4 cm in 3 seconds.

B. The wave has traveled 32.4 cm in 9 seconds.

C. The wave has traveled 97.2 cm in 3 seconds.

D. The wave has traveled 97.2 cm in 1 second.

The answer to this question is D. The wave has traveled 97.2 cm in 1 second.

Explanation:

The frequency of a wave, which is in this case 3 hertz, represents the number of waves that go through a point during 1 second. According to this, if the frequency of the wave is 3 hertz this means in 1 second there were 3 waves. Moreover, if you multiply the wavelength (32.4cm) by the frequency (3) you will know the distance the wave traveled in 1 second: 32.4 x 3 =  97.2 cm. This makes option D the correct one as the distance in 1 second was 97.2 cm.

Answer:Is D!

Explanation:TEAT(Sorry) -_-*

What is the difference between virtual images produced by concave, plane, and convex mirrors?
What does the negative sign in the value of magnification produced by a mirror indicate about
an image?

Answers

Answer:

Explanation:

A concave mirror is a curved mirror that is coated outwards. The outer part of the mirror is always coated. The nature of image formed by an object placed in front of a concave mirror can be real or virtual depending on the distance of the object on the axis from the mirror. The only time the object produces a virtual image is when it is placed between the focus and the pole of the mirror. The virtual image formed is a "MAGNIFIED and upright image"

For a convex mirror, the inner part is always coated and the nature of the image formed by the object doesn't depend on the distance between the image and the mirror. No matter where the object is placed, the image formed will always be virtual, upright and DIMINISHED. This means that magnification is always less than 1.

For a plane mirror, the nature of the image produced by a plane mirror also virtual because it is always formed behind the mirror. The size of the image formed is always THE SAME as that of the object. This means that the magnification is always equal to 1.

a) In summary, the difference between virtual images produced by concave, plane, and convex mirrors is that virtual images produced by concave mirror are MAGNIFIED, virtual images produced by plane mirror are THE SAME SIZE as that of the object and virtual images produced by convex mirrors are always DIMINISHED.

b) Magnification is defined as the ratio of the image distance to the object distance. Mag = v/u

Note that object distances are always positive, hence it is only the image distance that can either be positive or negative which in turn affects the magnification causing it to be positive or negative.

Negative image distance shows that the image is virtual while positive image distance shows that the image is real.

A negative magnification therefore shows that the nature of the image is a virtual image.

A train travels southwest from point A to point B through the Arizona desert at 55 mi/h. How far will the train travel six-and-a-half hours?

Answers

Explanation:

Distance = speed × time

d = (55 mi/hr) (6.5 hr)

d = 357.5 mi

Q1 b name the three tiny particles which make up atoms ? a write the charge alongside each one ?

Answers

Answer:

Protons

Neutrons

Electrons.

Protons + charge(positively charged)

Neurons no charge.

Electrons - ( negatively charged).

Explanation:

Atom is the smallest unit of a matter that constitutes chemical elements.

It is composed of three particles which are protons,neutrons and electrons.

Protons is positively charged,neuron has no charge and electrons is negatively charged.

Proton and neuron are found in the nucleus while electron is found outside the neuron.

Once a scientist has made a hypothesis, what would they typically do next? (2 points)
a
Analysis
b
Testing
C
Research
d
Sharing

Answers

Answer:Testing

Explanation:Once a scientist has made a hypothesis, what would they typically do TESTING nextn

Once a scientist has made a hypothesis, they would typically do testing, therefore the correct answer is option B

What is the scientific claim?

Scientific claims are statements made in science based on an experiment.

These Scientific claims are backed by the experimental data and their true results obtained from scientific investigation and experimentation.

When a scientist performs a fair test is one in which all other circumstances are maintained while just one variable is changed at a time.

Scientists frequently discover that their hypotheses and predictions were not supported by the results of their experiments. In these situations, they will communicate the findings of their experiment before revising their original hypotheses and predictions in light of the new knowledge they have gained.

The right response is option B because once a scientist has made a theory, they usually do testing.

Learn more about the scientific claims, here

brainly.com/question/11088441

#SPJ2

Which instrument is used to measure the height of a 20 litre jerrican​

Answers

tape measure?

Hope that helped!!! k

instrument is used to measure is Tape measure

what is a hypothesis reffered to as after being verified by a large number or independent experiments

Answers

Answer:

The hypothesis may or may not be true and needs to be tested. It might be the answer to the problem. Hence, it must be tested thoroughly. When these predictions are tested again and again in independent scientific experiments and gets verified, the hypothesis is converted into a scientific theory.

How much heat does 25 g of aluminum lose when cooled from 100 ° C to 20 ° C? Express your result in BTU

Answers

Answer:

1.7 BTU

Explanation:

q = mCΔT

q = (25 g) (0.9 J/g/°C) (100°C − 20°C)

q = 1800 J

q = 1800 J × (1 BTU / 1055 J)

q = 1.7 BTU

In the vertical columns of the periodic table:
Atomic weight increases from top to bottom.
Outer shell electrons increases from top to bottom.
The number of shells increases from top to bottom.
All the physical properties are identical.

Answers

Answer:

C. The number of shells increases from top to bottom

Explanation:

There are some trends about the periodic table, one of them is that in the vertical columns of periodic table, the number of shells increases from top to bottom.

From top to bottom in a periodic table, the number of electrons increases, thus more number of shells are needed to fill these electrons and the number of shells increases or we can say the atomic radius increases from top to bottom.

Hence, the correct option is "C".

what is the meaning of energy

Answers

Answer:

[tex]\boxed{\mathrm{view \ explanation}}[/tex]

Explanation:

Energy is the capacity of an object to do work. Energy must be transferred to an object in order to do work. The SI unit of energy is Joules (J).

Answer:

See below

Explanation:

Energy is the "capacity/ability to do work". If the body has the ability to do work, we mean that the body possesses energy.

Units:

Energy is measured in Joules (J)

Types:

The two "main" types of energy are:

1) Kinetic Energy

2) Potential Energy

Explain the structure of a clinical thermometer​

Answers

Explanation:

a clinical thermometer is a thermometer used to measure human body temperature. mostade in the 20th century are mercury-in-glass thermometer. they ate accurate and sensitive having a narrow place where the mercury level rises very fast. a kink in the tube stops the mercury level from falling on its own.

hope it helps you

A type of cuckoo clock keeps time by having a mass bouncing on a spring, usually something cute like a cherub in a chair. What force constant is needed to produce a period of 0.500 s for a 0.0150-kg mass

Answers

Answer:

the force constant  k = 2.369 N/m

Explanation:

Given that:

A type of cuckoo clock keeps time by having a mass bouncing on a spring, usually something cute like a cherub in a chair.

with period T = 0.500 s and a mass of 0.0150 kg, Then the force constant can be calculated by using the formula:

[tex]\mathtt{T = 2 \pi \ \sqrt{\dfrac{m}{k} }}[/tex]

where;

T = time period

m = mass

k = force constant.

By making k the subject of the formula; we have:

[tex]\mathtt{T^2 = 4 \pi^2 (\dfrac{m}{k})}[/tex]

[tex]\mathtt{k =\dfrac{4 \pi ^2 \ m}{T^2}}[/tex]

replacing our given values , we have:

[tex]\mathtt{k =\dfrac{4 (3.142) ^2 \ \times 0.0150 }{0.5^2}}[/tex]

[tex]\mathtt{k =\dfrac{39.49 \ \times 0.0150 }{0.25}}[/tex]

[tex]\mathtt{k =\dfrac{0.59235 }{0.25}}[/tex]

k = 2.369 N/m

According to the information available in the question, the force constant is 2.37N/m.

Using the relation;

T = 2π√m/k

T = period = 0.500 s

m = mass in kilograms = 0.0150-kg

k = spring constant = ?

Making k the subject of the formula;

k = 4π^2m/T^2

k = 4 × (3.142)^2 ×  0.0150/(0.500 )^2

k = 2.37N/m

Learn more: https://brainly.com/question/6284546

Identifying Maller
In your own words, describe how matter is identified.

Answers

Answer:

Matter can be identified through its properties. One clue to helps us identify matter is magnetism. Magnetism is the ability of a material to be attracted by a magnet. Only certain materials are attracted to magnets, like iron, nickel, and cobalt.

Explanation:

we can identify matter by:  physical properties  and

chemical properties

what is the best defintion of efficency

Answers

Answer: Efficiency signifies a peak level of performance that uses the least amount of inputs to achieve the highest amount of output.

Explanation: It minimizes the waste of resources such as physical materials, energy, and time while accomplishing the desired output.

Answer:

The efficiency of a simple machine is defined as the ratio of useful work done by the machine ( output work) to the total work out into the machine ( input work).

Explanation:

Efficiency

If a machine overcomes a load ' L ' and the distance travelled by the load is 'Ld' , the work done by the load is L× LD. It is also called output work or useful work.

Therefore, [tex] \boxed{Output \: work \: = L \: \times \: Ld}[/tex]

Likewise, The effort applied to overcome the load is 'E' and the distance covered by effort is 'Ed' , the work done by effort is E × Ed. It is also called input work.

Therefore, [tex] \boxed{Input \: work = E \times Ed}[/tex]

The efficiency of a simple machine is defined as the ratio of output work to the input work .

Therefore, [tex] \boxed{Efficiency ( η)= \frac{outpt \: work}{input \: work} \times 100\%}[/tex]

Efficiency is expressed in percentage. It is a ratio of two works. A machine is never 100% efficient. It is because no machine is friction free and due to friction, some of the input energy is wastes in the form of heat energy.

[tex] \mathrm{Hope \: I \: helped!}[/tex]

[tex] \mathrm{Best \: regards!}[/tex]

Which term describes the ability to process many things simultaneously?

O Effortful processing

O Parallel processing

O Mood congruent memory

O Flashbulb memory

O Working memory

Answers

Answer:

Parallel processing

Explanation:

It is a parallel processing because it involves the brain processing many part of problem simultaneously.

The brain natural mode of information involves performing many task .

It is also ability of the brain to simultaneously process incoming stimuli or signals of different quality. It is a part of brain's vision and divide what is seen into four major parts which are color, motion, shape, and depth.

Answer: B)  Parallel processing

an astronaut takes a tuning fork with her to the moon she strikes it inside the cabin the cabin is normally filled with air so the humans inside the spacecraft are comfortable she also strikes it outside the spacecraft when she gets down on the surface of the moon which of the following is true about the tuning fork?
A: it does not vibrate inside the spacecraft
B: id does not vibrate on moon surface
C: it vibrations are not transmitted inside the spacecraft
D:it's vibrations are not transmitted to the moon's atmosphere

Answers

Answer:

d

Explanation:

a and b: it vibrates in both the difference is whether you hear the sound or not the lack or presence of molecules does not hinder the timing fork from vibrating but can hinder you from hearing since sound is a mechanical wave therefore require a medium bringing us to (c) these vibrations are transmitted because there is presence of a medium i.e air molecules so sound can be heard

but in (c) it is true since the vibrations are created but are not transmitted to your ears due to lack of a medium

A 1000 kg car developed a snag and is standing in the middle of a road. The driver and a help pulled it with two ropes respectively with forces 200√2 N 45° east of south and 400N 30° north of east. Assuming negligible friction, find the acceleration of car

Answers

Answer:

Acceleration = 0.1464 m/s^2

Explanation:

From the question, the parameters given are:

Mass m = 1000 kg

The driver and a help pulled it with two ropes respectively with forces 200√2 N 45° east of south and 400N 30° north of east

Find the resultant force along the x axis.

(400 × cos30) - (200√2 × cos45)

346.4 - 200 = 146.4 N

therefore, the resultant force = 146.4N

The formula to use for the acceleration of the car is

F = ma

Where

F = resultant force

M = mass of the car

a = acceleration of the car

Substitute f and m into the formula

146.4 = 1000 × a

Make a the subject of formula

a = 146.4 / 1000

a = 0.1464 m/s^2

Therefore, the car accelerate at 0.1464 m/s^2

A golfer misjudges a putt and leaves her ball way short, the ball going only half of the way to the hole. If the speed of the ball leaving the putter in the first case was vo and the force of resistance due to the grass remains the same, what speed should she have given to the ball to make the original putt?

Answers

Answer:

Using

1/2mv^2 = work done by friction

work done = force x distance

lets call the force 3 N

lets call v = 3 m/s

lets call mass = 2 kg

0.5 x 2 x 3^2 = 9 J

9/3N = 3 m/s

now times 3 m/s by square root of 2 of which is 1.4142

3 x 1.4142= 4.2426 m/s

0.5 x 2 x 4.2426^2 = 18

18/2N = 9 m

what is physics and important of physics​

Answers

Physics is the explanation of our reality, both visible and invisible. With it we can understand the world around us, why things are how they are, and why things do what they do. This understanding allows humans to develop objects that improve quality of life.

Answer:

Confusion

question:
is it multiple choice? or you have to write it

An object is moving along a circular track of radius 7 m with constant speed 11 m/s. Its average velocity after 8 second of the start is

Answers

Answer:

0 m/s

Explanation:

Average velocity is displacement over time.

v_avg = Δx / Δt

Displacement is the distance between the start and the finish.

The circumference of the track is:

C = 2πr

C = 2π (7 m)

C ≈ 44 m

The distance covered by the object is:

d = vt

d = (11 m/s) (8 s)

d = 88 m

So the object travels 2 circumferences, meaning it ends back where it started.  Therefore, the displacement is 0 m, and the average velocity is 0 m/s.

the standard unit of measurement of preasure
2. What is
N/m square or Pascal​

Answers

Answer:

Both are the same.

Explanation:

[tex]pressure= \frac{force}{area} = \frac{f}{a} = \frac{n}{m {}^{2} } [/tex]

The SI unit was named after Bláise Pascal to honor him.

Hope this helps ;) ❤❤❤

Describe what happens to water waves when they strike a flat surface?

Answers

Answer:

In this case reflection occurs.

Explanation:

This happens when they bounce on objects that they can not pass through.

Hope it helps

okay.

Other Questions
Solve for d.4d - 4 = 5d 8d = write an essay on one of the following topics. 1. we have to preserve our cultural heritages. 2. cultural heritages have multiple advantages to our country.3. our roles in valuing our cultural heritages . NoGrowth Corporation currently pays a dividend of per quarter, and it will continue to pay this dividend forever. What is the price per share of NoGrowth stock if the firm's equity cost of capital is ? Name the vertex ot XYZ. what is sexual reproduction Diego and Max are buying soft drinks for a neighborhood picnic. Each person isexpected to drink one can of soda. Diego says that if you multiply the unit price for acan of soda by the number of people attending the picnic, you will be able todetermine the total cost of the soda. Max says that if you divide the cost of a 12-pack of soda by the number of sodas, you will determine the total cost of the sodas.Which choices best illustrates who is correct and why?Max is incorrect because he calculated the cost of one can of sodaDiego is incorrect because he calculated the price of one can of sodaMax is correct because the total cost divided by the number of sodas gives youthe total cost of the sodas An important factor in selling a residential property is the number of people who look through the home. A sample of 17 homes recently sold in the Buffalo, New York, area revealed the mean number looking through each home was 19 and the standard deviation of the sample was 4 people.Develop a 98 percent confidence interval for the population mean. (Round your answers to 2 decimal places.)Confidence interval for the population mean is between and ? My first term paper, which is due next month, must be at least ten pages long.Identify the relative clause, whether it is essential to the meaning of the sentence, and if it requires commas.The clause is which is due next month.It is non-essential.It does require a comma.The clause is which is due next month.It is essential.It does not require a comma.The clause is My first term paper.It is essential.It does not require a comma.The clause is My first term paper.It is non-essential.It does require a comma. Evaluate the following expression for x = 1 and y = -3.3yx+x-y Point R divides PG in the ratio 1:3. If the x-coordinate of R is -1 and the x-coordinate of P is -3, what is the x-coordinate of Q Amos Manufacturing has two major departments. Management wants to compare their relative performance. Information related to the two departments is as follows:Division 1:Sales: $200,000Expenses: $150,000Asset investment: $950,000Division 2:Sales: $45,000Expenses: $35,000Asset investment: $200,000Based on ROI, which division is more profitable?a. Division 1b. Both divisions have the same ROI ratioc. Division 2 calculate the size of angle x. the sides are 8cm, 11cm and 15cm I need help again please The management of Cooper Corporation is considering the purchase of a new machine costing $420,000. The company's desired rate of return is 10%. The present value factors for $1 at compound interest of 10% for 1 through 5 years are 0. 909, 0. 826, 0. 751, 0. 683, 0. 621, respectively. In addition to this information, use the following data in determining the acceptability in this situation: Year Income from Operations Net Cash Flow 1 $100,000 $180,000 2 40,000 120,000 3 20,000 100,000 4 10,000 90,000 5 10,000 90,000 The present value index for this investment is a.1.45. b.1.08. c.0.92. d.0.36. If you were attending the flower festival in El Salvador, what is one thing you would do to prepare? All the following statements concerning term insurance are correct EXCEPT: Group of answer choices Most policies can be renewed for additional periods without evidence of insurability. Most policies can be converted to a permanent life insurance policy. Most policies have a nonforfeiture benefit to refund a portion of a policy's cash value when coverage stops. The insurance provides protection for a certain period of time. Suppose you see an advertisement for a video game that claims you can actually fly around inside your home while you play it. What do your scientific literacy and critical thinking skills lead you to think about that claim? how did ancient Greek and roman texts contribute to the rise of humanism in ltay Write the equation of the line that passes through (-1,5) and has a slope of 3 in point slope form Write the event as set of outcomes. When we roll two dice, the total showing is eight.A. {(2, 6), (3, 5), (4, 4), (5, 3), (6, 2)}B. {(2, 6), (3, 5), (4, 4)}C. {(2, 6), (3, 5), (5, 3), (6, 2)}D. {(1, 7), (2, 6), (3, 5), (4, 4), (5, 3), (6, 2), (7, 1)}