1. (16 points) True or False, one point each, Write down F (false) or T (true). ___ (01) In a mechanical design, it is recommended to use standard size/dimension to overcome uncertainties in stress or material strength

Answers

Answer 1

Answer:

True

Explanation:

I looked it up

Answer 2

Answer:

true

Explanation:


Related Questions

The radial component of acceleration of a particle moving in a circular path is always:________ a. negative. b. directed towards the center of the path. c. perpendicular to the transverse component of acceleration d. all of the above

Answers

Answer:

d. all of the above

Explanation:

There are two components of acceleration for a particle moving in a circular path, radial and tangential acceleration.

The radial acceleration is given by;

[tex]a_r = \frac{V^2}{R}[/tex]

Where;

V is the velocity of the particle

R is the radius of the circular path

This radial acceleration is always directed towards the center of the path, perpendicular to the tangential acceleration and negative.

Therefore, from the given options in the question, all the options are correct.

d. all of the above

There are different type of acceleration.  The radial component of acceleration of a particle moving in a circular path is always negative, directed towards the center of the path and perpendicular to the transverse component of acceleration.

Radial acceleration is simply known as the rate of change of angular velocity where the direction is towards the center about whose circumference, the body tend to shift.

This is due to because of the centripetal force. So centripetal force is the reason for a radial acceleration.

Learn more from

https://brainly.com/question/13308560

An air-conditioner which uses R-134a operates on the ideal vapor compression refrigeration cycle with a given compressor efficiency.
--Given Values--
Evaporator Temperature: T1 (C) = 9
Condenser Temperature: T3 (C) = 39
Mass flow rate of refrigerant: mdot (kg/s) = 0.027
Compressor Efficiency: nc (%) = 90

a) Determine the specific enthalpy (kJ/kg) at the compressor inlet.
Your Answer =
b) Determine the specific entropy (kJ/kg-K) at the compressor inlet
Your Answer =
c) Determine the specific enthalpy (kJ/kg) at the compressor exit
Your Answer =
d) Determine the specific enthalpy (kJ/kg) at the condenser exit.
Your Answer =
e) Determine the specific enthalpy (kJ/kg) at the evaporator inlet.
Your Answer =
f) Determine the coefficient of performance for the system.
Your Answer =
g) Determine the cooling capacity (kW) of the system.
Your Answer =
h) Determine the power input (kW)to the compressor.
Your Answer =

Answers

Answer:

A) 251.8 kj/kg

B) 0.9150 kj/kg-k

C) 155.4 kj/kg

F) 1.50

G) 3.95 kw

H) 2.6 kw

Explanation:

Given conditions :

air conditioner : R -134a

compressor efficiency (nc) = 90%.

T1 = 9⁰c,  T3 = 39⁰c, mass flow rate = 0.027 kg/s

A) Specific enthalpy at the compressor inlet

at T = 9⁰c the saturated vapor (x) = 1

from the R-134a property table

h1 = 251.8 kj/kg

B ) specific entropy ( kj/kg-k) at the compressor inlet

at T = 9⁰c the saturated vapor (x) = 1

s = 0.9150 kj/kg-k ( from the R-134a property table )

C) specific enthalpy at the compressor exit

at T3 = 39⁰c , s2 = s1

has = 165.12 kj/kg

h2 = 155.4 kj/kg

attached below is the remaining solution to some of the problems

9. A box contains (4) red balls, and (7) white balls ,we draw( two) balls with return , find 1. Show the sample space & n(s) ..... 2. Probability of all results that appeared in the sample space..

Answers

Answer:

The answers to your questions are given below.

Explanation:

The following data were obtained from the question:

Red (R) = 4

White (W) = 7

1. Determination of the sample space, S.

The box contains 4 red balls and 7 white balls. Therefore, the sample space (S) can be written as follow:

S = {R, R, R, R, W, W, W, W, W, W, W}

nS = 11

2. Determination of the probability of all results that appeared in the sample space.

From the question, we were told that the two balls was drawn with return. There, the probability of all results that appeared in the sample space can be given as follow:

i. Probability that the first draw is red and the second is also red.

P(R1) = nR/nS

Red (R) = 4

Space space (S) = 11

P(R1) = nR/nS

P(R1) = 4/11

P(R2) = nR/nS

P(R2) = 4/11

P(R1R2) = P(R1) x P(R2)

P(R1R2) = 4/11 x 4/11

P(R1R2) = 16/121

Therefore, the Probability that the first draw is red and the second is also red is 16/121.

ii. Probability that the first draw is red and the second is white.

Red (R) = 4

White (W) = 7

Space space (S) = 11

P(R) = nR/nS

P(R) = 4/11

P(W) = nW/nS

P(W) = 7/11

P(RW) = P(R) x P(W)

P(RW) = 4/11 x 7/11

P(RW) = 28/121

Therefore, the probability that the first draw is red and the second is white is 28/121.

iii. Probability that the first draw is white and the second is also white.

White (W) = 7

Space space (S) = 11

P(W1) = nW/nS

P(W1) = 7/11

P(W2) = nW/n/S

P(W2) = 7/11

P(W1W2) = P(W1) x P(W2)

P(W1W2) = 7/11 x 7/11

P(W1W2) = 49/121

Therefore, the probability that the first draw is white and the second is also white is 49/121.

iv. Probability that the first draw is white and the second is red.

Red (R) = 4

White (W) = 7

Space space (S) = 11

P(W) = nW/nS

P(W) = 7/11

P(R) = nR/nS

P(R) = 4/11

P(WR) = P(W) x P(R)

P(WR) = 7/11 x 4/11

P(WR) = 28/121

Therefore, the probability that the first draw is white and the second is red is 28/121.

(2x+y)dx+(x-2y)dy=0 solve the differential equation

Answers

Answer: y' = - x'

Explanation:

Let f(x) = 2x + y

then f'(x) = 2 + y'

Let f(y) = x - 2y

then f'(y) = x' - 2

Given:  f'(x) + f'(y) = 0

         2 + y' + x' - 2 = 0

                y' + x'= 0

                 y' = -x'

This can also be written as:       [tex]\dfrac{dy}{dx}=-\dfrac{d}{dx}[/tex]

What improves the structured approach in design?



A team is adopting a structured approach in design which helps them to improve the ___ of the design.

Answers

Answer:

efficiency

Explanation:

Answer:

The correct answer is Efficiency.

Explanation:

I got it right on the plato test.

As the asteroid falls closer to the Earth's surface its _______ energy decreases and its _______ energy increases.

Answers

Answer:

As the asteroid falls closer to the Earth's surface its Gravitational Potential energy decreases and its Kinetic energy increases.

Define centrifugal pump. Give the construction and working of centrifugal pump. ​

Answers

Centrifugal pump is a hydraulic machine which converts mechanical energy into hydraulic energy by the use of centrifugal force acting on the fluid. These are the most popular and commonly used type of pumps for the transfer of fluids from low level to high level.

You have accumulated several parking tickets while at school, but you are graduating later in the year and plan to return to your home in another jurisdiction. A friend tells you that the authorities in your home jurisdiction will never find out about the tickets when you re-register your car and apply for a new license. What should you do?

Answers

Answer:

pay off the parking tickets

Explanation:

In the scenario being described, the best thing to do would be to pay off the parking tickets. The parking tickets stay under your name, and if they are not paid in time can cause problems down the road. For starters, if they are not paid in time the amount will increase largely which will be harder to pay. If that increased amount is also not paid, then the government will suspend your licence indefinitely which can later lead to higher insurance rates.

Armature reaction in a dc machine A) is due to an increase of the armature voltage. B) occurs when the motor is connected to an ac power source. C) occurs when the motor is connected to a dc power source. D) is due to an increase of the armature current.

Answers

Answer:

D) is due to an increase of the armature current.

Explanation:

Option D is correct because on the DC motor, when the load increases, it leads to an increase in the armature current.

The armature current then sets up a magnetic flux which opposes the main field flux. The net field flux gets reduced. It is at this point, the armature reaction occurs.

Armature reaction is seen as the effect of magnetic flux which is usually set up by an armature current. This occurs when there is the distribution of flux under the main poles.

There are two effects the armature flux causes on the main field flux.

1. The main field flux is distorted by the armature reaction.

2. The magnitude of the main field flux is reduced by the armature flux.

Water at 20oC, with a free-stream velocity of 1.5 m/s, flows over a circular pipe with diameter of 2.0 cm and surface temperature of 80oC. Calculate the average heat transfer coefficient and the heat transfer rate per meter length of pipe.\

Answers

Answer:

Average heat transfer coefficient =  31 kw/m^2 k

Heat transfer rate per meter length of pipe =  116.808 KW

Explanation:

water temperature = 20⁰c,  

free-stream velocity = 1.5 m/s

circular pipe diameter = 2.0 cm = 0.02 m

surface temperature = 80⁰c

A) calculate average heat transfer coefficient

we apply the formula below :

m = αAv

A (area) = [tex]\pi /4 (d)^2[/tex]

m = 10^3 * [tex]\pi / 4 ( 0.02)^2[/tex] * 1.5

   = 10^3 * 0.7857( 0.0004) * 1.5

   = 0.4714 kg/s

Average heat transfer coefficient  

h = [tex]\frac{m(cp)}{A}[/tex]  ,  A = [tex]\pi DL[/tex]

L = 1 m , m = 0.4714 kgs , cp = 4.18

back to equation

h = [tex]\frac{0.4714*4.18}{\pi * 0.02 }[/tex]   = 1.970 / 0.0628 = 31.369 ≈ 31 kw/m^2 k

B) Heat transfer rate per meter length of pipe

Q = ha( ΔT ),  a = [tex]\pi DL[/tex]

   = 31 * 0.0628 * ( 80 - 20 )

  = 31 * 0.0628 * 60 = 116.808 KW

A four-cylinder four-stroke engine is modelled using the air standard Otto cycle (two engine revolutions per cycle). Given the conditions at state 1, total volume (V1) of each cylinder, compression ratio (r), rate of heat addition (Q), and engine speed in RPM, determine the efficiency and other values listed below. The gas constant for air is R =0.287 kJ/kg-K.

T1 = 300 K
P1 = 100 kPa
V1 = 500 cm^3
r = 10
Q = 60 kW
Speed = 5600 RPM

Required:
a. Determine the total mass (kg) of air in the engine.
b. Determine the specific internal energy (kJ/kg) at state 1.
c. Determine the specific volume (m^3/kg) at state 1.
d. Determine the relative specific volume at state 1.

Answers

Answer:

a) Mt = 0.0023229

b) = U1 = 214.07

c) = V₁  = 0.861 m³/kg

d) = Vr1 = 621.2

Explanation:

Given that

R = 0.287 KJ/kg.K, T1 = 300 K , P1 = 100 kPa , V1 = 500 cm³, r = 10 , Q = 60 kW , Speed N = 5600 RPM, Number of cylinders K = 4

specific heat at constant volume Cv = 0.7174 kJ/kg.K

Specific heat at constant pressure is 1.0045 Kj/kg.K

a)  To determine the total mass (kg) of air in the engine.

we say

P1V1 = mRT1

we the figures substitute

(100 x 10³) ( 500 x  10⁻⁶) = m ( 0.287 x  10³) ( 300 )

50 = m x 86100

m = 0.00005 / 86100 = 0.0005807 ( mass of one cylinder)

Total mass of 4 cylinder

Mt = m x k

Mt = 0.0005807 x 4

Mt = 0.0023229

b) To determine the specific internal energy (kJ/kg) at state 1

i.e at T1 = 300

we obtain the value of specific internal energy U1 at 300 K ( state 1) from the table ideal gas properties of air.

U1 = 214.07

c) To determine the specific volume (m³/kg) at state 1.

we say

V₁ = V1/m

V₁ = (500 x  10⁻⁶) / 0.0005807

V₁  = 0.861 m³/kg

d) To determine the relative specific volume at state 1.

To obtain the value of relative specific volume at 300 K ( i.e state 1) from the table ideal gas properties of air.

At T1 = 300 k

Vr1 = 621.2

Assume that the heat is transferred from the cold reservoir to the hot reservoir contrary to the Clausis statement of the second law. Prove that this violates the increase of entropy principle—as it should according to Clausius.

Answers

Answer: hello attached below is the diagram which is part of your question

Total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k  it violates Clausius increase of entropy which is Sgen > 0

Explanation:

Clausius statement states that it is impossible to transfer heat energy from a cooler body to a hotter body in a cycle or region without any other external factors affecting it .  

applying the increase in entropy principle to prove this

temp of cold reservoir (t hot)= 600 k

temp of hot reservoir(t cold) = 1220 k

energy (q) = 100 kj

total entropy change  = entropy change in cold reservoir + entropy change in hot reservoir = -0.166 + 0.083 = -0.0837 kj/k

entropy change in cold reservoir = Q/t cold = 100 / 600 = -0.166 kj/k

entropy change in hot reservoir = Q / t hot = 100 / 1220 = 0.083 kj/k

hence it violates  Clausius inequality of increase of entropy principle which is states that generated entropy has to be > 0

Consider an ideal gas undergoing a constant pressure process from state 1 to state
2 in a closed system. The specific heat capacities for this material depend on temperature in
the following way, cv = aT^b , cp = cT^d , where the constants a, b, c and d are known. Calculate

the specific entropy change, (s2 − s1), from state 1 to state 2.

Answers

Answer:

[tex]s_2-s_1=c\frac{T^d}{d}-Rg\ ln(\frac{P_2}{P_1})[/tex]

Explanation:

Hello,

In this case by combining the first and second law of thermodynamics for this ideal gas, we can obtain the following expression for the differential of the specific entropy at constant pressure:

[tex]ds=c_p\frac{dT}{T}-Rg\ \frac{dP}{P}[/tex]

Whereas Rg is the specific ideal gas constant for the studied gas; thus, integrating:

[tex]\int\limits^{s_2}_{s_1} {} \, ds=c\int\limits^{T_2}_{T_1} {T^{d-1}dT} \,-Rg\ \int\limits^{P_2}_{P_1} {\frac{dP}{P}} \,[/tex]

We obtain the expression to compute the specific entropy change:

[tex]s_2-s_1=c\frac{T^d}{d}-Rg\ ln(\frac{P_2}{P_1})[/tex]

Best regards.

An ideal turbojet engine is analyzed using the cold air standard method. Given specific operating conditions determine the temperature, pressure, and enthalpy at each state, and the exit velocity.

--Given Values--
T1 (K) = 249
P1 (kPa) = 61
V1 (m/s) = 209
rp = 10.7
rc = 1.8

Required:
a. Determine the temperature (K) at state 2.
b. Determine the pressure (kPa) at state 2.
c. Determine the specific enthalpy (kJ/kg) at state 2.
d. Determine the temperature (K) at state 3.

Answers

Answer:

a.  the temperature (K) at state 2 is  [tex]\mathbf{T_2 =270.76 \ K}}[/tex]

b.  the pressure (kPa) at state 2 is   [tex]\mathtt{ \mathbf{ p_2 = 81.79 \ kPa }}[/tex]

c.  the specific enthalpy (kJ/kg) at state 2 is [tex]\mathbf{h_2 = 271.84 \ kJ/kg}}[/tex]

d.  the temperature (K) at state 3 is   [tex]\mathbf{ T_3 = 532.959 \ K}[/tex]

Explanation:

From the given information:

T1 (K) = 249

P1 (kPa) = 61

V1 (m/s) = 209

rp = 10.7

rc = 1.8

The objective is  to determine the following:

a. Determine the temperature (K) at state 2.

b. Determine the pressure (kPa) at state 2.

c. Determine the specific enthalpy (kJ/kg) at state 2.

d. Determine the temperature (K) at state 3.

To start with the specific enthalpy (kJ/kg) at state 2.

By the relation of steady -flow energy balance equation for diffuser (isentropic)

[tex]h_1 + \dfrac{V_1^2}{2}=h_2+\dfrac{V^2_2}{2}[/tex]

[tex]h_1 + \dfrac{V_1^2}{2}=h_2+0[/tex]

[tex]h_2=h_1 + \dfrac{V_1^2}{2}[/tex]

For ideal gas;enthalpy is only a function of temperature, hence [tex]c_p[/tex]T = h

where;

[tex]h_1[/tex] is the specific enthalpy at inlet  = [tex]c_pT_1[/tex]

[tex]h_2[/tex] is the specific enthalpy at  outlet = [tex]c_pT_2[/tex]

[tex]c_p[/tex]  = 1.004  kJ/kg.K or 1004 J/kg.K

Given that:

[tex]T_1[/tex] (K) = 249

[tex]V_1[/tex] (m/s) = 209

[tex]h_2=C_pT_1+ \dfrac{V_1^2}{2}[/tex]

[tex]h_2=1004 \times 249+ \dfrac{209^2}{2}[/tex]

[tex]h_2 = 249996+21840.5[/tex]

[tex]\mathbf{\mathtt{h_2 = 271836.5 \ J/kg}}[/tex]

[tex]\mathbf{h_2 = 271.84 \ kJ/kg}}[/tex]

Determine the temperature (K) at state 2.

SInce; [tex]\mathtt{h_2 = c_pT_2 = 271.84 \ kJ/kg}[/tex]

[tex]\mathtt{ c_pT_2 = 271.84 \ kJ/kg}[/tex]

[tex]\mathtt{T_2 = \dfrac{271.84 \ kJ/kg}{ c_p}}[/tex]

[tex]\mathtt{T_2 = \dfrac{271.84 \ kJ/kg}{1.004 \ kJ/kg.K}}[/tex]

[tex]\mathbf{T_2 =270.76 \ K}}[/tex]

Determine the pressure (kPa) at state 2.

For isentropic condition,

[tex]\mathtt{ \dfrac{T_2}{T_1}= \begin {pmatrix} \dfrac{p_2}{p_1} \end {pmatrix} ^\dfrac{k-1}{k}}[/tex]

where ;

k = specific heat ratio = 1.4

[tex]\mathtt{ \dfrac{270.76}{249}= \begin {pmatrix} \dfrac{p_2}{61} \end {pmatrix} ^\dfrac{1.4-1}{1.4}}[/tex]

[tex]\mathtt{ 1.087389558= \begin {pmatrix} \dfrac{p_2}{61} \end {pmatrix} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ 1.087389558 \times 61 ^ {^ \dfrac{0.4}{1.4} }}=p_2} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ 3.519487255=p_2} ^\dfrac{0.4}{1.4}}[/tex]

[tex]\mathtt{ \mathbf{ p_2 = \sqrt[0.4]{3.519487255^{1.4}} }}[/tex]

[tex]\mathtt{ \mathbf{ p_2 = 81.79 \ kPa }}[/tex]

d. Determine the temperature (K) at state 3.

For the isentropic process

[tex]\mathtt{\dfrac{T_3}{T_2} = \begin {pmatrix} \dfrac{p_3}{p_2} \end {pmatrix}^{\dfrac{k-1}{k}}}[/tex]

where;

[tex]\mathtt{\dfrac{p_3}{p_2} }[/tex] is the compressor ratio [tex]\mathtt{r_p}[/tex]

Given that ; the compressor ratio [tex]\mathtt{r_p}[/tex] = 10.7

[tex]\mathtt{\dfrac{T_3}{T_2} = \begin {pmatrix} r_p \end {pmatrix}^{\dfrac{k-1}{k}}}[/tex]

[tex]\mathtt{\dfrac{T_3}{270.76} = \begin {pmatrix} 10.7 \end {pmatrix}^{\dfrac{1.4-1}{1.4}}}[/tex]

[tex]\mathtt{\dfrac{T_3}{270.76} = \begin {pmatrix} 10.7 \end {pmatrix}^{^ \dfrac{0.4}{1.4}}}[/tex]

[tex]\mathtt{{T_3}{} =270.76 \times\begin {pmatrix} 10.7 \end {pmatrix}^{^ \dfrac{0.4}{1.4}}}[/tex]

[tex]\mathbf{ T_3 = 532.959 \ K}[/tex]

what scale model proves the initial concept?

Answers

Answer: A prototype

Explanation:

The scale model that proves the initial concept is called a domain model.

What is a scale model?

A copy or depiction of something where all parts have the same dimensions as the original. A scale model is an image or copy of an object that is either larger or smaller than the object being represented's actual size.

A domain model is a type of conceptual model that is used to depict the structural elements and conceptual constraints within a domain of interest.

A domain model will include all of the entities, their attributes, and relationships, as well as the constraints that govern the conceptual integrity of the structural model elements that comprise that problem domain.

Therefore, a domain model is the scale model that proves the initial concept.

To learn more about the scale model, refer to the below link:

https://brainly.com/question/14341149

#SPJ2

A rate of 0.42 minute per piece is set for a forging operation. The operator works on the job for a full eight-hour day and produces 1,500 pieces. Use a standard hour plan.

Required:
a. How many standard hours does the operator earn?
b. What is the operator's efficiency for the day?
c. If the base rate is 9.80 per hour, compute the earnings for the day.
d. What is the direct labor cost per piece at this efficiency?
e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?

Answers

Answer:

b. What is the operator's efficiency for the day?

                                                      AND

e. What would be the proper piece rate (rate expressed in money) for this job, assuming that the above time standard is correct?

Explanation:

An 8-m long, uninsulated square duct of cross section 0.2m x 0.2m and relative roughness 10^-3 passes through the attic space of a house.. Hot air (80°C) enters an 8 m long un-insulated square duct (cross section 0.2 m x 0.2 m) that passes through the attic of a house at a rate of 0.15 m^3 /s. The duct is isothermal at a temperature of 60°C. Determine the rate of heat loss from the duct to the attic space and the pressure difference between the inlet and outlet sections of the duct.

Answers

Answer:

the rate of heat loss from the duct to the attic space = 1315.44 W

the pressure difference between the inlet and outlet sections of the duct  = 7.0045 N/m²

Explanation:

We know that properties of air 80⁰C  and 1atm  (from appendix table) are;

density p = 0.9994 kg/m³, Specifice heat Cp = 1008 J/kg.⁰C

Thermal conductivity k = 0.02953 W/m.⁰C, Prandtl number Pr = 0.7154,

Kinematic viscosity v = 2.097 × 10⁻⁵ m²/s

haven gotten that, we calculate the hydraulic diameter of square duct

Dh = 4Ac / P      { Ac = is cross sectional area of duct and P = perimeter}

now we substitute a² for Ac and 4a for P ( we know from the question that a = 0.2 m)

Dh = 4a² / 4a

Dh = 4(0.2)² / 4(0.2)

Dh = 0.2 m

Now we calculate the average velocity of air

Vₐ = Vˣ / Ac        { vˣ = volume flow rate of air}

Vₐ = Vˣ / a²      { Ac = a² }, we know that a = 0.2m₂, Vˣ = 0.15 m³

Vₐ = 0.15 / (0.2)²

Vₐ = 3.75 m/s

Next we calculate the Reynolds number

Re = Vₐ Dh / V

Re = (3.75 × 0.2) / 2.097× 10⁻⁵

Re = 35765.379

The  Reynolds number IS GREATER than 10,000

so the flow is turbulent and entry length in this case is nearly 10 times the hydraulic diameter

Lh ≈ Lt ≈ 10D

= 10 × 0.2

= 2m

As this length is quite small when compared to the total of tube, we assume fully developed flow for the entire tube length.

Now we calculate the Nusselt number from this relation;

Nu =  0.023 Re⁰'⁸ Pr⁰'³

so we substitute for Re and Pr

Nu = 0.023(35765.379)⁰'⁸ (0.7154)⁰'³

Nu = 91.4

Now calculate the convective heat transfer coefficient

h = Nu × K/ Dh

we substitute

h = 91.4 × 0.02953 W/m.°C / 0.2 m

h = 13.5 W/m².°C

We calculate the surface area of the square duct

Aₓ = 4aL       { L= length of duct}

we substitute

Aₓ = 4 × 0.2 × 8

Aₓ = 6.4 m²

Mass flow rate of air

m = pVˣ

we substitute again ( from our initials)

m = 0.9994 kg/m₃ × 0.15 m³/s

m= 0.150 kg/s

We calculate the exit temperature of the air from the duct

Te = Ts - (Ts -Ti) exp ( - hAₓ / mCp)

we know that

Ts = 60°C , Ti = 80°C, h = 13.5 W/m².°C , Aₓ = 6.4m², m = 0.150 kg/s , Cp = 1008 J/kg.°C

we substitute

Te = 60 - (60-80) exp(- ((13.5 × 6.4)/(0.15 × 1008))

Te = 71.3°

Now we calculate the rate of heat loss from the duct.

Q = mCp ( Ti -Te )

we substitute again

Q = 0.150 × 1008 × ( 80 - 71.3 )

Q = 1315.44 W

Next we calculate the estimated friction factors by using Haaland equation

1/√f = - 1.8log₁₀ [ 6.9/Re + (E/D)/3.7)¹'¹¹]

we know that E/D = relative roughness = 10⁻³

we substitute

so

1/√f = - 1.8log₁₀ [ (6.9/35765.379) + ( 10⁻³/3.7)¹'¹¹]

1/√f = - 1.8log₁₀ { 0.000192924 + 0.00010947}

1/√f = - 1.8log₁₀ 0.000302324  

√f =   1/6.334

f = (1/6.334)²

f = 0.02492

We calculate the pressure difference between inlet and outlet sections of the duct

ΔPl = fLPVa² / Dh × 2

ΔPl = {0.02492 × 8 × 0.9994 × (3.75)²} / 0.2 × 2

ΔPl = 2.8018 / 0.4

ΔPl = 7.0045 N/m²

Therefore pressure deference is 7.0045 N/m²

In a particular application involving airflow over a heated surface, the boundary layer temperature distribution may be approximated as

Answers

Answer:

Explanation:

In a particular application involving airflow over a heated surface, the boundary layer temperature distribution, T(y), may be approximated as:

[ T(y) - Ts / T∞ - Ts ] = 1 - e^( -Pr (U∞y / v) )

where y is the distance normal to the surface and the Prandtl number, Pr = Cpu/k = 0.7, is a dimensionless fluid property. a.) If T∞ = 380 K, Ts = 320 K, and U∞/v = 3600 m-1, what is the surface heat flux? Is this into or out of the wall? (~-5000 W/m2 , ?). b.) Plot the temperature distribution for y = 0 to y = 0.002 m. Set the axes ranges from 380 to 320 for temperature and from 0 to 0.002 m for y. Be sure to evaluate properties at the film temperature.

Summary of Possible Weather and Associated Aviation Impacts for Geographic/Topographic Categories Common in the Western United States.
Geographic/Topographic Descriptive Summary of Potential Aviation Impacts
Category of a Possible Weather That Could Impact Based on Weather
of Airport Location Aviation Operations
Along the US West coast,
with steep mountains to the east
(An example of this category is
Santa Barbara Airport, located
on the Southern California Coast,
at an elevation of 10 feet).
Within a valley in elevated terrain
surrounded by high mountains
(An example of this category is
Friedman Memorial Airport, located
in Central Idaho, at an elevation of 5300 feet).
In elevated terrain on the leeside of
high mountains
(An example of this category is Northern Colorado
Regional Airport, located in northern Colorado,
at an elevation of 5000 feet, on the leeside
of the Rocky mountains).

Answers

Answer: answer provided in the explanation section.

Explanation:

Weather phenomenons that would impart Aviation Operations in Santa Barbara -

1. Although winters are cold, wet, and partly cloudy here. It is in general favorable for flying. But sometimes strong winds damage this pleasant weather.

2.  The Sundowner winds cause rapid warming and a decrease in relative humidity. The wind speed is very high surrounding this area for this type of wind.  

3. Cloud is an important factor that affects aviation operations. Starting from April, here the sky is clouded up to November. The sky is overcast (80 to 100 percent cloud cover) or mostly cloudy (60 to 80 percent) 44% on a yearly basis. Thus extra cloud cover can trouble aviation operations.

4. The average hourly wind speed can also be a factor. This also experiences seasonal variations, these variations are studied carefully in the aviation industry. The windier part of the year starts in January and ends in June. In April, the wind speed can reach 9.5 miles per hour.

This and more are some factors to look into when considering wheather conditions that would affect aviation operations.

I hope this was a bit helpful. cheers

A 400 kg machine is placed at the mid-span of a 3.2-m simply supported steel (E = 200 x 10^9 N/m^2) beam. The machine is observed to vibrate with a natural frequency of 9.3 HZ. What is the moment of inertia of the beam's cross section about its neutral axis?

Answers

Answer:

moment of inertia = 4.662 * 10^6 [tex]mm^4[/tex]

Explanation:

Given data :

Mass of machine = 400 kg = 400 * 9.81 = 3924 N

length of span = 3.2 m

E = 200 * 10^9 N/m^2

frequency = 9.3 Hz

Wm ( angular frequency ) = 2 [tex]\pi f[/tex] = 58.434 rad/secs

also Wm = [tex]\sqrt{\frac{g}{t} }[/tex]  ------- EQUATION 1

g = 9.81

deflection of simply supported beam

t = [tex]\frac{wl^3}{48EI}[/tex]

insert the value of t into equation 1

W[tex]m^2[/tex] = [tex]\frac{g*48*E*I}{WL^3}[/tex]   make I the subject of the equation

I ( Moment of inertia about the neutral axis ) = [tex]\frac{WL^3* Wn^2}{48*g*E}[/tex]

I = [tex]\frac{3924*3.2^3*58.434^2}{48*9.81*200*10^9}[/tex]  = 4.662 * 10^6 [tex]mm^4[/tex]

Conductivity is the reciprocal of what?

Answers

The answer is electrical resubmitted pp

After a capacitor is fully chargerd, a small amount of current will flow though it. what is this current called?

Answers

Answer:

  leakage

Explanation:

That current is "leakage current."

A student lab group is brainstorming the design of an experiment that uses an ammeter (measures current) and different resistors to determine the effect of the resistance of a resistor upon the current in a simple circuit. Which Post-it note describes the most effective design?Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data. Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Move the ammeter to a different location in the circuit. Measure the current at this new location. Continue moving the ammeter to different locations within the circuit but be careful to keep the resistor in a fixed location. Measure and record all current values. Obtain a variety of batteries and build several circuits. Make sure that each circuit has at least one resistor and make sure that the resistance values are different in the different circuits. Place various ammeters in each circuit. Measure the number of batteries and the current for each of the circuits. Record the resistance values used in each of these circuits. Put a 10.0-ohm resistor in a circuit with a single D-cell. Measure the current in the circuit. Add a second D-cell and measure the current with two D-cells. Repeat trials for three, four, and five D-cells, being careful to get accurate current measurements for a fixed amount of resistance in each trial.

Answers

Answer:

  Put a 10.0-ohm resistor in the circuit. Measure the current in the circuit. Replace the 10.0-ohm resistor with a 20.0-ohm resistor. Measure the new current. Continue replacing the resistor with a different resistor of known resistance. Measure the current for each resistor. Record all data.

Explanation:

The only design that has resistance varying with everything else remaining the same is the first design. That would be what you'd want to do if you're exploring the effect of resistance on current.

Q1: You have to select an idea developing an application like web/mobile or industrial, it should be based on innovative idea, not just a simple CRUD application. After selecting the idea do the following: 1) How your project will be helpful and what problem this project addresses. (10-Marks) 2) Write down the requirements. (10Marks) 3) List the functional and non-functional requirements of your project. (10marks) 4) Which process model you will follow for this project and why? (10marks) 5) Draw the Level 0, and level 1 DFD of your application. (20marks)

Answers

Answer:

Creating an app is both an expression of our self and a reflection of what we see is missing in the world. We find ourselves digging deep into who we are, what we would enjoy working on, and what needs still need to be fulfilled. Generating an app idea for the first time can be extremely daunting. Especially with an endless amount of possibilities such as building a church app.

The uncertainty has always spawned a certain fear inside creators. The fear of creating something no one will enjoy. Spending hundreds of dollars and hours building something which might not bring back any real tangible results. The fear of losing our investment to a poor concept is daunting but not random. But simple app ideas are actually pretty easy to come by.

Great app idea generation is not a gift given to a selected few, instead, it is a process by which any of us are able to carefully explore step by step methods to find our own solution to any problem. Whether you are a seasoned creator or a novice, we have provided a few recommendations to challenge and aid you as you create your next masterpiece.

if I am right then make me brainliest

A permanent-magnet dc motor has the following parameters: Ra = 0.3 Ω and kE = kT = 0.5 in MKS units. For a torque of up to 10 Nm, plot its steady state torque-speed characteristics for the following values of Va: 100 V, 75 V, and 50 V.

Answers

Answer:

load speeds:

For V = 100 v  speed = 188 rad/sec

For V = 75 v   speed = 138 rad/sec

For V = 50 v   speed = 88 rad/sec

Explanation:

Given data

Ra = 0.3 Ω

Ke = Kt = 0.5

torque = 10 Nm

using  a constant torque = 10 Nm we can calculate the various load speed for the given values of 100 v , 75 v, 50 v

attached below is the detailed solutions and plot

The solid homogeneous cylinder is released from rest on the ramp. If θ= 40° , µs= 0.30 and µk= 0.20. Determine the magnitudes of the acceleration of the mass (W= 8lb) center G and the friction force exerted by the ramp on the cylinder.

Answers

Answer:

A) 13.80 ft/s^2

B) 1.714 Ib

Explanation:

Magnitude of acceleration center G

mass = W / g = 8 / 32.2 = 0.2484 Ib.s^2/ft

calculate the acceleration along x direction

A = ra

r = radius

a = angular acceleration

A = 6 in [tex]\frac{1 ft}{12 in}[/tex] * a

a= 2A

equation of the plane along the x-direction

w sin∅ - F = ma

8* sin40 - F = 0.2484 * a

hence F = 5.1423 - 0.2484 a

next find the moment of inertia along the z axis

I = 1/2 mr^2

  = 1/2 * 0.2484 * (6/12)^2  = 0.03105 Ib.ft.s^2

Applying moment balance equation

F * r = inertia * a

(5.1423 - 0.2484 a)*0.5 = 0.03105 * 2A

2.57115 = 0.1863 A      hence

A = 13.80 ft/s^2  ( acceleration of the cylinder )

B) Calculate the friction force exerted by the ramp on the cylinder

F = 5.1423 - 0.2484 A

  = 5.1423 - 0.2484 ( 13.80 )

  = 1.714 Ib

The magnitudes of the acceleration and the friction force are;

Acceleration = 13.8 ft/s²

Friction Force = 1.714 lb

The image of the solid homogeneous cylinder is missing and so i have attached it.

From the image we see that;

Weight; W = 8 lbRadius; r = 6 in = 0.5 ft

We are given;

Angle of incline; θ = 40°Coefficient of static friction; µ_s = 0.30 coefficient of kinetic friction; µ_k = 0.20

      We know that formula for weight is; W = mg

Thus; m = W/g

where g is acceleration due to gravity = 32.2 ft/s²

m = 8/32.2

mass; m = 0.2484 lb.s²/ft

     Now, to get the acceleration along the x-axis, we will use the formula;

a = rα

where α is angular acceleration. Thus;

a = 0.5α

α = 2a   ----- (eq 1)

    Now, resolving forces along the x-direction gives;

W*sinθ - F = ma

Plugging in the relevant values;

8*sin 40 - F = 0.2484a

F = 8*sin 40 - 0.2484a    -----(eq 2)

     Now, moment of inertia of the cylinder along the z-axis is gotten from;

I = ¹/₂mr²

I = ¹/₂ × 0.2484 × 0.5²

I = 0.03105 lb.ft/s²

     Taking equilibrium of moments we have;

F*r = I*α

Thus;

(8*sin 40 - 0.2484a)0.5 = 0.03105α

⇒ 2.57115 - 0.1242a = 0.03105α

⇒ 0.03105α + 0.1242a = 2.57115

From eq 1, α = 2a. Thus;

0.03105(2a) + 0.1242a = 2.57115

0.1863a = 2.57115

a = 2.57115/0.1863

a = 13.8 ft/s²

Formula for the friction force exerted by the ramp on the cylinder is;

F = 8*sin 40 - 0.2484a

F = 5.1423 - 0.2484(13.8)

F = 1.714 lb

Read more about cylinder moment of inertia at; https://brainly.com/question/7020147

A bona fide established commercial marketing agency is a business which is specifically devoted to public relations, advertising and promoting the services of a client. True or False

Answers

Answer:

True

Explanation:

Bona Fide is a Latin term which means in good faith or without any intention to deceive. The business established on a bona fide basis means that there is an absence of fraud. The marketing agency has devoted its services to public relations, advertising and promoting the services of clients. There is no intention of fraud in the business.

A single-threaded power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 006 for the collar and 009 for the threads, while the frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to raise and lower the load for

Answers

Answer:

the torque required to RAISE the load is Tr = 18.09 Nm

the torque required to LOWER the load is Tl = 10.069 ≈ 10.07 Nm

the Overall Efficiency e = 0.2199 ≈ 0.22

Explanation:

Given that; F = 5 kN, p = 5mm, d = 35mm

Dm = d - p/2

Dm = 35 - ( 5/2) = 35 - 2.5

DM = 32.5mm

So the torque required to RAISE the load is

Tr = ( 5 × 32.5)/2 [(5 + (π × 0.09 × 32.5)) / ( (π × 32.5) - ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tr = 81.25 × (14.1892 / 101.6518) + 6.75

Tr = 11.3414 + 6.75

Tr = 18.09 Nm

the torque required to LOWER the load is

Tl =  ( 5 × 32.5)/2 [(π × 0.09 × 32.5) - 5) / ( (π × 32.5) + ( 0.09 × 5))] + [( 5 × 0.06 × 45)/2]

Tl = 81.25 × 4.1892 / 102.5518 + 6.75

Tl = 3.3190 + 6.75

Tl = 10.069 ≈ 10.07 Nm

So since torque required to LOWER the load is positive

that is, the thread is self locking

Therefore the efficiency is

e = ( 5 × 5 ) / ( 2π × 18.09 )

e = 25 / 113.6628

e = 0.2199 ≈ 0.22

An AC voltage is represented by the relation v= 12. Determine the: (a) peak-to-peak voltage; (b) frequency; (c) root-mean-square voltage; (d) Period of the signal.

Answers

Answer:

The answer is below

Explanation:

An AC voltage is represented by the relation v= 12 sin(500πt). Determine the:

The equation of an AC voltage is given as:

[tex]V=V_msin(2\pi ft)[/tex]

Where Vm is the maximum value of voltage and f is the frequency

From V= 12 sin(500πt), Vm = 12, 2πft = 500πt

(a) The peak to peak voltage is total amplitude (both the negative and positive amplitude) of the voltage, it is the difference between the positive amplitude and the negative amplitude. The peak to peak voltage ([tex]V{p-p}[/tex]) is given as:

[tex]V_{p-p}=2V_m=2*12=24\ V[/tex]

b) The frequency is the number of oscillation per second. The frequency (f) is gotten from:

2πft = 500πt

2f = 500

f = 500/2

f = 250 Hz

c) The root mean square voltage is the dc value of the voltage. It is given by:

[tex]V_{rms}=\frac{V_m}{\sqrt{2} }=\frac{12}{\sqrt{2} }=8.5\ V[/tex]

d) The period (T) is the time taken to complete one oscillation, it is given by:

[tex]T=\frac{1}{f}\\ \\T=\frac{1}{250} =0.004\ s[/tex]

Punctuate or edit the following sentences. Your punctuation and/or revisions should reflect best TW style and grammar writing practices.
1. The author an expert in cybersecurity will speak via Zoom this Wednesday.
2. Williams' book contains many illustrations, this makes it quick reading.
3. Based on the available evidence the university administrators have opted for a hybrid format for the fall quarter which begins September 20.
4. (Thesis statement) Free laptops should be offered to all students who need them.

Answers

I inferred you want literal editing of the text above.

Explanation:

Here's a correction of the sentences:

1. The author, an expert in cybersecurity will speak via Zoom on Wednesday.

In this sentence, punctuation mark ( , ) was added and the word  'this' was replaced with 'on'.

2. Williams' book contains many illustrations, which makes it easy to read.

Added punctuation and made a revision of the sentence.

3. Based on the available evidence, the university administrators have opted for a hybrid format for the fall, which begins September 20.

Mainly added punctuations to make the senstence clarer.

4. (Thesis statement) I believe Free laptops should be offered to all students who need them.

Made a few additions.

Other Questions
The weights of ice cream cartons are normally distributed with a mean weight of ounces and a standard deviation of ounce. (a) What is the probability that a randomly selected carton has a weight greater than ounces? (b) A sample of cartons is randomly selected. What is the probability that their mean weight is greater than ounces? (a) The probability is nothing. (Round to four decimal places as needed.) (b) The probability is nothing. (Round to four decimal places as needed.) 0.25 L of aqueous solution contains 0.025g of HCLO4 (strong acid) what will be the Ph of the solution g 1.The following are types of living things excepta) Bactariab) fungic) Prolista d) lysosome Bearman and Brueckner (2001) found that teens who made a public virginity-until-marriage pledge became _______ likely to remain sexually abstinent than similar teens who do not make the pledge. during the course of songraphic exam, you notice lateral splaying of echoes in the far field. what can you do to improve the image slope of (-2,2) and (3,4) HELP ME PLEASEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE A student uses a spring scale attached to a textbook to compare the static and kinetic friction between the textbook and the top of a lab table. If the scale measures 1,580 g while the student is pulling the sliding book along the table, which reading on the scale could have been possible at the moment the student overcame the static friction? 1,140 g 1,580 g 820 g 1,860 g Find the value of x.76 What were the arrangements made by Jacob to meet Esau? ochieng had sh 250 as pocket money at the begining of the term.in the middle of the term he was left with 2 over five of this amount .how much did she spend Directions: Calculate the percent increase or decrease between the starting and endingquantities below. Round your answer to one decimal place.1. Start: 3End: 10 With the emergence of smartphones, users no longer have to carry a separate music player, a video game, a laptop, or a magazine to keep themselves entertained when traveling. A smartphone is loaded with a variety of applications to satisfy all the customer needs that different industries or products individually satisfied earlier. As a result, the smartphone industry has been posing a threat to a lot of other unrelated industries. What is this phenomenon best known as what is the square root of 450 Based on this map, which of the following countries would you expect to have the least opportunity for citizen political participation?A. CanadaB. MexicoC. EgyptD. Italy Lara is x years old and her two best friends are (x-2) and (x+2). Write an expression for the square of Laras age and the product of ages of Laras best friends.Please help with a detailed step by step thanks Point R is on line segment QS. Given RS=11 and QS=19, determine the length QR. a car moves for 10 minutes and travels 5,280 meters .What is the average speed of the car? Drag each label to the correct location on the table. Each label can be used more than once. A cross country coach records the number of miles his athletes on the Junior Varsity and Varsity teams ran today and displays the data in the provided dot plots. Given the shape of each distribution, determine which measures of center and spread are appropriate for him to use to summarize the data from each team. mean mean interquartile range interquartile range standard deviation standard deviation median median Which verb form best completes this conversation? Paco: Cunto dinero sacaste ayer? Marta: Ayer, yo _________ 8.000 pesos. A. saco B. saca C. saqu D. sacaron The manager of a savings and loan branch wants to estimate the average amount held in passbook savings accounts by the branch bank depositors. A random sample of 25 depositors is selected, and the results indicate a sample average of $4,750 and a sample standard deviation of $1,200. Given the 95% confidence interval estimates calculated above, if an individual had $4,000 ina passbook savings account, is this considered unusual? a. Yes b. Maybe c. Do not know d. No